Kenmore 721.67600 User manual

SEARS Installation Instructions
®
1.3 Cu. ft /900W(IEC 705 Rating Standard)
MICROWAVE OVEN
Model No.
721.67600
721.67601
721.67602
721.67680
721.67681
721.67682
m]_l / ___ _l j _
CAUTION: Read and save these installation instructions.
Sears, Roebuck and Co., Hoffman Estates, IL. 60179 U.S.A.

YOUR SAFETY FIRST
BEFORE YOU START
•Proper installation is the installer's responsibility!
- Read the entire manual before you begin. The Model number label is located on the oven front.
See Figure 1. Mounting plate is located on back side of microwave oven. See Figure 2.
BE SURE TO READ THE FOLLOWING SAFETY INSTRUCTIONS:
I
Model Number Label
Figure 1
Mounting
plate
Back of oven
Figure 2
WARNING
FOR YOUR SAFETY:
• You will need TWO people to install this oven. It is heavy and could cause personal injury if not handled
properly. The dimensions of the oven are as follows:
MODEL NO : 721.67600, 721.67601,721.67602, 721.67680, 721.67681,721.67682
Height :16 7/16inches
Width : 29 16/16inches
Depth : 15 3/8 inches
Weight : 58 pounds
•Avoid Electrical Shock!
- Before you drill into the wall, note where electrical outlets are and where electrical wires might be behind
concealed the wall, YOU COULD GET AN ELECTRIC SHOCK it you contact electrical wires with your
drill bit.
- Locate and disconnect the power of any electrical circuits that could be affected by installing this oven.
IF YOU DO NOT DISCONNECT THE POWER, YOU COULD GET AN ELECTRIC SHOCK.
•ELECTRICAL RATING OF THIS OVEN : 120V AC. 60 Hz.
11.9 Amps /1350 Watts (Microwave oven only)
12.9 Amps /1500 Watts (Microwave oven + Cooktop Lamps + Ventilation Fan)
- You need a 120volt, 60Hz, AC only, 15 or 20ampere, fused electrical supply (located in the cabinet
above the microwave as close as possible to the microwave circuit) serving only the microwave.

YOUR SAFETY FIRST
• THIS APPLIANCE MUST BE GROUNDED!
- Ifthere is an electrical short circuit, grounding reduces the risk of electrical shock by providing an escape
wire for the electric current. This appliance is equipped with a cord having a grounding wire with a
grounding plug.
• Place the plug into a properly installed and grounded outlet. See Figure 3.
• Do not use an extension cord. PROPERLY POLARIZED AND
• Keep the power cord dry and do not pinch or crush it. GROUNDED OUTLET
DO NOT, UNDER ANY CIRCUMSTANCES, REMOVE THE __
POWER SUPPLY CORD GROUNDING PRONG!
This appliance MUST be grounded?
Three-Pronged (Grounding) plug
Figure 3
_, WARNING _,
If you use the grounding plug improperly, you risk electric shock!
- Check with a qualified electrician if you are not sure whether the oven is properly grounded or if you do
not completely understand the grounding instructions.
DO NOT USE A FUSE IN THE NEUTRAL OR GROUNDING CIRCUIT.
WARNING
Improper grounding could result in electric shock or other personal injury.
SAVE THESE INSTRUCTIONS FOR THE LOCAL ELECTRICAL INSPECTOR'S USE.
• DO NOT EXPOSE YOURSELF TO EXCESSIVE MICROWAVE ENERGY?
- DO NOT try to operate the microwave oven with the door open.
- DO NOT tamper with or defeat the safety interlocks.
- DO NOT place objects between the microwave oven front face and the door.
- DO NOT allow soil or cleaner residue to build up on the flat surfaces around the microwave oven door.
- DO NOT operate the microwave oven if it is damaged.
- The microwave oven door must close properly to operate safely.
- DO NOT USE THE MICROWAVE OVEN:
• If the door is bent.
• If the hinges or latches are broken or loose.
• If the door seals, sealing surfaces or glass is broken.
- DO NOT ATTEMPT TO ADJUST OR REPAIR THE OVEN YOURSELF?
It should be adjusted and repaired by a qualified technician who can check for microwave leakage
after repairing the oven.
WARNING
If you do not use the microwave oven as instructed, you could
be exposed to excessive microwave energy.

YOUR SAFETY FIRST
•MAKE SURE YOU HAVE ENOUGH SPACE AND SUPPORT.
- Mount the oven against a flat, vertical wall, so that it is supported by the wall. The wall should be
constructed of minimum 2" x 4" wood studding and 3/8" thick drywall or plaster/lath.
- ATTACH AT LEAST ONE of the two lag screws supporting the oven to a vertical, 2" x 4" wall stud.
- DO NOT mount the microwave oven to an island or peninsula cabinet.
- BE SURE the upper cabinet and rear wall structures are able to support 150 Ibs., plus the weight of any
items you place inside the oven or upper cabinet.
- Locate the oven away from strong draft areas, such as windows, doors, and strong heating vents.
- BE SURE you have enough space. See Figure 4 below for minimum vertical and horizontal clearance.
WARNING
If you do not mount the oven as instructed,
you risk personal injury and/or property damage.
ii Grounded Plug
_-b i,,,, i (inside upper cabinet)
Power St I ply Cord Hole
)
30"min.cabinetopeningwidth
30"min. clearancefrom bottom
of cabinetto cooking surface
orcountertop
(Use templates included
with installation
instructions)
[........................................................................................................................................................................................................................................
Figure 4
CAUTION
• Before you begin installing the oven, PLACE A
PIECE OF THE CARTON OR OTHER HEAVY
MATERIAL (a blanket) over the countertop or
cooktop to protect it. Do not use a plastic cover.
Failure to protect these surfaces could result in
property damage.

PARTS, TOOLS, MATERIALS
THE FOLLOWING PARTS ARE SUPPLIED WITH THE OVEN:
NOTE: Depending on your ventilation requirements, you may not use all of these parts.
Damper/duct connector
(for roof-venting or wall-venting installation)
Not Actual Size
One powercord clamp and
Onedark-colored mounting screw
(to hold the power cord)
Actual Size
Two tapping screws - Actual Size
(for attaching the damper duct connector) One lock pin and one washer-Not Actual size
One power cord clamp bushing - Actual Size
(for the cord hole in a metal upper cabinet)
Four 1/4" x 2" lag screws - Actual Size
(for wall stud holes) Four 1/4" x 3" toggle bolts - Actual Size
(for drywall holes)
Four 1/4" x 2" bolts - Actual Size
(for securing to the upper cabinet)
Two washers - Actual Size
(for the two upper cabinet bolts)
Four spring toggle heads - Actual Size
(for the toggle bolts)
NOTE: You need to install at least one lag screw into a 2" x 4" stud and four anchor bolts into the wall and
the mounting area must meet the 150 Ibs. weight requirement.