KeeNetic KN-3010 User manual

Quick Start Guide
AC1200 Dual Band Mesh Wi-Fi Gigabit Router/Extender
with Dual Core CPU and a 5-Port Gigabit Smart Switch
Model: KN-3010
Creating a New or Extending
an Existing Network
Keenetic routers deliver reliable, continuous, and secure Wi-Fi throughout your
home. Starting with one main Keenetic router, as your demands increase, you
can add more Keenetic devices to act as Wi-Fi extenders to create a centrally
managed multi-node Mesh Wi-Fi System.
If you are creating a new network and this Keenetic Speedster (hereinafter
‘Keenetic device’) is going to be your Main Router, go to Section A.
If you are extending an existing network and this Keenetic device
is to act as a Wi-Fi extender, go to Section B.
A. Connecting Your Keenetic
Speedster to the Internet
1 Set the physical Operating Mode switch located on the side panel to position
AH— Router Mode.
2 Position your Keenetic device within cable lengths of Ethernet and power
outlets. Place your Keenetic device in an open area for better wireless
coverage. Connect your Keenetic device to a power source. Check that both
the Status LED Cand Wi-Fi LED Dare illuminated and not blinking.
3 Сonnect a mobile device to your Keenetic device via Wi-Fi. The default Wi-Fi
name (SSID) and Wi-Fi password are printed on your Keenetic device’s back
label along with a QR code that will automatically connect your mobile
device to the Keenetic device’s Wi-Fi when scanned. Alternatively, сonnect
a computer to any of the gray Ethernet ports on your Keenetic device
using the included Ethernet cable.
4 Once connected, an Initial Setup Wizard window will appear on your mobile
device / computer. If the Wizard does not appear, using a browser go to
my.keenetic.net and follow the setup instructions.
Note: If the Initial Setup Wizard still doesn’t appear, please refer
to the Frequently Asked Questions section below.
B. Extending Your Existing Network
Coverage
1 On the Keenetic device you wish to be a Mesh Wi-Fi Extender, set the Operating
Mode switch located on the side panel to position IB — Extender Mode.
2 Connect your Keenetic device to a power source. Check that both the
Status LED Cand Wi-Fi LED Dare illuminated and not blinking.
3 Make sure your Keenetic Main Router is active and has an Internet connection.
Connect the 'Extender' Keenetic device to your Keenetic Main Router using an
Ethernet cable (as supplied). Alternatively you can connect Keenetic devices
wirelessly by placing them near to each other and simultaneously pressing the
Wi-Fi buttons Don both devices. Check that the Internet LED Aon the
'Extender' is illuminated.
4 Сonnect a mobile device / computer to your Keenetic Main Router network.
5 Launch a web browser and go to my.keenetic.net and log in to the Main Router
or launch the Keenetic Mobile Application. Then choose the Wi-Fi System
section and click Acquire to add an extender candidate to your Wi-Fi System.
Wait for the process to complete.
6 Disconnect the acquired Extender from the Main Router and place the Extender
where you want in your home to expand your Wi-Fi network. A Keenetic Mesh
Wi-Fi System supports both wireless and wired connections between the Main
Router and Extenders. To maximize your network performance use wired
connections where possible. The Internet LED Aon the Extender will illuminate
when it has connected successfully to your network.
41023
41023
2
2
3
10:00
Mesh Wi-Fi
System
Acquire
4
5
10:00
Welcome to
Your Keenetic
Next
3
4
6
A
1
AB
1
AB
B
For technical support or other information, please visit
help.keenetic.com

41023
FN
AB
What’s in the Box
■1 Router preloaded with KeeneticOS
■1 Level VI energy-efficient 100–240 V power adapter
■1 Ethernet cable
■1 Quick Start Guide (multilingual)
■1 Quick Start Guide (English)
Safety Instructions
■Your Keenetic device is ONLY for indoor use — NEVER use
it outside.
■Before use, remove protective labels from your Keenetic
device, and ensure vents are unblocked.
■Never use your Keenetic device in an enclosed space, and
ensure that the Keenetic-supplied power adapter is always
easily accessible.
■ONLY use a Keenetic-supplied power adapter — cease
to use any damaged adapter IMMEDIATELY.
■Your Keenetic device and its power adapter contain
no user-serviceable parts — DO NOT OPEN.
■Keep your Keenetic device away from water, excessive
humidity or heat, and direct sunlight.
■Your Keenetic device can be safely wall-mounted using
two screws, firmly attached, on any wall surface strong
enough to support 4 times the device’s weight.
Certification Information
Keenetic Limited hereby declares that this device
is in compliance with all relevant provisions of directives
2014/53/EU, 2009/125/EC, and 2011/65/EU. Details of the
original EU declaration may be found at keenetic.com within
details on specific model pages.
This device complies with EU radiation exposure limits set
forth for an uncontrolled environment.
This equipment should be installed and operated with
a minimum distance of 20 cm between the antennas and
a person’s body.
The frequency and the maximum transmitted power for your
device, per the requirements of the EU are listed below:
2400-2483,5 MHz: 20 dBm; 5150-5350 MHz: 23 dBm;
5470-5725 MHz: 30 dBm. This device will support DFS
and TPC functionality while operating in the 5 GHz band.
What should I do if I can’t access
the Initial Setup Wizard page or
the Keenetic Web Interface page?
1. Make sure that your mobile device / computer
is connected to your Keenetic device (in Router
Mode) via Wi-Fi or an Ethernet cable and set
up to obtain an IP address and DNS servers
automatically.
2. Check that you have correctly entered the
appropriate Keenetic device web address: either
my.keenetic.net (recommended)
or 192.168.1.1 or 192.168.2.1.
3. Reboot your mobile device / computer and your
Keenetic device.
4. If the Initial Setup Wizard page is still not
appearing, please follow the instructions below
to reset your Keenetic device.
What should I do if I can’t access the
Internet with my Keenetic device?
1. If the Internet LED Aon the Main Router is not
illuminated, consult your ISP to make sure that
that service is available, and that you are using
the correct connection parameters, e.g. account
login and password, authentication protocol,
MAC address, etc. Make the necessary changes.
2. If the Internet LED Aon the Main Router is
illuminated, please check the wired or Wi-Fi
connections between your Keenetic Main Router
and home devices, including any Keenetic
extenders.
Can I connect a Keenetic Extender
to a Non-Keenetic Main Router?
Absolutely. Press the Wi-Fi button Don your
Keenetic in Extender Mode. Within two minutes
start a WPS session on your Main Router by
pressing the appropriate button on the Non-
Keenetic device. A Keenetic Extender will adopt the
wireless network name and password of the Main
Router. The Internet LED Aon the Extender will
illuminate when it has connected successfully to
your network. To configure the repeater settings,
first open the user interface of the Main Router
to determine the IP address assigned to your
Keenetic Extender. Then, enter that IP address in
the web browser to open the Web Interface on the
Keenetic Extender to make necessary changes.
What should I do if I forget my
wireless password?
The default password for connecting to the Wi-Fi
network can be found on a sticker on the back of
your Keenetic device. If the default Wi-Fi password
has been changed and subsequently lost, the
changed password can be retrieved or reset by
logging in to my.keenetic.net or in the Keenetic
Mobile Application.
What should I do if I forget my
Web Interface page password?
To create a new password, please follow the
instructions to restore the factory settings on your
Keenetic device in the question below.
How do I reset/restore the original
factory settings on my Keenetic
device?
Make sure that your Keenetic device is connected
to a power supply. Press and hold the Reset Button
Buntil the Status LED Cbegins to blink rapidly,
release the Reset Button and wait while your
device restarts.
Important: After restoring factory settings, you
will need to reconfigure your Internet connection
and re-add extenders to your Mesh Wi-Fi System.
LED Lights, Antennas, Buttons and Ports Frequently Asked Questions
1. Wi-Fi Antennas
Four fixed precision printed dipole Wi-Fi antennas
with 5 dBi gain. We recommend keeping the
antennas in a vertical position.
2. Reset Button B
Restores the original factory settings and resets the
administrator password. For instructions on how to
reset your Keenetic device to factory settings, see
the Frequently Asked Questions section below.
3. Network Port 0
The blue port, marked 0, is preconfigured for
Internet connection.
4. Network Ports 1, 2, 3 & 4
By default, these ports are intended for home
devices, but they can be reconfigured and used
to connect to the Internet.
5. DC Power Socket F
For use with the power adapter supplied in the
package. The Keenetic device is designed for
continuous operation and does not need to be
powered off daily.
6. Status LED C
Solid green — Ready for operation.
Blinking green — Rebooting or
updating the operating system.
Rapidly blinking for 2 seconds followed by
continuous illumination — An FN Button
or Wi-Fi Button has been pressed, and the
function assigned to that button has started.
Rapidly blinking for 2 seconds followed by
no illumination — An FN Button or Wi-Fi
Button has been pressed, and the function
assigned to that button was stopped.
Off — Off.
7. Internet LED A
Solid green — Internet connection is established.
Off — No Internet connection.
8. FN LED
By default, it shows that an update for the KeeneticOS
is available The purpose of this LED can be changed
in the settings.
On — An update is available.
Off — No updates available.
9. Wi-Fi LED D
Solid green — Wi-Fi network enabled.
Blinking green — Transferring data.
Blinking slowly — Quick connection
session (WPS) in progress.
Off — Wi-Fi network disabled.
10. Wi-Fi Control Button D
By default, this button allows you to easily add
extenders to the Keenetic Mesh Wi-Fi System, or
other WPS-compliant devices to the wireless network.
Pressing it once — Starts a quick connection
session for adding a new device.
Pressing and holding for 3 seconds —
Turns the Wi-Fi on or off.
You can assign other functions to this button
if necessary.
11. Operating Mode Switch A-B
A — Router Mode (main)
B — Extender Mode
2 3 51 4
6 7 8 9
11
10
This device is restricted to indoor use only when operating
in 5150 to 5350 MHz frequency range (channels 36 - 64).
Per (EC) No 1275/2008, the power consumption
in networked standby if all wired network ports are
connected and all wireless network ports are activated
is 5,3 W
Device Warranty
For the most up to date Warranty Information, please visit
our website keenetic.com/legal.
Your Keenetic device comes with a non-transferable
3-year warranty from the documented date of purchase
(including your 2-year European Limited Warranty). Valid
claims in case of a defect will be honored subject to local
legal requirements.
Disposal
In accordance with European directives, your
Keenetic device, including the power adapter
and cables may not be disposed of with
general household waste. Consult your local
authority or your supplier for information
about disposal.
Notice
When you use your Keenetic device (including when you
connect your Keenetic device the first time), Keenetic
Limited will process certain personal data about you, e.g.,
service tag, serial number, model name, software version,
and IP address of your Keenetic device.
For more information, please go to keenetic.com/legal.
If you are in the European Union / European Economic
Area, Keenetic GmbH will process certain personal data
about you, e.g., service tag, serial number, model name,
software version, and IP address of your Keenetic device.
Please read our Device Privacy Notice for the European
Union / European Economic Area at keenetic.com/legal.
20 mm or longer 67 mm
3.0 mm
1.5~2.0 mm
5.0~6.0 mm