KGEAR GCF8S User manual

1
2
3
4
5
6
Installation
The loudspeaker can be installed both on the ceiling and
on a vertical surface. It is strongly recommended that the
mounting surface is flat (not curved).
Ensure that the mounting surface is free from
obstructions, pipes or studs, either in front
and behind the surface.
The cable runs and cable pipes shall be
set according to the loudspeaker system
configuration. The cables must be of
adequate quality, suitable for the installation’s
environmental conditions and with proper
copper section to minimize power loss.
GCF8S / GWF8S
Remove the grill from the loudspeaker and keep it
in a safe place.
Position the cutout template and mark the surface
accordingly.
Drill a pilot hole, then cut all of the way around the
circular outline with a cutting saw.
Pull the speaker wire out of the hole and connect
it to the loudspeaker.
Insert the loudspeaker into the hole and tighten all
the clamp screws with a Phillips #1 screwdriver.
Reposition the grill on the loudspeaker.
8"ceiling/in-wall subwoofer
4x Phillips
screws

•20211110•
6 mm
(0.25 in)
12 mm
(0.5 in)
Amplifier
Wire terminals
Loudspeaker
+
–
Loudspeaker
terminals
IN OUT
Type
Transducers
Frequency Response
Sensitivity
Max SPL 1
Coverage
Power Handling
Nominal Impedance
Dimensions ( outer [ inner] x H)
Minimum required mounting depth
Cutout diameter
Weight
IP rating
• Read these instructions.
• Keep these instructions.
• Heed all warnings.
• Follow all instructions.
• Installation and commissioning
may only be carried out by
qualified and authorized
personnel.
• Do not use this apparatus near
water.
• Do not install near any heat
sources such as radiators,
heat registers, stoves, or other
apparatus (including amplifiers)
that produce heat.
• Only use attachments/
accessories specified by the
manufacturer.
• Do not expose this apparatus to
dripping or splashing and ensure
that no objects filled with liquids,
such as vases, are placed on this
apparatus.
• Prior to installing the speakers
into any ceiling/wall, check the
structure for weight bearing
ability and avoid contact with any
wiring or plumbing that might be
behind the surface area.
Warning. Failure to follow these safety instructions
could result in fire, shock or other injury or damage to
the device or other property.
This device is in compliance with applicable CE
standards and regulations. Before putting the device
into operation, please observe the respective country-
specific regulations!
IMPORTANT SAFETY INSTRUCTIONS
• Installing on soft materials or in
areas incapable of supporting
the speakers’ weight may cause
personal injury or damage to the
speaker.
• Make sure the speaker is properly
secured to the ceiling/wall. Please
use the proper screws, bolts, or
anchors. Failure to do so may
cause the speaker to become
unsecured and cause potential
damages/injuries.
• Damage to the woofer and
tweeter may occur if the speaker
is dropped or hit, resulting in no
sound or distorted sound.
• Never overdrive your speakers to
the point of distortion and always
reduce volume prior to switching
input sources.
• Use only approved and certified
wiring in your installation, do
not stretch or place the wire in
contact with sharp objects.
• Prior to removing cables ensure
all power to your amplifier and
other components is turned off.
GCF8S / GWF8S
Thank you for choosing this KGEAR product!
To ensure proper operation, please carefully read this
owner’s manual and safety instruction before using the
product.
After reading this manual, be sure to keep it for future
reference.
Packing List
Upon arrival, carefully
inspect the shipping
carton, then examine and
test your new amplifier.
If you find any damage,
immediately notify the
shipping company. Check
that the following parts are
supplied with the product.
Loudspeaker Wiring
Ensure that the amplifier is unplugged from the mains
before making any connections.
Connect the input terminals of the loudspeakers to the
speaker output terminals of the amplifier. Always check
to ensure polarity is correct: L(left) to L, R(right) to R,
“+” to “+”, and “-” to “-”.
Note: In case of sonic artifacts, roughness or distortion,
reduce the signal volume to a lower setting. Never allow
the amplifier to be driven into “clipping”. Damage caused
by operating the speakers at distorted volume levels is
not covered by the warranty.
• 8" subwoofer
• Circular or square
grill according to the
speaker model
• Cutout template
• This user guide
GCF8S
GWF8S
8 ” Ceiling/In-Wall
Subwoofer
Lo-Z 8Ω
Technical specifications
Passive subwoofer
8" Woven Glass Fiber woofer
40 Hz – 250 Hz (-10 dB)
90 dB (1 W, 1 m)
110 dB (peak)
180°
GCF8S / GWF8S
80 W
8 Ω
Handling & Finishes
277 [258] x 105 mm ( 10.9 [10.1] x 4.1 in)
112 mm (4.4 in)
258 mm ( 10.1 in)
2,04 kg (4.5 lb)
IP54
BLACK GCF8S GWF8S
WHITE GCF8SW GWF8SW
1 Maximum SPL is calculated using a signal with
crest factor 4 (12dB) measured at 1 m.