K&F VIDA L Flying Frame User manual

K&F VIDA L Flying Frame
Important Information,
Please Read Before Use!
KLING & FREITAG GmbH
Junkersstraße 14
D-30179 Hannover
TEL [phone]
FAX [phone]
www.kling-freitag.de
User's Manual
Translation of the original instructions
Version 1.6
Released: 24.04.2017

User's Manual K&F VIDA L Flying Frame
KLING & FREITAG GMBH © 2017 Version 1.6 Page 3 of 40
Table of contents
1Introduction 5
1.1 Icons Used 5
1.2 About this Manual 5
2Product Description 6
2.1 Flying frame 6
2.1.1 Items Included VIDA L Flying Frame 6
2.1.2 Overview of flying frame Components 6
2.2 Connector set 6
2.3 Flying Frame Extension 7
2.3.1 Items Included: flying frame extension 7
2.3.2 Overview of VIDA L flying frame extension 7
2.4 Identification plate 8
2.5 Product Labels and Icons 8
3Intended Use 8
4Safety Instructions 10
4.1 Safety Instructions for Flying Configurations 10
5VIDA L Setup 12
5.1 Required Tools 12
5.2 Preparing the flying frame 12
5.2.1 Down-tilt Angle 12
5.2.2 Load Adapter 14
5.2.3 Moving the Load Adapter 15
5.2.4 Mounting the flying frame extension 17
5.3 Mounting the VIDA L flying frame 17
5.3.1 Attaching a flying frame to a Speaker 19
5.3.2 Mounting the flying frame with connector sets 22
5.4 Setting up a Speaker Array 25
5.5 Stacking Speakers 27
5.6 Dual-fall Arrays 30
6Dismounting a Flying Speaker Array 31
6.1 Dismounting onto Case Bases 31
6.2 Dismounting into Upright Cases 34
7Dimensions and Weight 35
7.1 VIDA L Flying Frame-Dimensions and Weight 35
7.2 VIDA L Flying Frame with VIDA L Flying Frame Extension-Dimensions and
Weight 36
8Transportation and Storage 37

User's Manual K&F VIDA L Flying Frame
KLING & FREITAG GMBH © 2017 Version 1.6 Page 4 of 40
9Care and Maintenance 37
10 Declaration of Conformity (CE) 38

User's Manual K&F VIDA L Flying Frame
KLING & FREITAG GMBH © 2017 Version 1.6 Page 5 of 40
1. Introduction
Thank you for purchasing a KLING & FREITAG product. To guarantee trouble-free operation
and enable the KLING & FREITAG VIDA L speaker system to achieve its full potential, please
read these user's manual carefully before use. This item is a quality accessory for the VIDA L
speaker system. Combining it with your existing speaker system creates an extremely versatile
pro-grade tool that meets all requirements in terms of audio quality and safe installation.
1.1 Icons Used
Warning
This icon indicates a risk of injury or death. Not following these instructions may result in
serious health problems including potentially fatal injuries.
Caution
This icon indicates a possibly dangerous situation. Not following these instructions may cause
minor injuries or damage.
This icon marks instructions for proper use of the described products. Not following these
instructions may cause malfunctions or damage.
Tip
This icon marks information provided for simplified use of the described products.
1.2 About this Manual
© KLING & FREITAG GmbH. All rights reserved.
All specifications regarding the features of the described products and applicable safety
guidelines provided in this manual are based on information available at the time of
publishing.
We assume no responsibility for technical specifications, dimensions, weights, and properties.
All information in this manual is subject to change without notice.
To ensure safe operation, all persons using the speaker accessories must have access to this
guide and all other relevant material during installation. The speaker accessories must not be
set up nor operated unless this manual has been read, understood and kept readily available
on site.
All KLING & FREITAG manuals are originally authored in German.
KLING & FREITAG spare manuals are separately available for order or can be downloaded
from our website: www.kling-freitag.de.
Contact Us: [email protected]
KLING & FREITAG GMBH, Junkersstr. 14, D-30179 Hannover
Phone [phone], fax [phone] (other countries)

User's Manual K&F VIDA L Flying Frame
KLING & FREITAG GMBH © 2017 Version 1.6 Page 6 of 40
2. Product Description
The VIDA L flying frame is designed for installing and flying up to 8 VIDA L speakers. Use
this flying frame only for flying and tilting VIDA L speakers. When used in combination with
a second VIDA L flying frame unit and a flying frame extension, tilt angles of up to 90° can
be achieved, for example, for installing horizontal arrays.
2.1 Flying frame
The VIDA L flying frame features a bore rail at the top. It allows for quickly and safely fixing
the load adapter in 22 positions using 2 fixing pins. The various positions allow for achieving
a down-tilt angle of the speaker or array (whichever is used). To find the appropriate
position, run a simulation of the overall setup using the VIDA App to find the best load-
adapter position and tilt angle.
In addition, the VIDA L flying frame provides 4 parking bays for the optional connector sets
plus a fixture for the VIDA L flying frame extension.
The flying frame also has 2 built-in movable clips used for locking unused connector sets in
their parking bays and securing those in operation to the flying frame.
2.1.1 Items Included VIDA L Flying Frame
• (1x) flying frame for suspending VIDA L speakers
• (1x) User manual
2.1.2 Overview of flying frame Components
1
2
3
4
6
7
5
8
1. (1x) Flying frame
2. Bore for securing the flying frame extension
3. (1x) Shiftable load adapter
4. (2x) Fixing pin for fastening
5. Bore rail with indexes for fastening the load adapter
6. Connecting pin for fastening and securing various connecting adapters
7. Magnetic clips
8. Park slot for connector sets (optional)

User's Manual K&F VIDA L Flying Frame
KLING & FREITAG GMBH © 2017 Version 1.6 Page 7 of 40
2.2 Connector set
The optional connector sets are required for attaching the VIDA L flying frame to the bottom
of a VIDA L speaker. Such a configuration is required when flying one or more speakers as a
horizontal array.
After operation and dismounting, you can lock and store the connector sets in the flying
frame parking bays.
• (4x) VIDA L connector set for attaching a VIDA L flying frame to the bottom of a
VIDA L speaker
• (1x) User's Manual
2.3 Flying Frame Extension
The VIDA L flying frame extension is used for achieving a larger down-tilt angle or for
configuring dual-fall suspension.
2.3.1 Items Included: flying frame extension
• (1x) flying frame extension for increasing the down-tilt angle and for securing flying
VIDA L speakers
• (1x) User's Manual
2.3.2 Overview of VIDA L flying frame extension
1
2
3
4
1. (1x) VIDA L Flying Frame Extension

User's Manual K&F VIDA L Flying Frame
KLING & FREITAG GMBH © 2017 Version 1.6 Page 8 of 40
2. Stationary suspension / bearing point
3. Extended bore rail for fastening the load adapter
4. (2x) K&F suspension pins for fastening the flying frame extension
2.4 Identification plate
4
5
6
7
1
2
3
1. Manufacturer logo
2. Manufacturer address
3. Product name
4. Safety Instructions
5. Serial number, weight
6. CE mark
7. TÜV certificate
2.5 Product Labels and Icons
4
5
1
2
3
1. Angle grid
2. Max. load (single-fall suspension)
3. Max. load (dual-fall suspension)
4. Safety instructions
5. Safety instructions on operating rigged speakers (see the Attaching a Flying Frame to a
Speaker chapter on page 19)
6. CE mark
7. TÜV certificate

User's Manual K&F VIDA L Flying Frame
KLING & FREITAG GMBH © 2017 Version 1.6 Page 9 of 40
3. Intended Use
The VIDA L flying frame is designed for flying a maximum of 8 VIDA L speakers at a specific
tilt angle.
For commercial use in interior spaces as specified in this document only!
Unless otherwise stated, use only KLING & FREITAG original parts for mounting the speakers.
Never use other parts (in particular, parts not made by KLING & FREITAG).
Any other use not described in this document is not an intended use

User's Manual K&F VIDA L Flying Frame
KLING & FREITAG GMBH © 2017 Version 1.6 Page 10 of 40
4. Safety Instructions
Warning
The information described here does not relieve the user of the duty to follow the given
safety requirements and legal regulations.
Only qualified technicians are permitted to perform the installation steps. Be sure to use
personal protective equipment at all times.
The technicians responsible for installing the system on site are responsible for and
guarantee safe setup and use.
To prevent injury and damage, be sure to securely place or suspend the speaker array as
specified in the DGUV regulations 17 and 18 or similar locally applicable accident-control
standards.
Unless otherwise stated, use only KLING & FREITAG original parts for mounting the speakers.
Never use other parts (in particular, parts not made by KLING & FREITAG).
In mobile and stationary installations, always use installation parts supplied by KLING &
FREITAG.
Be sure to always visually inspect all array components before use. In fixed installations,
regularly check all array components for signs of wear. Visual inspection includes checking all
speaker-system and flying frame components, supporting components (e.g. trusses, ceiling
structures, etc.), and all screwed connections. During the inspection, check all flying-system
components carefully for deformation, cracks, bolt damage, and corrosion. Remember
checking the fixing pin and pin bolts for proper functioning. Also check slings and lifts (e.g.
shackles, chains, and steel ropes) carefully for wear and deformation. If there are signs of
wear, cracks, or deformation, etc., replace the affected parts immediately. See also the “Care
and Maintenance” chapter on page 37.
4.1 Safety Instructions for Flying Configurations
Warning
Loudspeakers falling down impose a deadly risk for people standing near-by!
Never use the array if you have any doubt regarding its safety and reliability!
Only qualified event technicians are permitted to suspend a VIDA L system.
Never suspend the speakers without the correct flying frame.
Maximum-load specifications refer to configurations including cabling and any fittings.
Use the simulation function provided by the VIDA App software to find out whether your
configuration loads the flying frame as allowable. The VIDA App software does not account
for the weight of extra cabling and fittings! Remember to take any such extra weight into
account—if necessary, reduce the number of speakers as required.
Ensure that all connections are secured against coming loose and that only authorized,
statically tested and correctly sized supports, mounting equipment, wire ropes and chains
are used. Follow the relevant specified safety factors. Be sure to follow the relevant national
specifications, norms, and safety regulations.
Note that every suspension point as well as the supporting structure of the building (i.e.
ceiling points, cross beams and stage or PA tower, etc.) must be capable of carrying the total
load of the system (including cabling and additional fittings).
Note that the suspension points on the hall ceiling (i.e. shackles, attachment points, or
chain hoists) must comply with the DGUV regulations 17 and 18 or similar locally applicable
accident-control standards. The maximum load must have been certified by an authorized
expert. When in doubt, request a confirmation by local authorities.
Also follow the operating and safety instructions supplied with the product you intend to
suspend the flying frame from (e.g. a truss). Never mount the flying frame to a product if
there is no information on safe use and maximum load.
Even with two-fall suspension, each chain and motor must be capable of carrying the entire
array mass! Make sure that the motor chains hang down vertically and are not twisted, and
that the motors are located at the required positions.

User's Manual K&F VIDA L Flying Frame
KLING & FREITAG GMBH © 2017 Version 1.6 Page 11 of 40
During setup, installation, and dismounting, when using chain hoists that do not comply
with the DGUV regulations 17 and 18 or similar locally applicable accident-control standards,
make sure no persons stand in the danger zone below or near the speaker system.
When using a BGV C1 motor, the VIDA L system is intrinsically safe, so no secondary safety
components are required in operation;
Never use signal cables or power cords for suspending, aligning, or securing the systems. Run
the cables in a way that nobody can trip over them.
Ensure there is sufficient clear space for assembling and suspending the array on-site.
Remember that the array may swing out wide!
Permit only personnel directly involved with assembly or disassembly to access the working
area. The person in charge must announce all flying frame lifting and lowering activities
beforehand and make sure all people attending are aware. In this case, all persons present
must leave the swing and lifting range immediately.
Never use the flying frame for lifting or safeguarding persons or objects other than the
above speakers.
Never use an array as a climbing aid.

User's Manual K&F VIDA L Flying Frame
KLING & FREITAG GMBH © 2017 Version 1.6 Page 12 of 40
5. VIDA L Setup
Warning
For commercial use as specified in this document only!
To prevent personal injury and damage, be sure to securely place or suspend the speaker as
specified in the locally applicable standards.
The information described here does not relieve the user of the duty to follow the given
safety requirements and legal regulations.
The persons in charge with putting up the speaker are responsible for safe setup and use and
must guarantee it.
In mobile and stationary installations, always use installation parts supplied by KLING &
FREITAG. KLING & FREITAG
Unless otherwise stated, use KLING & FREITAG original parts only. KLING & FREITAGNever
use other parts (in particular, parts not made by KLING & FREITAG).
Be sure to always visually inspect all safety-related speaker and accessory components before
use. In fixed installations, check the speaker for signs of wear at regular intervals. If there are
signs of wear, cracks, or deformation, etc., replace the affected parts immediately.
5.1 Required Tools
The following is required for mounting the VIDA C to the VIDA L speaker:
• Allen wrench (6 mm)
5.2 Preparing the flying frame
Using the VIDA App software, you can simulate both single-fall and dual-fall configurations.
• For a single-fall configuration, you require 1 flying frame plus 1 load adapter.
• For a dual-fall configuration, you will need to use 2 flying frames, 1 load adapter, and
1 flying frame extension.
To prepare the flying frame, perform the following steps:
• Simulate setup using the VIDA App including down-tilt angle determination
• Identify the required location of a load adapter and install the adapter
• Mount the flying frame extension (if necessary)
• Prepare a second flying frame including connector set installation (if necessary)
5.2.1 Down-tilt Angle
Warning
Danger! Risk of injury from falling objects!
Improperly mounted speakers are not safe for suspending. Objects falling down impose a
deadly risk for people standing near-by!
With these array setups, be sure not to use the following bore combinations:
VIDA L without VIDA C:
7 x VIDA L 28/29 to 29/30 (forbidden)
8 x VIDA L 26/27 to 29/30 (forbidden)
VIDA L with VIDA C:
5 x VIDA L with VIDA C 29/30 (forbidden)

User's Manual K&F VIDA L Flying Frame
KLING & FREITAG GMBH © 2017 Version 1.6 Page 13 of 40
6 x K&F VIDA L with K&F VIDA C 26/27 to 29/30 (forbidden)
7 x VIDA L with VIDA C 24/25 to 29/30 (forbidden)
8 x VIDA L with VIDA C 23/24 to 29/30 (forbidden)
At least 1 flying frame and 1 flying frame extension (if necessary) are required for flying
VIDA L arrays.
The load adapter can be mounted to various positions on the flying frame. In addition, you
can choose between full-grid and half-grid configurations.
Use the VIDA App for simulating the intended configuration and determine the required
down-tilt angle.
See the tables below for minimum and maximum values for various VIDA L speaker-array
configurations with or without VIDA C and single-fall or dual-fall suspensions.
Where a negative angle is specified, the speaker faces downwards.
Table 1: Single-fall suspension without/with VIDA C
Array
size
Minimum angle Maximum angle
1 18.9 / 20.3 -51.5 / -49.2
2 9.0 / 10.3 -33.4 / -31.4
3 5.8 / 6.8 -23.9 / -22.4
4 4.2 / 5.0 -18.4 / -17.3
5 3.3 / 4.0 -14.9 / -13.9
6 2.7 / 3.3 -12.5 / -9.7
7 2.3 / 2.8 -9.8 / -7.4
8 2.0 / 2.5 -7.9 / -6.1

User's Manual K&F VIDA L Flying Frame
KLING & FREITAG GMBH © 2017 Version 1.6 Page 14 of 40
Table 2: Dual-fall suspension without/with VIDA C
Array
size
Minimum angle Maximum angle
1 0.0 -90.0
2 0.0 -90.0
3 0.0 -90.0
4 0.0 -90.0
5 0.0 -70.0 / -45.0
6 0.0 -40.0 / -30.0
7 0.0 -25.0 / -20.0
8 0.0 -20.0 / -15.0
5.2.2 Load Adapter
Warning
Danger! Risk of injury from falling objects!
Improperly mounted speakers are not safe for suspending. Objects falling down impose a
deadly risk for people standing near-by!
In larger arrays of VIDA L or VIDA L with VIDA C some pickpoints may not be used. Please
refer to chapter 'Down-tilt Angle' from page 12.
Use the VIDA App for determining the flying frame bores to insert the load adapter into.
Refer to VIDA App calculations for correct selections. The indicated numbers refer to the bore
numbers on the flying frame. With bore 13 or higher, you need to use the VIDA L flying-
frame outrigger.
Front
As either side of the load adapter can be used, you can set the position in half-steps. This
doubles the flying-frame bore grid and thus the adjustment options. Load adapters have
a 1/1 Grid marking on one side and a 1/2 Grid marking on the other side. The VIDA App
provides information on which load-adapter grid should be used. With the 1/1 grid (A), the
arrow on the 1/1 side of the load adapter points towards the flying-frame front; with the 1/2
grid (B), the arrow on the 1/2 side of the load adapter points towards the flying-frame front.

User's Manual K&F VIDA L Flying Frame
KLING & FREITAG GMBH © 2017 Version 1.6 Page 15 of 40
A: 1/1 load-adapter grid B: 1/2 load-adapter grid
Tip
Tip for unneeded accessories
An appropriate bay exists for each accessory items such as connector sets or fixing pins.
Whenever an accessory is not in use, lock it in the appropriate bay. Doing so will ensure that
all accessories will be at hand when needed.
5.2.3 Moving the Load Adapter
Warning
Danger! Risk of injury from falling objects!
Improperly mounted speakers are not safe for suspending. Objects falling down impose a
deadly risk for people standing near-by!
In larger arrays of VIDA L or VIDA L with VIDA C some pickpoints may not be used. Please
refer to chapter 'Down-tilt Angle' from page 12.
Be sure to always secure the load adapter using two fixing pins.
The position and grid of the load adapter determine the down-tilt angle of a flying VIDA L
system with or without VIDA C.
Follow the steps below to place the load adapter to the bores identified using the VIDA L
software:
1) Use the VIDA App for simulating
the intended configuration and
determine the required down-tilt
angle.
Double-check, whether you need
to mount the load adapter with
the 1/1-grid or 1/2-grid orientation.
For more information on load
adapters, refer to the Load
Adapters chapter on page 14.
Remove the two lock pins from the
load-adapter base.
2) Change the orientation of the load
adapter as required (1/1 or 1/2
grid), then place it at the previously
identified position.

User's Manual K&F VIDA L Flying Frame
KLING & FREITAG GMBH © 2017 Version 1.6 Page 16 of 40
3)
Warning
To attach and secure the load
adapter, always use both of the
two lock pins supplied.
Never secure the load adapter
using only a single fixing pin!
4) Double-check the load adapter
and, in particular, the two fixing
pins for secure fit.
This completes the preparation stage, meaning that the flying frame can now be mounted to
a VIDA L speaker.

User's Manual K&F VIDA L Flying Frame
KLING & FREITAG GMBH © 2017 Version 1.6 Page 17 of 40
5.2.4 Mounting the flying frame extension
Follow the steps below to mount the VIDA L flying frame extension:
1) Remove the two lock pins securing
the flying frame extension.
2) Insert the flying frame extension
into the bracket provided on the
VIDA L flying frame.
3)
Warning
Never secure the flying frame
extension using only a single
fixing pin!
To attach and secure the flying
frame extension, always use both
of the two fixing pins supplied.
4) Check the fixing pins and the flying
frame extension carefully for secure
fit.
Unmounting the flying frame extension is performed in reverse order.
5.3 Mounting the VIDA L flying frame
Warning
Never use the array if you have any doubt regarding its safety and reliability!
Only qualified event technicians are permitted to suspend a flying frame.
To fly the VIDA L system, you need either a VIDA L flying frame or a VIDA L flying bracket.
Be sure never to fly the system without the use of either a VIDA L flying frame or a VIDA L
flying bracket!

User's Manual K&F VIDA L Flying Frame
KLING & FREITAG GMBH © 2017 Version 1.6 Page 18 of 40
When using a BGV C1 or a D8+ motor, the VIDA L system is intrinsically safe, so no secondary
safety components are required; however, suspending the VIDA L system from a different
motor requires using a secondary safety component. You can attach it to the 3.25 t shackle
with no drop. Refer to VPLT SR 2.0 (“Provision and Use of Electric Chain Hoists”) or similar
locally applicable standards for how to properly implement secondary safety components.
Make sure no persons are standing below the configuration while lifting.
When setting up, double-check each fixing pin for secure fit.
Be sure to use the VIDA App software for verifying the tilt angle for the intended number of
speakers.
The tilt angle calculated by the software must NOT be exceeded.
To prevent injury and damage, be sure to securely place or suspend the speaker array as
specified in the DGUV regulations 17 and 18 or similar locally applicable accident-control
standards.

User's Manual K&F VIDA L Flying Frame
KLING & FREITAG GMBH © 2017 Version 1.6 Page 19 of 40
5.3.1 Attaching a flying frame to a Speaker
Warning
Danger! Risk of injury from falling objects!
Improperly mounted speakers are not safe for suspending. Objects falling down impose a
deadly risk for people standing near-by!
After each step, make sure that all connections between components are secure and all
required components have been mounted.
1) To prepare the speakers for
accepting a VIDA L component,
use the upper lever for moving
out, locking, and securing the
connecting adapters as explained
in the VIDA L speaker Operation
Instructions.
2) To prepare the flying frame:
• Position the load adapter as
calculated by the VIDA App
(1/1 or 1/2 grid—see the Load
Adapter chapter on page 14).
• Mount the load adapter as
calculated by the VIDA App
for the intended down-tilt
angle (see the Moving the
Load Adapter chapter on
page 15).
• Mount the flying frame
extension to the flying frame
(optional: see the Mounting
the flying frame extension
chapter on page 17).
Push the flying frame clips inwards
towards the support until they are
held by the built-in magnets.

User's Manual K&F VIDA L Flying Frame
KLING & FREITAG GMBH © 2017 Version 1.6 Page 20 of 40
3)
Warning
Crushing hazard!
When mounting, avoid crushing
your body parts between system
components moving towards
each other.
During the process, never put
your hands between connecting
faces!
Put the flying frame onto the
speaker.
When doing so, make sure that
the connecting adapters slide in
between the spacer sleeves of the
respective pin bolt—at the front,
the flying bracket must sit flush
with the speaker.
4) Now, press the clip inside the flying
frame outwards to lock and secure
the connecting adapter to the
connecting pin, thus firmly and
securely connecting the flying
frame to the speaker.
5) Make sure that the chamfers of the
4 connecting pins sit flush with the
flying frame surface.