Kadink KDOWK0061 User manual

1/4
This design and instruction booklet is subject to copyright.
www.o󰀩ceworks.com.au
INSTRUCTIONS
Ages 6+
Adult supervision recommended
OFFICEWORKS LTD, 236-262 EAST BOUNDARY ROAD
EAST BENTLEIGH VIC 3165 AUSTRALIA
UNICORN FELT SEWING KIT
KDOWK0061

2/4
Contents
20 x felt unicorn pieces
1 x 21g bre lling
4 x yarn pieces
3 x cotton thread
2 x plastic needles
1.
2.
3.
4.
5.
6.
Under
Over
Back Stitch
Starting your stitch
(Do this for every section)
Ending your stitch
(Do this for every section)
Blanket Stitch
1.
3.
2.
4.
Needle through the hole. Loop around & through next hole
(leaving small amount of slack).
Needle through loop made from slack.
Pull rmly.
Repeat steps 2 & 3.
1. Cut length according to area of sew.
2. Thread through ¼ of cut length through needle
(this is your tail end).
3. Tie a knot in the tail end of the thread.
4. Begin stitch.
5. Adjust your tail end as you sew, this needs to stay
shorter than the end you are working with.
1. Using a method like the blanket stitch. Needle
through the hole, loop around and through the next
hole with slack.
2. Needle through the same loop made from slack.
Do this twice to create a knot that will hold the
stitch.
3. Continue the stitch you were working on for this
section through 3 more holes.
4. Then cut the remaining length.

3/4
Step 3.
Using approximately 20cm of pink thread,
on one of the wings, back stitch row 1
through pre-made holes on both pieces
of wing to pinch both pieces together
(Repeat for row 2). On the row 3 of the
wing, using approximately 30cm pink
thread, back stitch a nished wing to a
unicorn body piece by starting your stitch
on the inside of the body piece. Use the
5 pre-made holes to attach the wing.
Repeat this process for the remaining
wing and body piece (Remember to
attach the wings to the outside of the
each of the unicorn body pieces).
Step 4.
Back stitch the nose and eye details using the black cotton
thread supplied. (Eye approx. 20cm of thread, nose approx.
5cm of thread).
Step 5.
Use approximately 8cm lengths of the pink thread for the
following. Take the smallest pink felt shapes and sew these onto
the unicorn face to create rosy cheeks. Then sew on the ears.
Pull the thread tight to pinch the ear. Tie a knot using both ends
of the thread.
Step 6.
Cut the coloured yarn into approximately 10cm lengths
to create the unicorns mane. Using 1 of the 4 pre-made
mane holes on the top gusset of the unicorn, thread through
one of the 10cm lengths. Make sure to tie a knot on the backside of the gusset to secure. Repeat this for the
remaining coloured lengths using all the pre-made mane holes to create the mane.
Horn Mane
Step 7.
Using white thread (approximately 25cm) starting at the top, sew the horn
together as per the diagram (do not sew to tightly to give the horn a round
shape). Once you reach the bottom, add a small amount of ber ll, and
sew the horn to the top gusset using the 4 holes as per above diagram.
Row 1
Row 2
Row 3
Side A Side B
Attach ear
Back stitch eye
(Start here)
Back stitch nose
(Start here)
Attach cheek
Stitch
Example Start Sewn horn
Step 1.
Remove all of the contents from your kit.
Step 2.
Using pink thread, sew 2 felt wing pieces together ¾ of the
way – using the blanket stitch method. Insert lling and
then complete stitching to close. Repeat this process for
the remaining 2 felt wing pieces.
(Approx. 80cm of thread).
Instructions
Start
Finish
Insert bre
ll here

4/4
Step 10.
Continuing on, line up the top gusset, make sure the horn is in front of the mane,
and blanket stitch each side of the unicorn body to the top gusset until both sides
are attached.
Step 11.
Once you have completed all the stitching, stu󰀨 the unicorn belly with bre lling and
nish by closing the belly (underside gusset) using blanket stitch. (Approx. 42cm of
white thread).
Step 12.
To nish, back stitch the unicorn mouth across the outside of the
gusset to the other side using black thread. (Approx. 17cm of
black thread).
Step 9.
Back stitch the tail pieces
between the body pieces and
continue blanket stitching around
the unicorn body until you reach
the start of the top gusset at the
back of neck. (Approx. 200cm of
white thread).
Stop here Attach
tail here
Stitch
across
gusset
Step 8.
Starting below the tail, line up the
underside gusset to the unicorn body
pieces, one side at a time. Then
blanket stitch around the perimeter of
the underside gusset, attaching both
unicorn body sides until you return to
the tail area, and the gusset is attached.
Remember to sew the pink hooves on
top of the unicorn body sides as you go.
Ensure the belly is left open. (Approx.
220cm of white thread).
Fold
Start
here
Finish
here