Kenwood Sovereing DV-5700 User manual

In compliance with Federal Regulations, following are repro-
duction of labels on, or inside the product relating to laser
product safety.
KENWOOD-Crop. certifies this equipment conforms to DHHS
Regulations No.21 CFR 1040. 10, Chapter 1, subchapter J.
DANGER : Laser radiation when open and interlock defeated.
AVOID DIRECT EXPOSURE TO BEAM.
Caution : No connection of ground line if disassemble
the unit. Please connect the ground line on
rear panel, PCBs, Chassis and some others.
70%
MULTIPLE DVD VCD CD PLAYER
© 2001-8 PRINTED IN KOREA
B51-5750-00 (K/K) 2492
PHONES
STANDBY
DISC SKIP
PURE AUDIO
MODE
PHONES LEVEL
POWER
VIRTUAL
SURROUND
ON OFF
MI N MAX
SAMPLING
192kHzfs
DISC 1 DISC 2 DISC 3 DISC 4 DISC 5
OPEN/CLOSE
96kHzfs
Knob *
(K29-)
Knob *
(K29-)
Panel *
(A60-)
Phone jack
(E11-0190-05)
TV SCART
YC
R C B
VCR SCART
COAXIAL
COMPONENT
VIDEO OUTPUT
DIGITAL OUTPUT
(PCM/BIT STREAM)
INTERFACE PROGRESSIVE
OPTICAL
S VIDEO OUTPUT
1 2
VIDEO
OUTPUT
6CH. OUTPUT
COMPONENT VIDEO OUTPUT
FRONT SURROUND SUB WOOFER
CENTER
MIX LINE
OUTPUT
1
2
L
R
Front glass
(B10-3609-02)
DV-5700
SERVICE MANUAL
DVF-R9050/R9050-S
Knob *
(K29-)
Metallic cabinet *
(A01-)
Pin jack
(E63-1128-05)
Slide switch
(S31-1623-05)
Pin jack
(E63-1156-05)
AC power cord bushing
(J42-0083-05)
Rectangular receptacle
(E58-0027-05)
Oscillating module
(W02-2732-05)
Cylindrical receptacle
(E56-0031-05)
Pin jack
(E63-1171-05)
AC power cord *
(E30-)
Pin jack
(E63-1158-05)
Illust. is DVF-R9050
*Refer to parts list on page 61.
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299

Video cable (1)
(E30-1427-05)
Audio cables (3)
(E30-0505-05)
Joystick remot control unit(1)
(A70-1489-05): RC-D0711
Batteries (R6/AA)(2)
Battery cover (A09-1124-08)
S Video cable(1)
(E30-2956-05)
Coaxial cable (1)
(E30-2365-05)
DV-5700/DVF-R9050/R9050-S
2
CONTENTS / ACCESSORIES / CAUTIONS
CONTENTS / ACCESSORIES / CAUTIONS............. 2
DISASSEMBLY FOR REPAIR....................................3
BLOCK DIAGRAM ......................................................4
CIRCUIT DESCRIPTION ............................................5
MECHANISM DESCRIPTION...................................22
ADJUSTMENT ..........................................................26
WIRING DIAGRAM ...................................................27
PARTS DESCRIPTIONS ..........................................28
PC BOARD .............................................................. 29
SCHEMATIC DIAGRAM .......................................... 36
EXPLODED VIEW ....................................................58
PARTS LIST..............................................................61
SPECIFICATIONS ......................................Back cover
Contents
Accessories
CAUTION
VISIBLE LASER RADIATION
WHEN OPEN. DO NOT
STARE INTO BEAM.
Location: Back panel
Inside this laser product, a laser diode classified as
Class 2 laser radiation is contained as alerted by the
internal caution label shown above. Do not stare into
beam.
Location: DVD laser pick-up unit cover inside this
product
CLASS 1
LASER PRODUCT
The marking of products using lasers
(For countries other than U.S.A., U.S.-
Military and Canada)
The marking this product has been classified as Class
1. It means that there is no danger of hazardous
radiation outside the product.
Cautions
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299

DV-5700/DVF-R9050/R9050-S
3
DISASSEMBLY FOR REPAIR
1
5
2
3
6
4
5
HOOK ( x2)
HOOK
x2
Guide
6
3
4
HOOK
GUIDE
ARM
DRIVE
GEAR
HOOK
LOADING
GEAR (A)
(Free)
PROTRUSION OF TRAY
2
1
5
REAR
1. How to Remove Tray
1. Remove the front panel and flexible cable.
Disassemble the X25, X35 and power supply pcb with
sub chassis if it is a difficult.
2. Push and hold the lever( )to clockwise and pull out the
tray to frontwards( ) where the hook of tray( ) meets
with guide( ).
3. Push hooks( ), both sides, inwards and release them
from guides( ).
4. Pull hooks of tray( ) outwards and remove the tray
upwards( ).
2. How to Assemble Tray
1. Adjust the position of drive gear as figure( ).
Check traverse unit is at the lowest position.
2. Load the tray on the loading mechanism.
Check the position where the loading gear(A) is free( )
3. Meet the hooks with guides and push hooks to load the
tray( ).
4. Set the right side hook to loading mechanism( ).
5. Set the left side hook to loading mechanism with pulling it
outwards( ).
6. Push the tray backwards( ).
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299

DV-5700/DVF-R9050/R9050-S
4
BLOCK DIAGRAM
DAT0-3
VIDEO ENCODER
PROGRESSIVE SCAN CONVERTER
MP3 DECODER
TRACKING
FOCUS STD0-7 STD0-7
VD0-7
IEC OUT
B/Cb OUT 0-9
R/Cr OUT0-9
G/Y OUT0-9
Y, C
G, B
Y, Cb, Cr
Y
COMP
C
AV1 RGB OUT
DVD RGB
AV2 RGB
DVD Y, C, COMP
AV1 Y, C, COMP
AV2 Y, C, COMP OUT
AV2 Y, C, COMP
AV1 Y, C, COMP OUT
AV2 AUDIO
DVD AUDIO
AV1 AUDIO OUT
AV1 AUDIO
AV2 AUDIO OUT
AV2 FUNC,BLK
AV1 FUNC,BLK
AUDIO DAC
DRIVE
AUDIO SW I/P SW SCART CONTROL
VIDEO SW CONTROL
DMIX
AUTO (FL, FR)
AUTO1 (SL, SR)
AUTO2 (C, SW)
Fs OUT
27M
SCAN CONVERTRE
PROGRESSIVE
VIEDEO ENCODER
ODCADSC
MP3
CPPM,
DRIVE
DAC
IEEE1394
POWER
: AC230V~ 50Hz(E)
: AC110-120V
: AC120V 60Hz
50/60Hz
(K)
(Y)
A+9V/-9V
M+9V
AGND
FL-35V
FL+-
DGND/SGND
D+5V/3.3V
EV+12V
EVGND
EV+5V
DAC+5V
A+7V/-7V
A+5V/-5V
D+2.5V
PLAY/OPEN/CLOSE
CONTROL
/MGND
AUDIO
DVD CD
/220-240V~
PROG
Y
C
13.5M
384Fs
768Fs
Y, Cb, Cr/R,
MP3 DATA , LRCK, BCK
PLL/DSL
HF
SERVO CONT
CIRC/DAC
SERVO CONTROLLER
MN67706
ADVANCED DISC OPTICAL DISC
CONTROLLER
ATAPI
ROM DEC
ECC
4MDRAM
MN103S13B
IC101
IC900 & SPREM
MP3 DECODER
DECODER
CPPM
IC400
MN5C27D4H
CSS2
DISSCRAMBLE
8M FLASH ROM
IC901
CSS DISSCRANBLE
MN677521HB
AV DECODER
VIDEO DECODER
MPEG,SUB PICTURE
MPEG,DTS,AC3,LPCM
AUDIO DECODER
ENCODER
NTSC/PAL
PCM &
SPDIF
VIDEO DAC
SDRAM I/F
OSD
64M SDRAM
IC301
ADDRESS DATA BUS
MF3 SW
DVD u-COM
IC201
8M FLASH ROM
IC207
8M FLASH ROM
IC215 IC500
DETECTOR
WATER MARK
MF7F015
EEPROM
IC206
S/P
APC
RF AMP
DRIVER
AN8499
MM
TRAVERSE/
LOADING SPDL
PICKUP
AN8708
AN8708
FRONT-END
PROCESSOR
COLOR, NR CONTROL
BRIGHT, SHARP, GANMA
PROGRESSIVE SCAN
CONVERTER
CGMS, MCROVISION
PROGRESSIVE SCAN CONVERTER
IC700
16M SDRAM
IC702
16M SDRAM
IC701
FL12200
VIDEO
DAC
ADV7196
IC800
YUV TO RGB MATRIX
COLOR, NR CONTROL
BRIGHT, SHARP, GANMA
VIDEO ENCODER
IC600
CAPTION CONTROL
CGMS, MCROVISION
3ch
6ch
DAC
VIDEO
ADV7190
13.5M
6.75M
6.75M
6.75M
MM1540
IC601
MUTE
ONLY
I/P SW Y OUT
J604
Cb OUT
Cr OUT
J601
OUT
COMPOSIT
J602
J S1
S OUT
J S1/S2
J603
S OUT
VIDEO FILTER & BUFFER
BLK. FUNC
IC401
SCART AV1
SCART AV2
S601
PROGL SW IC1
SYSTEM u-COM
MN101C28CMA
OPEN
TRAY SW
TRAY SW
CLOSE
M
LOADING
POSITION
SENSOR
ROTARY
M
FOR FL, FR
IC901
KAN06
KAN06
FOR SL, SR
IC902
ONLY
C, SW
KAN06
IC903
DATA SW
FRONT
PCM1602KY
6ch DAC
IC205
192k 24bit
FOR FL, FR
FOR SL, SR
96k 24bit
FOR C, SW
96k 24bit
PCM1748
FOR DMIX
IC204
2ch DAC
96k 24bit
60kHz
OUT SW
60kHz
60kHz
60kHz
LPF SW 110kHz
Q222-225
MUTE
(E)TYPE
Q226-229
MUTE
Q230-233
MUTE
Q234-237
MUTE
J201
MIX L
MIX R
FR
FL
SR
SL
SW
C
COAX.
J202
A201
OPT.
MP3
X35 (IC900) 27MHz
(IC210)
1/2
X35
PLL
X35 (IC300)
1/2
X35 (IC211)
33.8688MHz
X25 (X302)
X25 (X301)
36.864MHz
Fs SW
1/2
(IC904)
X35 SW
MP3
MP3
SW
X35 (X201)
1/2
DVD u-COM
X35 (IC201)
SW POWER SUPPLY
REG
X25 (Q201-204)
REG
X25 (IC602,603)
X35 (IC303)
REG
X25 (IC218)
REG
IR
KEY
DOT DRIVER
IC1
LED
ED1(16-ST-43GNK)
FL J501
J502
DMIX
IC212
SW
MAIN DATA LINE
AUDIO LINE
VIDEO LINE
(E)TYPE ONLY
(IC209)
X25
OUT
OUT
COMPOSIT
OUT
(E)TYPE
(E)TYPE
ONLY
(E)TYPE
ONLY
AVDEC
SCART CONTROL
DRIVE
DRIVE
DRIVE
PICKUP UNIT
(X14-7160-10)
MECHA.
(X00-3060-11)
CLK SYSTEM
(X35-2290-11) (X25-646X-XX)
DV-5700,DVF-R9050
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299

DV-5700/DVF-R9050/R9050-S
5
CIRCUIT DESCRIPTION
TEST MODE
This model has 3 kind of test modes; unit inspection, factory test mode, measurement. In this manual, items of repair, test
mode and inspection are available.
Setting
Turn power on with pressing "PAUSE" key. Display shows "TEST".
Turn power on with pressing "DISC1" key. Display shows "INSPECTION".
Cancellation of Setting
Turn power off.
Key vs Function
Keys which described in the following table work as it is.
TEST MODE
Key Mode Display Operation
PLAY
-Playback time Disc Playback
SKIP-UP STOP
All segments light î
Niagara mode î
Playback time î
Display shows cyclically by pressing key
SKIP-UP PLAYBACK Playback time Playback next chapter/track #/program #
SKIP-DOWN PLAYBACK Playback time Playback before chapter/track #/program #
STOP - Time Stop to operate and return to first step of this
test mode.
DISC2 PLAYBACK
MUTE ON îMUTE
OFF
Mute works cyclically on or off.
DISC3 -LPF 60k îLPF 110k Speaker protection works cyclically on or off.(Cut-
off freq. Change 60k or 110k)
DISC4 -WIDE1 îWIDE2
NORMAL WIDE mode changes cyclically WIDE1 or WIDE2.
DISC5 -SCART RGB îSCART
YC îSCART Through
Video signal of SCART changes cyclically
RGB(DVD) îY/C(DVD) îThrough(AV1 AV2)
OK or IC*** Self check mode(refer to Servo Error Code)
STOP+DISC1 STOP Rotary turns clockwise.
STOP+DISC2 STOP Rotary turns counter clockwise.
STOP+DISC3 STOP Tray opens
STOP+DISC4 STOP Tray closes
DISC SKIP
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299

DV-5700/DVF-R9050/R9050-S
6
CIRCUIT DESCRIPTION
INSPECTION
Key Mode Display Operation
PLAY - Playback time Disc Playback
SKIP-UP STOP
All segments light î
Niagara mode î
Playback time î
Display shows cyclically by pressing key
SKIP-UP PLAYBACK Playback time Playback next chapter/track #/program #
SKIP-DOWN PLAYBACK Playback time Playback before chapter/track #/program #
STOP - INSPECTION Display shows cyclically by pressing key.
inspection mode.
STOP STOP Model/destination/region
code / Main -com version. Display shows cyclically by pressing key.
DISC1 PLAYBACK Jitter ***%Shows jitter value(binary value vs time deviation
of PLL-clock)
DISC2 -CPPM KEY ID 13 figures.
DISC4 -WIDE1 îWIDE2
NORMAL WIDE mode changes cyclically WIDE1 or WIDE2.
DISPLAY CONTENTS REASON CANCELING KEY REMARKS
Main processor doesn't work
Sio-0 bus damaged
No right position of rotary
Foreign matter inserted
No right position of rotary
Foreign matter inserted
E1102
No turn of rotary Foreign matter inserted OPEN/CLOSE or DISC
SKIP
E0101
No open Mechanism jam CLOSE Initialization
No show
No Close Mechanism jam Initialization
Disc full load
Not stop to turn the proper
position
Load disc at no proper position
Foreign matter inserted at
sensor
No show
Waiting Turn power off in open/close
mode. CLOSE Press the CLOSE key after turn the power on again.
OPEN/CLOSE or DISC
SKIP
Check the sensor of discs on
the rotary.
NO Remove the one disc after
turn power off
E0102
Playing Disc inside
No detection of disc
position
E0103
No contact with
main processor
No cancellation of
chucking
Poor disc chucking No
E1101
No
E1001 No
ERROR CODE OF MECHANISM
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299

DEFINITION CONTENTS CODE BLOCK TIMING
ODC(Optical Device Control)
MOD_NOT_CRCOK No CRCOK signal 0x4303 (ADSC,ODC,disc ,pickup) Read address error at lead in or focus jump.
MAS_ECC_ERR Abnormal ODC ODC
ERROR ODC No emission OK on disc and host in 5 secs.
LAYER_CMP_ERR Abnormal LAYER in seek mode -
OUT_PB_AREA_NG OUT of PB AREA -
DATA_TR_PLAY_NG DATA Track Play -
SEEK_NG_CHGNV No data caused seek error -
UNCORRECT_ERR No control data by demodulator
error -
INVALID_CMD_ERR Out of secter ID 0xD601 Over data from disc(DVD : 0xFFF)(VCD :
00:02:00 less)(CD : 0xFFF)
UNCORRECT_LEADIN No lead-in data by demodulator
error 0xD602 Time over in lead-in.
UNCORRECT_
KEYDET
No lead-in data by demodulator
error 0xD603
(ADSC,ODC,disc ,pickup)
ODC,disc
ERROR CODE OF CIRCUIT BY SELF CHECK MODE (TEST MODE)
DEFINITION CONTENTS CODE BLOCK TIMING
SERVO
TRAY_LOADING_ERR Tray Loading Error. 0x4000
ADSC, TRAY
Mechanism, Motor LSI
DCM_TRAYCTL_T(time out 5secs)
FOCUS_SVERR Focus Servo Error. 0x4100
ADSC, pickup &
actuator, Driver LSI
DCM_FCON_T(time out 5secs),
Lock NG, NG of seek.
SPINDLE_SVERR Spindle Servo Error. 0x4101 ADSC, Driver LSI, disc
Motor
DCM_DMON_T(time out 10
secs),Time out of checking
stop,Time out of start to turn.
DSC_DM_ERR
DSC Disc Motor Error.
Abnormal FG-period in
DVD, Abnormal turn of
disc motor,
0x4102 ADSC, Driver LSI, disc
Motor
DCM_DMOF_T(time out 10secs),
DCM_DMMODE_T(time
out100ms) Abnormal turn of
disc motor.,
CDC_CLV_ERR
6626 CLVS Failure.
Abnormal FG-period in
CD
0x4103 ADSC, Driver LSI, disc
Motor
DCM_DMOF_T(time out 10secs)
Setting abnormal CLV
TRAVERSE_ERR Traverse Motor Error. 0x4104
ADSC, Driver LSI, feed
Motor
DCM_INNER_T(time out 5secs)
TRACK_SVERR Tracking Servo Error 0x4105
ADSC, pickup &
actuator, Driver LSI
DCM_TRON_T(time out 1sec)
Command error,Focus jump
Lock NG (ReSartServo) NG of
SEEK_TIMEOUT_ERR Seek Time Out Error 0x4106
ADSC, pickup &
actuator, Driver LSI
Over 200 seek times
DSC_ERROR
DSC Error
(status data error)
ADSC
ERROR
ADSC
ERROR
ADSC
ERROR
ADSC
ERROR
ADSC
ERROR
ADSC Command error
DSC_NOTREADY DSC Not Ready Error ADSC ADSC REDY time out
DSC_TIM_ERR DSC TimeOut Error. ADSC Over of CLV OK Over
of command end
DSC_COM_ERR
DSC Communication
Failure.
ADSC No use
DSC_ATN_ERR DSC Attention Error. ADSC Error of CD-trick play and CD/DVD
seek. FC jump in DVD-play.
INVALID_MDTYP Out of Media 0x4300 ADSC No check of media, Error after
servo retry. Abnormal disc.
DONOT_QREAD_ERR
6626 QCODE do not
Read Error.
0x4302 ADSC Read error in Cue or
Rev play of CD
DSC_ESCAPE DSC Command Escape - ADSC
Stop servo operation after setting
the ESC flug in mode register of
ADSC.
FEP_IC_ERR
Adjustment error on data
slice offset
EEP
ERROR ADSC ,FEP jitter and data slice offset
adjustment error
FEP
DV-5700/DVF-R9050/R9050-S
7
CIRCUIT DESCRIPTION
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299

DV-5700/DVF-R9050/R9050-S
8
CIRCUIT DESCRIPTION
DEFINITION CONTENTS CODE BLOCK TIMING
DISC
1. No CD-ROM Volume Descriptor
Set, No Primary Volume Descriptor
2. No Beginning Extended Area
Descriptor
3. No NSR Descriptor of "NSR02"
4. Length error of Main Volume
Descriptor Sequence
5. Directry of length error on
VIDEO_TS/AUDIO_TS after root
DISERR_TT_SRP_NO TT_SRP=0 0x2111 Disc format
ISERR_TT_SRP_OVER Value >TT_SRP 0x2112
DISERR_TT_SRP_MISS
SRP is not meet with VTSN or
VTS_TTN
0x2113
DISERR_TT_SRP_
PTT_OVER Value >TT_SRP.PTT_Ns 0x2114
DISERR_TTU_SRP_NO TTU_SRP=0 0x2120 Disc format
DISERR_TTU_SRP_OVER Value >TTU_SRP 0x2121 Disc code
DISERR_PGCI_SRP_NO PGCI_SRP=0 0x2131 Disc format
DISERR_PGCI_SRP_OVER Value>PGCI_SRP 0x2132
DISERR_TMAP_
SRP_OVER Value>TMAP_SRP 0x2141
DISERR_TMAP_SA_NO TMAP_SA=0 0x2142
DISERR_TMAP_EN_NO MAP_EN=0 0x2143
DISERR_PGC_PGMAP_NO C_POSIT is OK,
No PGMAP in PGC 0x2150
DISERR_PGC_PG_NO C_POSIT is OK, PG=0 in PGC. 0x2151
DISERR_PGC_PG_OVER Value >PG in PGC 0x2152 Disc code
DISERR_PGC_C_PBIT_NO C_POSIT is OK,
No C_PBIT in PGC 0x2153
DISERR_PGC_C_NO C_POSITis OK, Cell=0 in PGC 0x2154
DISERR_PGC_CN_NO Cell=0 0x2155
DISERR_PGC_C_OVER Value >Cell in PGC 0x2156 Disc code
DISERR_PGC_BLK_NO Block Cell only 0x2157
DISERR_SEARCH_CN_NO No Cell# in search. 0x2160 Disc format
Disc code
DISERR_UDF
UDF Bridge NG 0x2100
Disc format
Disc code
Disc format
Disc format
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299

DV-5700/DVF-R9050/R9050-S
9
CIRCUIT DESCRIPTION
POWER ON
CD Tray close When initialize the mechanism,
it will display "INITI ".
DISC Position SW ON
Rotary SW ON
Traverse Unit Down
Initializing the RAM area • The "INITI NG " will be displayed if abnormal
and Backed up action is occurred during the stop mode.
• The "INITI OK "will be displayed if no error occurred.
1. Initializing the DVD Carrousel
1-1 Setting Method
• Insert the AC power plug to AC wall outlet with pressing the "STOP" key.
Port No. Port Name I/O Function
1 VSS O GND
2-4 KEY0-2 I Key input for AD.
5,6 KEY3,4 O Unused.
7 KISYU I Model selector.
8.9 KID0,1 I Destination selector.
10 VREF+ O Positive reference voltage for AD converter.
11 VDD O +5V
12 OSC2 I Clock input (10MHz).
13 OSC1 O Clock output.
14 VSS O GND
15 XI I Unused.
16 XO O Unused.
17 MMOD I GND
18 TXD0 O SIO0 data output port. Main processor contact.
19 RXD0 I SIO0 data input port. Main processor contact.
20 SCK0 O SIO0 clock output.
21 SB01 O SIO1 data output port. FL driver contact.
22 SB11 I SIO1 data input port. FL driver contact.
23 SCLK1 I SIO1 clock input.
24 FLCE O FL chip enable.
25 RESET I CPU reset.
26 E2CS O Unused.
27 P11 O Unused.
28 MECHA VR O Mechanism PCM output.
29 P13 O Unused.
30 LED DM O Unused.
31 REMOCON I Remocon code input.
32 POS SENS O Mecahnism position sensor.
33 MECHA FG I Mecahnism frequency generator(FG) signal input.
34 OPEN SW I Tray open switch sensor.
35 CLOSE SW I Tray close switch sensor.
36 12C SDA O IC400 control (I2C data). Scart drive/E2ROM
37 SB12 O Unused.
38 12C SCL O I2C clock.
39,40 P33,34 O Unused.
2. Main Microcomputer : MN101C28CMA(X25, IC1)
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299

DV-5700/DVF-R9050/R9050-S
10
CIRCUIT DESCRIPTION
Port No. Port Name I/O Function
41 TM+ O Tray motor positive port.
42 TRM- O Tray/rotary motor common port.
43 RM+ O Rotary motor positive port.
44 RGBL O Y signal.
45 AOP O Video signal selector. AOP=Pure Audio Mode.
46 YCBH O H=scart color-difference signal. L=RGB.
47 TRAY OPEN O Unused.
48 TRAY CLOSE O Unused.
49 POWER O H=on. L=power off.
50 FL OFF O Unused.
51 WIDE1 O Unused.
52 WIDE2 O Unused.
53 C OFF O C-signal of YC-signal on/off. H=on. L=off.
54-56 P52-54 O Unused.
57 CE O Power chip enable.
58-60 P61-63 O Unused.
61-68 LED18-11 O Unused.
69 POWER LED O Power LED(D9).
70 96kHz O 96kHz LED(D7).
71 DISC2 O Disc 2 LED(D2).
72 DISC4 O Disc 4 LED(D4).
73 VSS LED O Vss LED(D6).
74 AOP LED O AOP LED(D15).
75 SHOWER LED O Shower LED(D14).
76 192kHz O 192kHz LED(D8)
77 DISC1 O Disc 1LED(D1).
78 DISC3 O Disc 3 LED(D3).
79 DISC5 O Disc 5 LED(D5).
80 POWER MUT O Power mute.
Port No. Port Name I/O Function Active
HL
1 WAIT I Bus wait port.
2NRD
(ODC/AVDEC/SRAM) O Bus read port.
3 NWEL O Unused.
4NWEH
(ODC/AVDEC/SRAM/ROM) O Bus read port.
5 RAMCS(SRAM) O SRAM chip select.
6 ODCCS O ODC chip select.
7 AVCS(AVDEC) O AV decoder chip select.
8 ROMCS(ROM) O Flash ROM chip select.
9 SCLOCK(VDAC) O Clock output to VDAC (X35, IC600).
10 SDATA(VDAC) O Data output to VDAC (X35, IC600).
11 FRD(ROM) O Flash ROM read port.
12 WORD - Connected to VDD (+3.3V).
13~16 CPUADR0~3 O Bus address (0~3).
17 VDD - Supply voltage (+3.3V).
18 SYSCLK(AVDEC) O Clock output to AV decoder (X35, IC300).
19 VSS - Connected to GND.
20 XI I Connected to GND.
21 XO O Unused.
22 VDD - Supply voltage (+3.3V).
3. Port Function of DVD Microcomputer : MN102L62GGB (X35, IC201)
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299

DV-5700/DVF-R9050/R9050-S
11
CIRCUIT DESCRIPTION
Port No. Port Name I/O Function Active
HL
23 OSCI(CLK135) I System clock input (13.5MHz).
24 OSCO O Unused.
25 MODE I Processor mode selection. Expan.
Mode
26~33 CPUADR4~11 O Bus address (4~11).
34 AVDD - Supply voltage (+3.3V).
35~42 CPUADR12~19 O Bus address (12~19).
43 VSS - Connected to GND.
44 CPUADR20 O Bus address (20).
45 25BSY O Busy data output. Normal Busy
46 STBPSL O Unused.
47 HFMON O HF monitor output.
48 KMODE O Selection for writing the ROM. Writing Normal
49 AMUTE O Audio mute control.
50 CIRCEN(ENC) O Enable to Digital Servo Controller (X35, IC1).
51 PROGSW I Change-over the component terminal.
52 STBTI O Strobe output to MP3 decoder (X35, IC900).
53 FRSW O Flash ROM 1, 2 (X35, IC207, 215) change-over. Default
54 VDD - Supply voltage (+3.3V).
55 FEPEN O Enable to FEP (traverse).
56 CLKSEL O Clock selection.
57 STBDAC2 O Strobe output to ADAC (X25, IC205).
58 STBSP1 O Strobe output to serial-parallel converter (X25, IC224).
59 STBDAC1 O Strobe output to ADAC (X25, IC204).
60 ADSCEN(ENS) O Enable to Digital Servo Controller (X35, IC1).
61 VSS - Connected to GND.
62 WMINT I Interruption port from Water Mark Detector (X35, IC500).
63 E2CS O Chip select to EEPROM (X33, IC206).
64 SCSIBN O Enable control to jig for writing the ROM.
65 196BSY I Busy data input. Normal Busy
66 VDD - Supply voltage (+3.3V).
67 SCLK0 O SIO0 clock output to communicate between main
microcomputer and DVD system microcomputer.
68 SI0 I SIO0 data input to communicate between main
microcomputer and DVD microcomputer.
69 SO0 O SIO0 data output to communicate between main
microcomputer and DVD system microcomputer.
70 SCLK1 O SIO1 clock output for control ICs.
71 SI1 I SIO1 data input for control ICs.
72 SO1 O SIO1 data output for control ICs.
73 PULL UP0 I Unused.
74 PULL UP1 I Unused.
75 NMI I Unused.
76 ADSCINT I Interruption port from Digital Servo Controller (X33, IC1).
77 ODCINT I Interruption port from Optical Disc Controller (X33, IC101).
78 AVINT I Interruption port from AV decoder (X33, IC301).
79 ICRST O Reset signal output to periphery ICs.
80 MP3INT I Interruption port from MP3 decoder (X33, IC900).
81 ADSEP I Unused.
82 RST I Reset signal input.
83 VDD - Supply voltage (+3.3V).
84~91 CPUDT0~7 I/O Bus data (0~7) input and output.
92 VSS - Connected to GND.
93~100 CPUDT8~15 I/O Bus data (8~15) input and output.
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299

DV-5700/DVF-R9050/R9050-S
12
CIRCUIT DESCRIPTION
Port No. Port Name I/O Function
1~16 P0~1P15 I 8 bit or 16 bit 4:2:2 multiplexed Y/Cr/Cb pixel port.
17,25,54,63 VDD - Digital supply voltage (+3.3V).
18,24,33,55,64 DGND - Digital ground.
19 HSYNC I/O Connected to VDD.
20 VSYNC I/O Connected to VDD.
21 BLANK I/O Connected to VDD.
22 ALSB I Connected to digital ground.
23 TTXREQ O Connected to VDD.
26,39,42 AGND - Analog ground.
27 CLKIN I Clock input.
28 CLKOUT O Unused.
29,38,43 VAA - Analog supply voltage (+3.3v).
30 SCL I Serial interface clock input.
31 SDA I/O Serial data input/output.
32 SCRESET/RTC/TR I Connected to analog ground.
34 RSET2 I Used to control full-scale amplitudes of the video signals from the DAC D, E,
and F.
35 COMP2 O Compensation pin for DACs D, E and F.
36 DAC F O S-Video C/V /RED analog output.
37 DAC E O S-Video Y/U/ BLUE analog output.
40 DAC D O Composite Y/GREEN analog output.
41 DAC C O S-Video C/V/ RED analog output.
44 DAC B O S-Video Y/U /BLUE analog output.
45 DAC A O Composite Y/GREEN analog output.
46 COMP1 O Compensation pin for DACs A, B and C.
47 VREF I/O Voltage reference input for DACs or voltage reference output.
48 RSET1 I Used to control full-scale amplitudes of the video signals from the DAC A, B,
and C.
49 RESET I Reset signal input.
50 CSO HSO O Unused.
51 VSO/ CLAMP I/O Unused.
52 PAL NTSC I Connected to digital ground.
53 NC - Unused.
56 TTX I Connected to digital ground.
57~162 NC - Unused.
4. Port Function of Video Encoder /DAC : ADV7190 (X35, IC600)
Port No. Port Name I/O Function
1 SURH O Surround on/off control
2 H2CH O Front/Mix change-over (X25, IC212, 213) H:DOWN MIX L : L,R
3 BASS O DVD A BASS Management change-over (X25, IC801)
4 FRNTH O Unused
7 CLKSEL2 O VRQ change-over H : MP3 L: AV
16 L192 O Audio out LPF change-over H:60k L:110k
✽17 THRU O ADAC Through (X25, IC901~903)
✽18 IW0 O ADAC bit setting (X25, IC901~903)
✽19 IW1 O ADAC bit setting (X25, IC901~903)
✽20 DACMUT O ADAC mute (X25, IC901~903)
✽21 MMOD1 O ADAC Fs change-over (X25, IC901~903)
5. Serial-Parallel Converter : NJU3715G (X25, IC224)
✽ DVF-R9050 only
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299

DV-5700/DVF-R9050/R9050-S
13
CIRCUIT DESCRIPTION
Port No. Port Name I/O Function
1,9,32,46,53,73
104,116,142,156
160,166,172,179
184,191,197,205
VDD - Digital supply voltage (+3.3V).
2~4,6~8,10,201
203,204,206,207 MA0~MA11 O SDRAM address 0~11
5,14,27,42,52,60
70 83,92,105
120,147 157,163 VSS - Digital ground.
169,176,182 186
194,200,208
11 CLK121 - Connected to digital ground.
12,37,66,79,96
112,145,174,188 LVDD - Digital supply voltage (+2.5V) for internal logic.
202
13 XRST I System reset input. L : Reset
15 CLK81 - Connected to digital ground.
16 PLLAVDD - Main PLL supply voltage (+3.3v).
17 TCPOUT 0 Unused.
18 PLLAVSS - Connected to digital ground.
19 CLK27 I System clock input (27MHz).
20 PLLTEST I Test input port for main PLL. L : Fixed
21 CKIO I Decode clock change-over.
22 PLLVDD - Supply voltage (+2.5V) of internal logic for main PLL..
23,24 HMD1,HMD0 - Connected to digital supply voltage (+3.3V).
25 XHINT O Interruption to DVD microcomputer. L : Active
26 XDK O Acknowledgment to DVD microcomputer. L : Active
28 XWR I Write enable from DVD microcomputer.
29 XRD I Read enable from DVD microcomputer.
30 XCS I Chip select from DVD microcomputer.
31 HCLK I Clock input from DVD microcomputer.
33~36,38~41
43~45 HA1~HA11 I Address input from DVD microcomputer.
47~51,54~59
61~65 HD0~HD15 I/O DVD microcomputer data bus 0~15.
67 AUDSTR I Valid signal of bit stream input data.
68 ARQ 0 Unused.
69 VSTR I Clock signal input for bit stream.
71 VRQ O Request of program stream.
72 AVRTM I Sector separation signal.
74~78,80~82 STD0~STD7 I Bit stream parallel input 0~7.
84 EXTCK I External FS384 input terminal.
85 APLLVDD - Supply voltage (+2.5V) of internal logic for Audio PLL..
86 P5481 - Audio PLL ground.
87 PHCOPMO O Audio PLL phase comparison output.
88 APLLAVSS - Audio PLL ground.
89 NC - Unused.
90 APLLAVDD - Supply voltage (+3.3V) for Audio PLL..
91 ACKIO - Connected to digital ground.
92 VSS - Digital ground.
93 DCTEST - Connected to digital ground.
94,95 TESTSEL1,0 - Connected to digital ground.
6. AV decoder : MN677521HB (X35, IC300)
6-1 Port Function
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299

DV-5700/DVF-R9050/R9050-S
14
CIRCUIT DESCRIPTION
Port No. Port Name I/O Function
97~102,106,108 TEST4~TEST9
109 TEST3,1,0 O Unused.
103 CLKMON O Unused.
107 RFF O Unused.
110 IECOUT O IEC958 format data output.
111 DMIX O Audio down mix signal output.
113 DACCK O Over sampling DAC clock output.
114 LRCK O LR clock output.
115 SRCK O Bit clock output.
117~119 ADOUT(0~2) O Audio data output (0~2).
121 XPOWD I DAC power down control input.
122 VREFC I DAC reference voltage input for C signal.
123 IREFC I DAC bias current setting port for C signal.
124 COMPC I Capacitance connection for DAC (C signal) stabilization.
125 VCOUT O Unused.
126,136 AVDD - Analog supply voltage (+3.3V) for DAC.
127 VREFCB I DAC reference voltage input for CB signal.
128 IREFCB I DAC bias current setting port for CB signal.
129 COMPCB I Capacitance connection for DAC (CB signal) stabilization.
130 VCBOUT O Unused.
131,141 AVSS - Analog ground for DAC.
132 VREFCR I DAC reference voltage input for CR signal.
133 IREFCR I DAC bias current setting port for CR signal.
134 COMPCR I Capacitance connection for DAC (CR signal) stabilization.
135 VCROUT O Unused.
137 VREFY I DAC reference voltage input for Y signal.
138 IREFY I DAC bias current setting port for Y signal.
139 COMPY I Capacitance connection for DAC (Y signal) stabilization.
140 VYOUT O Unused.
143 XYSYNCO I/O Vertical synchronizing signal input/output.
144 XHSYNCO I/O Horizontal synchronizing signal input/output.
146 VCLK O Clock output for digital video data output.
148~155 VD0~VD7 O Digital video data output (0~7).
158,159,161,162
164,165,167,168
170,171,173,175
177,178,180,181
MDQ0~MDQ15 I/O SDRAM data bus (0~15).
183 MCKI I Clock input from SDRAM.
185 MCK O Clock output to SDRAM.
187 DQMLE O Lower bite data, mask signal of expander SDRAM.
189 DQMLM O Lower bite data, mask signal of main SDRAM.
190 DQMUE O Upper bite data, mask signal of expander SDRAM.
192 DQMUM O Upper bite data, mask signal of main SDRAM.
193 XWE O Write enable signal of SDRAM.
195 XCAS O CAS signal of SDRAM.
196 XRAS O RAS signal of SDRAM.
198 XCSE O Chip select signal of expander SDARM.
199 XCSM O Chip select signal of main SDARM.
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299

DV-5700/DVF-R9050/R9050-S
15
CIRCUIT DESCRIPTION
ODC, TS
Decoder etc.
Stream
Interface
Video
and
PLL 27MHz
Audio
Decoder
Stream
Parser
Sub- picture REC656
Decoder (Digital Video Out)
System Controller Host Video
(Microprocessor) Interface Interface DAC Y/Y
NTSC/PAL DAC Cb/Composite
Memory Encoder DAC Cr
SDRAM Interface Audio DAC C/C
(16bit) Interface Audio Out
(DAC for Audio)
CD-DA
IEC958
Port No. Port Name I/O Function
External OSD Interface
1~5 OSDC(0~4) Multiplexed chroma signal is input on this bus.
156~160 OSDC(5~9) I (Connected to ground.)
6 OSDSEL - External OSD select input. (Connected to ground.)
144~153 OSDY(0~9) - External OSD luma input. (Connected to ground.)
Test outputs(Not shown on Block diagram)
7~10 TEST(03~06)
13~15 TEST(00~02) O Test outputs. These pins should be left unconnected for normal operation.
Test inputs(Not shown on Block diagram)
19 TESTB I Active low test input. This pin should be tied to VDD for normal operation.
69,70,14 TEST (0~2) I Active high test inputs. This pin should all be tied to VSS for normal operation.
Power Supply Connections(Not shown on Block diagram)
11,28,40,49,59
60,81,87,93,99
101,107, 113,119 VDD - Digital power connections. Connect to the digital +3.3 volt power supply
121,127,131,135 and decouple to the digital ground plane.
141,154
12,29,41,50,79
80,82,88,94,100
102,108,114,120 VSS - Digital ground connections. Connect to the digital ground plane.
122, 128,132,136
142,155
72 ISINK - Analog current sink return for the video DAC circuits.
Connect to the analog ground plane.
68 AVDD - Analog power connections for the clock PLL circuits.
74 AVDD - Analog power connections for the video DAC circuits.
Control Signals
16 SDA I I2C compatible serial control bus data.
17 SCL I/O I2C compatible serial control bus clock.
18,20 MODE(0,1) - I2C operating MODE(0,1).
21~23 ADDR(0~2) - The setting of ADDR(0~2) allow the I2C address of the device to be programmed
to prevent conflict with the other I2C devices in the system.
7. Digital Video Enhancer : FL12220 (X35, IC703)
7-1 Port Function
6-2 Block Diagram
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299

DV-5700/DVF-R9050/R9050-S
16
CIRCUIT DESCRIPTION
Port No. Port Name I/O Function
24 I2CCLK I Clock input for the internal I2C circuit.
25 RESETB I Reset. When this input is set low it will reset all internal registers
to the default states.
67 CLKIN I Master clock input.
139 ENHOFF - When this pin is set low the FL12220 will be in normal enhancement mode.
Input Signals
26,27,30~37 CBIN(0~9) I 10-bit non-multiplexed Cb or multiplexed Cb/ Cr signal input bus.
43~48,51~54 CRIN(0~9) I 10-bit non-multiplexed Cr signal input bus.
55~58,61~66 YIN(0~9) I 10bit luminance or multiplexed Y/Cb/Cr signal input bus.
Input Signals(cont.)
38 HBLANKI I Horizontal input blanking signal.
39 VBLANKI I Vertical input blanking signal.
42 FLDIN I Odd/Even field designator input.
Analog Output Signals
71 R/Cr-ANA O Analog output.
73 G/Y-ANA O Analog output.
75 B/Cb-ANA O Analog output.
76 COMP - Compensation for video DACs. Should be connected to analog
ground via a capcitor.
77 RSET - Current setting resistor for video DACs.
78 VREF - Voltage reference for video DACs.
Digital Output Signals
83~86,89~92
95,96 G/YOUT(0~9) O Green or luminance output bus.
115~118
123~126,129,130 CBOUT(0~9) O Blue or Cb chrominance output bus.
Digital Output Signals(cont.)
97,98,103~106
109~112 CROUT(0~9) O Red or Cr chrominance output bus.
133 HBLANKO O Horizontal output blanking signal.
134 VBLANKO O Vertical output blanking signal.
137 YCLKO O Output luma sampling clock.
138 FLDO I Odd/Even field designator input.
140 CCLKO O Output chroma sampling clock.
HREFI
VREFI Sync & Timing Luma Triple
FLDIN Control Large- Edge 10-bit
CLKIN Enhancer DAC
Analog
30 Input YUV /RGB
Formatter Interpolator Color-Space
Digital Luma Converter 30
YUV/ Ycr
Cb Detail
Enhancer
& Output
Formatter Digital
Line YUV YCrCb/
Memories RGB
SCL
I 2CControl Chroma Decimator OSD
SDA
Interface Registers
Large-Edge
Enhancer (Optional) Engine &
Interface External
OSD
7-2 Simplified Block Diagram
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299

DV-5700/DVF-R9050/R9050-S
17
CIRCUIT DESCRIPTION
Port No. Port Name I/O Function
Test outputs
112,113 TEST(00, 01) O These pins are test outputs and should be left unconnected in
normal operation.
Test inputs
41,50,51,108 TEST(0~5) - These pins are used for test purposes only and should always
109,111 be tied low for normal operation.
Power Supply Connections(Not shown on Block diagram)
1,33,63,73,84, Pad Ring digital power connections. Connect to the digital +3.3
95,105,114,123, VDD33 - volt power supply and decouple to the digital ground plane.
137,144,151,167
2,17,34,55,64,
74,85,96,106, VSS - Ground connections. Connect to the digital ground plane.
115,124,132,138,
145,152,159,168
43 AVSS - Ground connection for the clock PLL circuits.
Connect to the digital ground plane.
16,54,107,158 AVDD25 - Core Logic digital power connections. Connect to the digital +2.5 volt power
supply and decouple to the digital ground plane.
Analog power connections for the clock PLL circuit.
42 AVDD - Connect to a separately decoupled +2.5 volt power supply and decouple
directly to the AVSS pin.
Control Signals
49 RESETB I Reset. When this input is set low it will reset all the internal registers
to the default states.
When this pin is set high the outputs of the FL12200 will be enabled ; when
53 OE O it is set low the outputs will be set into a high-impedance state.
56~58 IFORMAT(2~0) I Input signal format control.
59~61 OFORMAT(2~0) O Output signal format control.
The settings of DADDR(1,0) allow the device address of the control
44,45 DADDR(1,0) - bus to be programmed to prevent conflict with the other devices
connected to the bus.
When this pin is set low the control bus will operate in the slave mode
46 MODE - ; allowing the device to programmed from an external controller.
47 SDA I 2-wire serial control bus data.
48 SCL I/O 2-wire serial control bus clock.
40 PIXCLK I Pixel clock input. This clock is used to drive all the circuits in the FL12200.
62 N/P/IN/OUT I/O NTSC/PAL input or output.
Control Signals(contd.)
52 NOMEM I No memory mode control input.
Input Signals
18~27 G/YIN(0~9) I 10-bit green or luminance signal input bus.
6~15 B/CbIN(0~9) I 10-bit blue or Cb chroma signal input bus.
28~32 R/CrIN(0~4) I 10-bit red or Cr chroma signal input bus.
35~39 R/CrIN(5~9)
3 HSYNCREFI I Horizontal sync or reference.
4 VSYNCREFI I Vertical sync or reference.
5 FIELDIN I Field identifier input.
Output Signals
65~72 G/YOUT(2~9) O Green or luminance output bus.
75,76 G/YOUT0,1
93,94 B/CbOUT8,9 O Blue or Cb chrominance output bus.
97~104 B/CbOUT(0~7)
8. Video Deinterlacer : FL12200(X35, IC700)
8-1 Port Function
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299

DV-5700/DVF-R9050/R9050-S
18
CIRCUIT DESCRIPTION
Ext. Syncs /
PIXCLK PLL/Clock
Generator
Sync
Generator Sync Out
RGB/YUV/
YCrCb/D1
10
/
/
/
Input
Signal
Formatter
Deinterlacer Core with DCDiTM , Motion
Compensation, Film Mode Detection
and Bad Edit Correction
Output
Signal
Formatter
10
/
/
/
YU V
/RGB/
YCrCb
DADDR
SDA
SCL
2
/Control
Interface and
Registers
Port No. Port Name I/O Function
77~83 R/CrOUT(3~9) O Red or Cr chrominance output bus.
86~88 R/CrOUT(0~2)
116 CCLKO O Chroma output sampling clock.
117 YCLKO O Luma output sampling clock.
89 VREFO - Start of active field or frame indicator.
90 HREFO O Start of active line indicator output.
91 VSYNC/CREFO O Vertical sync output. This signal provides the vertical sync
function for the outputs.
92 H/CSYNCO O Horizontal or composite sync output. This signal provides the
horizontal sync function for the outputs.
110 FILM O Film mode detector output.
SDRAM Interface Signals
125~131 ADDR(4~10) -SDRAM address bus. This signal bus is used to address the
133~136 ADDR(0~3) external SDARM(s) used for field memories.
139~143,146~150 DATA(0~4) SDRAM data bus. This signal bus is used to transfer the data
153~157,160~166 5~9,10~14, - to and from the external SDRAM(s) used for field memories.
169~176 15~21,22~29
118 MEMCLKO O SDRAM clock and 2x output sampling clock.
119 WEN - SDRAM write enable. This active low signal should be connected
to the WE pin(s) on the SDRAM(s).
120 RASN - SDRAM row address select. This active low signal should be connected
to the RAS pin(s) on the SDRAM(s).
121 CASN - SDRAM column address select. This active low signal should be
connected to the CAS pin(s) on the SDRAM(s).
122 BSEL - SDRAM bank select.
8-2 Simplified Block Diagram
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299

DV-5700/DVF-R9050/R9050-S
19
CIRCUIT DESCRIPTION
Port No. Port Name I/O Function
1 BCK I Audio data bit clock input.
2 DATA I Audio data digital input.
3 LRCK I L-ch/R-ch audio data latch enable input.
4 DGND - Digital ground.
5 VDD - Digital power supply (+3.3v).
6 VCC - Analog power supply (+5.0V).
7 VOUTL O Analog output for L-ch.
8 VOUTR O Analog output for R-ch.
9 AGND - Analog ground.
10 VCOM - Common voltage decoupling.
11 ZEROR/ZEROA O Zero flag output for R-ch / Zero flag output for L/R-ch.
12 ZEROL/NA O Zero flag output for L-ch / No assign.
13 MD I Mode control data input.
14 MC I Mode control clock input.
15 ML I Mode control latch input.
16 SCL I System clock input.
9. Port Function of 2ch DAC : PCM1748E (X25, IC204)
Port No. Port Name I/O Function
1~6 ZERO1~6 O Zero data flag for Vout 1~6. Can also be used as GPO pin.(Unused)
/GPO1~6
7 NC - Analog ground.
8 NC - Analog power supply (+5.0V).
9 VOUT6 O Voltage output for audio signal corresponding to Rch on data3. Up to 96 kHz
10 VOUT5 O Voltage output for audio signal corresponding to Lch on data3. Up to 96 kHz
11 VOUT4 O Voltage output for audio signal corresponding to Rch on data2. Up to 96 kHz
12 VOUT3 O Voltage output for audio signal corresponding to Lch on data2. Up to 96 kHz
13 VOUT2 O Voltage output for audio signal corresponding to Rch on data1. Up to 192 kHz
14 VOUT1 O Voltage output for audio signal corresponding to Lch on data1. Up to 192 kHz
15 VCOM O Common voltage output.
16 NC - Analog ground.
17 AGND5 - Analog ground.
18 VCC5 - Analog power supply (+5.0V).
19 AGND6 - Analog ground.
20 NC - Analog power supply (+5.0V).
21 AGND4 - Analog ground.
22 VCC4 - Analog power supply (+5.0V).
23 AGND3 - Analog ground.
24 VCC3 - Analog power supply (+5.0V).
25 AGNG2 - Analog ground.
26 VCC2 - Analog power supply (+5.0V).
27 AGND1 - Analog ground.
28 VCC1 - Analog power supply (+5.0V).
29 NC - Analog ground.
30 NC - Analog power supply (+5.0V).
31,32 NC - Analog ground.
33 MDO O Serial data output for function register control port. (Unused)
34 MDI I Serial data input for function register control port.
35 MC I Shift clock for function register control port.
36 ML I Latch enable for function register control port.
37 RST I System reset input. (Active low)
38 SCKI I System clock input. Input frequency is 128, 192, 256, 384, 512 or 768fs.
10. Port Function of 6ch DAC : PCM1602KY (X25, IC205)
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299

DV-5700/DVF-R9050/R9050-S
20
CIRCUIT DESCRIPTION
DVF-R9050 Audio Output Block Diagram
* SCART terminals (AV1,2) are available for European model only.
IC212
IC204 SW1 A
DMIX 2ch L.P.F.
DAC 60k MUTE MIX
AOUT0 IC901 B
DRIVE L2CH
X35 IC205
H : 60k L : 110k
-229 L.P.F.
AOUT1 IC902 MUTE FL. FR
DRIVE 6ch 60k/110k
L.P.F. L.P.F.
AOUT2 IC903 DAC 60k
100kHz
MUTE SL. SR
DRIVE IC801 SW2
L.P.F.
L.P.F. SW 60k MUTE C. SW
Serial- H2CH
Parallel MUTE AV1
CONTROL
IC224 BUSS L : Buss Management AV2
X25-646 H : Through
E TYPE ONLY
Media vs Switches
Low Pass Filter Media Media SW1
110kHz DVD-Audio(fs : 192kHz, 176.4kHz) DVD-Audio(fs : 192kHz, 176.4kHz) B
60kHz All VCD, CD-DA
Others A
KEY 0 (Pin2 ) KEY 1 (Pin3 ) KEY 2 (Pin4 )
OP/CL PLAY
SKIP DISC 1 STOP
AOP DISC 2 SKIP DOWN
DISC 3 SKIP UP
DISC 4 PAUSE
DISC 5
11. Key Matrix
The number inside ( ) is pin number of main u-com (X25, IC1).
Port No. Port Name I/O Function
38 SCKI I System clock input. Input frequency is 128, 192, 256, 384, 512 or 768fs.
39 SCKO O Buffered clock output. (Unused)
40 BCK I Shift clock input for serial audio data.
41 LRCK I Left and right clock input. This clock is equal to the sampling rate, fs.
42 TEST - Test pin.
43 VDD - Digital power supply (+3.3V).
44 DGND - Digital ground for +3.3V.
45 DATA1 I Serial audio data input for Vout1 and Vout2.
46 DATA 2 I Serial audio data input for Vout3 and Vout4.
47 DATA 3 I Serial audio data input for Vout5 and Vout6.
48 ZEROA O Zero data flag. Logical "AND" of ZERO1 through ZERO6.
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299