Kali Lone Pine LP-6-WM User manual

KALI AUDIO Lone Pine Wall Mount Adapter User’s Guide 1
Project Lone Pine
Professional Studio Monitors
LP-6-WM
LP-8-WM
Wall Mount Adapters
User’s Guide

KALI AUDIO Lone Pine Wall Mount Adapter User’s Guide 2
Important Safety Information
DISCLAIMER – Kali Audio, Inc. has extended every effort to ensure the accuracy and
completeness of this manual. However, Kali Audio, Inc. does not claim that the infor-
mation covers all installation or operational variables. The information contained in this
document is subject to change without notice or obligation of any kind. Regarding the
information contained herein, Kali Audio, Inc. makes no representation of warranty, ex-
pressed or implied, and assumes no responsibility or accuracy, sufficiency, or complete-
ness of the information contained in this document.
1. Read these instructions.
2. Keep these instructions.
3. Follow all warnings.
4. Heed all instructions.
5. These wall mount adapters are for use only with the Allen Technology
Group™ MM-10-BT and OmniMount™ 25.0 W wall mounts. The use of any
other wall mount is not recommended, and may result in serious personal
injury, damage to personal property, or voiding of factory warranty.
6. Kali Audio, Inc., Has only tested the two wall mounts listed in this user’s
manual. These wall mounts are readily available worldwide, reliable, and well-
made. The use of any other wall mount solution will void the warranty of the
speaker, and could result in serious injury or damage to personal property.
7. It is the responsibility of the installer to properly install one of the recom-
mended wall mounts for each Kali speaker being installed. Failure to follow
all instructions accompanying those wall mounts can result in serious per-
sonal injury, damage to personal property, or voiding of factory warranty.
WARNING: FAILURE TO READ, THOROUGHLY UNDERS STAND, AND FOLLOW ALL
INSTRUCTIONS CAN RESULT IN SERIOUS PERSONAL INJURY, DAMAGE TO PERSONAL
PROPERTY, OR VOIDING OF FACTORY WARRANTY!

KALI AUDIO Lone Pine Wall Mount Adapter User’s Guide 3
Recommended Wall Mounts
The LP-6-WM and LP-8-WM are adapter plates to allow the LP-6 and LP-8
studio monitors to be fitted to a wall mount. When wall mounting, it is nec-
essary to buy one wall mount adapter and one 3rd party wall mount per
speaker being mounted.
Kali Audio, Inc, has tested and recommends the following wall mounts:
Allen Technology Group™ MM-10-BT
Website User’s Manual
OmniMount™ 25.0 W
Website User’s Manual
Are the LP-6-WM and LP-8-WM interchangeable?
No. The LP-6-WM is only for use with the LP-6 and LP-6 White studio moni-
tors. The LP-8-WM is only for use with the LP-8 studio monitor.
Can I mount the LP-6-WM or LP-8-WM directly to a wall?
No. Only the use of the Allen Technology Group™ MM-10-BT and the
Omnimount™ 25.0 W is supported.
Due to the placement of the Wall Mount
adapter relative to the monitors’ inputs, it
will be necessary to use cables with 90° con-
nectors going into the monitors. Unless it is
totally necessary to use XLR or RCA, Kali rec-
ommends using a TRS cable with this sort of
connector.
Required Connectors

KALI AUDIO Lone Pine Wall Mount Adapter User’s Guide 4
Installation
The LP-6-WM and LP-8-WM can be simply installed by removing several screws from
the back of the loudspeaker, placing the wall mount plate, and replacing the screws.
You will need a Phillips-head screwdriver for this installation
1. Install the signal cable and set volume
and all dip switches on the back of the
speaker as desired. It will be difficult to
make adjustments once the wall mount
adapter is installed.
2. Remove the middle four screws from
the back of the speaker, and put them
somewhere safe.
3. Line up the holes on the back of
the speaker with the holes on the wall
mount adapter. Carefully screw the
screws back into the speaker until they
are tight.

KALI AUDIO Lone Pine Wall Mount Adapter User’s Guide 5
Installation
When finished, your speaker should look like this:
Warranty
What does this warranty cover?
This warranty covers defects in materials or workmanship for a period of one year (365
days) after the purchase date of the product.
What will Kali do?
If your product is defective (materials or workmanship,) Kali will replace or repair the
product at our discretion - free of charge.
How do you initiate a warranty claim?
Send an email to [e-mail] with the subject line: Defective Wall
Mount Adapter. Attach photos of your defective unit, and we will initiate a replacement.