KidKraft Cedar Summit Adventure Ridge Playset User manual

INSTALLATION AND OPERATING INSTRUCTIONS
ADVENTURE RIDGE PLAYSET - F25730EX
Rev 09/06/2018
Table of Contents
Warnings and Safe Play Instructions .............pg. 2
Protective Surfacing Guidelines. . . . . . . . . . . . . . . . . .pg. 3
Instructions for Proper Maintenance ............pg. 4
About Our Wood – Limited Warranty ............pg. 5
Keys to Assembly Success .......................pg. 6
Part ID ..........................................pg. 8
Step-By-Step Instructions ..................... pg. 19
Installation of I.D./Warning Plaque .........Final Step
OBSTACLE FREE SAFETY ZONE -33’2” x 30’10” (10.3 x 9.4 m) area requires Protecve Surfacing. See page 3.
MAXIMUM VERTICAL FALL HEIGHT - 6’ 7” (2.01 m)
CAPACITY - 15 Users Maximum, Ages 3 to 10; Weight Limit 110 lbs. (49.9 kg) per child.
RESIDENTIAL HOME USE ONLY. Not intended for public areas such as mul-unit residences, schools,
churches, nurseries, day cares or parks.
Warning. Only for domesc use.
WARNING
Cedar Summit by KidKraft
4630 Olin Road
Dallas, TX 75244, United States
[e-mail]
Online Parts Replacement:
Cedarsummitplay.com/parts-center-warranty-claim
Customer Service:
1(800) 933-0771 or [phone]
KidKraft Netherlands BV
Olympisch Stadion 29
1076DE Amsterdam, The Netherlands
Europe Customer Service: [phone]
[e-mail]
EU Online Parts Replacement: parts.kidkraft.eu
5.4m
6.3m
9.4m
10.3m
10 - 12 Hrs
FOR FORT & SWING
TWO PERSON
ASSEMBLY
2-4 Hrs
10 - 12 Hrs
FOR FORT & SWING
TWO PERSON
ASSEMBLY
10 - 12 Hrs
FOR FORT & SWING
Approx. 2 Hrs
TUBE SLIDE
To reduce the risk of serious injury or death, you must
read and follow these instrucons. Keep and refer to these
instrucons oen and give them to any future owner of this
play set. Manufacturer contact informaon provided below.
By

Warnings and Safe Play Instructions
CONTINUOUS ADULT SUPERVISION REQUIRED. Most serious injuries and deaths on playground equipment have occurred
while children were unsupervised! Our products are designed to meet mandatory and voluntary safety standards. Complying
with all warnings and recommendations in these instructions will reduce the risk of serious or fatal injury to children using
this play system. Go over the warnings and safe play instructions regularly with your children and make certain that they
understand and follow them. Remember on-site adult supervision is required for children of all ages.
eeS . tes-yalp ruoy fo snoi tat imi l yt icapac evresb O
front cover.
gnisolcne toof l luf dna gni t tfi llew htiw nerd li hc sserD
footwear.
retne c eht ni thgiew lluf rieht hti w tis ot nerdlihc hc a eT
of the swing seat to prevent erratic swing motion or
falling off.
, gn issim ;doow dekca rc ro nekorb , dere tnil ps rof kcehC
loose, or sharp edged hardware. Replace, tighten and or
sand smooth as required prior to playing.
niahc ,sreddal epor ,sepor gnibmi lc dednepsus taht yf i reV
or cable are secured at both ends and cannot be looped
back on itself as to create an entanglement hazard.
rehto dna edils eht k c ehc ,s y ad toh ro dna ynnus nO
plastic rides to assure that they are not very hot as to
cause burns. Cool hot slide and rides with water and wipe
dry prior to using.
ra ewtoof le eh ro eot nepo ra ew ot nerdl ihc wolla ton oD
like sandals, flip–flops or clogs.
dniheb ,neewteb , tnorf ni ,klaw ot nerdl ihc wol la ton oD
or close to moving rides.
pool ro sepor ro sniahc gniws tsiwt nerdl ihc tel ton oD
them over the top support bar. This may reduce the
strength of the chain or rope and cause premature failure.
.noi to m ni era yeht el ihw sedi r f fo teg nerdl ihc tel ton oD
.tew si ti nehw tnempiuqe no gnibmilc timrep ton oD
a ni tnempiuqe fo esu ro yalp hguor t im rep ton oD
manner for which it was not intended. Standing on or
jumping from the roof, elevated platforms, swings,
climbers, ladders or slide can be dangerous.
.staes ro sedi r ytpme gniws ot nerdl ihc w ol la ton oD
ro tsrfi
daeh edi ls nwod og ot nerdl ihc wol la ton oD
run up slide.
SERIOUS HEAD INJURY HAZARD
Installation over concrete, asphalt, dirt, grass, carpet
and other hard surface creates a risk of serious injury
or death from falls to the ground. Install and maintain
shock absorbing material under and around play-set as
recommended on page 3 of these instructions.
COLLISION HAZARD
Place play-set on level ground at least 2m from any
obstruction such as a garage or house, fences, poles,
trees, sidewalks, walls, landscape timbers, rocks,
pavement, planters, garden borders, overhanging
branches, laundry lines, and electrical wires. (See
OBSTACLE FREE SAFETY ZONE on cover)
CHOKING HAZARD/SHARP EDGES & POINTS
Adult assembly required. This product contains small
parts and parts with sharp edges and points. Keep parts
away from children until fully assembled.
WARNING LABEL
Owners shall be responsible for maintaining the legibility
of the warning labels.
STRANGULATION HAZARD
,seni lsehtolc ,sepor ht iw yalp ot nerdl ihc w ol la REVEN •
pet leashes, cables, chains or cord-like items when using
this play-set or to attach these items to play-set.
ponchos, hoods, scarves, capes, necklaces, items with
draw-strings, cords or ties when using this play-set.
ste mleh trops ro ekib raew ot nerdl ihc wol la REVEN •
when using this play-set.
Failure to prohibit these items, even helmets with chin
straps, increases the risk of serious injury and death to
children from entanglement and strangulation.
TIP OVER HAZARD
Choose a level location for the equipment. This can reduce
the likelihood of the play set tipping over and loose-fill
surfacing materials washing away during heavy rains.
DO NOT allow children to play on the play-set until the
assembly is complete and the unit is properly anchored.
WARNING
WARNING – Safe Play Instructions
Orientate slide such that it gets the least amount of exposure
to the sun.
2

One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing
protective surfacing under and around your play equipment. The protective surfacing should be applied to a depth that is suitable
for the equipment height in accordance with ASTM F1292. There are different types of surfacing to choose from; whichever
product you select, follow these guidelines:
Loose-Fill Materials
•Maintain a minimum depth of 9 inches of loose-fill materials such as wood mulch/chips, engineered wood fiber (EWF), or
shredded/recycled rubber mulch for equipment up to 8 feet high; and 9 inches of sand or pea gravel for equipment up to 5 feet
high. NOTE: An initial fill level of 12 inches will compress to about a 9-inch depth of surfacing over time. The surfacing will also
compact, displace, and settle, and should be periodically raked and refilled to maintain at least a 9-inch depth.
•Use a minimum of 6 inches of protective surfacing for play equipment less than 4 feet in height. If maintained properly, this
should be adequate. (At depths less than 6 inches, the protective material is too easily displaced or compacted.)
NOTE: Do not install home playground equipment over concrete, asphalt, or any other hard surface. A fall onto a hard surface
can result in serious injury to the equipment user. Grass and dirt are not considered protective surfacing because wear and
environmental factors can reduce their shock absorbing effectiveness. Carpeting and thin mats are not adequate protective
surfacing. Ground level equipment -- such as a sandbox, activity wall, playhouse or other equipment that has no elevated play
surface -- does not need any protective surfacing.
•Use containment, such as digging out around the perimeter and/or lining the perimeter with landscape edging. Don’t forget to
account for water drainage.
•Periodically rake, check and maintain the depth of the loose-fill surfacing material. Marking the correct depth on the play
equipment support posts will help you to see when the material has settled and needs to be raked and or replenished. Be sure to
rake and evenly redistribute the surfacing in heavily used areas.
•Do not install loose fill surfacing over hard surfaces such as concrete or asphalt.
Poured-In-Place Surfaces or Pre-Manufactured Rubber Tiles
You may be interested in using surfacing other than loose-fill materials - like rubber tiles or poured-in-place surfaces.
•Installations of these surfaces generally require a professional and are not “do-it yourself” projects.
•Review surface specifications before purchasing this type of surfacing. Ask the installer/manufacturer for a report showing that
the product has been tested to the following safety standard: ASTM F1292 Standard Specification for Impact Attenuation of
Surfacing Materials within the Use Zone of Playground Equipment. This report should show the specific height for which the
surface is intended to protect against serious head injury. This height should be equal to or greater than the fall height - vertical
distance between a designated play surface (elevated surface for standing, sitting, or climbing) and the protective surfacing
below - of your play equipment.
•Check the protective surfacing frequently for wear.
Placement
Proper placement and maintenance of protective surfacing is essential. Refer to diagram on front cover. Be sure to;
•Extend surfacing at least  from the equipment in all directions.
•For to-fro swings, extend protective surfacing in front of and behind the swing to a distance equal to twice the height of the top bar
from which the swing is suspended.
•For tire swings, extend surfacing in a circle whose radius is equal to the height of the suspending chain or rope, plus 6 feet in all
directions.
From the CPSC Outdoor Home Playground Safety Handbook. At http://www.playgroundregs.com/resources/CPSC%20324.pdf
Protective Surfacing - Reducing Risk of Serious Head Injury From Falls.
2H 2H
H
Denotes Use Zone with Protective Surfacing
Use Zone for Single-Axis Swings
6 ft.
6 ft.
6 ft.
6 ft.
Denotes Use Zone with Protective Surfacing
Use Zone for Multi-Axis Swings
6 ft. 6 ft.
6 ft.
L
3

Instructions for Proper Maintenance
Your Cedar Summit Play System is designed and constructed of quality materials with your child’s safety in mind. As
with all outdoor products used by children, it will weather and wear. To maximize the enjoyment, safety and life of your
Play Set, it is important that you, the owner, properly maintain it.
HARDWARE:
Check metal parts for rust. If found,
sand and repaint using a non-lead paint
complying with 16 CFR 1303.
Inspect and tighten all hardware. On
wood assemblies DO NOT OVER-
TIGHTEN as to cause crushing and
splintering of wood.
Check for sharp edges or protruding screw threads, add
washers if required.
SHOCK ABSORBING SURFACING:
C heck for foreign objects. Rake and check depth of loose
fill protective surfacing materials to prevent compaction and
maintain appropriate depth. Replace as necessary.
(See Protective Surfacing, page 3)
GROUND STAKES (ANCHORS):
C heck for looseness, damage or deterioration. Should firmly
anchor unit to ground during use. Re-secure and or replace,
if necessary.
SWING HANGERS:
C heck that bolts are secure and tight. Quick clips should be
completely closed and threaded clips screwed tight.
I f squeaking occurs lubricate bushings with oil or WD-40®.
SWINGS, ROPES AND RIDES:
R einstall if removed during cold season. Check all moving
parts including swing seats, ropes, chains and attachments
for wear, rust and other deterioration. Replace as needed.
C heck that ropes are tight, secure at both ends and cannot
loop back as to create an entrapment.
WOOD PARTS:
C heck all wood members for deterioration, structural
damage and splintering. Sand down splinters and replace
deteriorated wood members. As with all wood, some
checking and small cracks in grain is normal.
A pplying a water repellent or stain (water-based) on a yearly
basis is important maintenance to maintain maximum life
and performance of the product.
Check the following at the beginning of the play season:
HARDWARE:
I nspect for tightness. Must be firmly against, but not
crushing the wood. DO NOT OVER-TIGHTEN.
This will cause splintering of wood.
C heck for sharp edges or protruding screw threads.
Add washers if required.
SHOCK ABSORBING SURFACING:
R ake and check depth of loose fill protective surfacing
materials to prevent compaction and maintain appropriate
depth. Replace as necessary.
(See Protective Surfacing, page 3)
Check twice a month during play season:
SWING HANGERS:
C heck that they are secure and orientated correctly. Hook
should rotate freely and perpendicular to support beam.
If squeaking occurs lubricate bushings with oil or WD-40®.
SWINGS AND RIDES:
C heck swing seats, all ropes, chains and attachments for
fraying, wear, excessive corrosion or damage.
Replace if structurally damaged or deteriorated.
Check once a month during play season:
SWINGS AND RIDES:
T o prolong their life, remove swings and store inside when
outside temperature is below 32°F/0°C. Below freezing,
plastic parts may become more brittle.
SHOCK ABSORBING SURFACING:
R ake and check depth of loose fill protective surfacing
materials to prevent compaction and maintain appropriate
depth. Replace as necessary.
(See Protective Surfacing, page 3)
Check at the end of the play season:
If you dispose of your play set: Please disassemble and dispose of your unit so that it does not create any unreasonable
hazards at the time it is discarded. Be sure to follow your local waste ordinances.
If Bolt protrudes
beyond T-Nut
Use an extra
flat washer
4

About Our Wood
Cedar Summit Premium Play Systems uses only premium playset lumber, ensuring the safest product for your children’s
use. Although we take great care in selecting the best quality lumber available, wood is still a product of nature and susceptible to
weathering which can change the appearance of your set.
What causes weathering? Does it affect the strength of my Play System?
One of the main reasons for weathering is the effects of water (moisture); the moisture content of the wood at the surface is
different than the interior of the wood. As the climate changes, moisture moves in or out of the wood, causing tension which can
result in checking and or warping. You can expect the following due to weathering. These changes will not affect the strength of
the product:
1. Checking is surface cracks in the wood along the grain. A post (4” x 4”) will experience more checking than a board (1” x 4”)
because the surface and interior moisture content will vary more widely than in thinner wood.
2. Warping results from any distortion (twisting, cupping) from the original plane of the board and often happens from rapid
wetting and drying of the wood.
3. Fading happens as a natural change in the wood color as it is exposed to sun-light and will turn a grey over time.
How can I reduce the amount of weathering to my Play System?
At the factory we have coated the wood with a water repellent or stain. This coating decreases the amount of water absorption
during rain or snow thus decreasing the tension in the wood. Sunlight will break down the coating, applying a water repellant or
stain on a yearly basis is important maintenance. (see your local stain and paint supplier for a recommended product)
Most weathering is just the normal result of nature and will not affect safe play and enjoyment for your child. However if you are
concerned that a part has experienced a severe weathering problem please call our consumer relations department for further assistance.
warranty service.
province to province. This warranty excludes all consequential damages, however, some states do not allow the
limitation or exclusion of consequential damages, and therefore this limitation may not apply to you.
5 Year Limited Warranty
warrants that this product is free from defect in materials and workmanship
for a period of one year from the original date of purchase. In addition, lumber is warranted for 5
years against structural failure due to rot and insect damage. All other parts, such as hardware, swings,
rides, accessories, and slides carry a one-year warranty only.
This warranty applies to the original owner and registrant and is non-transferable.
Regular maintenance is required to assure the integrity of your Play System. Failure by the owner
to maintain the product according to the maintenance requirements may void this warranty. This
warranty does not cover any inspection cost.
This Limited Warranty does not cover:
• Labour for replacement of any defective item(s);
•Incidental or consequential damages;
•Cosmetic defects which do not affect performance or integrity;
•Vandalism; improper use or installation; acts of nature;
• Minor twisting, warping, checking, or any other natural occurring properties of wood that do not
affect performance or integrity.
Cedar Summit by KidKraft products have been designed for safety and quality. Any modifications
made to the original product could damage the structural integrity of the unit leading to failure and
possible injury. Cedar Summit by KidKraft cannot assume any responsibility for modified products.
Furthermore, modification voids any and all warranties.
This product is warranted for RESIDENTIAL USE ONLY. Under no circumstance should a Cedar Summit
Play System be used in public settings such as schools, churches, playgrounds, parks, day cares
and the like. Such use may lead to product failure and potential injury. Any and all public use will void this
warranty.
Cedar Summit by KidKraft disclaims all other representations and warranties of any kind, express or implied.
5

This identifies information that requires special
attention. Improper assembly could lead to an unsafe
or dangerous condition.
Where this is shown, 2 or 3 people
are required to safely complete the
step. To avoid injury or damage
to the assembly make sure to get
help!
Check that assembly is square
before tightening bolts.
Use a measuring tape to assure
proper location.
Check that set or assembly is properly level
before proceeding.
Pre-drill a pilot hole
before fastening screw
or lag to prevent
splitting of wood.
This indicates time to tighten bolts, but
not too tight! Do not crush the wood.
This may create splinters and cause
structural damage.
Part Identification Key
On each page, you will find the parts
and quantities required to complete the
assembly step illustrated on that page.
Here is a sample.
Key Number: The first two digits
represent the step number. The third
digit represents the piece. Note that if
the part is used in multiple steps then
the number only reflects the first step it
is used in.
Symbols
Throughout these instructions symbols are provided as important reminders for proper and safe assembly.
Proper Hardware Assembly
Lag screws require drilling pilot
holes to avoid splitting wood. Only
a flat washer is required. For ease of
installation liquid soap can be used
on all lag-type screws.
For bolts, tap T-Nut into hole with
hammer. Insert the hex bolt through
lock washer first then flat washer then
hole. Because the assemblies need to
be squared do not completely tighten
until instructed. Pay close attention to
diameter of the bolts. 5/16” is slightly
larger than 1/4”.
Note: Wafer head bolts with blue lock
tight or a bolt with a Ny-Lok nut do
NOT require a lock washer.
Once the assembly is tightened, watch for exposed threads.
If a thread protrudes from the T-Nut, remove
the bolt and add washers to eliminate this condition.
Extra washers have been provided for this purpose.
Use
Help
Use
Help
Measure
Distance
Square
Assembly
Use
Level
Pre-drill 1/8” & 3/16” Bit
Tighten
Bolts
CAUTION – Protrusion Hazard
Keys to Assembly Success
Tools Required
 Tape Measure
 Carpenters evel
 Carpenters Square
 Claw Hammer
 Standard or Cordless Drill
 1, 3 Phillips or Robertson
bit or Screwdriver
 Ratchet(1/2, /16 
9/16” sockets)
 Open End Wrench
(1/2, /16  /16)
 Adjustable Wrench
 1/  3/16 Drill Bits
 3/16 Hex Key
 ’ Step adder
 Safety Glasses
 Adult Helpers
 Pencil
Quantity Key Number Part Description,
Part Size
2X 012 Post 2 x 4 x 83”
No Yes
Lag Assembly
Bolt Assembly
Flat Washer
Lag Screw
Hex Bolt
Lock
Washer
Flat
Washer
Before mounting Lag
Screw, use factory drilled
holes as guides to drill 1/8”
pilot holes
T-Nut
(Hammer into place)
Do not crush wood!
If Bolt protrudes
beyond T-Nut
Use an extra
flat washer
6

Key Number: The rst two digits represent the step
number. The third digit represents the order in which
the part is listed in the step.
Note that if the part is used in multiple steps then
the key number only reects the rst step it is used in.
Part Quantity Key Number
Order Listed
(The order the part is
listed in step 1)
Part Description Part Size
2X 012 Post 2 x 4 x 83”
Your Key To Quick Assembly
SAVE TIME - TIP #1:
Open each box with wood parts and look for the Key Number
stamped on the end of the wood part (see chart below). Sort
each wood part into the different assembly steps.
SAVE TIME - TIP #2:
In addition to the key number stamp, you can also identify
the wood parts by using the Parts Identication pages in the
manual or the Parts Identication weather resistant poster.
HARDWARE:
The majority of each hardware part comes packed in a separate bag
so you do not need to sort the hardware. Each assembly step indicates
which hardware (bolt, screw, washer etc.) you will require to complete
the step.
SORTING WOOD PARTS INTO
EACH ASSEMBLY STEP WILL
SAVE TIME!
01 2
Step Number
(This is Step 1)
Step Step Step
7

311
312
TNR 3 Short Exit
9X TNR 2 Slide Elbow
TNR 2 Slide Lt Flange
TNR 2 Slide Rt Flange
6X MOD Tunnel Panel
Telescope w Mount
Double Ride Maze N Wave Slide
BBQ Utensils
Utensil Shelf X2
Cooktop
BBQ Lid
BBQ Base
Sink
Sign
TNR 4 Clamp Ring Set (10Pk)
Door Hardware
023
Narrow Front Panel
121
Door Window Panel
TNR 2 Slide Exit Top
531
532
Front Roof Panel
511
Front Small Roof
552
022
Slide End Panel
062
063 064
Fruit + Basket
031
Panel Front Wall
032
SW Wall Panel
021
Narrow Back Panel
Cedar Summit Plaque
TNR4 Post Mount
131
133
132
X2
MOD 5 Pane Window X4
MOD 3 Pane Gable X4
(hidden)
541
042
(hidden)
2X
641
2X
551
2X
502
Back Roof Panel
512
562
X2
563
X2
564
X2
561
X2
072
071
2X
621
611
X2
122
(hidden)
651
X2
652
X2
Narrow Angle Bracket X6
Steering Wheel
033
Back Rock Panel
Flat Panel Bracket X4 (hidden)
Corner Bracket X5
FRONT
Corner Panel Bracket X6 (hidden)
231
4X
204
2X
213
2X
205
201
121
203
193
2X
211
2X
202
2X
191
2X
192
2X
212
2X
222
8

153
2X
151 141
152
142
161
Heav L Bracket X3
Heav C Bracket
DX Swing Hanger (6Pk)
 Plaset Plaque
Swing Rope X4
Acro Rope X2
3X Steel
Hand Grip
05
02
01
03
040
07
06
09
090
091
091
090
Steel Hand Grip
Rebar Ground Stake X
2X Tunnel Bracket
12 Climbing Rope
Deluxe Pole X2
2X Deluxe Fling Flag
Plastic Formed
Washer (1Pk)
Bell w Horseshoe 2X
TNR3 Tube Mount
074
043
X2
052
053
13X
051
2X Flat Bracket
361
394
X2
2X
371
392
4X
391
X2
393
X2
353
351
352
343 342
2X
354
2X
51
351
X4
341
X6 (hidden)
571
4X
501
553
Back Small Roof
073
2X
572
061
BAC
Spring Loaded Quick Links x6
Acro Bar
Acro Handle X2
Swing Belt Seat X2
346
16X
345 344 396 395 411
X6
iew from nside
iew from nside
102
X2
105 104
103
101
Heav Flat Bracket x2
Rocks (1Pk)
041
(hidden)
9

(4) 231 - 1 x 4 x 29" - Cedar Wall - Box 2 - 3591975
(1) 053 - 1 x 4 x 35-5/8" - Narrow Floor Board - Box 2 - 3599050
(13) 051 - 1 x 5 x 35-5/8" - Floor Board - Box 2 - 3599051
(2) 202 - 1 x 2 x 34-1/8" - Upright Crowsnest - Box 2 - 3599072
(2) 213 - 3/4 x 3-1/4 x 14-3/4" - Crowsnest Side - Box 2 - 3599042
(2) 211 - 3/4 x 5-1/4 x 14-3/4" - Crowsnest Bottom Side - Box 2 - 3599037
(2) 565 - 15/16 x 3 x 19-1/4" - Wall Tie - Box 3 - 3599117
(2) 044 - Tie 1 x 3 x 24-1/2" - Box 2 - 3599123
(1) 105 - 5/8 x 2 x 21-49/64" - Top Front Rope - Box 2 - 3609171
(2) 102 - 5/8 x 1-1/4 x 33-7/8" - Side Rope Trim - Box 2 - 3609174
(1) 104 - 5/8 x 3-5/8 x 34" - Right Rope - Box 2 - 3609173
(1) 103 - 5/8 x 2-25/64 x 34" - Left Rope - Box 2 - 3609172
(1) 133 - 5/8 x 3-3/8 x 11-1/4" - Bell Top RT -
Box 2 - 3609101
(1) 131 - 5/8 x 3-3/8 x 11-1/4" - Bell Top -
Box 2 - 3609102
(1) 088 - 5/8 x 5-1/4 x 40-1/2" - Vert Rock Board D1 -
Box 4 - 3599181
(1) 087 - 5/8 x 5-1/4 x 40-1/2" - Vert Rock Board C1 -
Box 4 - 3599180
(1) 086 - 5/8 x 5-1/4 x 40-1/2" - Vert Rock Board B1 -
Box 4 - 3599179
(1) 085 - 5/8 x 5-1/4 x 40-1/2" - Vert Rock Board A1 -
Box 4 - 3599178
(3) 089 - 5/8 x 4-1/4 x 53" - Vert Rock Board Short A - Box 4 - 3599175
(1) 0891 - 5/8 x 4-1/4 x 53" - Vert Board Short - Box 4 - 3599177
(1) 0890 - 5/8 x 5 x 53" - Vert Rock Board Short Wide - Box 4 -
3599176
(1) 081 - 5/8 x 5-1/4 x 51-1/2" - Vert Rock Board A2 -
Box 4 - 3599196
(1) 082 - 5/8 x 5-1/4 x 51-1/2" - Vert Rock Board B2 -
Box 4 - 3599197
(1) 083 - 5/8 x 5-1/4 x 51-1/2" - Vert Rock Board C2 -
Box 4 - 3599198
(1) 084 - 5/8 x 5-1/4 x 51-1/2" - Vert Rock Board D2 -
Box 4 - 3599199
(1) 085 - 5/8 x 5-1/4 x 40-1/2" - Vert Rock Board A1R -
Box 4 - 3599275
(1) 086 - 5/8 x 5-1/4 x 40-1/2" - Vert Rock Board B1R -
Box 4 - 3599276
(1) 087 - 5/8 x 5-1/4 x 40-1/2" - Vert Rock Board C1R -
Box 4 - 3599277
(1) 088 - 5/8 x 5-1/4 x 40-1/2" - Vert Rock Board D1R -
Box 4 - 3599281
(1) 082 - 5/8 x 5-1/4 x 51-1/2" - Vert Rock Board B2R -
Box 4 - 3599278
(1) 083 - 5/8 x 5-1/4 x 51-1/2" - Vert Rock Board C2R -
Box 4 - 3599285
(1) 089 - 5/8 x 4-1/4 x 53" - Vert Rock Board Short R1 -
Box 4 - 3599279
(1) 091 - 5/8 x 4-1/4 x 53" - Vert Rock Board Short R3 -
Box 4 - 3599283
(1) 090 - 5/8 x 4-1/4 x 53" - Vert Rock Board Short R2 -
Box 4 - 3599282
(1) 0890 - 5/8 x 5 x 53" - Vert Rock Board Short Wide R -
Box 4 - 3599280
Part Identification (Reduced Size)
10

(1) 122 - 5/4 x 3 x 10" - Door Stop - Box 2 - 3592715
(1) 062 - 5/4 x 3 x 33" - alf Wall Top - Box 2 - 3599053
(1) 061 - 5/4 x 3 x 33-1/2" - SW Wall Top - Box 1 - 3599071
(1) 071 - 5/4 x 4 x 14 - SW round - Box 2 - 3592606
(1) 204 - 5/4 x 4 x 25-1/2" - Crowsnest Short - Box 3 - 3598115
(1) 064 - 5/4 x 5 x 39-5/8" - Tale Top - Box 3 - 3592611
(1) 193 - 5/4 x 4 x 34" - Crowsnest Back - Box 2 - 3599036
(1) 073 - 5/4 x 4 x 24-1/2" - Support Diagonal - Box 3 - 3599111
(2) 561 - 1-1/4 x 2-1/2 x 44-1/4" - TB Support - Box 3 - 3599114
(2) 562 - 1-1/4 x 3 x 16-1/2" - Right Upright - Box 2 - 3599110
(2) 564 - 1-1/4 x 3 x 16-1/2" - Centre Upright - Box 2 - 3599106
(2) 563 - 1-14  4-14  16-12 - Left Upright - Box 2 - 3599107
(1) 101 - 1-1/4 x 2 x 16-15/16" - Top Rope - Box 2 - 3609170
(1) 353 - 5/4 x 4 x 72-5/8" - Tunnel round - Box 4 - 3592926
(1) 221 - 1 x 6 x 29-3/8" - Crowsnest ap Board - Box 2 - 3599040
(2) 222 - 1 x 6 x 29-3/8" - Crowsnest Floor - Box 2 - 3599038
(16) 346 - 1 x 5 x 16-7/8" - Floor Board - Box 4 - 3599092
(1) 344 - 1 x 6 x 12-5/16" - Floor Board nd B - Box 2 - 3599183
(1) 345 - 1 x 5 x 16-7/8" - Floor Board nd A - Box 2 - 3599184
(2) 651 - 1 x 5 x 14-1/2" - Transom Board A - Box 2 - 3599115
(2) 652 - 1 x 5 x 10" - Transom Board B - Box 2 - 3599116
Part Identification (Reduced Size)
11

(1) 052 - 1-1/4 x 3 x 63-1/4" - Long Floor oist - Box 3 - 3599056
(1) 072 - 1-1/4 x 3 x 22" - Diagonal - Box 2 - 3592607
(1) 571 - 1-1/4 x 3 x 46-3/4" - Swing Top - Box 3 - 3599113
(1) 311 - 1-1/4 x 3 x 20-1/4" - TNR Upright - Box 3 - 3598965
(2) 572 - 1-1/4 x 2-1/2 x 16-1/2" - Swing Side Upright - Box 2 - 3599112
(2) 205 - 1-1/4 x 2 x 27-1/2" - Crowsnest Spacer - Box 2 - 3599043
(4) 501 - 1  2  33 - Roof Support - Box 2 - 3599105
(1) 312 - 1-1/4 x 3 x 32-1/4" - TNR round Brace - Box 3 - 3598963
(2) 621 - 1-1/4 x 3 x 6" - Roof nd Short - Box 2 - 3599103
(2) 611 - 1-1/4 x 4 x 6" - id Roof nd - Box 2 - 3599119
(2) 641 - 1-1/4 x 3 x 16-3/8" - Long Roof nd - Box 3 - 3599108
(1) 361 - 1-1/4 x 4-1/2 x 21" - Tunnel Support - Box 4 - 3599185
(2) 393 - 1-1/4 x 5 x 19-5/8" - Tunnel Arch - Box 4 - 3592924
(2) 391 - 1-1/4 x 4 x 19-5/8" - Tunnel Top - Box 4 - 3592932
(4) 392 - 1-3/8 x 3-3/8 x 33" - Tunnel Post - Box 4 - 3592931
(2) 551 - 1-1/4 x 2-1/4 x 32-3/4" - id Roof Support - Box 2 - 3599109
(2) 502 - 1-1/4 x 2-1/4 x 29-11/16" - Roof Support Small - Box 2 - 3599104
(1) 042 - 1-1/4 x 3 x 40-3/4" - Floor oist - Box 2 - 3592608
(4) 351 - 1-1/8" x 18-5/8" - Dowel - Tennon - Box 4 - 3681858
(6) 341 - 1-1/8 x 15-7/8" - Dowel - Tennon - Box 4 - 3681578
(1) 541 - 1-1/4 x 3 x 10" - Dormer Cleat - Box 2 - 3599122
(1) 395 - 1-3/8 x 4-1/2 x 7 25/32" - Short Tunnel Rail - Box 4 - 3599186
(1) 041 - 1-1/4 x 3 x 29-3/4" - Floor oist - Box 3 - 3599182
Part Identification (Reduced Size)
12

(1) 152 - 2-1/2 x 3 x 15" - Block SW FSC - Box 2 - 3598507
(1) 151 - 2-1/2 x 3 x 15" - SW Block Angle - Box 2 - 3599068
(1) 142 - 4 x 4 x 16" - SW ount - Box 3 - 3599069
(1) 161 - 2-1/2 x 3 x 51" - Support Cross - Box 1 - 3599067
(2) 153 - 4 x 4 x 92" - SW Post - Box 1 - 3599070
(1) 141 - 4 x 6 x 92" - ngineered SW Beam - Box 1 - 3599049
(2) 191 - 2 x 6 x 15" Crowsnest usset - Box 2 - 3598112
(1) 074 - 2 x 3 x 42" - Diagonal - Box 1 - 3598587
(2) 581 - 1-1/2 x 1-1/2 x 55-1/2" - Wall Support - Box 1 - 3599118
(2) 043 - 2 x 2 x 63" - Side oist - Box 1 - 3599064
(1) 203 - 2 x 4 x 29-1/2" - Crowsnest Front - Box 2 - 3599039
(1) 201 - 2 x 4 x 29-1/2" - Crowsnest Top - Box 2 - 3599044
(2) 192 - 2 x 4 x 13-1/2" - Crowsnest oist - Box 3 - 3599041
(2) 212 - 2 x 4 x 12-1/2" - Short Crowsnest oist - Box 2 - 3599063
(2) 132 - 1-1/2 x 1-1/2 x 10-5/8" - Bell Support - Box 2 - 3609100
(1) 396 - 1-3/8 x 4-1/2 x 16-47/64" - Tunnel Rail - Box 4 - 3599187
(6) 411 - 1-1/2 x 1-1/2 x 33" - Picket - Box 1 - 3592920
(2) 371 - 1-3/8 x 3-3/8 x 33" - Access Upright - Box 4 - 3592917
(2) 394 - 1-3/8 x 4-1/2 x 18-3/4" - Safet Rail - Box 4 - 3592922
(1) 351 - 1-3/8 x 3-3/8 x 91-11/16" - Tunnel Ladder Rail Right - Box 4 - 3592927
(1) 352 - 1-3/8 x 3-3/8 x 91-11/16" - Tunnel Ladder Rail Left - Box 4 - 3592928
(1) 342 - 1-3/8 x 4-1/2 x 81-9/32" - Tunnel  Rail Right - Box 4 - 3599188
(1) 343 - 1-3/8 x 4-1/2 x 90-15/64" - Tunnel  Rail Left - Box 4 - 3599189
(2) 354 - 1-3/8 x 2-1/2 x 53" - Tunnel Diagonal - Box 4 - 3592925
(1) 063 - 2 x 2 x 39-5/8" - Tale Support - Box 1 - 3592612
Part Identification (Reduced Size)
13

(1) 023 - 1-1/4 x 21-1/2 x 92" - 37599003
Narrow Front Panel - Box 2
(1) 032 - 1-1/4 x 37 x 92"
SW Wall Panel
Box 3 - 37599007
(1) 121 - 1-1/4 x 15-3/4 x 42-1/8"
Door Window Panel
Box 2 37608977
(1) 031 - 1-1/4 x 43 x 92"
Panel Front Wall
Box 2 - 37599135
(1) 022 - 1-1/4 x 37 x 92"
Slide nd Panel
Box 3 - 37598981
(1) 033 - 1-1/4 x 43 x 92"
Back Rock Panel
Box 2 - 37599165
(1) 021 - 1-1/4 x 21-1/2 x 92"
Narrow Back Panel - Box 2 - 37599192
Part Identification (Reduced Size)
14

1x -  2   
3310222 
1x -  2   
3310223 
9x -  2  
3310221 
1x -  4   
3300230  10 
1x -  2   
3310224 
1x - 3  
3310232 
(1) 511 Front Roof Panel 1 x 37 x 45" - Box 3 -
37599082
(1) 512 Back Roof Panel 1-1/4 x 32 x 45" - Box 3 -
37599124
(1) 553 Back Small Roof 1-1/4 x 28-15/16 x 21-7/8" -
Box 3 - 37599091
(1) 552 Front Small Roof 1 x 29 3/16 x 21-7/8" -
Box 3 - 37599098
1x -   
6  
3330100
1x - 532 531 Dormer Roof Set
(Left/Right Dormer) - Box 3 -
3598068
Part Identification (Reduced Size)
15

(96) S3 -  
8  2-12
- 52043522
(59) S4 -  
8  3
- 52043530
(40) S7 -  
12  2
- 52433620
(43) S6 -  
12  1
- 52433610
(64) S10 -  
8  1
- 52433510
18pc S5 -  
8  12
- 9264504
(304) S20 -  
8  1-38
- 52043516
(96) S0 -  
8  78
- 52933505
(3) LW2 - 516   - 51303300
(18) LN2 - 516  
-
54303300
(23) TN2 - 516 - 
-
54503300
(34) BN1 - 14  
-
54803200
(47) TN1 - 14  - 
-
54503200
(81) LW1 - 14   - 51303200
(77) FW2 - 516   - 51103300
(65) FW1 - 14   - 51103200
1pc - PB5 - 
14  2
- 9274220
2pc PB7 - 
12  12
- 
(40) S8 -  
12  34
- 52433603
(12) PB6 -  
14  1
- 53413210
(132) LN1 -
14  
- 54303200
(16) FW6 - 12   - 9299500
(35) PB2 -  
14  1-14
- 53433212
18pc FW6 -    -
9290000
(12) FW10 - 38   - 51103800
(12) TS -  
6  30
- 52953911
(6) LN3 -
38  
- 54303800
(120) PB1 -  
14  34
- 53453203
(30) S37 -  
7  58
- 52433009
(8) S38 -  
7  1-18
- 52433014
(105) S11 -  
8  2
- 52043520
(16) S1 -  
8  1-18
- 52043514
30pc PB7 -  
14  12
- 53453202
30pc LN5 -
14   
- 54903200
(15) FW3 - 8   -
9251500
(22) FW0 - 316   - 51103100
(17) B1 -  
12  12
- 53433602
(17) LN4 -
12  
- 54303600
ardware Identification  
16

1 8 -
Hex Bolt 1/4 x 4-1/4"
- (53703241)
4 5 -
Hex Bolt 1/4 x 4-1/2"
- (53703242)
2 5 
Hex Bolt 5/16 x 4-1/2"
- (53703342)
4 3 -
Hex Bolt 1/4 x 2-1/2"
- (53703222)
6 9 -
Hex Bolt 1/4 x 1-1/4"
- (53703211)
22 11 -
Hex Bolt 1/4 x 2-3/4"
- (53703223)
4
13 -
Hex Bolt 1/4 x 3-1/2" - (53703232)
4 10 -
Hex Bolt 1/4 x 2-1/4"
- (53703221)
2
12 -
Hex Bolt 1/4 x 3"
-
(53703230)
18 5 - Wafer Lag
1/4 x 2-1/2"
- (52613222)
6 3 - Wafer Lag
1/4 x 1-3/8"
- (52613216)
5 S9 - Lag Screw
5/16 x 4-3/4"
- (52213343)
6 9 -
Wafe
r
Bolt 5/16 x 2-1/8"
- (53613324)
1 8 -
Wafer Bolt 5/16 x 2-3/8"
- (53613326)
  -
Wafer Bolt 5/16 x 3"
- (53613330)
4 21 -
Hex Bolt 5/16 x 3-3/4"
- (53703333)
12 13 -
Hex Bolt 5/16 x 6-1/8"
- (53703364)
 10 -
Wafer Bolt 5/16 x 2-5/8"
- (53613329)
1 26 -
Hex Bolt 3/8 x 9-1/4"
- (53703891)
4 1 -
Hex Bolt 3/8 x 6"
- (53703860)
1 20 -
Hex Bolt 3/8 x 4"
- (53703840)
2 22 
Hex Bolt 5/16 x 5"
- (53703350)
ardare dentification (Actual Size)
17

1x - Crimp Rope Bag (3502045)
2x Acro Rope EN71
4x Swing Rope w/ Crimps
2x - Acro Handle
(9320131) Green
1x - Quick Links w.
Thread (2pk)
(3200022)
1x - Telescope w/ Mount
(3320161)
1x - Quadrex Driver
(9200015)
3x - Steel Hand Grip
(9200211) -Yellow
1x - Cedar Summit
Plaque
(9320358)
2x - Swing Belt Seat
(9320130) Green
1x - Steering Wheel
(3320255)
1x - Plastic Formed
Washer (18 Pk)
(3290000)
2x - Flat Panel Bracket
(2 Pk)(3205978)
1x - Canyon Ridge Bracket Set
(3205715)
1x - Acro Bar
(9200131) Green
1x - Rebar Ground Stake
(6 Pk) (3200318)
2x - Rebar Ground Stake
(9290318)
1x - DX Swing Hangers
with Quick Links (6 Pk)
(3201950)
1x - Corner
Bracket (5 Pk)
(3205979)
3x - Narrow Angle
Bracket (2 Pk)
(3205939)
1x - #2 x 2"
Robertson Driver
(9200014)
1x - 12' Climbing Rope 5/8"
(3502150)
3x - Heavy L-Bracket
(9200151)
1x - Heavy Bracket Set
(3205701) Green
2x 9201712
Door Hinge -Green
9207713
Door Catch -Brown
2x 9201711
Door Handle -Green
1x Magnetic Catch
1x Catch Plate
1x - Door Hardware (3201710)
1x - TNR3 Tube Support
(9200258)
1x - Heavy C-Bracket
(9200153)
2x - Heavy Flat Bracket
(9200149)
1x - Corner Panel
Bracket (6 Pk)
(3205977)
1x - BBQ Deluxe Kitchen
Set (3330007)
1x - BBQ Base
33308011
1x
- BBQ Cooktop 3330909
1x - BBQ Lid
9330718
1x
- Basket with
Fruit 3330013
2x - Utensil Shelf
9320125
1x
- Sign
9330714
1x - Deluxe Flying Flag
(3330316) (2 Pk)
1x - Deluxe Pole
(3330328) (2 Pk)
2x - Bell with Horseshoe
(3200307)
1x - MOD 3 Pane Gable
(3330104) (4 Pk)
1x - Flat Bracket (2 Pk)
(3205960)
1x - BBQ Sink Set
3330908
2x - MOD 5 Pane Window
(2 Pk) (3330102)
1x - Maze N Wave Double Slide
(3318220) Yellow
1x
- Steel Hand Grip (9200222) -Yellow
1x - Tunnel Bracket (2 Pk)
(3200176)
1x - TNR4 Post Mount
Clamp
(9203657)
1x - TNR4 Post Mount
Base
(9203656)
30x - 1/4 x 12.7mm Pan
Head Bolt
(53453202)
31x - Square Nylok Nut
(54902200)
1x - 1/4 x 14.5mm Pan
Head Bolt
(53452209)
1x - 3/8" Drill Bit
1x - Kidkraft ID Paque
(9320370)
1x - BBQ Utensils
3330810
1x - TNR4 Post Mount Set (9203655)
1x - Rock Set(18pk)
(3325730)
Part Identification (Reduced Part Size)
18

B. If there are any missing or damaged pieces or you need assistance with
assembly please contact the consumer relations department directly. Call us
before going back to the store.
STOP STOPSTOP STOP
Key Number: The rst two digits represent the step
number. The third digit represents the piece. Note
that if the part is used in multiple steps then the
number only reects the rst step it is used in.
Quantity Key Number Part Description,
Part Size
2X 012 Post 2 x 4 x 83”
Step 1: Inventory Parts - Read This Before Starting Assembly
C. Read the assembly manual completely, paying special attention to EN71 and
ASTM warnings; notes; and safety/maintenance information on pages 1 - 6.
D. Before you discard your cartons ll out the form below.
• The carton I.D. stamp is located on the end of each carton. The tracking number is
located on the Cedar Summit ID Plaque (9320370).
• Please retain this information for future reference. You will need this information if you
contact the Consumer Relations Department.
• Please refer to Page 6 for proper hardware assembly.
• Each step indicates which bolts and/or screws you will need for assembly, as well as
any at washers, lock washers, t-nuts or lock nuts.
A. This is the time for you to inventory all your hardware, wood and accessories,
referencing the parts identication sheets. This will assist you with your assembly.
• The wood pieces will have the key number stamped on the ends of the boards.
Organize the wood pieces by step, as per the key numbering system below.
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 4)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 5)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 6)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 1)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 2)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 3)
MODEL NUMBER: F25730EX
TRACKING NUMBER (from ID Plaque):
[email protected]
Online Parts Replacement:
Cedarsummitplay.com/parts-center-warranty-claim
Customer Service:
1(800) 933-0771 or [phone]
Europe Customer Service: [phone]
[email protected]
EU Online Parts Replacement: parts.kidkraft.eu
19

1 x Slide End Panel 1-1/4 x 37 x 92”
1 x Narrow Back Panel 1-1/4 x 21-1/2 x 92”
1 x Narrow Front Panel 1-1/4 x 21-1/2 x 92”
Wood Parts
022
Step 2: Slide Wall Assembly
A: Place (021) Narrow Back Panel against the left side of (022) Slide End Panel noticing panel orientation. The
tops and bottoms of the panels should be ush and panels square. Pre-drill with a 3/16” drill bit, then fasten
(021) Narrow Back Panel to (022) Slide End Panel with 4 (WL5) 1/4 x 2-1/2” Wafer Lags. (g. 2.1 & 2.2)
B: Place (023) Narrow Front Panel against the right side of (022) Slide End Panel noticing panel orientation.
The tops and bottoms of the panels should be ush and panels square. Pre-drill with a 3/16” drill bit, then fasten
(022) Slide End Panel to (023) Narrow Front Panel with 4 (WL5) 1/4 x 2-1/2” Wafer Lags. (g. 2.1 & 2.3)
Fig. 2.2
Fig. 2.1
Hardware
8 x 1/4 x 2-1/2” Wafer Lag
WL5
021
023
Fig. 2.3
Notice (021) Narrow
Back Panel overlaps
(022) Slide End Panel
Flush
Flush
022
022
021
023
WL5
023
022
Notice (022) Slide End
Panel overlaps (023)
Narrow Front Panel
Flush
021
20