KEPCO DIN MRW-160P User manual

©2000, KEPCO, INC 1
Data subject to change without notice 228-1405
INSTRUCTION MANUAL
KIT
KEPCO
KEPCO, INC. " 131-38 SANFORD AVENUE " FLUSHING, NY. 11352 U.S.A. " TEL [phone] " FAX [phone]
http://www.kepcopower.com " email: [e-mail]
An ISO 9001 Company.
DIN MRW-150P,
-160P, -170P
DIN-RAIL MOUNTING KIT
FOR SERIES MRW 150/151KV, 160/161KV, 170/171KV
DESCRIPTION. Kepco KITs, Models DIN MRW-150P, MRW-160P and MRW-170P each contain a cover, a cable kit, a
mounting bracket with left and right preassembled mounting clips and associated hardware used to install MRW Series
power supplies on a DIN rail. The -150P suffix is for the 35 Watt MRW 150/151KV models. The -160P suffix is for the
50 Watt 160/161KV models. The -170P suffix is for the 65 Watt MRW 170/171KV models. The “P” suffix is for mount-
ing the power supply perpendicular to the DIN rail as shown in Figure 1. Outline Dimensions are shown in Figure 5
FIGURE 1. P SUFFIX ORIENTATION
TABLE 1. COMPONENTS SUPPLIED
KIT
MODEL NO.
CABLE
KIT
PART
NO.
COVER
PART
NO.
MOUNTING
BRACKET
PART NO.
SCREW
(QTY 4)
(Power Supply
To Mounting
Bracket)
PART NO.
WASHER
(QTY 4)
(Power Supply
To Mounting
Bracket)
PART NO.
CLIP
(QTY 2)
PART
NO.
CLIP
PLATE
(QTY 2)
PART
NO.
SCREW
Thread-form
(QTY 4)
(Clip To
Mounting
Bracket)
PART NO.
WASHER
(QTY 4)
(Clip To
Mounting
Bracket)
PART NO.
DIN MRW-150P 219-0184 CA 19
128-2048
101-0383
(8-32 X 3/16
PHPH)
103-0017
(NO. 8, INT.
TOOTH)
108-0362 128-1938
101-0443
(4-40 X 1/4
BHPH)
103-0014
(NO. 4, INT.
TOOTH)
DIN MRW-160P 219-0184 CA 20
DIN MRW-170P 219-0239 CA 20

2228-1405 061901
KEPCO, INC. " 131-38 SANFORD AVENUE " FLUSHING, NY. 11352 U.S.A. " TEL [phone] " FAX [phone]
http://www.kepcopower.com " email: [e-mail]
INSTALLATION
1. INSTALL COVER. Attach the cover to the power supply per instruction manual supplied with the cover.
2. INSTALL MOUNTING BRACKET. Attach the mounting bracket to the power supply using the hardware
supplied (see Figure 2).
FIGURE 2. INSTALLING MOUNTING BRACKET ON POWER SUPPLY
3. INSTALL CLIPS. Attach preassembled mounting clips into the mounting bracket holes using hardware
supplied (see Figure 3).
FIGURE 3. INSTALLING CLIPS ON MOUNTING BRACKET

061901 228-1405 3
KEPCO, INC. " 131-38 SANFORD AVENUE " FLUSHING, NY. 11352 U.S.A. " TEL [phone] " FAX [phone]
http://www.kepcopower.com " email: [email protected]
4. INSTALL CABLE KIT. Attach wires to the power supply per Instruction Sheet supplied with cable kit.
5. INSTALL POWER SUPPLY ON DIN RAIL. To mount the power supply on the rail insert one end of both
mounting clips under one edge of the rail, then snap the other end of the two clips into place (see Figure 4A).
FIGURE 4. INSTALLATION AND REMOVAL OF POWER SUPPLY FROM DIN RAIL
REMOVING POWER SUPPLY FROM DIN RAIL. While grasping the power supply with one hand, Insert a screwdriver
into the access holes provided and apply leverage towards the left as shown in Figure 4B to disengage each clip from
the rail. Where mounting clips are close together, it may be necessary to apply leverage with two screwdrivers simul-
taneously.
BREMOVAL
INSTALLATION
A

4228-1405 061901
KEPCO, INC. " 131-38 SANFORD AVENUE " FLUSHING, NY. 11352 U.S.A. " TEL [phone] " FAX [phone]
http://www.kepcopower.com " email: [e-mail]
FIGURE 5. MRW 35W/50W/65W POWER SUPPLY WITH KIT INSTALLED, OUTLINE DIMENSIONS