Kerio Control NG100W User manual

Kerio Control
NG100W, NG300W

Kerio Control NG100W, NG300W
2
1 Purpose
This document is a quick guide for safely installing and implementing Kerio Control NG100W
and NG300W UTM appliances.
2 General Safety Instructions
During installation follow these security instructions:
•Theapplianceshouldbeplacedonaatsurfaceorsecurelymountedhorizontallyinrack
enclosure.
• Do not attempt to open or disassemble the appliance for any reason.
• Strictly follow the installation instructions (see section 4).
• Do not place the appliance near a heat source.
• Place the appliance in a ventilated space, making sure that the appliance fans and vents are
unobstructed at all times.
• Do not expose the appliance to liquids of any kind. In the event of liquid intrusion, unplug
the appliance immediately.
• Verify that the voltage and frequency of the power socket matches the values printed on
the power adapter before plugging in the appliance. Use only the power adapter supplied
with the appliance.
• Do not place any items on top of the power cable; keep the power cable away from walk-
waysorotherareaswhereitcouldposeatrippinghazard.
3 Appliance Description
Kerio Control hardware appliance types:
•KerioControlNG100W—Desktopappliance—seegure1.
•KerioControlNG300W—Sub-1Utablemountableappliance—seegure2.
Feature Description
Serial port Used for connecting to a console with a serial cable
USB ports Input for USB devices
Ethernet network ports Used for connecting to the Internet and the LAN with an
Ethernet cable
Antenna(s) Dual band antenna used for Wi-Fi
Table 1 Kerio Control Hardware Appliance Features
Figure 1 Kerio Control NG100W (front + back)
Ethernet Ports
USB Ports
Serial PortPower Switch HDMI Port
Wi-Fi Antenna

3
Figure 2 Kerio Control NG300W (front + back)
4 Kerio Control Hardware Appliance Installation and Conguration
Once a suitable place has been located for the appliance and it has been plugged into a power
outletaccordingtothesafetyinstructions,itistimetoconnectittothenetworkandcongure
settings.
Figure 4 Connecting Kerio Control NG100W to the network
Figure 5 Connecting Kerio Control NG300W to the network
Toconguretheappliance:
1. Connect the antenna(s) to the hardware appliance.
2. Connect the Internet port to the Internet (e.g. DSL or Cable modem) using an Ethernet
cable.
3. ConnecttheLANporttothecomputerthatwillbeusedtoconguretheappliance(see
theguresbelow).
4. Turn on the appliance.
ENQuick Installation Guide
Ethernet Ports USB PortsSerial Port
Wi-Fi Antennas

© 2016 Kerio Technologies s.r.o. All rights reserved. www.kerio.com
Now you have two options:
• Add and manage the appliance through MyKerio (see http://kb.kerio.com/1846)
• Access the Kerio Control Administration through a browser (see below):
1. Set the networking preferences for Ethernet on the connected computer to “Automatic
DHCPconguration”.(Youcanchangeitlaterafterthecongurationiscomplete).
2. RenewtheDHCPleaseonthecomputerandconrmithasanIPaddressof10.10.10.11
3. Open a web browser and connect to the Kerio Control Administration web interface us-
ing the following URL:
https://10.10.10.1/admin
4. IgnoretheSSLcerticatewarningsandproceedtothecongurationwizard.
5. Followtheinstructionsprovidedbythewizardandconguretheappliance.
See http://kb.kerio.com
Note: For troubleshooting purposes, you can use the serial port to connect the console to the
appliance. See http://kb.kerio.com/1875 for details.
5 Additional Information
Forfurtherassistancewithcongurationpleaserefertoadditionaldocumentationat:
• http://kb.kerio.com/category/kerio-control/
For online and community based support resources please visit :
• http://www.kerio.com/support