Proper iPad Swivel Stand User manual

iPad Swivel Stand
Installation Guide

2
Power
This product includes a (2m) 8-Pin Lightning to USB cable.
Before installation, ensure your device is within reach of
a power source. If you are plugging your iPad directly into
a wall outlet, it is recommended that you use the ocial
Apple Power Adapter included with your iPad, or a genuine
replacement from Apple.
Cable Management
Before installation, consider the route your cable will need to
take to reach a power source. Try to keep the cable away from
any potential hazards or spills. You have the choice of either
i. running the power cable out of the rear of the stand, which
will require no drilling, or, ii. tunneling the power cable
through the table/countertop, which will require drilling.
Drilling
If you choose to tunnel the cable through your surface, you
will need to make a 35mm hole for the cable to pass through.
To maximise the available surface area for adhesion of the
stand, try not to exceed 35mm. Consider if your surface is
suitable for this, and if possible, use a licensed professional.
Loosening and Tightening Screws
Overtightening the screws may cause damage to the
stand, or your device. If you feel as though something isn’t
tting together correctly for any reason; rst re-read the
instructions to ensure you haven’t missed anything, then
contact our customer support team for further assistance.
Adhesive
This stand adheres to surfaces using a permanent adhesive.
Before installation, give your surface a quick clean, ensuring
it is free from dust, oil, or any other residue that could keep
the adhesive from mounting as securely as possible.
Once you adhere the product to your surface, press down
rmly (holding the body of the stand, not the iPad or frame)
for at least 30 seconds, and, if possible, allow 24 hours
without use to let the adhesive fully bond to the surface.
More Information
If you require any assistance, visit our helpdesk:
> help.studioproper.com
or contact our customer support team with any questions:
> [email protected]
Before You Begin

3
Product Overview
Apple iPad
This product is designed to be compatible with
Apple iPad (5th & 6th Generation).
(Not included with the stand)
Powered iPad Lock Belt
This is the ‘belt’ that secures your iPad in place,
conceals the charging cable, and keeps your device
securely attached to the stand.
Swivel Stand
The main body of the Swivel Stand.
Adhesive Base
The base keeps the stand sturdy, and provides a
large surface area for adhesion.

4
Use the Security Tool for star
shaped screws like this.
Use the Hex Key for hexagonal
screws shaped like this.
Note: Only required for removing
the Lock Belt from the stand.
The Toolkit
Security ToolHex Key / Pick Tool
The Pick Tool is used to
lift o end caps.

5
Mounting Options
Tunnel
Tunneling your cable through the table surface
requires you to make a 35mm hole directly beneath
the stand, through the table/countertop.
Tail
Tailing your cable from the rear of the stand
requires you to feed the cable through the stand
before you secure it down.
i. ii.

6
1.
2.
Use the Pick Tool to lift o the metal
end caps from the Lock Belt.
Use the Security Tool to remove the 4
screws holding the cassette in place.
2
1

7
3.
4.
Lift the inner cassette out of the
aluminum frame of the Lock Belt.
This is where you will secure the iPad.
Use the Security Tool to remove the 2
screws holding the end cap in.
3
4

8
5.
6.
Ensure the Lightning port is aligned in
the correct orientation.
(See Home button indentation)
Re-install the screws with the
Security Tool to keep your iPad locked
into place.
6
5

9
7.
8.
Connect the Lightning cable to the
iPad. There are clips underneath to
hold it in place.
Pass the USB end of the cable through
the stand.
Note: See Mounting Options on Page 5.
7
8

10
Use the Security Tool to attach the
iPad to the frame.
Peel the backing o the adhesive base.
Note: If you intend to tunnel the
charging cable beneath the stand, you
will rst need to make a 35mm hole.
See Mounting Options on Page 5.
9.
11.
10. Push the end caps back onto the frame
to secure the iPad in place.
9
10
11

11
Press down rmly on the base to
adhere the stand in place.
12.
13. If possible, leave the stand overnight,
allowing the adhesive time to bond to
the surface properly before use.
12
13