Three Axis Gimbal Video Screen (L43)
Component Diagrams
1. Insert the front hooks
of the Gimbal in these
two slots
2. Insert the rear hook of
the Gimbal in this slot
Press the button and
pull down on the
Gimbal.
Removing the Gimbal
Gimbal Installation
2.5mm Video/Audio Cable
Gimbal Installation and Removal
Gimbal Specs
Operating Range
Net Weight
Image Sensor
ISO
Lens
Image Resolution
Video Resolution
SD Card Type
Operating Temperature
Hornet S Gimbal, Camera Specs
+0~-90º +/- 0.05º
200g
16 Megapixel
50~3200(automatic)
F/2.8, FOV/100 °, 28mm (35mm
equivalent) focus at ∞
(4608 x 3456)
Shutter Time 1.25-1/4000s(automatic)
4K@25FPS
2.7K@30FPS
1080P@60FPS
TF(Micro_SD) Card, ≥Class 10,
Max 64G
-10~50℃
720P@120FPS
Gimbal Instructions
1. Gimbal LED Status
Function KeyGimbal LED Status
①②③④
Image (Video or Still) Recording Indicator
2.Camera Control Button (on the Remote
Controller)
Record/Picture
Gimbal/ Up and Down
Installing the Video Screen
Press and hold the camera control button on the remote
controller for 3 seconds to begin recording. The set
resolution indicator will begin to blink to show recording
has started. Press and hold the camera control button for
3 seconds to end recording.
A quick press of the camera control button will take a still
picture.
Notice: you can press the camera button to intercept the
video pictures during recording (only effective under 1080P
/ 720P)
Using the Video Screen
Mobile Device Holder
Turn the drone and the remote controller on. To see how
to do this, look at <Hornet S Basic Instruction Manual>
Turn the Hornet S power ON
Notice: If the display shows "snow" the video signal is not
present - press the buttons on the back of the display one
by one until the video image appears on the screen
Video Screen Indicators
③. Remote Controller Signal Strength
④. Drone Uptime
⑤. Drone Battery Electric Current
⑥. Warnings
①. GPS Signal Strength
---
2D
3D
No GPS Signal
Weak GPS Signal
Strong GPS signal
②. Remote Controller Mode (To switch modes,
read the Remote Controller Instruction Manual)
STAB
MANU
ALTH
POSH
DVH
Disarmed
Manual
Set Altitude
Set Position (Can only be used
when there is a GPS Signal)
Maintain Speed
CEIL
FAIL
Reached the Max
Altitude
Lost Signal
Disarmed
No GPS Signal
Remote Controller
Signal Too Weak
Ascension and Rotation Angle of
the Drone (-180°~180°)
.⑦
⑧. Horizon
Distance (0~1000m) .⑨
⑩. Direction
Altitude (0~1000m) .⑪
Camera status information .
DISARMED
NO GPS!
LOSERSSI
Low Battery -
First Warning
Low Battery -
Second
LOWBATTERY 1
LOWBATTERY 2
Instruction Manual
Hornet S
G3S
Three Axis Gimbal
www.JYU.com
Taking Pictures or Video
Press and hold the camera control button on the remote
controller for 3 seconds. The set resolution indicator will
begin to blink to show recording has started. Press and
release the camera control button to change the resolution
setting until the corresponding status light flashes (The
default resolution is 1080P@60FPS).
Setting the Camera Resolution
The Hornet S video signal has been paired with the
Remote Controller at the factory so you should see
video immediately
Pull the mobile device holder out of the Remote Controller
Place the video screen in the holder and securely press it
in place as shown in diagram 1
Connect the screen to the Remote Controller using the 2.5
mm video cable as shown in diagram 2
Status Light and Resolution Pairing Table
Video
Resolution Image
Resolution
LED① LED② LED③ LED④
4K@25FPS
2.7K@30FPS
1080P@60FPS
720P@120FPS
16M
(4608 x 3456)
Key : = Bright = Dull
10
⑫
⑫
