Kenmore C8906 Series User manual

www.sears.ca Sears Canada Inc., Toronto, Ontario M5B 2B8 P/N 137220800A (0905)
Use & Care Guide
Gas & Electric Dryer
Guide d’utilisation et d’entretien
Sécheuse à Gaz ou Électrique
Models/Modèles: C8906 , C8907 , C8917
= color number, numéro de couleur
Printed in U.S.A.

Recognize safety symbols, words and
labels
Safety items throughout this manual are labeled
with a WARNING or CAUTION based on the risk
type as described below:
This symbol alerts you to situ-
ations that may cause serious
body harm, death or property
damage.
This symbol alerts you to situ-
ations that may cause bodily
injury or property damage.
2
Product Registration..............................................................2
Important Safety Instructions ............................................ 2-4
Drying Procedures............................................................. 4-5
Operating Instructions....................................................... 5-8
Features................................................................................8
Dryer Settings Chart..............................................................9
Care and Cleaning..............................................................10
Common Drying Problems ..................................................11
Avoid Service checklist ........................................................12
Warranty ............................................................................13
Notes..................................................................................14
Français ..............................................................................15
Save these instructions for
future reference.
Do not store or use gasoline or other flammable vapors and
liquids in the vicinity of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS:
Do not try to light any appliance.•
Do not touch any electrical switch; do not use any phone in•
your building.
Clear the room, building or area of all occupants.•
Immediately call your gas supplier from a neighbor’s phone.•
Follow the gas supplier’s instructions.
If you cannot reach your gas supplier, call the fire depart-•
ment.
Installation and service must be performed by a qualified
installer, service agency or the gas supplier.
Read all instructions before using this appliance. This book
contains valuable information about:
Operation•
Care•
Service•
Keep it in a safe place.
Read and Save These Instructions
Record Your Model and Serial Numbers
The model and serial numbers of your dryer are found on the
dryer serial plate located of the left side of the door opening.
Record and retain these numbers.
Model Number ____________________________
Serial Number _____________________________
Purchase Date _____________________________
This Use and Care Guide provides general operating instruc-
tions for your dryer. It also contains information about fea-
tures for several other models. Your dryer may not have every
feature included.
Use the dryer only as instructed in this Use & Care Guide and
the Operating Instructions included with your dryer.
For your safety the following information in this
manual must be followed to minimize the risk of fire or explosion or to
prevent property damage, personal injury or death.
Important Safety Instructions
Product Record
Table of Contents
The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of California to publish
a list of substances known to the state to cause cancer, birth defects or other reproductive harm, and requires businesses to
warn customer of potential exposure to such substances. Included in this list are soot and carbon monoxide, both of which
may be produced by the use of this product.

3
Avoid fire hazard or electrical shock. Do not use an adaptor plug or extension cord or remove grounding prong
from electrical power cord. Failure to follow this warning can cause serious injury, fire or death.
Grounding type
Grounding type
10-30R
10-30R
3-wire
3-wire
240 v Electric Dryer
240 v Electric Dryer
120 v Gas Dryer
120 v Gas Dryer
14-30R
14-30R
4-wire
4-wire
(fused 30 amp)
(fused 30 amp)
(fused 30 amp)
(fused 30 amp)
wa
wa
ll receptacl
ll receptacle
Po
Po
wer cord with
wer cord with
3-prong
3-prong
gr
gr
ounded plug
ounded plug
Do not,
Do not,
under
under
an
an
y cir
y cir
cumstances,
cumstances,
cut,
cut,
remo
remo
ve
ve,
or b
or b
ypass th
ypass th
UL-approved service
UL-approved service
cord must be installed
cord must be installed
on electric dryers (not
on electric dryers (not
provided with unit
provided with unit
except those
except those
manufactured for sale
manufactured for sale
in Canada).
in Canada).
e
gr
gr
ounding pr
ounding pr
ong.
ong.
Important Safety Instructions, con’t
PREVENT FIRE
Do not dry items that have been previously cleaned in,•
soaked in, or spotted with gasoline, cleaning solvents,
kerosene, waxes, etc. Do not store these items on or near
the dryer. These substances give off vapors that could ignite
or explode.
Do not place items exposed to cooking oils in your dryer.•
Items contaminated with cooking oils may contribute to a
chemical reaction that could cause a load to catch fire.
Do not dry articles containing rubber, plastic or similar•
materials such as bras, galoshes, bath mats, rugs, bibs,
baby pants, plastic bags and pillows that may melt or burn.
Some rubber materials, when heated, can under certain
circumstances produce fire by spontaneous combustion.
Clean the lint screen before or after each load. The interior•
of the dryer, lint screen housing and exhaust duct should be
cleaned approximately every 18 months by qualified service
personnel. An excessive amount of lint build-up in these
areas could result in inefficient drying and possible fire. See
Care and Cleaning.
Do not operate the dryer if the lint screen is blocked, dam-•
aged or missing. Fire hazard, overheating and damage to
fabrics can occur.
Do not obstruct the flow of ventilating air. Do not stack or•
place laundry or throw rugs against the front or back of the
dryer.
Do not spray any type of aerosol into, on or near dryer at•
any time.
Do not use fabric softeners or products to eliminate static•
unless recommended by the manufacturer of the fabric
softener or product.
To reduce the risk of fire, electrical shock, or injury to persons when using this dryer, comply with the basic
warnings listed below. Failure to comply with these warnings could result in serious personal injuries.
You can be killed or seriously injured if you don’t follow these Important Safety Instructions:
- FIRE HAZARD - A clothes dryer produces
combustible lint. The dryer must be connected to an outdoors
exhaust. Regularly inspect the outdoor exhaust opening and
remove any accumulation of lint around the opening and in
the surrounding area.
Do not continue to use the dryer is you hear squeaking,•
grinding, rubbing or other unusual noises. This could be a
sign of mechanical breakdown and lead to fire or serious
injury. Contact a qualified technician immediately.
Failure to comply with these warnings could result in fire,•
explosion, serious bodily injury and/or damage to the rub-
ber or plastic parts of the dryer.
PROTECT CHILDREN
Do not allow children to play on or in the dryer. Close•
supervision of children is necessary when the dryer is used
near children. As children grow, teach them the proper,
safe use of all appliances.
Destroy the carton, plastic bag and other packing materi-•
als after the dryer is unpacked. Children might use them
for play. Cartons covered with rugs, bedspreads or plastic
sheets can become airtight chambers.
Keep laundry products out of children’s reach. To prevent•
personal injury, observe all warnings on product labels.
Before the dryer is removed from service or discarded, re-•
move the dryer door to prevent accidental entrapment.
Failure to comply with these warnings could result in seri-•
ous personal injuries.
PREVENT INJURY
To prevent shock hazard and assure stability during opera-•
tion, the dryer must be installed and electrically grounded
by a qualified service person in accordance with local
codes. Installation instructions are packed in the dryer for
the installer’s reference. Refer to INSTALLATION INSTRUC-
TIONS for detailed grounding procedures. If the dryer is
moved to a new location, have it checked and reinstalled
by a qualified service person.
To prevent personal injury or damage to the dryer, the•
electrical power cord of a gas dryer must be plugged into a
properly grounded and polarized 3-prong outlet. The third
grounding prong must never be removed. Never ground
the dryer to a gas pipe. Do not use an extension cord or an
adaptor plug.

4
ALWAYS disconnect the dryer from the electrical supply•
before attempting any service or cleaning. Failure to do so
can result in electrical shock or injury.
Do not use any type spray cleanser when cleaning dryer•
interior. Hazardous fumes or electrical shock could occur.
To prevent injury, do not reach into the dryer if the drum is•
moving. Wait until the dryer has stopped completely before
reaching into the drum.
PREVENT INJURY AND DAMAGE TO THE DRYER
All repairs and servicing must be performed by an au-•
thorized servicer unless specifically recommended in this
Owner’s Guide. Use only authorized factory parts.
Do not tamper with controls.•
Do not install or store the dryer where it will be exposed to•
the weather.
Important Safety Instructions, con’t
The instructions appearing in this Use and Care
Guide are not meant to cover every possible condition and
situation that may occur. Common sense and caution must
be practiced when installing, operating and maintaining any
appliance.
A thermal limiter switch automatically turns off the motor•
in the unlikely event of an overheated situation (electric
dryers only). A service technician must replace the thermal
limiter switch after correcting the fault.
Failure to comply with these warnings could result in seri-•
ous personal injuries.
Drying Procedures
1. Prepare load for drying.
Dry items of similar fabric, weight and construction in•
the same load.
Separate dark items from light-colored items. Separate•
items that shed lint from those that attract lint.
Check for stains which may not have been removed in•
washing. Repeat stain removal process and wash again
before drying. Dryer heat may permanently set some
stains.
Place delicate or small items in a mesh bag.•
(Mesh bag not included.)
Clean the lint filter after
every load.
To reduce the risk of fire, electric shock or in-
jury to persons, read the IMPORTANT SAFETY INSTRUCTIONS
in this Use and Care Guide before operating your dryer.
Be sure buckles, buttons and trim are heatproof and•
won’t damage the drum finish. Close zippers; fas-
ten hooks and Velcro®-like fasteners. Tie strings and
sashes to prevent snagging and tangling.
2. Check that the lint filter is clean and in place.
3. Load the dryer and close the door.
Load items loosely. The average wet load will fill the•
drum 1/3 to 1/2 full. Items need room to tumble freely
for even drying and less wrinkling.
If desired, place a dryer fabric softener sheet on top of•
the load at the beginning of the cycle.
To save energy and time and avoid uneven drying and•
wrinkling, do not overload the dryer.
When drying large items, dry only two or three items•
at a time. Fill out the load with small and medium sized
items.
For delicate or very small loads, add two or three simi-•
lar items to improve tumbling action.

To return to factory settings, press the• Pause/Cancel
and Select buttons at the same time and hold until the
signal sounds.
5
Drying Procedures, continued
Clean the lint filter after every load.
To provide the best care for your laundry, not every
setting or option is available with every cycle. If a setting or
option is not available for the cycle selected, the indicator will
not light.
Over-drying can cause wrinkles, shrinkage, lint,
harshness and a build up of static electricity.
Press and hold both for ten seconds
to return to factory settings.
4. Select the appropriate cycle and settings for each
load.
Adjustments to a cycle will be remembered and re-•
called each time that cycle is selected in the future.
5. Start the cycle.
To add or remove items when the dryer is running,•
open the door. The dryer will stop when the door is
opened. Allow the drum to come to a complete stop
before reaching inside.
Close the door and press• Start to resume the cycle.
6. When the cycle ends, remove items immediately
and hang or fold.
Turn the cycle selector knob in either direction to select•
the cycle desired.
A suitable dryness level and options will automatically•
be indicated for the cycle selected. See the “Dryer Set-
tings Chart” for more details.
To change the settings, rotate the• TEMP knob and
press the DRYNESS and OPTIONS buttons to scroll to
the desired settings.
To select or delete an option, press• OPTIONS; then,
while the indicator is blinking, press Select. The indica-
tor will light when the option has been selected. It will
no longer be lighted when the option has been deleted.

6
OPERATING INSTRUCTIONS
Turn the cycle selector in either direction to the cycle desired. To change the cycle once it has begun, press the Pause/
Cancel button twice before selecting a new cycle. Just
turning the cycle selector knob to another selection will not
change the cycle. If the selection is changed after the cycle
starts, the indicator lights will blink, and the signal will beep.
The signal will beep and the status lights will flash, but the
original cycle will continue.
This manual covers many models and not all cycles, options, or features listed are available on
every model. Consoles shown above for reference only. Your model may differ.
Cycle Selection
C8906
C8907
C8917
Follow the fabric care label
instructions on items to be
washed.
For best results
= color number

7
Cycle Selection, continued Cycle Settings
Auto Dry Cycles
Auto Dry cycles take the guesswork out of selecting the
correct drying time for each load. The load will automatically
be dried at the selected temperature to the desired dryness
level. The dryer senses the moisture level of the load as it
tumbles through heated air. Auto Dry cycles save time and
energy and protect fabrics.
When the load has reached the selected dryness level, it will
continue to tumble during a cool down period. This helps
reduce wrinkling and makes items easier to handle during
unloading.
Drying time varies depending on size and dampness of
load and fabric type. If the load is too small or almost dry,
the moisture sensing bars may not detect enough moisture
to continue the cycle and the cycle may end after a few
minutes. If this occurs, select a Timed Dry cycle.
Room temperature and humidity, type of installation and
electrical voltage or gas pressure can also affect drying time.
Towels
Select this Auto Dry cycle for towel loads.
Normal
Select this Auto Dry cycle for cotton items.
Perm Press
Select this Auto Dry cycle to dry cottons and blends with a
no-iron finish.
Delicate
Select this Auto Dry cycle for knits and delicate items.
Timed Dry Cycles
Touch Up
Select Touch Up to help remove wrinkles from clean and
dry items that were not taken from the dryer at the end of
the cycle, have been stored in crowded closets or drawers,
or unpacked from luggage following a trip. It provides
approximately 10 minutes of tumbling followed by a
5-minute cool down period.
Quick
Select this cycle to quickly dry a small load made up of
just a few items. It provides approximately 20 minutes of
tumbling followed by a 10-minute cool down period.
Timed Dry
To manually select the drying time for any load, turn
the knob to a numbered setting. Drying times from 15
to 90 (or 15 to 120) minutes are available in 15-minute
increments. You will not be able to select a cycle or dryness
level. Timed Dry is recommended when using the No
Heat option.
- FIRE HAZARD - To avoid fire hazard, do not
use heat to dry items containing feathers or down, foam rub-
ber, plastics similarly textured, rubber-like materials. Use the
Timed Dry cycle and the Air Fluff/No Heat setting.
Drying Temperature
Turn the TEMP knob until the desired drying temperature is
selected.
High
High is recommended for sturdy fabrics.
Med
Medium is recommended for wrinkle free, permanent press
and lightweight fabrics.
Low
Low is recommended for delicate fabrics.
No Heat
This setting (no heat) should only be used with a Timed
Dry cycle to dry items containing feathers, down, foam
rubber, plastics or rubber-like materials; to refresh clothing,
stuffed animal, pillows or blankets; and to dust draperies.
To change the temperature once the cycle has begun,
press the Pause/Cancel button once, make the new selec-
tion and press Start again.
To change the Dryness level once the cycle has
begun, press the Pause/Cancel button once, make the new
selection and press Start again.
Follow the fabric care label
instructions on items to be
washed.
For best results
Appropriate Dryness level and Options will automatically be
displayed for each cycle. The settings can be changed before
the cycle is started.
If changes are attempted after the cycle starts, the lights will
blink and the signal will beep.
Dryness Level (Auto Dry)
To change the preset level, press the Dryness button to scroll
to the degree of dryness desired.
To protect your fabrics, not all Dryness levels are available
with every cycle. If a Dryness level is not appropriate for the
cycle, it cannot be selected.
The Dryness level selected for the cycle will be remembered
and recalled each time that cycle is selected in the future. To
return to factory settings, press the Pause/Cancel and Select
buttons at the same time and hold until the signal sounds.
Select the Normal dryness level for most Auto Dry cycles.
Occasionally a load may seem too damp or over-dried at the
end of the cycle. To increase drying time for similar loads in
the future, select More Dry. For loads requiring less drying
time, select Less Dry.
Select Damp for items you wish to partially dry before hang-
ing or ironing.

88
Features
END OF CYCLE SIGNAL
A signal will sound at the end of the cycle and periodically
during Wrinkle Rid if selected.
DRYING RACK (some models)
Use the drying rack to dry items which should not be tumble
dried.
Open the dryer door and remove the lint screen.1.
Insert drying rack into the dryer drum. Place the front bar2.
under the lip of the lint screen opening.
Place items to be dried on top of the rack. Weight should3.
not exceed 10 lbs. Leave space between items, but do not
let items hang over the sides or through the grids. Do not
tumble other items when using the drying rack.
Select a4. Timed Dry cycle. Use only the No Heat option for
items containing plastic, foam rubber, rubber-like materials,
feathers or down.
When items are dry, remove the rack and replace the lint5.
screen. If lint screen is not in place, tumbling items could
enter the exhaust system and cause damage to the dryer.
For step-by-step instructions on DOOR REVERSAL, re-
fer to the Installation Instructions supplied with this dryer.
DRUM LIGHT
The drum light will come on whenever the door is opened to
illuminate the drum during loading and unloading. Closing
the door turns off the light.
REVERSIBLE DOOR
Your dryer is equipped with a reversible door. The door can
be hinged on the right or left side.
Place the front bar
under the lip of the lint
screen opening.
Cycle Options
To select or delete the Soft Heat (if equipped), Wrinkle
Rid, or Cycle Signal, press OPTIONS until the blinking light
indicates the desired option. Then, while it is blinking, press
Select. The indicator will light when the option has been se-
lected. It will no longer be lighted when the option has been
removed.
Not all options are available on every model or are compatible
with every cycle. The indicator will not light if the option is
not available with that cycle.
To change the options once the cycle has begun,
press the Pause/Cancel button once, make the new selec-
tion and press Start again.
The options selected for the cycle will be remembered and
recalled each time that cycle is selected in the future. To
return to factory settings, press the Pause/Cancel and Select
buttons at the same time and hold until the signal sounds.
Soft Heat (on select models)
Select the Soft Heat option to protect a load from
excessive heat which can lead to shrinking and over-drying.
The drying temperature will be gradually reduced as the
load dries.
Wrinkle Rid
Select Wrinkle Rid if the dried load might not be removed
promptly at the end of the cycle. The dry load will continue
tumbling without heat for 30 minutes to help reduce
wrinkling. When the Cycle Signal is selected, a beep will
be heard periodically. The load may be removed any time
during Wrinkle Rid.
Cycle Signal
A signal will sound at the end of the cycle and periodically
during Wrinkle Rid if this option is selected.
Control Lock
To avoid having someone accidentally start the dryer, press
OPTIONS and Select at the same time and hold for 10
seconds until the (Control Lock) indicator lights up. To
unlock the controls, press OPTIONS and Select at the same
time and hold 10 seconds until the (Control Lock) indicator
is no longer lit.
Status Lights
The following indicators may be lighted during the cycle:
Drying•
Cool Down•
Wrinkle Rid•
Clean Filter•
• Control Lock

99
Dryer Setting Chart, C8906
These Temperature, Dryness levels and Options are available with the following cycles:
Towels Normal Perm Press Delicate Quick Touch Up Timed Dry
Estimated Cycle Duration** 60 min 55 min 40 min 40 min 20 min 10 min 15-90 min
Temperature
High 9999999
Med 9999999
Low 9999999
No Heat 999
Dryness
More Dry 9*9
Normal 99*9*9
Less Dry 999*
Damp 999
Options
Wrinkle Rid 99*9*999
Cycle Signal 9*9*9*9*9*9*9*
* Factory presets 9Available selections
**Estimated cycle duration is based on default dryness level and factory settings for electric dryers. Displayed cycle
duration may differ slightly on gas models.
= color number
These Temperature, Dryness levels and Options are available with the following cycles:
Towels Normal Perm Press Delicate Quick Touch Up Timed Dry Timed Dry
Estimated Cycle Duration** 60 min 55 min 50 min 40 min 25 min 20 min 15-90 min
(if equipped) 15-120 min (if equipped)
Temperature
High 9999999 9
Med 9999999 9
Low 9999999 9
No Heat 99
Dryness
More Dry 9*9
Normal 99*9*9
Less Dry 999*
Damp 999
Options
Soft Heat 99*9*99
Wrinkle Rid 99*9*99 9 9
Cycle Signal 9*9*9*9*9*9*9*9*
* Factory presets 9Available selections
**Estimated cycle duration is based on default dryness level and factory settings for electric dryers. Displayed cycle
duration may differ slightly on gas models.
Dryer Setting Chart, C8907 , C8917

10
Do not store or place laundry
products on top of dryer at any time. They can
damage the finish or controls.
OUTSIDE
Clean the cabinet with mild soap and water. Never use harsh, gritty or•
abrasive cleansers.
If the cabinet becomes stained, clean with diluted chlorine bleach (1 part•
bleach to 8 parts water). Rinse several times with clear water.
Remove glue residue from tape or labels with a mixture of warm water and•
mild detergent. Or, touch residue with the sticky side of the tape or label.
When cleaning chrome parts use a window cleaner with ammonia or mild•
soap and water.
Before moving the dryer, place a strip of cardboard or thin fiberboard un-•
der the front leveling legs to prevent damage to the floor.
Clean the lint filter after
every load.
Care and Cleaning
Before cleaning the dryer interior, unplug the electrical power cord to avoid•
electrical shock hazards.
Do not use any type spray cleanser when cleaning the dryer interior. Haz-•
ardous fumes or electrical shock could occur.
INSIDE
Clean the lint filter after every load. Lint build-up on the filter restricts air•
flow, which causes longer drying times. The filter is located at the bottom
of the door opening. Remove by pulling straight up. Remove the lint and
replace the filter.
Occasionally a waxy build-up may form on the lint filter and/or moisture•
sensing bars from using dryer-added fabric softener sheets. To remove this
build-up, wash them with warm, soapy water. Dry the filter thoroughly and
replace. Do not operate the dryer without the lint filter in place.
If the dryer drum becomes stained from noncolorfast fabrics, clean the•
drum with a damp cloth and a mild liquid household cleanser. Remove
cleanser residue before drying the next load.
Every 18 months an authorized servicer should clean the dryer cabinet•
interior and exhaust duct. These areas can collect lint and dust over time.
An excessive amount of lint build-up could result in inefficient drying and
possible fire hazard.
To reduce risk of fire or serious injury to persons or property,
comply with the basic warnings listed in the Important Safety Instructions and
those listed below.
- FIRE HAZARD - A clothes
dryer produces combustible lint. The dryer
must be connected to an outdoors exhaust.
Regularly inspect the outdoor exhaust opening
and remove any accumulation of lint around
the opening and in the surrounding area.

11
Common Drying Problems
Many drying problems involve poor cleaning results, poor soil and stain removal, residues of lint and scum, and fabric damage.
For satisfactory drying results, follow these suggestions provided by The Soap and Detergent Association.
PROBLEM POSSIBLE CAUSES SOLUTIONS PREVENTIVE MEASURES
Greasy, oily
stains
Fabric softener sheet.• Rub fabric softener stains with bar•
soap. Rinse and rewash.
Add a few bath towels to small loads for•
proper tumbling.
Some “silk-like” fabrics should be air•
dried.
Use proper drying temperature.•
Place fabric softener sheet on top of load•
before starting the dryer.
Lint Overloading.•
Overdrying causes static•
electricity.
Lint screen not clean when•
cycle began.
Lint is attached to “pills.”•
Reduce load size and rewash using•
liquid fabric softener in the final
rinse.
Or, add a fabric softener sheet and•
tumble without heat.
Use lint brush or roller to remove•
lint.
Do not overload dryer.•
Use fabric softener in washer or dryer to•
reduce static electricity.
Remove items when they are slightly damp•
to avoid overdrying.
Check that lint filter is clean and in place.•
Pilling
(Fibers break off,
ball up and cling
to fabric.)
Overdrying.• Use a lint brush or shaver to re-•
move pills.
Use fabric softener to lubricate fibers.•
When ironing, use spray starch or fabric•
finish on collars and cuffs.
Turn items inside out to reduce abrasion.•
Shrinking Temperature too high.•
Overdrying.•
Irreversible condition.• Follow fabric care label directions.•
If shrinking is a concern, check load often.•
Remove items while slightly damp and•
hang or lay flat to complete drying.
Block knits into shape.•
Wrinkling Overloading.•
Leaving items in dryer after•
cycle ends.
Reduce load size and tumble at•
medium or low heat for 5-10
minutes.
Remove items immediately. Hang•
or fold.
Do not overload dryer.•
Remove items as soon as cycle ends.•

12
Avoid Service Checklist
Before calling for service, review this list. It may save both time and expense. The list includes common occurrences that are
not the result of defective workmanship or materials in this dryer.
OCCURRENCE POSSIBLE CAUSE SOLUTION
Dryer does not start. Electrical power cord is not securely plugged in or plug
may be loose.
Make sure the plug fits tightly in wall outlet.
House fuse blown or circuit breaker tripped. Reset circuit breaker or replace fuse.
Make sure electrical line is not overloaded and the dryer is on a
separate circuit.
Thermal limiter tripped. Call authorized service person for replacement.
Dryer runs but won’t
heat.
There are 2 house fuses in the dryer circuit. If 1 of the 2
fuses is blown, the drum may turn but the heater will not
operate. (electric models)
Replace fuse.
Gas supply valve is not open (gas models). Check to make sure supply valve is open. See INSTALLATION IN-
STRUCTIONS for procedure.
Dryer does not have enough air supply to support the
burner flame (gas models).
See INSTALLATION INSTRUCTIONS.
LP gas supply tank is empty or there has been a utility
interruption of natural gas (gas models).
Refill or replace tank.
Dryer should heat when utility service is restored.
Drying cycle takes too
long, outside of the
dryer feels too hot or
smells hot.
Lint filter is clogged with lint. Make sure all lint has been removed from the dryer lint filter before
starting each cycle.
Exhaust duct requirements have not been met. Exhaust duct must be at least 4 inches in diameter and made of rigid
or semi-rigid metal.
When in place, the duct must have no more than two 90° bends and
must not exceed length listed in INSTALLATION INSTRUCTIONS.
Electric dryer is connected to a 208 volt circuit. Drying time will be 20% longer than drying on a 240 volt circuit.
Drying procedures have not been followed. See “Operating Instructions.”
Outside exhaust hood or exhaust duct may be clogged
or restricted.
Clean out any obstruction.
High humidity. Use a dehumidifier near the dryer.
Excessive wrinkling. Dryer is overloaded. Do not overload. See “Operating Instructions.”
Items left in dryer too long. Remove items as soon as cycle ends.
Insufficient sorting of items. See “Operating Instructions.”
Drying temperature too high. Follow fabric care label instructions.
Scratching or chipping of
the drum finish.
Foreign objects such as coins, pins, clips or buttons are
inside the dryer.*
Always remove foreign objects from pockets before laundering.
Remove objects from drum and restart dryer.
Permanently attached items such as belt buckles, zippers
and fasteners may be hitting the inside of the drum.*
It may be necessary to sew a scrap of material securely around orna-
ments before drying to prevent scratching and damage to the dryer.
*Drum damage caused by foreign objects or permanently attached items is not covered by the warranty.

13
Kenmore Appliance and Optional Pedestal Warranty
IMPORTANT:
Keep a copy of your bill of sale or invoice. The date on the bill establishes
the warranty period should service be required. When appropriate, place the
bill of sale in an envelope and tape it to the back or side of the appliance. If
service is performed, while the appliance is under warranty you may have to
show your bill of sale.
Sears Canada Inc.
222 Jarvis Street
Toronto, Ontario
M5B 2B8
Attention Buyer Dept. 626
Dear Customer,
In manufacturing this product, many steps have been taken to provide
you with the highest quality.
Unfortunately, errors or omissions occasionally occur. In the event that
you find a missing or defective part, please contact your nearest Sears
store.
If you have any suggestions that would help us to improve our assembly/
operation instructions, or this product, please write them down, includ-
ing your name and address, appliance model and serial numbers and
location purchased; mail to:
Protect your appliance even after your warranty expires:
ask about Sears Maintenance Agreement.
Pedestal Warranty
Full One Year Warranty on Mechanical Parts
For one year from date of purchase, when this pedestal is installed with
the listed washer or dryer (see owners manual for specific model) and
operated according to the information in the Use and Care Guide, Operating
Instructions and Installation Instructions, the supplier will replace any of its
mechanical parts if they are defective in workmanship or material. Keep your
bill of sale. The date of the bill establishes the warranty period should parts
be required. This written warranty gives you specific rights. You may also
have other rights which vary from state to state
Warranty Restriction
If the pedestal is used for any other purpose than private family use or used
with any product that requires modification for installation, the warranty is
null and void.
RECORD IN THE SPACE PROVIDED BELOW THE
MODEL NO. AND SERIAL NO. OF THIS APPLIANCE.
MODEL NO:
SERIAL NO:
DATE OF PURCHASE:
RECORD THESE NUMBERS FOR FUTURE REFERENCE.
RECORD IN THE SPACE PROVIDED BELOW THE
MODEL NO. AND SERIAL NO. OF THIS APPLIANCE.
MODEL NO:
SERIAL NO:
DATE OF PURCHASE:
RECORD THESE NUMBERS FOR FUTURE REFERENCE.
One Year Limited Warranty
When installed, operated and maintained according to all
instructions supplied with the product, if this appliance fails due to a
defect in material or workmanship within one year from the date of
purchase, call 1-800-4-MY-HOME® (1-800-469-4663) to arrange for
free repair.
If this appliance is used for other than private family purposes, this
warranty applies for only 90 days from the date of purchase.
This warranty covers only defects in material and
workmanship. Sears will NOT pay for:
Expendable items that can wear out from normal use, including1.
but not limited to filters, belts, light bulbs, and bags.
A service technician to instruct the user in correct product2.
installation, operation or maintenance.
A service technician to clean or maintain this product.3.
Damage to or failure of this product if it is not installed, operated4.
or maintained according to all instructions supplied with the
product.
Damage to or failure of this product resulting from accident,5.
abuse, misuse or use for other than its intended purpose.
Damage to or failure of this product caused by the use of6.
detergents, cleaners, chemicals or utensils other than those
recommended in all instructions supplied with the product.
Damage to or failure of parts or systems resulting from7.
unauthorized modifications made to this product.
Disclaimer of implied warranties; limitation of remedies
Customer’s sole and exclusive remedy under this limited warranty
shall be product repair as provided herein. Implied warranties,
including warranties of merchantability or fitness for a particular
purpose, are limited to one year or the shortest period allowed
by law. Sears shall not be liable for incidental or consequential
damages. Some states and provinces do not allow the exclusion or
limitation of incidental or consequential damages, or limitations on
the duration of implied warranties of merchantability or fitness, so
these exclusions or limitations may not apply to you.
This warranty applies only while this appliance is used in the United
States and Canada.
This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
Sears, Roebuck and Co.
Dept. 817WA, Hoffman Estates, IL 60179
Sears Canada Inc.
Toronto, Ontario, Canada M5B 2B8
Warranty Parts
Warranty parts are available by contacting the supplier where the pedestal
was purchased or refer to the Use and Care Guide that came with the
washer or dryer that is installed on the pedestal for contact information.

14
Notes

www.sears.ca Sears Canada Inc., Toronto, Ontario M5B 2B8 P/N 137220800A (0905)
Use & Care Guide
Gas & Electric Dryer
Guide d’utilisation et d’entretien
Sécheuse à Gaz ou Électrique
Models/Modèles: C8906 , C8907 , C8917
= color number, numéro de couleur
Printed in U.S.A.

Sachez reconnaître les symboles, les aver-
tissements et les étiquettes de sécurité.
Les mesures de sécurité présentées dans ce guide
sont identifiées par le mot AVERTISSEMENT ou
ATTENTION selon le type de risque présenté ci-
dessous:
15
Enregisttrement du produit .................................................15
Consignes de sécurité importantes................................ 15-17
Directives de séchage.................................................... 17-18
Instructions d’utilisation ................................................ 19-21
Caractéristiques ..................................................................21
Tableau de Réglage de la Sécheuse .....................................22
Entretien et nettoyage ........................................................23
Problèmes de séchage courants ..........................................24
Guide de dépannage ..........................................................25
Garantie .............................................................................26
Remarques..........................................................................27
Conservez ces instructions pour
vous y reporter ultérieurement.
Lire ce manuel en entier avant de se servir de cet appareil. Ce
manuel renferme de précieuses informations sur:
le fonctionnement•
l’entretien•
le service après-vente•
Le conserver en lieu sûr
Lire et conserver ces instructions
Noter les numéros de modèle et de série
Les numéros de modèle et de série de la sécheuse se trouvent
sur la plaque signalétique á la gauche de l’ouverture de la
porte. Noter et conserver ces numéros.
N° de modèle ______________________________
N° de série ________________________________
Date de l’achat ____________________________
Le présent Guide de l’utilisateur décrit le mode d’emploi
général de la sécheuse. Il contient également des rensei-
gnements sur les caractéristiques de divers autres modèles.
Les caractéristiques décrites ici peuvent ne pas s’appliquer à
toutes les sécheuses.
N’utiliser la sécheuse que conformément au guide de l’utilisa-
teur et à la Notice de fonctionnement qui l’accompagnent.
Vous ne devez ni entreposer, ni utiliser d’essence ou d’autres
vapeurs ou liquides inflammables à proximité de cet appareil
ou de tout autre appareil électroménager.
QUE FAIRE SI VOUS DÉTECTEZ UNE ODEUR DE GAZ :
Ne mettez pas d’appareil en marche.•
Ne touchez à aucun commutateur électrique; n’utilisez•
aucun téléphone de votre domicile.
Évacuez la pièce, le bâtiment ou la zone touchée.•
En utilisant le téléphone d’un voisin, appelez immédiate-•
ment le fournisseur de gaz. Suivez ses instructions.
Si vous ne pouvez joindre votre fournisseur de gaz, appelez•
les pompiers.
L’installation et l’entretien de cet appareil doivent être réali-
sés par un installateur qualifié, un technicien de service ou le
fournisseur de gaz.
Pour votre sécurité, l’information contenue
dans ces instructions doit être suivie afin de réduire les risques d’in-
cendie ou d’explosion ou pour prévenir les dommages matériels, les
blessures ou la mort.
Consignes de sécurité importantes
Enregistrement du produit
Table des matières
Ce symbole vous
avertit à propos des
situations pouvant
causer des domma-
ges matériels, des
blessures graves ou
même la mort.
Ce symbole vous avertit à
propos des situations pou-
vant causer des dommages
matériels ou des blessures.
En vertu de la loi sur l’eau potable et les produits toxiques « Safe Drinking Water and Toxic Enforcement Act
», la Californie publie une liste des substances chimiques reconnues par l’État comme pouvant causer le cancer ou perturber
les fonctions normales de reproduction. Les fabricants sont tenus d’ajouter des avertissements sur les étiquettes de leurs pro-
duits si ces derniers contiennent l’une ou l’autre des substances chimiques figurant sur la liste. Sont inclus dans cette liste, la
suie et le monoxyde de carbone, deux substances pouvant être produites durant le fonctionnement de cet appareil.

16
Consignes de sécurité importantes (suite)
PRÉVENTION DES INCENDIES
Ne séchez pas d’articles qui ont préalablement été lavés,•
trempés ou éclaboussés avec de l’essence, des solvants, du
kérosène, des huiles de cuisson, de la cire, etc. Ne rangez pas
ces articles sur la sécheuse ou près de celle-ci. Ces substances
dégagent des vapeurs qui pourraient s’enflammer ou exploser.
Ne mettez pas d’articles ayant été exposés à des huiles de•
cuisson dans votre sécheuse. Les articles contaminés avec
des huiles de cuisson peuvent contribuer à une réaction
chimique qui pourrait causer l’inflammation de la charge.
Ne séchez pas d’articles contenant du caoutchouc, du•
plastique ou des matériaux similaires, par exemple des
soutiens-gorge, des galoches, des tapis, des dossards, des
pantalons pour bébé, des sacs de plastique, des oreillers qui
pourraient fondre ou brûler. Dans des conditions particuliè-
res, certains caoutchoucs, lorsqu’ils sont chauffés, peuvent
prendre en feu par combustion spontanée.
Nettoyez le filtre à charpie avant et après chaque utilisation.•
L’intérieur de la sécheuse, le compartiment du filtre à charpie et
le conduit d’évacuation doivent être nettoyés environ tous les
18 mois par un technicien qualifié. Une accumulation excessive
de fibres et de peluches dans ces endroits peut entraîner un
mauvais fonctionnement de la sécheuse et présenter un risque
d’incendie. Reportez-vous à la section Entretien et nettoyage.
N’utilisez pas la sécheuse si le filtre à charpie est bloqué,•
endommagé ou manquant. Cela pourrait provoquer un
risque d’incendie, une surchauffe et les tissus pourraient
être endommagés.
N’obstruez pas le débit d’air de ventilation. Ne placez pas de•
lessive ou de tapis contre l’avant ou l’arrière de la sécheuse.
En tout temps, ne vaporisez aucun type d’aérosol dans, ou•
près de la sécheuse.
Pour réduire les risques d’incendie, de choc électrique, de blessures ou de dommages à la propriété
lors de l’utilisation de cette laveuse, suivez les consignes ci-dessous : Tout défaut de se conformer à ces avertissements pourrait
entraîner de graves blessures.
Vous pouvez être tué ou blessé grièvement si vous ne suivez pas ces instructions de sécurité importantes :
Évitez tout risque d'incendie ou de choc électrique. N’utilisez pas de rallonge électrique ni de
fiche d'adaptation et n’enlevez pas la broche de mise à la terre du cordon d'alimentation. Le
non-respect de cet avertissement peut entraîner des blessures graves, un incendie ou la mort.
Prise murale avec
Prise murale avec
mise à la terre
mise à la terre
10-30R
10-30R
3 ls
3 ls
Sécheuse électrique de 240 V
Sécheuse électrique de 240 V
Sécheuse à gaz de 120 V
Sécheuse à gaz de 120 V
14-30R
14-30R
4 ls
4 ls
(fonctionne avec
(fonctionne avec
des fusibles
des fusibles
de 30 ampères)
de 30 ampères)
(fonctionne avec
(fonctionne avec
des fusibles
des fusibles
de 30 ampères)
de 30 ampères)
Cordon électrique muni
Cordonélectrique muni
d’une che à trois broches
d’uneche à trois broches
avec mise à la terre
avec miseà laterre
Ne coupez pas, n'enlevez
Ne coupez pas, n'enlevez
pas et ne mettez pas hors
pas et ne mettez pas hors
circuit la broche de mise
circuit la broche de mise
à la terre de cette che.
à la terre de cette che.
Un cordon d'alimentation
Un cordon d'alimentation
certié UL doit être
certié UL doit être
installé sur les sécheuses
installé sur les sécheuses
électriques (non inclus,
électriques (non inclus,
sauf pour les modèles
sauf pour les modèles
fabriqués pour être
fabriqués pour être
vendus au Canada).
vendus au Canada).
- RISQUE D’INCENDIE -
La sé-
cheuse produit de la charpie inflammable. La sécheuse doit être
branchée à une évacuation extérieure. Inspectez régulièrement
l’ouverture de l’évacuation extérieure et retirez toute accumula-
tion de charpie près de l’ouverture et de la région avoisinante.
N’utilisez pas de produit assouplissant ou de produit pour éli-•
miner l’électricité statique, à moins qu’il le soit recommandé
par le fabricant du produit assouplissant ou du produit.
Arrêtez la sécheuse si vous entendez un bruit de grincement,•
de frottement ou d’abrasion ou tout autre bruit inhabituel.
Cela pourrait être le signe d’une défectuosité mécanique et
pourrait causer un incendie ou des blessures graves. Com-
muniquez immédiatement avec un technicien qualifié.
Tout défaut de se conformer à ces avertissements pourrait•
entraîner un incendie, de graves blessures ou des domma-
ges aux pièces en plastique et en caoutchouc de l’appareil.
PROTECTION DES ENFANTS
Ne laissez pas les enfants grimper sur la sécheuse ou jouer•
autour de celle-ci. Assurez une supervision attentive lorsque
l’appareil est utilisé près des enfants. Lorsque les enfants
grandissent, enseignez-leur comment utiliser les appareils
électroménagers de façon appropriée et sécuritaire.
Détruisez le carton, les sacs en plastique et tout matériau•
d’emballage externe immédiatement après le déballage de
la sécheuse. Les enfants pourraient les utiliser pour jouer. Le
carton recouvert de tapis, de couvertures ou de feuilles de
plastique peuvent devenir étanches à l’air.
Tenez les produits de lavage hors de la portée des enfants.•
Pour prévenir les blessures, respectez tous les avertisse-
ments des étiquettes des produits.
Avant de mettre la sécheuse hors service ou au rebut, enle-•
vez la porte pour éliminer les risques d’enfermement.
Tout défaut de se conformer à ces avertissements pourrait•
entraîner de graves blessures.
PRÉVENTION DES BLESSURES
Pour éliminer tout risque de choc électrique et assurer le•
bon fonctionnement de l’appareil, la sécheuse doit être ins-
tallée et mise à la terre par un technicien autorisé en vertu
des règlements locaux. Les instructions d’installation sont
situées dans la sécheuse et sont destinées à l’installateur.

Consignes de sécurité importantes (suite)
17
Reportez-vous aux INSTRUCTIONS D’INSTALLATION pour
consulter les procédures de mise à la terre détaillées. Si la
sécheuse est déplacée vers un autre endroit, vous devez la
faire vérifier et réinstaller par un technicien qualifié.
Pour prévenir les blessures ou les dommages à la sécheuse,•
le cordon d’alimentation d’une sécheuse au gaz doit être
branché dans une prise à trois fiches mise à la terre et pola-
risée. La fiche de mise à la terre ne doit jamais être retirée.
N’utilisez jamais un tuyau de gaz pour effectuer la mise à la
terre de la sécheuse. N’utilisez pas de rallonge électrique ni
de fiche d’adaptation.
Débranchez TOUJOURS la sécheuse de l’alimentation élec-•
trique avant de procéder à un entretien ou un nettoyage.
Le non-respect de cette procédure peut causer des déchar-
ges électriques ou des blessures.
N’utilisez pas de nettoyant en vaporisateur lorsque vous•
nettoyez l’intérieur de la sécheuse. Cela pourrait générer
des fumées dangereuses ou des décharges électriques.
Pour éviter tout risque de blessure, ne mettez pas la main à•
l’intérieur de la sécheuse si le tambour est en mouvement.
Attendez que la sécheuse s’arrête complètement avant de
mettre la main dans le tambour.
Directives de Séchage
1. Préparez les articles à sécher.
Faites sécher les articles de tissu, de poids et de fabrication•
similaires ensemble dans la même charge.
Séparez les articles foncés des articles pâles. Séparez les•
articles qui produisent de la charpie de ceux qui attirent
celle-ci.
Vérifiez s’il reste des taches qui n’ont pas été éliminées•
durant le lavage. Répétez le processus d’élimination des
taches et lavez les articles de nouveau avant de les faire
sécher. Il est possible que la sécheuse rende permanente
certaines taches.
Placez les articles délicats ou petits dans un sac-filet.•
(Sac-filet non compris).
Nettoyez le filtre à
charpie après chaque séchage.
Pour réduire les risques d’incendie,
de choc électrique ou de blessure, lisez les MESURES DE SÉ-
CURITÉ IMPORTANTES contenues dans ce guide d’utilisation
et d’entretien avant d’utiliser votre sécheuse.
PRÉVENTION DES BLESSURES ET DES DOMMAGES À LA
SÉCHEUSE
Toutes les réparations et l’entretien doivent être effectués•
par un fournisseur autorisé à moins d’avis contraire dans
ce Guide d’utilisation et d’entretien. Utilisez seulement des
pièces d’origine autorisées.
Ne modifiez pas les commandes.•
N’installez pas ou n’entreposez pas la sécheuse dans un•
endroit où elle sera exposée aux intempéries.
Un limiteur thermique éteint automatiquement le mo-•
teur si une situation peu probable de surchauffe survient
(sécheuses électriques seulement). Un technicien de service
doit remplacer le limiteur thermique une fois la défectuo-
sité corrigée.
Tout défaut de se conformer à ces avertissements pourrait•
entraîner de graves blessures.
Les instructions données dans ce Guide d’uti-
lisation et d’entretien ne sont pas conçues pour couvrir toutes
les éventualités ou situations qui pourraient survenir. Faites
preuve de bon sens et de prudence durant l’installation, l’em-
ploi et l’entretien de tout appareil ménager.
Assurez-vous que les boucles, boutons et garnitures résis-•
tent à la chaleur et qu’ils n’endommageront pas la surface
du tambour. Fermez les fermetures à glissière, les agrafes
et les attaches de type VelcroMD. Attachez les cordes et les
ceintures pour éviter les accrocs et l’emmêlement.
2. S’assurer que le
filtre à charpie est
propre et en place.
3. Mettre les articles dans la sécheuse et fermer la porte.
Mettez les articles dans l’appareil sans le surcharger. Une•
charge mouillée moyenne remplit le tiers ou la moitié du
tambour. Pour assurer un séchage uniforme et éliminer le
plus possible le froissage, les articles doivent disposer d’un
espace suffisant pour culbuter librement.
Si désiré, ajoutez une feuille d’assouplissant au début du•
programme.
Pour économiser de l’énergie et du temps, et pour éviter•
un séchage inégal et la formation de plis, ne surchargez
pas la sécheuse.
Lorsque vous faites sécher des articles volumineux, ne•
mettez que deux ou trois articles en même temps dans la
sécheuse. Remplissez ensuite la sécheuse à l’aide d’articles
de petites ou de moyennes dimensions.
Pour les articles délicats ou de très petites dimensions,•
ajoutez deux ou trois articles semblables pour améliorer le
culbutage.

18
Directives de Séchage (suite)
Pour revenir aux réglages en usine, appuyez sur• Pause/
Cancel (Pause/Annuler) et Select (Sélectionner) en
même temps jusqu’à ce que le signal sonore retentisse.
Le séchage prolongé peut causer le froissage,
le rétrécissement, la formation de charpie, l’accumulation
d’électricité statique et rendre les articles rugueux.
Appuyez sur les deux boutons et maintenez-
les enfoncés pendant dix secondes pour
revenir aux réglages en usine.
4. Sélectionner le programme et les réglages appro-
priés pour chaque charge.
Les modifications apportées à un programme sont mé-•
morisées et les réglages seront utilisés chaque fois que
ce programme sera sélectionné à l’avenir.
5. Commencez le programme.
Pour ajouter ou retirer des articles pendant que la sé-•
cheuse fonctionne, ouvrir la porte. Le sécheuse s’arrête
lorsque la porte est ouverte. Attendre que le tambour ait
complètement cessé de tourner avant de mettre la main à
l’intérieur.
Fermer la porte et appuyer sur• START pour remettre la
sécheuse en marche.
6. À la fin du cycle, retirer immédiatement les vêt
ments et les suspendre ou les plier.
Tournez le sélecteur de programme dans un sens ou•
dans l’autre pour choisir le programme désiré.
Une niveau de déshumidification et les options s’af-•
fichent automatiquement pour chaque cycle. Voir le
Tableau de réglage de sécheuse pour obtenir de plus
amples détails.
Pour modifier les réglages, tournez le bouton• TEMP
(Température), et appuyez sur les touches DRYNESS
(Niveau de séchage) et OPTIONS pour faire défiler la
liste aux réglages désirés..
Pour sélectionner ou annuler une option, appuyez•
sur OPTIONS. Ensuite, alors que l’indicateur clignote,
appuyez sur Select (Sélectionner). L’indicateur s’allume
lorsque l’option est sélectionnée. Il s’éteint lorsque
l’option est annulée.
Afin d’assurer un lavage adéquat de vos articles,
les réglages et les options ne sont pas tous disponibles pour
chaque programme. Si un réglage ou une option ne convient pas
au programme sélectionné, le voyant ne s’allume pas.
Nettoyez le filtre à charpie après chaque
séchage.

19
C8906
C8907
C8917
INSTRUCTIONS D’UTILISATION
Sélection d’un Programme
Suivez les instructions sur
les étiquettes des articles
à laver.
Pour de meilleurs résultats
Tournez le sélecteur de programme dans un sens ou dans
l’autre vers le programme désiré.
Pour changer de programme lorsque la sécheuse est en
marche, appuyez sur Pause/Cancel (Pause/Annuler) de
pression deux avant de sélectionner un nouveau programme.
Si vous modifiez simplement la sélection avec le bouton du
sélecteur de programme, le programme ne changera pas.
Si la sélection est modifiée après le démarrage du cycle, les
indicateurs lumineux clignotent et le signal sonore retentit. Le
signal sonore retentit et les lumières d’état clignotent, mais la
sélection originale se poursuit.
= numéro de couleur
Ce manuel couvre plusieurs modèles et certaines options, cycles ou caractéristiques décrites ne sont pas disponibles sur des modèles particuliers. La
console montrée ci-haut est fournie à titre de référence seulement et votre modèle pourrait être différent.