KidKraft F24145 User manual

INSTALLATION AND OPERATING INSTRUCTIONS
To reduce the risk of serious injury or death, you must read and
follow these instructions. Keep and refer to these instructions often
and give them to any future owner of this play system. Manufacturer contact information provided below.
OBSTACLE FREE SAFETY ZONE - 22’3” x 28’ area requires Protective Surfacing. See page 3.
MAXIMUM VERTICAL FALL HEIGHT - 6’ (1.8 m)
CAPACITY - 6 Users Maximum, Ages 3to 10; Weight Limit 110 lbs. (49.9 kg) per child.
RESIDENTIAL HOME USE ONLY. Not intended for public areas such as schools, churches, nurseries, day cares or parks.
WARNING
9404145 Rev 07/03/2020
Table of Contents
Warnings and Safe Play Instructions. . . . . . . . . . . . . . . pg. 2
Protective Surfacing Guidelines. . . . . . . . . . . . . . . . . . . pg. 3
Instructions for Proper Maintenance .......... . . . . . pg. 4
About Our Wood – Limited Warranty ......... . . . . . pg. 5
Keys to Assembly Success ................. . . . . . pg. 6
Part ID.................................. . . . . . pg. 7
Installation of I.D./Warning Plaque ....... . . . . .Final Step
4 - 8 Hrs
Two person
assembly
KidKraft Netherlands BV
Olympisch Stadion 8
1076 DE Amsterdam
The Netherlands
[email protected]
[phone] M-F from 09:00 to 17:30
(GMT+1)
For online parts replacement visit
https://parts.kidkraft.eu/
KidKraft, Inc.
4630 Olin Road
Dallas, Texas 75244 USA
[email protected]
[email protected]
1.800.933.0771
972.385.0100
For online parts replacement visit
https://parts.kidkraft.com/
A INSLEY
PLAY
SYSTEM
F24145
Warning. Only for domestic use.

2
Warnings and Safe Play Instructions
CONTINUOUS ADULT SUPERVISION REQUIRED. Most serious injuries and deaths on playground equipment have occurred
while children were unsupervised! Our products are designed to meet mandatory and voluntary safety standards. Complying
with all warnings and recommendations in these instructions will reduce the risk of serious or fatal injury to children using
this play system. Go over the warnings and safe play instructions regularly with your children and make certain that they
understand and follow them. Remember on-site adult supervision is required for children of all ages.
SERIOUS HEAD INJURY HAZARD
Installation over concrete, asphalt, dirt, grass, carpet
and other hard surface creates a risk of serious injury
or death from falls to the ground. Install and maintain
shock absorbing material under and around play-set as
recommended on page 3 of these instructions.
COLLISION HAZARD
Place play-set on level ground at least 2m from any
obstruction such as a garage or house, fences, poles,
trees, sidewalks, walls, landscape timbers, rocks,
pavement, planters, garden borders, overhanging
branches, laundry lines, and electrical wires. (See
OBSTACLE FREE SAFETY ZONE on cover)
CHOKING HAZARD/SHARP EDGES & POINTS
Adult assembly required. This product contains small
parts and parts with sharp edges and points. Keep parts
away from children until fully assembled.
WARNING LABEL
Owners shall be responsible for maintaining the legibility
of the warning labels.
STRANGULATION HAZARD
,senilsehtolc,seporhtiwyalpotnerdlihcwollaREVEN•
pet leashes, cables, chains or cord-like items when using
this play-set or to attach these items to play-set.
ponchos, hoods, scarves, capes, necklaces, items with
draw-strings, cords or ties when using this play-set.
stemlehtropsroekibraewotnerdlihcwollaREVEN•
when using this play-set.
Failure to prohibit these items, even helmets with chin
straps, increases the risk of serious injury and death to
children from entanglement and strangulation.
TIP OVER HAZARD
Choose a level location for the equipment. This can reduce
the likelihood of the play set tipping over and loose-fill
surfacing materials washing away during heavy rains.
D
Never add extra length to chain or rope. The chains or ropes
provided are the maximum length designed for the swinging
element(s).
O NOT allow children to play on the play-set until the
assembly is complete and the unit is properly anchored.
WARNING
eeS.tes-yalpruoyfosnoitatimilyticapacevresbO
front cover.
gnisolcnetoofllufdnagnittfillewhtiwnerdlihcsserD
footwear.
retnecehtnithgiewllufriehthtiwtisotnerdlihchcaeT
of the swing seat to prevent erratic swing motion or
falling off.
,gnissim;doowdekcarcronekorb,deretnilpsrofkcehC
loose, or sharp edged hardware. Replace, tighten and or
sand smooth as required prior to playing.
niahc,sreddalepor,seporgnibmilcdednepsustahtyfireV
or cable are secured at both ends and cannot be looped
back on itself as to create an entanglement hazard.
rehtodnaedilsehtkcehc,syadtohrodnaynnusnO
plastic rides to assure that they are not very hot as to
cause burns. Cool hot slide and rides with water and wipe
dry prior to using.
raewtoofleehroeotneporaewotnerdlihcwollatonoD
like sandals, flip–flops or clogs.
dniheb,neewteb,tnorfni,klawotnerdlihcwollatonoD
or close to moving rides.
poolroseporrosniahcgniwstsiwtnerdlihcteltonoD
them over the top support bar. This may reduce the
strength of the chain or rope and cause premature failure.
.noitomnierayehtelihwsedirffotegnerdlihcteltonoD
.tewsitinehwtnempiuqenognibmilctimreptonoD
anitnempiuqefoesuroyalphguortimreptonoD
manner for which it was not intended. Standing on or
jumping from the roof, elevated platforms, swings,
climbers, ladders or slide can be dangerous.
.staesrosedirytpmegniwsotnerdlihcwollatonoD
rotsrfidaehedilsnwodogotnerdlihcwollatonoD
run up slide.
WARNING – Safe Play Instructions
Orientate slide such that it gets the least amount of exposure
to the sun.

One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing
protective surfacing under and around your play equipment. The protective surfacing should be applied to a depth that is suitable
for the equipment height in accordance with ASTM F1292. There are different types of surfacing to choose from; whichever
product you select, follow these guidelines:
Loose-Fill Materials
• Maintain a minimum depth of 9 inches of loose-fill materials such as wood mulch/chips, engineered wood fiber (EWF), or
shredded/recycled rubber mulch for equipment up to 8 feet high; and 9 inches of sand or pea gravel for equipment up to 5 feet
high. NOTE: An initial fill level of 12 inches will compress to about a 9-inch depth of surfacing over time. The surfacing will also
compact, displace, and settle, and should be periodically raked and refilled to maintain at least a 9-inch depth.
• Use a minimum of 6 inches of protective surfacing for play equipment less than 4 feet in height. If maintained properly, this
should be adequate. (At depths less than 6 inches, the protective material is too easily displaced or compacted.)
NOTE: Do not install home playground equipment over concrete, asphalt, or any other hard surface. A fall onto a hard surface
can result in serious injury to the equipment user. Grass and dirt are not considered protective surfacing because wear and
environmental factors can reduce their shock absorbing effectiveness. Carpeting and thin mats are not adequate protective
surfacing. Ground level equipment -- such as a sandbox, activity wall, playhouse or other equipment that has no elevated play
surface -- does not need any protective surfacing.
• Use containment, such as digging out around the perimeter and/or lining the perimeter with landscape edging. Don’t forget to
account for water drainage.
• Periodically rake, check and maintain the depth of the loose-fill surfacing material. Marking the correct depth on the play
equipment support posts will help you to see when the material has settled and needs to be raked and or replenished. Be sure to
rake and evenly redistribute the surfacing in heavily used areas.
• Do not install loose fill surfacing over hard surfaces such as concrete or asphalt.
Poured-In-Place Surfaces or Pre-Manufactured Rubber Tiles
You may be interested in using surfacing other than loose-fill materials - like rubber tiles or poured-in-place surfaces.
• Installations of these surfaces generally require a professional and are not “do-it yourself” projects.
• Review surface specifications before purchasing this type of surfacing. Ask the installer/manufacturer for a report showing that
the product has been tested to the following safety standard: ASTM F1292 Standard Specification for Impact Attenuation of
Surfacing Materials within the Use Zone of Playground Equipment. This report should show the specific height for which the
surface is intended to protect against serious head injury. This height should be equal to or greater than the fall height - vertical
distance between a designated play surface (elevated surface for standing, sitting, or climbing) and the protective surfacing
below - of your play equipment.
• Check the protective surfacing frequently for wear.
Placement
Proper placement and maintenance of protective surfacing is essential. Refer to diagram on front cover. Be sure to;
• Extend surfacing at least 6 feet from the equipment in all directions.
• For to-fro swings, extend protective surfacing in front of and behind the swing to a distance equal to twice the height of the top
bar from which the swing is suspended.
• For tire swings, extend surfacing in a circle whose radius is equal to the height of the suspending chain or rope, plus 6 feet in all directions.
From the CPSC Outdoor Home Playground Safety Handbook. At www.cpsc.gov/CPSCPUB/PUBS/324.pdf
Protective Surfacing - Reducing Risk of Serious Head Injury From Falls.
3
2H 2H
H
Denotes Use Zone with Protective Surfacing
Use Zone for Single-Axis Swings
6 ft.
6 ft.
6 ft.
6 ft.
Denotes Use Zone with Protective Surfacing
Use Zone for Multi-Axis Swings
6 ft. 6 ft.
6 ft.
L
33

Instructions for Proper Maintenance
HARDWARE:
Check metal parts for rust. If found,
sand and repaint using a non-lead
paint complying with 16 CFR 1303.
Inspect and tighten all hardware. On
wood assemblies DO NOT OVER-
TIGHTEN as to cause crushing and
splintering of wood.
Check for sharp edges or protruding screw threads, add
washers if required.
SHOCK ABSORBING SURFACING:
Check for foreign objects. Rake and check depth of loose
fill protective surfacing materials to prevent compaction
and maintain appropriate depth. Replace as necessary.
(See Protective Surfacing, page 3)
GROUND STAKES (ANCHORS):
Check for looseness, damage or deterioration. Should
firmly anchor unit to ground during use. Re-secure and
or replace, if necessary.
SWING HANGERS:
Check that bolts are secure and tight. Quick clips should
be completely closed and threaded clips screwed tight.
If squeaking occurs lubricate bushings with oil or WD-40®.
SWINGS, ROPES AND RIDES:
Reinstall if removed during cold season. Check all
moving parts including swing seats, ropes, chains and
attachments for wear, rust and other deterioration.
Replace as needed.
Check that ropes are tight, secure at both ends and
cannot loop back as to create an entrapment.
WOOD PARTS:
Check all wood members for deterioration, structural
damage and splintering. Sand down splinters and replace
deteriorated wood members. As with all wood, some
checking and small cracks in grain is normal.
Unprotected, they will appear weathered over time.
Periodic application of an exterior water repellent or stain
(water-based) will help improve appearance and life.
Your KidKraft Play System is designed and constructed of quality materials with your child’s safety in mind. As with all outdoor
products used by children, it will weather and wear. To maximize the enjoyment, safety and life of your Play Set, it is important
that you, the owner, properly maintain it.
Check the following at the beginning of the play season:
HARDWARE:
Inspect for tightness. Must be firmly against, but not
crushing the wood. DO NOT OVER-TIGHTEN.
This will cause splintering of wood.
Check for sharp edges or protruding screw threads.
Add washers if required.
SHOCK ABSORBING SURFACING:
Rake and check depth of loose fill protective surfacing
materials to prevent compaction and maintain appropriate
depth. Replace as necessary.
(See Protective Surfacing, page 3)
Check twice a month during play season:
SWING HANGERS:
Check that they are secure and orientated correctly. Hook
should rotate freely and perpendicular to support beam.
If squeaking occurs lubricate bushings with oil or WD-40®.
SWINGS AND RIDES:
Check swing seats, all ropes, chains and attachments for
fraying, wear, excessive corrosion or damage.
Replace if structurally damaged or deteriorated.
Check once a month during play season:
SWINGS AND RIDES:
To prolong their life, remove swings and store inside
when outside temperature is below 32°F/0°C. Below
freezing, plastic parts may become more brittle.
SHOCK ABSORBING SURFACING:
Rake and check depth of loose fill protective surfacing
materials to prevent compaction and maintain appropriate
depth. Replace as necessary.
(See Protective Surfacing, page 3)
Check at the end of the play season:
If you dispose of your play set: Please disassemble and dispose of your unit so that it does not create any unreasonable hazards
at the time it is discarded. Be sure to follow your local waste ordinances.
4
Use an extra
Flat Washer
If Bolt protrudes
beyond T-Nut
44

5
About Our Wood
KidKraft Premium Play Systems uses only premium playset lumber, ensuring the safest product for your children’s use. Although we
take great care in selecting the best quality lumber available, wood is still a product of nature and susceptible
to weathering which can change the appearance of your set.
What causes weathering? Does it affect the strength of my Play System?
One of the main reasons for weathering is the effects of water (moisture); the moisture content of the wood at the surface is
different than the interior of the wood. As the climate changes, moisture moves in or out of the wood, causing tension which can
result in checking and or warping. You can expect the following due to weathering. These changes will not affect the strength of
the product:
1. Checking is surface cracks in the wood along the grain. A post (4” x 4”)will experience more checking than a board (1” x 4”)
because the surface and interiormoisture content will vary more widely than in thinner wood.
2. Warping results from any distortion (twisting, cupping) from the original plane ofthe board and often happens from rapid
wettingand drying of the wood.
3. Fading happens as a natural change in the wood coloras it is exposed tosun-light and will turn a grey over time.
How can I reduce the amount of weathering to my Play System?
At the factory we have coated the wood with a water repellent or stain. This coating decreases the amount of water absorption
during rain or snow thus decreasing the tension in the wood. Sunlight will break down the coating, so we recommend applying a
water repellent or stain on a yearly basis (see your local stain and paint supplier for a recommended product).
Most weathering is just the normal result of nature and will not affect safe play and enjoyment for your child. However if you are
concerned that a part has experienced a severe weathering problem please call our consumer relations department for further assistance.
Complete and mail registration card to receive important product notifications and assure prompt
warranty service.
5 Year Limited Warranty
KidKraft warrants that this product is free from defect in materials and workmanship for a period of one
year from the original date of purchase. In addition, lumber is warranted for 5 years against structural
failure due to rot and insect damage. All other parts, such as hardware, swings, rides, accessories, and
slides carry a one-year warranty only.
This warranty applies to the original owner and registrant and is non-transferable.
Regular maintenance is required to assure the integrity of your Play System. This warranty does not
cover any inspection cost.
This Limited Warranty does not cover:
•Labor for replacement of any defective item(s);
•Incidental orconsequential damages;
•Cosmetic defects whichdo not affect performance or integrity;
•Vandalism; improper use or installation; acts of nature;
•Minortwisting, warping, checking,or any other natural occurring properties of wood that do not
affect performance or integrity.
KidKraft products have been designed for safety and quality. Any modifications made to the original
product could damage the structural integrity of the unit leading to failure and possible injury.
Kidkraft cannot assume any responsibility for modified products. Furthermore, modification voids
any and all warranties.
This product is warranted for RESIDENTIAL USE ONLY. Under no circumstance should a
KidKraft Play System be used in public settings such as schools, churches, playgrounds, parks, day
cares and the like. Such use may lead to product failure and potential injury. Any and all public use
will void this warranty.
KidKraft disclaims all other representations and warranties of any kind, express or implied.
This Warranty gives you specific legal rights. You may have otherrights as well which vary from state to state or
province to province. This warranty excludes all consequential damages, however, some states do notallow the
limitation or exclusion ofconsequential damages, andtherefore this limitation may not apply to you.

6
This identifies information that requires special
attention. Improper assembly could lead to an unsafe
or dangerous condition.
Where this is shown, 2 or 3 people
are required to safely complete the
step. To avoid injury or damage
to the assembly make sure to get
help!
Check that assembly is square
before tightening bolts.
Use a measuring tape to assure
proper location.
Check that set or assembly is properly level
before proceeding.
Pre-drill a pilot hole
before fastening screw
or lag to prevent
splitting of wood.
This indicates time to tighten bolts, but
not too tight! Do not crush the wood.
This may create splinters and cause
structural damage.
Part Identification Key
On each page, you will find the parts
and quantities required to complete the
assembly step illustrated on that page.
Here is a sample.
Key Number: The first two digits
represent the step number. The third
digit represents the piece. Note that if
the part is used in multiple steps then
the number only reflects the first step it
is used in.
Symbols
Throughout these instructions symbols are provided as important reminders for proper and safe assembly.
Proper Hardware Assembly
Lag screws require drilling pilot
holes to avoid splitting wood. Only
a flat washer is required. For ease of
installation liquid soap can be used
on all lag-type screws.
For bolts, tap T-Nut into hole with
hammer. Insert the hex bolt through
lock washer first then flat washer then
hole. Because the assemblies need to
be squared do not completely tighten
until instructed. Pay close attention to
diameter of the bolts. 5/16” is slightly
larger than 1/4”.
Note: Wafer head bolts with blue lock
tight or a bolt with a Ny-Lok nut do
NOT require a lock washer.
Once the assembly is tightened, watch for exposed threads.
If a thread protrudes from the T-Nut, remove
the bolt and add washers to eliminate this condition.
Extra washers have been provided for this purpose.
Use
Help
Use
Help
Measure
Distance
Square
Assembly
Use
Level
Pre-drill 1/8” & 3/16” Bit
Tighten
Bolts
CAUTION – Protrusion Hazard
Keys to Assembly Success
Tools Required
• Tape Measure
• Carpenters Level
• Carpenters Square
• Claw Hammer
• Standard or Cordless Drill
• #1, #3 Phillips or Robertson
bit or Screwdriver
• Ratchet(1/2”, 7/16” &
9/16” sockets)
• Open End Wrench
(1/2”, 7/16” & 9/16”)
• Adjustable Wrench
• 1/8” & 3/16” Drill Bits
• 3/16” Hex Key
• 8’ Step Ladder
• Safety Glasses
• Adult Helpers
• Pencil
Quantity Key Number Part Description,
Part Size
2X 012 Post 2 x 4 x 83”
No Yes
Lag Assembly
Bolt Assembly
Flat Washer
Lag Screw
Hex Bolt
Lock
Washer
Flat
Washer
Before mounting Lag
Screw, use factory drilled
holes as guides to drill 1/8”
pilot holes
T-Nut
(Hammer into place)
Do not crush wood!
If Bolt protrudes
beyond T-Nut
Use an extra
flat washer

7
Part Quantity Key Number Part Description Part Size
2X 0124 Post 2 x 4 x 83”
Your KeyTo Quick Assembly
SAVE TIME- TIP #1:
Open each box withwood parts and look for the Key Number
stamped on the end of the wood part (see chart below). Sort
each wood part into the different assembly steps.
SAVE TIME- TIP #2:
In addition tothe key number stamp, you can alsoidentify
the wood parts by
HARDWARE:
The majority of each hardware part comes packed inaseparate
bag so you do not need tosort the hardware. Each assembly step
indicates which hardware (bolt, screw, washer etc.) you will require
to complete the step.
SORTING WOOD PARTS INTO
EACH ASSEMBLY STEP WILL
SAVE TIME!
Step Step Step

3640369 Box 1
0369
(1) Lower Diagonal 2 x 3 x 37"
3640359 Box 1
0359
(2) Front Divider 1 x 4 x 38"
3641749 Box 1
1749
(2) SW Post 2 x 4 x 79-1/2"
3631772 Box 1
1772
(1) CE SW Beam Back 2 x 6 x 69-1/2"
"
1" x 4"
(Reduced Size)Part Identification
1" x 5"
1" x 6"
5/4" x 6"
5/4" x 5"
5/4" x 4"
2" x 2"
2" x 3"
2" x 4"
2" x 6"
1" x 2"
Actual Size
1½" x 5⅜"
1⅜" x 3⅜"
1⅜" x 2½"
1½" x 1½"
1" x 3½"
1" x 4½"
1" x 5½"
⅝" x 5⅜"
⅝" x 4½"
⅝" x 3⅜"
⅝" x 1⅜
Nominal Size
3631773 Box 1
1773
(1) CE SW Beam Front 2 x 6 x 69-1/2"
WOOD CHART
3630304 Box 1
(5) CE Floor Board 1 x 4 x 32-1/2"
0304
3631774 Box 1
1774
(2) CE Gap Board 1 x 6 x 23-1/2"
3631776 Box 1
1776
(5) Floor Board 1 x 6 x 23-1/2"
3631777 Box 1
1777
(2) CE Rock Board B 1 x 6 x 17"
3631778 Box 1
1778
(2) CE Rock Board A 1 x 6 x 17"
3631779 Box 1
1779
(1) CE Access Board 1 x 6 x 17"
3640312 Box 1
0312
(1) Gusset 2 x 3 x 16"
3641748 Box 1
1748
(1) SW Top 1 x 4 x 26-7/8"
8

3641752 Box 1
1752
(1) Top Front 1 x 4 x 38-1/2"
3641758 Box 1
1758
(1) Top Back 1 x 4 x 38-1/2"
3641759 Box 1
1759
(1) SW Floor 1 x 6 x 26-7/8"
3641753 Box 1
1753
(1) Top End 1 x 4 x 26-7/8"
3641754 Box 1
1754
(1) Lower Back Wall 1 x 4 x 31-1/2"
3641750 Box 1
1750
(1) Tarp Support 1 x 2 x 26-7/8"
3641751 Box 1
1751
(1) Centre Divider 2 x 2 x 38"
WOOD CHART
1" x 5½"
"
⅝" x 5
1" x 2" ⅜
⅝" x 1
"
⅜
⅝" x 3
⅝" x 4½"
"
⅜
Part Identification (Reduced Part Size)
Actual Size
1½" x 5⅜"
1⅜" x 3⅜"
1⅜" x 2½"
1½" x 1½"
1" x 3½"
1" x 4½"
2" x 6"
2" x 4"
2" x 3"
2" x 2"
5/4" x 4"
5/4" x 5"
5/4" x 6"
1" x 6"
1" x 5"
1" x 4"
Nominal Size
3641757 Box 1
(1) Wall Mount 2 x 4 x 40-3/4"
1757
3641755 Box 1
1755
(1) SW Support 5/4 x 4 x 40-1/2"
3641756 Box 1
(1) SW Upright 2 x 4 x 44"
1756
3641760 Box 1
1760
(1) Floor 1 x 6 x 26-7/8"
3641761 Box 1
1761
(1) Side Joist 2 x 2 x 34-3/4"
3641762 Box 1
1762
(1) Floor Back 5/4 x 4 x 38-5/8"
9

3641766 Box 1
1766
(3) Corner Block 2 x 3 x 4-1/2"
3641771 Box 1
1771
(4) Post 2 x 4 x 74"
3650318 Box 1
(4) Ground Stake 1-1/4 x 1-1/2 x 14"
0318
3641770 Box 1
1770
(1) SW Ground 1 x 5 x 60-1/4"
Part Identification (Reduced Part Size)
4
I.D.
3641765 Box 1
1765
(2) Rock Rail 2 x 3 x 42-3/4"
3641769 Box 1
1769
(1) Ground Side 1 x 5 x 42-1/4"
3641768 Box 1
1768
(1) Lower Back 1 x 5 x 38-1/2"
3641764 Box 1
1764
(1) Floor Front 2 x 3 x 38-1/2"
3641763 Box 1
1763
(1) Floor Joist 5/4 x 2 x 38-1/2"
3641767 Box 1
1767
(1) Lower Front 1 x 6 x 39-3/4"
9
3644919 Box 1
4919
(1) Sw Rail Block 2 x 4 x 5-3/8"
10
1X 5790524 Rocks Add
On
Hardware Bag (4pk)
x4 x4
x4
x4
x4

H6
(2) Hex Bolt 1/4 x 4 3/4 9277243
1/4" Lock Washer - 1/4" Flat Washer - 1/4" T-Nut
H5
(2) Hex Bolt 1/4 x 4 1/2" 9277242
1/4" Lock Washer - 1/4" Flat Washer - 1/4" T-Nut
1/4" Lock Washer - 1/4" Flat Washer - 1/4" T-Nut
(1) Hex Bolt 1/4 x 2 3/4" 9277223
H11
G1
(4) Hex Bolt 5/16 x 1 1/2"
5/16" Lock Washer - 5/16" Flat Washer - 5/16" T-Nut 9277312
G5
(5) Hex Bolt 5/16 x 4 1/2" 9277342
5/16" Lock Washer - 5/16" Flat Washer - 5/16" T-Nut
H7
(4) Hex Bolt 1/4 x 5 1/2" 9277252
1/4" Lock Washer - 1/4" Flat Washer - 1/4" T-Nut
PB2
9274211
(2) Pan Bolt 1/4 x 1 1/4"
Lock Washer 1/4" Flat Washer 1/4" T-Nut
G4
(4) Hex Bolt 5/16 x 4" 9277340
5/16" Lock Washer - 5/16" Flat Washer - 5/16" T-Nut
H2
(22) Hex Bolt 1/4 x 2" 9277220
1/4" Lock Washer - 1/4" Flat Washer - 1/4" T-Nut
Hardware Identification (Actual Size)
H3
(2) Hex Bolt 1/4 x 2 1/2" 9277222
1/4" Lock Washer - 1/4" Flat Washer - 1/4" T-Nut
H1
(2) Hex Bolt 1/4 x 1 1/2" 9277212
1/4" Lock Washer - 1/4" Flat Washer - 1/4" T-Nut
H8
(1) Hex Bolt 1/4 x 4 1/4" 9277241
1/4" Lock Washer - 1/4" Flat Washer - 1/4" T-Nut
11

Hardware Identification (Actual Size)
S2
(59) Flat Head Screw #8 x 1 1/2" (52042512)
LS3
G8
S3
(12) Flat Head Screw #8 x 2 1/2" (52042522)
S4
(6) Flat Head Screw #8 x 3" (52042530)
S5
(22) Pan Screw #8 x 1/2" (9264504)
(38)
1/4" T-Nut
(9285200)
(13)
5/16" T-Nut
(9285300)
(38)
1/4" Lock Washer
(9253200)
(17)
5/16" Flat Washer
(9251300)
(13)
5/16" Lock Washer
(9253300)
(41)
1/4" Flat Washer
(9251200)
(12)
3/16" Flat Washer
(9251100)
S1
(24) Flat Head Screw #8 x 1 1/8" (52042514)
9262230
(3) Lag Screw 1/4 x 3" -1/4" Flat Washer
(1 pk of 4)
Bolt Thru Swing
Hangers
(3202000)
S10
(16) Pan Screw #8 x 1" (9264510)
(2)
5/16" Lock Nut
(9283300)
9277320
(2) Hex Bolt 5/16 x 2"
2-5/16" Flat Washer, 1- 5/16" Lock Nut
(18)
#8 Flat Washer
(9251500)
S7
(14) Pan Screw #12 x 2" (9264620)
S15
(10) Pan Screw #8 x 1-3/4" (52042513)
112

13
Step 1: Inventory Parts - Read This Before Starting Assembly
• Please refer to Page 6 for proper hardware assembly.
• Each step indicates which bolts and/or screws you will need for assembly, as well as
any at washers, lock washers, t-nuts or lock nuts.
A. This is the time for you to inventory all your hardware, wood and accessories,
referencing the parts identication sheets. This will assist you with your assembly.
• The wood pieces will have the four digit key number stamped on the ends of the
boards. The wood pieces are referenced throughout the instructions with this number.
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 4)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 5)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 6)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 1)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 2)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 3)
MODEL NUMBER: F24145
TRACKING NUMBER (from ID Plaque):
B. If there are any missing or damaged pieces or you need assistance with
assembly please contact the consumer relations department directly. Call us
before going back to the store.
C. Read the assembly manual completely, paying special attention to ANSI warnings;
notes; and safety/maintenance information.
D. Before you discard your cartons fill out the form below.
•The carton I.D. stamp is located on the end of each carton.The tracking number is
located on the KidKraft ID Plaque (9320374).
•Please retain this information for future reference. You will need this information if you
contact the Consumer Relations Department.
[phone]
[email protected]
For online parts replacement visit
https://parts.kidkraft.eu/
1.800.933.0771 or 972.385.0100
[email protected]
[email protected]
For online parts replacement visit
https://parts.kidkraft.com/

Step 1: Swing Beam Assembly
Warning: For your childs safety,
orientate the swing hangers as
shown to ensure your swing will
have proper swing motion when
installed. Failure to do so could
result in premature failure of the
swing hanger or swing chain.
Hex Bolt Assembly
Lock
Washer T- Nut
Flat
Washer
He x
Bolt
Bolt Thru Hangers
1773
1772
Fig. 1.1
Fig. 1.2
Front
Back
Front
Back
1773
1772
Make sure triangle is
tight against beam
Important!
Fort End Side
(No Overhang)
Important!
Swing End
(With Overhang)
Triangle Plates
1 x CE SW Beam Front 2 x 6 x 69-1/2”
1 x CE SW Beam Back 2 x 6 x 69-1/2”
1773
1772
Hardware
Wood Parts
Fig. 1.3
Other Parts
4 x Bolt Thru Swing Hangers
1 x Triangle Plates (pkg of 4)
x4
x4
A:Inthemiddleholesof(1772)CE
SWBeamBackinstall2BoltThru
SwingHangersmakingsurethe
swinghangersareorientedinthe
directionshowning.1.3tomaintain
properswingmotion.
B:Intheendholesof(1773)CESW
BeamFrontinstall2Bolt-ThruSwing
Hangersmakingsuretheswing
hangersareorientedinthedirection
showning.1.3tomaintainproper
swingmotion.
D: Attach1TrianglePlatetoeachendofboththe(1773)CESWBeamFrontand(1772)CESWBeamBackusing
1(G1)5/16x1-1/2”HexBolt(withlockwasher,atwasherandt-nut)perTrianglePlateintheholeindicateding.
1.2.Correct hole usage is very important. Refertog1.2forcorrectplacementofHexBolts.
C:Attach1(H7)1/4x5-1/2”Hex
Bolt(withlockwasher,atwasher
andt-nut)totheendsofeach(1772)
CESWBeamBackand(1773)CE
SWBeamFront.Theboltsdonot
attachtoanything,butMUSTbein-
stalledtothebeamstopreventsplit-
tingandcheckingofwood.(g.1.1)
4 x 5/16 x 1-1/2” Hex Bolt
(5/16” lock washer, 5/16” at washer and 5/16” t-nut)
4 x 1/4 x 5-1/2” Hex Bolt
(1/4” lock washer, 1/4” at washer and 1/4” t-nut)
G1
H7
H7
G1
14

Step 2: Swing End Assembly
1756
Hex Bolt Assembly
Lock
Washer T- Nut
Flat
Washer
He x
Bolt
1749
1755
1749
Fig 2.1
2 x SW Post 2 x 4 x 79-1/2”
1 x SW Upright 2 x 4 x 44”
1 x SW Support 5/4 x 4 x 40-1/2”
1749
1756
Hardware
Wood Parts
2 x 5/16 x 4” Hex Bolt
(5/16” lock washer, 5/16” at washer, and 5/16” t-nut)
3 x 5/16 x 4-1/2” Hex Bolt
(5/16” lock washer, 5/16” at washer, and 5/16” t-nut)
G4
G5
1755
G4
G5
A:Attach2(1749)SWPoststo(1756)SWUprightusing2(G4)5/16x4”HexBolts(withlockwasher,atwasher
andt-nut).(g.2.1)
B:Attach(1755)SWSupporttoboth(1749)SWPostsand(1756)SWUprightusing3(G5)5/16x4-1/2”Hex
Bolts(withlockwasher,atwasherandt-nut).(g.2.1)
15

Step 3: Swing Beam
Fig. 3.1
Sidewith
Overhang
H8
1772
1773
Fig. 3.2
Fig. 3.3
Fig. 3.4
4919
G5
G8
1 x SW Rail Block 2 x 4 x 5-3/8”
4919
Hardware
Wood Parts 1 x 1/4 x 4-1/4” Hex Bolt
(1/4” lock washer, 1/4” at washer, 1/4” t-nut)
1 x 5/16 x 4-1/2” Hex Bolt
(5/16” lock washer, 5/16” at washer, 5/16” t-nut)
1 x 5/16 x 2” Hex Bolt
(5/16” at washer x 2, 5/16” lock nut)
H8
G5
A:Place(4919)SWRailBlockinthecentrebetween(1773)CESWBeamFrontand(1772)CESWBeamBack
andattachbeamswith1(H8)1/4x4-1/4”HexBolt(withatwasher,lockwasherandt-nut).(g.3.1&3.2)
B:AttachSwingBeamAssemblytothesideoftheSwingEndAssemblywiththeoverhang(g.3.3)using1(G5)
5/16x4-1/2”HexBolt(withlockwasher,atwasherandt-nut)inthetopholeofTrianglePlateand1(G8)5/16x
2”HexBolt(with2atwashersandlocknut)inthebottomholeofTrianglePlate.(g.3.3)MakesureSwingEnd
Assemblyaresoutatanangle.(g3.4)
Hex Bolt Assembly
Lock
Washer T- Nut
Flat
Washer
He x
Bolt
G8
16

1 x SW Top 1 x 4 x 26-7/8”
Step 4: Swing Side Assembly
Note:Pre-drillallholesusing
a1/8”drillbitbeforeinstalling
thelagscrews.
1759
1771
1748
1770
1757
H2
0369
2 x Post 2 x 4 x 74”
1 x SW Ground 1 x 5 x 60-1/4”
1 x SW Floor 1 x 6 x 26-7/8”
1 x Lower Diagonal 2 x 3 x 37”
1 x Wall Mount 2 x 4 x 40-3/4”
1771
Hardware
Wood Parts
11 x 1/4 x 2” Hex Bolt
(1/4” lock washer, 1/4” at washer, 1/4” t-nut)
2 x 5/16 x 4” Hex Bolt
(5/16” lock washer, 5/16” at washer, 5/16” t-nut)
1 x 1/4 x 3” Lag Screw (with 1/4” at washer)
1770
1759
0369
1757
LS3
Hex Bolt Assembly
Lock
Washer T- Nut
Flat
Washer
He x
Bolt
PredrillPilotHolesforLagScrew
Lag
Screw
Flat
Washer
Predrill1/8”
pilothole
Usefactorydrilled
holeasaguide
Fig. 4.1
Noticehole
location
H2
H2
LS3
H2
G4
H2
H2
1748
G4
Fig. 4.2
A:To2(1771)Postsattach(1770)SWGroundand(1759)SWFloorusing4(H2)1/4x2”HexBolts(withlock
washer,atwasherandt-nut)ineachboard.Be sure to keep bolts loose. (g.4.1)
1759
1770
1771
G4
B: Attach(1748)SWToptoeach(1771)Postwith2(H2)1/4x2”HexBolts(withlockwasher,atwasherand
t-nut)HexBoltsaretobeinstalledfromthebackoftheassembly.Be sure to keep bolts loose. (g.4.2)
C:Makesureassemblyissquareandthenfasten(0369)LowerDiagonalto(1770)SWGroundatanangleusing
1(H2)1/4x2”HexBolt(withlockwasher,atwasherandt-nut)andto(1771)Postusing1(LS3)1/4x3”Lag
Screw(withatwasher).(g4.2).
D: Attach(1757)WallMountto(1759)SWFloorand(1748)SWTopwith2(G4)5/16x4”HexBolts(withlock
washer,atwasherandt-nut).(g.4.2)
E: Tightenallbolts.
H2
17

Step 5: Wall Side Assembly
1769
1771
1760
H2
Hex Bolt Assembly
Lock
Washer T- Nut
Flat
Washer
He x
Bolt
H2
H2
H2
1753
2 x Post 2 x 4 x 74”
1 x Ground Side 1 x 5 x 42-1/4”
1 x Floor 1 x 6 x 26-7/8”
1 x Corner Block 2 x 3 x 4-1/2”
1 x Top End 1 x 4 x 26-7/8”
1771
Hardware
Wood Parts
10 x 1/4 x 2” Hex Bolt
(1/4” lock washer, 1/4” at washer, 1/4” t-nut)
2 x #8 x 1-1/2” Wood Screw
H2
1769
1760
1766
1753
S2
A:To2(1771)Postsattach(1760)Floorand(1769)GroundSidewith4(H2)1/4x2”Bolts(withlockwasher,
atwasherandt-nut)perboard.(g.5.1)
B: Attach(1753)TopEndtoeach(1771)Postwith2(H2)1/4x2”HexBolts(withlockwasher,atwasherand
t-nut).TheseHexBoltsaretobeinstalledfromthebackoftheassembly.(g.5.1)
C:Attach(1766)CornerBlockushtoangledextensionof(1769)GroundSidewith2(S2)8x1-1/2”Wood
Screwsasshowning.5.2.
Fig. 5.2
Fig. 5.1
S2 1766
Fig. 5.3
Noticeholetowardsback
Back
1753
H2
1769
18

Fig. 6.1
1752
S7
1764
Step 6: Front Frame Assembly
S7
H6
H6
1 x Floor Front 2 x 3 x 38-1/2”
1 x Top Front 1 x 4 x 38-1/2”
1764
Hardware
Wood Parts
2 x 1/4 x 4-3/4” Hex Bolt
(1/4” lock washer, 1/4” at washer, 1/4” t-nut)
4 x #12 x 2” Pan Screw (with 3/16” at washer)
H6
1752
S7
Hex Bolt Assembly
Lock
Washer T- Nut
Flat
Washer
He x
Bolt
Fig. 6.2
1748
1771
1759
1760
Swingwallside
Slidewallside
Partsremoved
forclarity
1771
Noticehole
towardstop
Noticehole
towardsbottom
A: Attach(1764)FloorFrontto(1771)Postswith2(H6)1/4x4-3/4”Bolt(withatwasher,lockwasherandt-
nut).HexBoltstobeinstalledfromtheinsideoftheassembly.(g.6.2)
B:Attach(1752)TopFrontto(1771)Postswith4(S7)12x2”PanScrews(with3/16”atwasher).(1752)Top
Frontshouldbeushtothetopofeach(1771)Post.(g.6.1&6.2)
19

Step 7: Rock Rail Assembly
Fig. 7.1
1765
S3
1766
Hardware
2 x #8 x 2-1/2” Wood Screw
2 x #8 x 1-1/2” Wood Screw
2 x #8 x 1-3/4” Wood Screw
S3
A:Attach(1766)CornerBlock1/2”frombottomof(1765)RockRailwith2(S3)8x2-1/2”WoodScrewsasshown
ing.7.1.
B: Makesureassemblyissquareandthenattach(1765)RockRailwithCornerBlockto(1764)FloorFrontwith
2(S15)#8x1-3/4”WoodScrews.Topof(1765)RockRailanglededgeshouldbeushtothetopof(1764)Floor
Front.(g.7.2&7.3)
C:Attach(1770)SWGroundto(1765)RockRailwith2(S2)#8x1-1/2”WoodScrewsasshowning.7.2&7.4.
x2
S2
Fig. 7.2
Fig. 7.3
1765
1764
1770
1765
1764
1770
Flush
Fig. 7.4
1765
1 x Corner Block 2 x 3 x 4-1/2”
1 x Rock Rail 2 x 3 x 42-3/4”
1766
Wood Parts
1765 S2
1/2”
S15
S15
20