Kenwood DPC-981 User manual

KENWOOD
DPC-981
DPC-782
DPC-781 _
PORTABLE COMPACT DISC PLAYER
INSTRUCTION MANUAL
KENWOOD CORPORATION
Note:
This instruction manual is for common use with the three models above.
Unpacking
Unpack the unit carefully and make sure that all accessories are put aside
so they will not be lost.
Examine the unit for any possibility of shipping damage. If your unit is
damaged or fails to operate, notify your dealer immediately. If your unit was
shipped to you directly, notify the shipping company without delay. Only the
consignee (the person or company receiving the unit) can file a claim against
the carrier for shipping damage.
We recommend that you retain the original carton and packing materials for
use should you transport or ship the unit in the future.
Before using the rechargeable batteries
The rechargeable batteries come non-charged condition. Read "Recharg¬
ing the batteries" carefully and charge the batteries before use.
_n COMPACT
qIdsis
DIGITAL AUDIO
B60-3427-00(35)(K,P)
98/12 11 10 987654321 97/12 11 10 9 8

A\ Caution : Read this section carefully to ensure safe operation.
Units are designed for operation as follows.
U.S.A. and Canada . A C 120 V only

DPC-98V782/781 (En/K)
A Caution: Read this page carefully to ensure safe operation.
WARNING : TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
IMPORTANT SAFEGUARDS
Please read all of the safety and operating instructions before operating this unit. For best results, follow all warnings placed on the unit and adhere to the operating and use
instructions. These safety and operating instructions should be retained for future reference.
1. Power sources — The unit should be connected to a power supply only of the type
described in the operating instructions or as nnarked on the appliance.
2. Power-cord protection — Power-supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or against them, pay particular
attention to cords at plugs, convenience receptacles, and the point where they exit from
the unit.
3. Enclosure removal — Never remove the enclosure. If the internal parts are touched
accidentally, a serious electric shock might occur.
4. Drop — Do not drop the unit or apply strong shock to it. (Damage due to dropping the
unit is not covered by the warranty.)
5. Ventilation — Avoid hindering the ventilation of the unit by covering it with a cloth, etc.
6. Abnormal smell — If an abnormal smell or smoke is detected, immediately turn the
power OFF and pull out the power cord. Contact your dealer or nearest service center.
7. Heat — Avoid placing the unit under direct sunlight or near a source of heat such as
heating equipment. Particularly, never leave it in an automobile or on the dashboard.
8. Temperature — The unit may not function properly if used at extremely low, or freezing
temperatures. The ideal ambient temperature is above +5°C (41 °F).
9. Water and moisture — The unit should not be used near water — for example, near a
bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming
pool, etc.
10. Dust and moisture — Avoid places where is dusty or where the humidity is high.
11. Vibrations — Avoid placing the unit on an unstable place such as a shelf or in a place
subject to vibrations.
12. Magnetic fields — Keep the unit away from sources of magnetic fields such as TV sets,
speaker systems, radios, motorized toys or magnetized objects.
13. Cleaning — Do not use volatile solvents such as alcohol, paint thinner, gasoline, or
benzine, etc. to clean the cabinet. Use a clean dry cloth.
14. Nonuse periods — The power cord of the unit should be unplugged from the outlet when
left unused for a long period of time.
15. Damage requiring service — The unit should be serviced by qualified service personnel
when;
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the unit.
C. The unit has been exposed to rain.
D. The unit does not appear to operate normally or exhibits a marked change in
performance.
E. The unit has been dropped, or the enclosure damaged.
16. Servicing — The user should not attempt to service the unit beyond that described in the
operating instructions. All other servicing should be referred to qualified service personnel.
17. CAUTION — TO PREVENT ELECTRIC SHOCK DO NOT USE THE AC PLUG WITH AN
EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE
FULLY INSERTED TO PREVENT BLADE EXPOSURE.
Notes on using through car stereo
• In case of abnormality such as smoke production, immediately unplug the car battery adaptor from
the cigar lighter socket.
• Do not leave the products or batteries n the car, particularly above the dashboard, for this may lead
to malfunction or damage due to solar heat.
• If the unit is connected to a car stereo using an audio cord, noise may sometimes interfere.
In case of abnormality, immediately press the open key to turn the power OFF, and unplug the
AC adaptor from the power outlet. Then please contact your nearest KENWOOD service
center.

For rechargeable battery
WARNING
• Use specified charger only.
• Do not disassemble or mutilate, may cause burns.
• Do not incinerate or heat, may cause burns, burst or release toxic materials.
• Do not short circuit, may cause burns.
• Keep away from children.
The marking of products using lasers (Except for some areas).
This label is attached to the bottom panel and says that the component
CLASS 1 I uses laser beams that have been classified as Class 1. It means that the unit
LASER PRODUCT I is utilizing laser beams that are of a weaker class. There is no danger of
hazardous radiation outside the unit.
FortheU.S.A.
KENWOOD CORPORATION
2967-3, ISHIKAWA-CHO,
- -
CAUTION:
HACHIOJI-SHI,
Use of controls or adjustments or performance of proce- ,
dures other than those specified herein may result in
TOKYO, JAPAN
hazardous radiat on exposure.
In compliance with Federal Regulations, following are
^ ^
KENWOOD CORP. CERTIFIES THIS EQUIPMENT
CONFORMS TO DHHS REGULATIONS NO 21
reproductions of labels on, or inside the product relating '
CFR 1040.10, CHAPTER 1, SUBCHAPTER J.
to laser product safety. '
k_^___J
Location; Bot:om Panel
Forthell.S.A.
FCC WARNING :
This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may
cause harmful interference unless the modifications are expressly approved in the instruction manual. The user
could lose the authority to operate this equipment if an unauthorized change or modification is made.
NOTE :
This equipment has been tested and found to comply with the limits for a CLASS B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment may cause harmful interference to radio communications, if it is not
installed and used in accordance with the instructions. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures;
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Selecting fine audio equipment such as the unit you've just purchased is only the start of your musical
enjoyment. Now it's time to consider how you can maximize the fun and excitement your equipment offers.
This manufacturer and the Electronic Industries Association's Consumer Electronics Group want you to get
the most out of your equipment by playing it at a safe level. One that lets the sound come through loud and
clear without annoying blaring or distortion — and, most importantly, without affecting your sensitive hearing.
Sound can be deceiving. Over time your hearing "comfort level" adapts to higher volumes of sound. So what
sounds normal can actually be loud and harmful to your hearing. Guard against this by setting vour
equipment at a safe level BEFORE your hearing adapts.
To establish a safe level:
• Start your volume control at a low setting.
• Slowly increase the sound until you can hear it comfortably and clearly, and without distortion.
Once you have established a comfortable sound level:
• Set the dial and leave it there.
Taking a minute to do this now will help to prevent hearing damage or loss in the future After all we want
you listening for a lifetime.
We Want You Listening For A Lifetime
Used wisely, your new sound equipment will provide a lifetime of fun and enjoyment. Since hearing
damage from loud noise is often undetectable until it is too late, this manufacturer and the Electronic
Industries Association's Consumer Electronics Group recommend you avoid prolonged exposure to
©xcGSsive nois6. This list of sound levels is included for your protection.
Decibel
Level _ Example
40
50
60
70
80
Living room, refrigerator, bedroom away from traffic
Light traffic, normal conversation, quiet office
Air conditioner at 20 feet, sewing machine
Vacuum cleaner, hair dryer, noisy restaurant
Average city traffic, garbage disposals, alarm clock at two feet.
THE FOLLOWING NOISES CAN BE DANGEROUS UNDER CONSTANT EXPOSURE
90
100
120
140
180
Subway, motorcycle, truck traffic, lawn mower
Garbage truck, chain saw, pneumatic drill
Rock band concert in front of speakers, thunderclap
Gunshot blast, jet plane
Rocket launching pad
Information courtesy of the Deafness Research Foundation.

DPC-981/782/781 (En/K)
Connect headphones.
Close the top cover.
• Accepts the supplied headphones, or other optional head¬
phones with a mini plug.
• The REMOTE terminal can be used only when the unit has
headphones with remote controller. (See "Accessories".)
Make sure the HOLD switch has been
released.
• Press down on the central front portion of the lid until it clicks.
Release the HOLD switch when performing an ooe'ation
3 Open the top cover.
Place a disc.
Place with
labeled side up
•m Start playback.
helld
♦
j
D 1 DOS
Track number Elapsed time
of the track
• The power comes ON and playback begins.
I Adjust the volume.
To decrease
volume
To increase
volume
0 HD
Volume display
The letter written on the hand in each illustration accompanying
the text indicates the position of the pressed key on the unit.
A Skip (Hd^, ► M) keys
Press either key to skip tracks.
B P.MODE/SEARCH (Play mode/Search) key
Press when using the program playback function or press together
with one of the Skip keys to initiate the fast forward or fast reverse
operation.
C REPEAT key
Press tor using various playback features.
D Play/pause ( ► i i) key
Press to play a disc, pause playback or switch power ON.
E Stop/off ( ■ ) key
Press to stop the disc, turn power OFF or recharge the unit.
F OPEN key
Use to open the top lid.
G D.A.S.C. (Digital Anti Shock Circuit) key
Press to switch the Digital Anti-Shock Circuit which prevents sound
from skipping.
H B.BOOST (Bass Boost) key
Press to activate low frequency compensation. This does not
operate with connection at the LINE OUT terminal.
/ VOLUME control
Turn to adjust the listening level. This does not operate with
connection at the LINE OUT terminal.
J HOLD switch
Use to turn the hold function on/off.
K REMOTE/PHONES (Remote/headphones) jack
L DC IN (External DC power input Jack) jack
M LINE OUT jack
• Secure the disc by pushing a position near the center hole
until It clicks
To pause playback temporarily
0
• When the ► l lkey is pressed during playback, it pauses tempo¬
rarily. Pressing the key again resumes playback.
To Stop playback
. 1 ^' 10HB:P3
• The total number of tracks and the total playing time of them
will be displayed.
To turn power OFF
After stopping playback, press tha ■ key again.
Auto power-Oft function
If no operation key has been pressed for 3 minutes while the
unit is in the stop mode, the power is turned OFF automati¬
cally to prevent battery power consumption.

Track selection by track skip
To skip _/
backward ^ ^
• The same number of tracks as the times the key is pressed can
be skipped.
• When the key is pressed once during playback, the played
position returns to the beginning of the current track being
played.
Fast forward, fast reverse
Perform the following procedure during playback.
O Press the P.MODE/SEARCH key.
• Go to the next step within b seconds.
3 i =
Preaelng the REPEAT key hi the pley or stop mode allowi you to
en|oy various pleybeck features.
f Press the REPEATkey>
CM3C-981/782/781 (En/K)
Each press swHchas the repeat modes as follows.
1 *“ O Cancelled position "I
Returns to the normal play OFF
mode. _
O One-track repeat [” ■■ ■ ■■
The track being played or nn P
selected track will be Ull C
played repeatedly.
O Alt-track repeat
All tracks on the disc will
be played repeatedly. ^
O Shuffle play ~
All tracks on the disc will /sSSi C U l IP
be played in a random or- tSss^ D n U r
der. ■
Compensation of low frequencies
The low fraquencias sound which is fait in haadphona can ba
boostad. ,
Each prass of tha kay switchas tha moda as follows.
O Bass Boost 1
Low frequencies are 3 j
O Bass Boost 2
Low frequencies are D
boosted more than Bass ^ i u C J
Boost 1.
0 Bass Boost OFF mm i::"::;::::.'.'!
Normal tone reproduc- j Q '-f ^
tion. _.
Indicator goes off. Goes off.
0 Press the or key.
Hold tha kay prassad during playback.
* Playback resumes from the position where the key is released.
» The REPEAT key may sometimes be invalid if it is pressed near
the end of a track. In this case, press the REPEAT key after
playback of the current track has completed.
• In case shuffle play is selected during playback, the playback of
the selected mode starts after the current track being played
has completed.
• The repeat of ® or © above stops after 16 times of repeats.
Note on the key operation
The operation keys of the main unH except for the volume
control are defeated.
This position prevents undesired operation when the unit is
put in a bag, etc.
• Be sure to release the switch before performing any opera¬
tions. Operations cannot be performed if it is in the HOLD
position.
Desired tracks can be played in the desired order.
Preparations
• Enter trie stop mode by pressing the ■ key while playback.
Press tha P.MODE/SEARCH key.
Select the desired track numbers in
the order you want to play them.
0 Sotect a track...
To skip _/
backward \ ^
_\_To skip
A 1 forward
Programmed order
Track number blinks I ■■■ 1
during selection i&~zD BP'- U I
0 And antar K.
D3P-D !
• Select other tracks m the desired order by repeating O and ©
above
• Up to 32 tracks can be programmed at a time.
Start playback.
%
To change a programmed content
O Ensure that the unK is in stop moda.
0 Display the content to be changed.
S3
OlP-OH
Track number Programmed
order
• Press the P.MODE/SEARCH key repeatedly until the pro¬
grammed order containing the track number to be changed is
displayed
0 Change the track number.
ID Select a track...
(2) And enter it.
-s3
-1
^^- 03 ^ - 0 4
--
if~D3P-04
To check the programmed contents
O Ensure that the unit is in stop mode.
0 Press tha P.MODE/SEARCH key.
Track number Programmed i
order ;:
• Each press of the P.MODE/SEARCH key displays the next
track number in the programmed order.
To clear the program
O Ensure that tha unit
is in stop mode.
0 Press the ■ key.
\t& DBP-DV
lDPB:P3f
• Opening the lid cancels the program.

DPC-981/782/781 (En/K)
Display
Lights in program mode. -
Lights up when the HOLD switch
is set to the HOLD position.
Displays the D.A.S.C. mode. -
The disc status is displayed.
At the time of D.A.S.C. ON, the re- ■
sidual memory amount is displayed.
Repeat mode indicator which lights ■
when one of the repeat modes is
activated.
-OCmi P Q i O —
Shuffle mode indicator which lights when
- the shuffle mode is activated.
B.B008T indicator which lights
- when Bass Boost is activated.
Battery duration indicator which lights
- during recharging and blinks when the
remaining battery power is low.
- Time/character information display
- Displays the track number.
Catd remote control unit (For DPC~981, DPC‘782}
Card remote control unit (tor uru-auh uru-ro^/
When thecard remote control unrtieuMd, connect the ACadaptor or car battery adaptorto the mainunlt. The card remote control
unit cannot be used if the main unit is powered from batteries.
Stop/power off key ■
Skip keys
P.MODEysearch key
Operating range (Approx.)
REPEAT key
B.BOOST key
VOLUME keys
After setting the volume
control of the mam unit
to the maximum
position, adjust the
listening volume wrth
these keys.
The keys with the same names as the keys on the main unit
function the same as the kevs on the main unit.
Remote
control unit
fluorescent lamp. In such a case, change the unit position to prevent erroneous operation.
• For battery replacement, use a commercially-avaiiapie innium batteiy (CR2025>,
* DJk.S.C. (Digital Anti Shock Circuit)
It prevents sound skipping by storing the CD's digital data in memory, and then playing back
from the memory.
M9chattism of D.A.S.C.
Reproduced sound
. In case of vibration above a certain degree, the mermory data may be exhausted and the guard from
sound skip may become temporarily ineffective.
Setting the DA.S.C.
Each press changes the mode as follows.
O D.A.S.C. HI
Digital data of about 20 seconds >5 stored m memory.
This IS the anti-shock play mode with a large vibra¬
tion-resistance effect.
o D.A.S.C. LOW
Digital data of about 6 seconds is stored m memory
This mode provides a lower vibration resistance but
better sound Quality than the D.A.S.C. Hi mode.
— o D.A.S.C. OFF (cancel)
When the player is used m a place free of vibration,
it is recommended to release the D.A.S.C to ex¬
tend the play time by reducing the battery power
consumption.
• The reproduced sound is interrupted during switching
What iMoit to b« « swioua troublo m*v tomotlitioo bo duo to • olmplo mlotako. B^loro^U^ toe
IlJS^irtho Homo ohown In tho tollowin* toblo onoin. IH yon roquot owyldns (too to tho
_^ibboototo.^ ♦ ka nriAv b* charasd in som# msm«)
Symptom
Cause
Remedy
No operation occurs
when operation keys are
pressed.
• The HOLD switch is set to HOLD.
• The batteries are exhausted.
• The disc is placed upside down,
• Condensation has occurred inside
the unit.
• The AC adaptor or car battery adap¬
tor is disconnected.
• Deactivate HOLD status.
• Replace all of the alkaline batteries, ^
or recharge the rechargeable batter¬
ies.
• Place the disc with the labeled side
up.
• Leave the unit for about 1 hour be¬
fore re-use,
• Connect it properly.
No sound is heard from
the headphones.
• The headphones are connected in¬
completely.
• The volume is set to the minimum
position on the main unit or remote
control unit.
• Insert the plug securely into the
headphones jack.
• Adjust the volume on the main unit
or remote control unit.
Sound skips, or is inter¬
rupted.
• The D.A.S.C. is set to "OFF".
• A strong vibration that exceeds the
capacity of the D.A.S.C. has occurred.
• The disc is dirty.
• The lens is dirty.
• The headphone plug is dirty.
• Tho battories are low
• Setthe D.A.S.C. to "ON". ^
• Place the unit in a place not subject '
to vibration. ■
• Clean it.
• Clean it.
• Clean it.
• Replace or recharge the batteries.
Noise interferes.
• The headphone plug is dirty.
• The batteries are low.
• The headphones are connected in¬
completely.
• Clean it.
• Replace or recharge the batteries.
• Insert the plug securely into the head¬
phones jack.
Rechargeable batteries
cannot be recharged.
• Commercially-availabie recharge¬
able batteries are used.
• Batteries have been inserted to the
"(D LONG PLAY" side.
• Use the special rechargeable
batteries (NB-130,NB-77 or NB-88).
• Do not insert batteries to the "(2)
LONG PLAY" side.
I'.^^^is system uses a microcomputer so it may malfunction due to external noise or interference. In such
a case, unplug the power cord and remove the batteries, then plug the power cord again and insert the
2. Erroneous operation may occur when the headphone plug is plugged or unplugged; but this is not a

Ensure that the power of the all of the components is off before connecting the cofds.
DPC-981/782/781 (En/K)
[Mains power operation
AC power outlet
Conrtect to
cigar lighter
socket.
Car battery powered operation
• When the unit is not used, unplug the car battery adaptor. (Otherwise,
the car battery may run out, with some car models.)
• The plug may not match the cigar lighter socket of some car models.
• If the unit cannot be operated with the car battery adaptor connected,
suspect the possibility of a blown fuse. The fuse can be replaced by
turning the electrode on the tip of the adaptor plug. When replacing the
fuse, be sure to use a fuse with a rating of 1 A.
Car battery adaptor
(Cars with DC-12V battery only)
See “Accessories".
* t ♦
i I A
Notes:
* 1 The REMOTE terminal can be used
only when the unit has headphones
with remote controller.
Ho rv3t use this terminal for other
purpose than the above.
*2 .With connection to the UNE
OUT terminal, no sound will
be put out from the
PHO^S terminal.
ForDPC-782
Listening through car audio
* If sound IS not produced, change the tape playing
direction of the car stereo
(Sound IS not produced if the car stereo is set to
play tape side B )
• Audio reproduction may be impossible with the
following types of car stereo Insert into
Models which function by detecting the tape cassette
tension (With these car stereo models, the Car deck slot
cassette adaptor is eiected automatically when it
IS inserted I
Car cassette adaptor
See "Accessories".
methods Car stereo
ra isi
» Insert the Car cassette adapter by setting the played
edge and cord positioned as shown in the illustra¬
tion.
I Listening through an amplifier with
CD input jacks
• Connect the cable to the amplifier's CD input jacks.
• For detailed playback procedures, please read the
instruction manual of your amplifier.
• This connection may be impossible with some am¬
plifiers.
^ Audio cord
(Commer- ^ ,nw;t ^
cially CO
available). Amplifier
CD input terminal connection
r^cfiargaabla battaria* should ba tha battarias providad as standard accassorias or optional
MB:,?? or hjBiSi- Navar usa othar battarias than tha rachargaabla battarias manufac-
turad for axclusiva usa wKh KENWOOD products.
This unit can be powered with three kinds of supplies including the batteries, household power
line and car battery.
The batteries may either be rechargeable batteries manufactured specially by KENWOOD or
alkaline baneries. Be sura to remove tha batteries from the unit when it is not to ba used for
a long period (of more than a weak).
O Insmt rachargoabid battarias fol¬
lowing tha polarity indications
totha”) PLAY or CHARGE" sida.
SEi
S Sat tha powar OFF.
O Plug in tha AC adaptor.
Connect to DC IN .ack _
O Walt for 5 saconds, than press
tha ■ kay twica quickly.
O Aftar racharging, unplug tha AC
adaptor from this unit.
Do not insert batteries to the *’ 2 LONG
PLAY''side for charging.
• Be sure to close the top cover of the unit before
proceeding to recharging.
• Recharging is not possible during playback Be
sure to set the power OFF before starting re¬
charging
• Recharging completes m about 4 0 hours with
the NB-130or about 3 0 hours with the NB-77 or
NB-88 Do not recharge batteries for longer
period than above
During recharging After recharging
Battery indicator lights Extinguishes.
The unit returns to the power OFF status.
• Rechargeable batteries can be recharged for
about 500 times When the playable time per
recharge reduces, please newly purchase the
optional NB-130. NB-77 or NB-88 rechargeable
batteries.
Use of two batteries
O Open the cover.
O Insert two rechargeable batteries
or two LR6 alkaline batteries fol¬
lowing the polarity indications to
the “iV PLAY or CHARGE" side.
O Close the cover.
• When using a rechargeable battenes which are new
or which have not been used for more than 2
months, the operating period may be shorter than
normal. This is due to the properties of the battery
and not a malfunction. After recharging, use the
batteries on the unit until there are exhausted.
The original performance of the battery perf onmance
can be recovered by repeating this cycle a fewtimes.
Use of four batteries (long-time
playback)
Long-time continuous playback becomes
possible when two rechargeable batteries
or two LR6 alkaline batteries are inserted
on the "(I^PLAY or CHARGE” side and two
LR6 alkaline batteries are set on the ”( 2 )
LONG PLAY” side.
Insert two LR6 alkaline batteries following
the polarity indications to the “(J) LONG
PLAY” side.
• We recommend the use of alkaline batteries
(LR6) because the playable time may some¬
times extremely short when manganese batter¬
ies are used.
• Always replace all batteries at a time.
Always insert a pair of batteries of the
same type to the "X PLAY or CHARGE” |
side and to the "(i) LONG PLAY” side.
I Battery duration indicator
The duration at which the battery indicator
starts to blink is variable depending on the
type of battery used
Refer to the table on the right
Battery duration
indicator
Battery Type
Blinking Timing
Treatment
Recnargeabie
battenes
When tne batteries are
nearly exhausted
In a while, the power will be turned off auto¬
matically. Then recharge the batteries.
Alkaline batter¬
ies
When the batteries are half
exhausted
Playback is possible while the indicator is
blinking.

MaiiW^nce
Simple care
Care of lens
When the lens in the pick-up gets dirty, nnalfunctions including the innpossi-
bility of playback may occur. The lens should be cleaned using a commercially-
available camera lens blower, etc. Do not touch the lens to prevent damaging
the mechanism. Also do not use a lens cleaner or disc cleaner product.
Care of main unit
When the unit gets dirty, clean with a soft, dry cloth. If the unit is stained seriously, a moistened cloth
can be used. Do not use benzine or thinner for these will damage the unit.
Cleaning the plug
Wipe the headphone plug with a soft cloth to keep clean.
A dirty plug may cause noise or malfunction.
Caution on disc used
Usable discs ^
This unit is capable of playing discs marked with . Other discs cannot be played. 8 cm single CDs
can be played as they are; do not use a commercially-available single CD adaptor.
CD accessories
The CD accessories (stabilizer, protection sheet, protection ring, etc.) which are marketed for improving
the sound quality or protecting discs as well as the disc cleaner should not be used with this system
because they may cause malfunction.
Handling
Hold compact discs so that you do not touch the playing surface.
Do not attach paper or tape to either the playing side or the label side of compact discs.
The paste left on the label surface after a sticker has been peeled off is a factor which may cause
malfunction.
If the surface is sticky due to remaining paste, be sure to clean it with alcohol before use.
Never play a cracked or warped disc.
During playback, the disc rotates at high speed in the player. Therefore, to avoid danger, never use a
cracked or deformed disc or a disc repaired with tape or adhesive agent.
Cleaning
If fingerprints or foreign matter become attached to the disc, lightly
wipe the disc with a soft cotton cloth (or similar) from the center of the
disc outwards in a radial manner.
Storage
When a disc is not to be played for a long period of time, remove it from the CD player and store it in
its case.
Precaution against condensation
Immediately after a room is heated or in a room with high humidity (or vapor), the unit may malfunction
due to the condensation of dew or mist on the pick-up lens. In such a case, leave the unit for about
an hour before trying to use is again.

Format
System. Compact disc digital audio system
Laser. Semiconductor laser
Audio
Frequency response.
Headphone output (16 Q, 1 kHz)...
(Headphone output level/impedance.
LINE output level/impedance.
Power supply
External DC supply.
Rechargeable batteries.
Commercially-available alkaline batteries.
Battery life (continuous playback) Repeat playback stops after 16 times.
(Figures inside parentheses are the values when D.A.S.C. is ON.)
Commercially-available alkaline batteries (LR6/ AA) x 4.
20 Hz ~ 20 kHz, ±3 dB
. 10 mW + 10 mW
. max. 450 mV/2.2 Q)
. 550mV/702f2
. DC 4.5 - 6 V
. DC 2.4 V
. DC3V
Approx. 40 (34) hours
Commercially-available alkaline batteries (LR6/ AA) x 2. Approx. 18.5(17) hours
Rechargeable batteries (NB-130) x 2. Approx. 9.0 (8.0) hours
With 2 commercially-available alkaline batteries and rechargeable batteries
Dimensions (W x H x D)
.Approx. 27.5(25) hours
133.6 mm x 26.5 mm x 151.8 mm
Weight (net)
(5-1/4"x1 -1/16"x6")
.270 g (9.5 oz.)
Notes :
1. KENWOOD follows a policy of continuous advancements in development. For this reason specifica¬
tions may be changed without notice.
2. Sufficient performance may not be exhibited at extremely cold locations (where water freezes).
Accessories DPC 981
DPC 782
DPC-781
AC adaptor
1
1
1
Noise canceling headphones *
1
- -
Battery for Noise canceling headphones *
R03/AAAx1
- -
Headphones
-
1 1
Rechargeable batteries
NB-130 X 2
NB-130 X 2
NB-130 X 2
Card remote control unit
1 1
-
Car battery adaptor
-
1
-
Car cassette adaptor
- 1 -
"" Please refer also to the separate instruction manual.
The provided accessories are variable depending on the areas where the product is sold.
The accessories which are not equipped as standard are optionally available. For details, please consult your
dealer.
I^f —your records
lx I I ^ yy I J Record the serial number, found on the back of the
unit, in the spaces designated on the warranty card,
and in the space provided below. Refer to the model
and serial numbers whenever you call upon your
dealer for information or service on the product.
Model
Serial Number