Kenmore Elite 79048883112 User manual

Convection Microwave Oven Installation Instructions
& WARNING
Installation and service must be performed by a qualified installer.
IMPORTANT: Save for local electrical inspector's use.
Read and Save these instructions for future reference.
The electrical requirements for this oven are 120 volts, 15 amps.
NOTE
1. Base must be capable of supporting 150 pounds (68.0 kg)
for the Convection Microwave Oven only.
Make sure base is level and front of cabinet is square. If
the cabinet base is not level, the oven will tend to slide out
when opening the door.
Minimum required distance is 36" (91.44 cm) from the
floor.
The outlet should not be located in the shaded area of
Figure 1. It is required the outlet be a dedicated 120 volts
with a lSamp rating for the appliance.
Minimum required distance between the Microwave Oven
and the wall oven cutouts should be at least 3 inches. The
actual visible space will be reduced due to the overlap of
the Microwave Oven lower vent and the wall oven.
Product Dimensions
Model A B Cc D
27" (68.8) 27" (68.8) 2193/4" (55.3) 247/_" (63.2) 203," (52.6)
30" (76.4) 30" (76.4) 2134" (55.3) 28" (71.1) 2034." (52.6)
Cutout dimensions and cabinet width
Medel Min. F Max. G Min. H Max. I
27" (68.8) 25 Ve" (63.8) 255" (65.1) 24" (61.0) min. 21" (53) 212" (54.6) 27" (68.8) min.
30" (76.4) 282" (72.4) 29" (73.7) 24" (61.0) min. 21" (53) 212" (54.6) 30" (76.5) min.
All dimensions are in inches (cm).
P/N 316902472
TINSEB527MRRO
c

Convection Microwave Oven Installation Instructions
IMPORTANT
NOTES
TO
THE
INSTALLER
IMPORTANT
SAFETY
1.
Read
all
instructions
contained
in
these
installation
INSTRUCTIONS
instructions before installing the Convection Microwave
Oven. This oven can be built into a cabinet or wall
. . . A CAUTION
by itself or above any electric wall oven or warming
drawer. Never use your appliance for warming or heating the room.
. . . Prol d f th ithout ad t tilati
2. Remove all packing material from inside the oven rolonged’ use oF me oven WInour adequare venilanon can
be dangerous.
cavity before connecting the electrical supply to the
Convection Microwave Oven. DO NOT REMOVE THE
WAVEGUIDE COVER, which is located on the cavity
ceiling. See Figure 2A. CARPENTRY
Refer to Figure 1 for the dimensions required for your
appliance, and the space necessary to install the oven. The
oven support surface should be solid plywood or similar
Waveguide Cover
6 I material, the surface must be level from side to side and
ven Cavity ~|
from front to rear.
Door Seals
and Sealing
Surfaces ELECTRICAL REQUIREMENTS
Hinge
safety |) : The appliance operates on a 120 volt, 60 Hz electrical
Door Latch —— supply with a separate ground wire. Provide a separate
circuit with a fuse or circuit breaker rated for 15 amps.
Figure 2A Figure 2B Observe all governing codes and local ordinances
3. Remove the 2 shipping duct supports (see Figure 2B) by A CAUTION
removing the 2 screws securing each side. Reinsert 2 .
screws (each side) to secure the stainless cover. To prevent damage to the oven control, during cold
temperature weather, wait at least three (3) hours
4. Remove the feature sticker, if there is one, from the after receiving this oven before supplying power to the
outside of the door. appliance. This will prevent possible damage to the built-in
5. Check the oven for any damage, such as misaligned or oven control at power on.
bent door, damaged door seals and sealling surfaces,
broken or loose door hinges and latches and dent inside
the
cavity
or
on
the
door.
CABINET
INSTALLATION
A
WARNING
A
WARNING
° The Convection Microwave Oven can tip when the door is
If there is any damage, do not operate the oven and
contact your dealer or KENMORE AUTHORIZED SERVICER. Pe? The Anti-Tip brackets supplied with the Convection
Microwave Oven must be attached to the cabinet and
6. Observe all governing codes and local ordinances. the appliance to prevent tipping of the unit and injury to
persons.
7. Be sure to leave these instructions with the consumer.
IMPORTANT NOTE TO THE CONSUMER ANTI-TIP BRACKETS INSTALLATION INSTRUCTIONS
. . . ' . Unpack the Convection Microwave Oven and find the
Keep these instructions with your Owners Guide for future ae : : .
2 Anti-Tip brackets and screws included in the literature
reference.
package.
2. Install the Anti-Tip bracket in the cabinet as shown
on Figure 3. Note: To prevent damage to cabinet, it is
recommended to drill Yc" (0.16 cm) diameter pilot holes
before installing the Anti-Tip brackets.
se bho

Convection Microwave Oven Installation Instructions
CONVECTION MICROWAVE OVEN INSTALLATION ANTIcTIP BRACKET INSTALLATION
A
CAUTION
Cutout
Width
(See
dimensions
below)
Two persons are required to install the oven. Never hold the
door
handle
when
moving
the
oven.
tH
re
Anti-Tip Brackets”
Cutout Height
21" (53.3 cm) Min.*
21-1/2" (54.6 cm) Max.*
3. Place the oven adjacent to the opening on a table or
stand. Plug the power supply cord into the electrical 16-1/2"
outlet. Carefully guide the oven into the prepared (41.9 cm)
opening. Avoid pinching cord between oven and
wall. See Figure 4. Push the unit in and against the
cabinet. The oven side bracket will clip into the Anti-Tip
brackets. See Figure 3. Figure 3
4. To pull out the oven for servicing, open the door and
locate the two holes on the side frame. Simultaneously
insert the tools provided with the appliance in both
holes and pull the oven towards you. See Figure 5.
27-INCH Cutout Width
25 Va" (63.8 cm) Min.*
25 54" (65.1 em) Max.®
25 34" (64.5 cm) Recommended*
30-INCH Cutout Width
28 V2" (72.4 cm) Min.*
29" (73.7 em) Max.*
28 34" (73.0 cm) Recommended*
FINISHED ANTI-TIP BRACKET INSTALLATION REMOVING OVEN FOR SERVICING
Anti-Tip Bracket
installed in cabinet Oven removed
er~ from the cabinet
Cabinet
aninet Anti-Tip
Bracket
released
Right Side
Tool supplied
Figure 4 Figure 5

Convection Microwave Oven Installation Instructions
MODEL AND SERIAL NUMBER LOCATION
The serial plate is located on the oven front frame. See
Figure 6.
When ordering parts for or making inquires about your
oven, always be sure to include the model and serial
numbers and a lot number or letter from the serial plate on
your oven.
PRODUCT IDENTIFICATION
Menu
Label
Figure 6
BEFORE YOU CALL FOR SERVICE
Read the Before You Call for Service Checklist and
operating instructions in your USE AND CARE GUIDE.
It may save you time and expense. The list includes
common occurrences that are not the result of defective
workmanship or materials in this appliance.
Refer to the warranty in your USE AND CARE GUIDE for
our service phone number and address. Please call or write
if you have inquiries about your product and/or need to
order parts.