Kenmore 272.98300.491 User manual

SEWRNG
MACHINE
CABINET
OWNER'S MANUAL
Model Number 272.98300.491 Oak
272.98301.491 White
272.98302.49_ Cherry
ASSEMBLY
PARTS LIST
IMPORTANT:
Read instructions before assembling.
98300-FC
98301-FC
98302-FC

(20) #8xl/2" Panhead Screws
(2) #6x5/8" Panhead Screws
Hardware Included (1) Right Wing (1) Left Wing
(25) Cams_ _ _
(6) #5x5/8" Flathead _l
_j-_Screws _
(1) 2 pc, Knob
(8) 5ram Hex Bolt Rubber Tab
!
(2) Mounting Bolts ('r(/("f I--
3-Small
1-Large
(2) Wing Nuts
(2) Zinc Flat Washers
(5) Caster Clips
(5) Caster Insert
(2) Bronze Strike Washers
(4) Drawer Backs _
"_ White Plastic
98301 only
(8) Drawer Sides
_o (2) Round Magnet
@
(25) Connecting Bolts (4) Metal Handle 98300
98302
(8) #8132x314"
Handle Bolts
Page 2
Allen Key
(1) Strike Plate
hanism
98300-2
98301-2
98302-2

UnderstandingHowthe"ARR0W-LOC"CamFastenerWorks.
ARROW
TOWARDS
HOLEIN
EDGE
1. Position bolt in 2. Press cam into 3. Insert bolt through
pre-drilled hole and pre-drilled hole until pre-drilled hole in
turn until tight, flush with surface, edge of panel.
4. To lock, rotate cam
until tight, using
allen key provided.
Cabinet Assembly
Step 1. Place Top, Partition and Left and Right Sides on a flat protected surface (to prevent
scratching of parts) and thread connecting bolts (25 total) into pre-drilled holes (as shown in
FIG. 1), Turn Partition over and thread in the remaining bolts as indicated below (FIG. 1A).
¢
Right Leaf
lNOTE: !
•= Connecting Bolt
Top Assembly
Left Leaf
FIG. 1
Right Side Panel
FIG. 1A
el
Left Side Panel
••• • 0°
J J
Partition Partition
(viewed form right) (viewed form left)
Page 3
98300-3
98301-3
98302-3

CabinetAssemblyContinued:
Step2• InstallCams(25total)intotheholesprovidedinthecabinetpartsshownbelow,pushinga
camintoeachholeuntilflush withthe surface•Thearrowon theCamsshouldbeturned(using
aregularscrewdriverorAllenKeyProvided)to facetheholein eachedgewheretheConnecting
Boltswill enter•
Step2A•Weareproviding(1)whiteplastichookto beused,tostoreyourcustomfit sewingheadinsert,
(Sears#9801) to be mounted on the inside left side panel in Hole (A) or (B). CAUTION Do not
attach hook until you know the cutout size of your insert. Use Hole (A) for cutout 3" or less & (B)
for cutout larger than 3". NOTE:
= Cam
/Back Left Side Panel
o/
°• ° • i •
Right Side Panel
•°
o
•°o
0!
Partition
(viewed from right) Compartment
Back
Right Left
Leaf Supports
°y
Front
Shelf
Page 4
Oi
Compartment
Bottom 98300-4 98301-4
98302-4

Step 3. Attach the Magnet to the Partition by using (2) #6x5/8" Screws. Be sure to keep the magnet
Strikes (metal) lacing towards the front edge ot the Partition (as shown in FiG. 2.)
(_ /_] (2) #6x5/8" Screws
/uo !
Partition
(viewed from left)
Step 4, Next, attach the plastic Drawer Runners by using (32) #6x1" Flathead Screws (as shown in FIG. 4).
DO NOT OVER TIGHTEN.
I
®
•.)
(• • )
C • • )
FIG. 4
6x1" Flathead Screws
@/i
It
Drawer Runners /
( • • • ,,• )
(• • • .I
Partition
(viewed from right)
Page 5
Right Side
98300-5
98301-5
98302-5

Step 5. Attach the Left and Right Wings to the Platform using (4) #8xl/2" Panhead Screws (as shown in
FIG. 5). The long flanges facing outward and toward edge of Platform.
#8x1/2" Panhead Screws
FIG. 5
0
o o o
Step 6.
Platform
Attach the Wings (with Platform) to the Carriage of the Lift Mechanism by laying the Back (with
Lift attached) in a flat position and aligning the top and bottom holes in Wing flanges with the
holes in the Lift Carriage. Insert the (8) 6mm Hex Head Bolts through the Wings and Carriage
and attach aWasher & Hex Nut to each Bolt (as shown in FIG. 6). Before tightening the Nuts and
Bolts using a 10mm wrench or adjustable wrench or pliers, use a square or the bottom shelf of
cabinet to square the platform with the back (as shown in FIG. 6B). Final assembly should
look like FIG. 6A.
FIG. 6A FIG. 6
!
This -_
or _P
This
i
@ @
® @
_ r-'*l I I'
FIG. 6B
.ex. a u*\Wis;er:
i
L_
IMachine Platform
L,eft Wing
\
6mm x11mm Hex Head
Page 6
Lift Carriage
98300-6
98301-6
98302-6

Step 7. Attach the (4) plastic Trays to the Door by inserting the (16) #8xl/2" Panhead Screws into the
Door. The (3) smaller trays are mounted in the three top rows of predrilled holes, with larger
tray mounted in bottom row. Attach Magnet Strike Plate with (1) #5xl/2" Flathead Screw.
Attach (2) door hinges to Door with (6) #5xl/2" Screws (as shown in FIGS. 7 AND 7A).
Long end attaches to door.
#8x1/2" Panhead Screw
#5x1/2" Flathead Screw
Step 8.
Step 8Ao
Door
Attach (4) Support Hinges to Left and Right Supports with (8) #8x5/8" Flathead Screws; insert (2)
Round Magnets into holes in Leaf Supports (as shown in FIG. 8).
Attach Self-Sticking rubber tabs to outer edge of each leaf support.
Self-Sticking
d_ Rubber Tab
_// t_ightLeafSupport (//1
Round Magnet \] ] ,_ #8x5/8 t
I I _l FlatheadScrew _,
FIG. 8 Self-Sticking
Rubber Tab
Page 7
Left Leaf Support
Round Magnet
98300°;
98301-7
98302°7

Step 9. Place or tap Caster Clips, Inserts, (1) Locking Caster, and (1) Non-Locking Caster into Left Side (as
shown in FIG. 9 below). Attach the back to Left Side by guiding Back onto Connecting Bolts in
Left Side (as shown in FIG. 9), turn Cams to the Locked Position. Attach the Shelf and Front by
guiding each piece onto the appropriate Bolts in the side, and turn the Cams to the Locked Position.
FIG. 9
Front
®
1
!
II
Taped
Edge-_
1
| o .
@
Back
Left Side
col
@
I II } FIG, 9A
I il
'i CasterC,p.on-Locki°gCaste
,
/Caster Insert
//
// / Caster Chp____ L°cking Caster
_- -"_'---_Ca_t-_e_Inse.
Page 8
98300-E
98301-8
98302-8

Step 10. Place or tap Caster Clip, Insert and Non-Locking Caster into the Partition (as shown in Fig. 10. below
Align the Connecting Bolts in Partition with corresponding holes in Front, Shelf and Back.
Now, making sure the Partition is completely on the Connecting Bolts, turn Cams to Locked
Position.
FIG. 10
._Non-Locking Caster
-- -- "_Caste-_r Insert
Page 9
98300-4
98301-9
98302-9

Step11. AttachCompartmentBottomandCompartmentBackto Partitionbyguidingeachpieceonto
ConnectingBoltsin the Partition(asshownin FIG.11).TurnCamsto LockedPosition.
FIG.11 Compartment
Bottom
Taped I
I
1
Page lO
98300-1(
98301-10
98302-10