KidKraft COZY ESCAPE PLAYHOUSE F29045 User manual

Table of Contents
Warnings and Safe Play Instructions..........pg. 2
Protective Surfacing Guidelines. . . . . . . . . . . . . . . pg. 3
Instructions for Proper Maintenance .........pg. 4
About Our Wood – Limited Warranty.........pg. 5
Keys to Assembly Success ....................pg. 6
Part ID ................................... pg. 8-19
Step-By-Step Instructions ...................pg. 20
Installation of I.D./Warning Plaque......Final Step
Rev 05/08/2019
9409045
KidKraft, Inc.
4630 Olin Road
Dallas, Texas 75244 USA
[email protected]
[email protected]
1.800.933.0771
972.385.0100
For online parts replacement visit
https://parts.kidkraft.com/
KidKraft Netherlands BV
Olympisch Stadion 29
1076DE Amsterdam
The Netherlands
[email protected]
[phone] M-F from 09:00 to 17:30
(GMT+1)
For online parts replacement visit
https://parts.kidkraft.eu/
COZY ESCAPE PLAYHOUSE - F29045
INSTALLATION AND OPERATING INSTRUCTIONS
2 - 4 Hrs
FOR FORT
TWO PERSON
ASSEMBLY
2-4 Hrs
10 - 12 Hrs
FOR FORT & SWING
TWO PERSON
ASSEMBLY
10 - 12 Hrs
FOR FORT & SWING
1 - 2 Hrs
TUBE SLIDE
277cm 677cm
720cm
320cm
10’ 6”
7’ 25”
23’ 7.5”
20’ 1.7”
To reduce the risk of serious injury or death, you must read and follow these instrucons. Keep and
refer to these instrucons oen and give them to any future owner of this play set. Manufacturer
contact informaon provided below.
OBSTACLE FREE SAFETY ZONE - 23’ 7.5” x 20’1.7” (720 x 677 cm) area requires Protecve Surfacing. See page 3.
MAXIMUM VERTICAL FALL HEIGHT - 56-5/16” (1.43m)
CAPACITY - 11 Users Maximum, Ages 3 to 10; Weight Limit 110 lbs.
(49.9 kg) per child.
RESIDENTIAL HOME USE ONLY. Not intended for public areas such as
mul-unit residences, schools, churches, nurseries, day cares or parks.
Warning. Only for domesc use.
For Outdoor Family
Domestic Use Only
WARNING

2
Warnings and Safe Play Instructions
CONTINUOUS ADULT SUPERVISION REQUIRED. Most serious injuries and deaths on playground equipment have occurred
while children were unsupervised! Our products are designed to meet mandatory and voluntary safety standards. Complying
with all warnings and recommendations in these instructions will reduce the risk of serious or fatal injury to children using
this play system. Go over the warnings and safe play instructions regularly with your children and make certain that they
understand and follow them. Remember on-site adult supervision is required for children of all ages.
SERIOUS HEAD INJURY HAZARD
Installation over concrete, asphalt, dirt, grass, carpet
and other hard surface creates a risk of serious injury
or death from falls to the ground. Install and maintain
shock absorbing material under and around play-set as
recommended on page 3 of these instructions.
COLLISION HAZARD
Place play-set on level ground at least 2m from any
obstruction such as a garage or house, fences, poles,
trees, sidewalks, walls, landscape timbers, rocks,
pavement, planters, garden borders, overhanging
branches, laundry lines, and electrical wires. (See
OBSTACLE FREE SAFETY ZONE on cover)
CHOKING HAZARD/SHARP EDGES & POINTS
Adult assembly required. This product contains small
parts and parts with sharp edges and points. Keep parts
away from children until fully assembled.
WARNING LABEL
Owners shall be responsible for maintaining the legibility
of the warning labels.
STRANGULATION HAZARD
,seni lsehtolc,seporht iwyalpotnerdl ihcwol laREVEN•
pet leashes, cables, chains or cord-like items when using
this play-set or to attach these items to play-set.
ponchos, hoods, scarves, capes, necklaces, items with
draw-strings, cords or ties when using this play-set.
stemlehtropsroekibraewotnerdl ihcwol laREVEN•
when using this play-set.
Failure to prohibit these items, even helmets with chin
straps, increases the risk of serious injury and death to
children from entanglement and strangulation.
TIP OVER HAZARD
Choose a level location for the equipment. This can reduce
the likelihood of the play set tipping over and loose-fill
surfacing materials washing away during heavy rains.
DO NOT allow children to play on the play-set until the
assembly is complete and the unit is properly anchored.
Never add extra length to chain or rope. The chains or ropes
provided are the maximum length designed for the swinging
element(s).
WARNING
eeS. t es-ya l pruoyfosno i t a t imi ly t i capacevresbO
front cover.
gn i so l cnet oo f l l u fdnagn i t t fil l ewh t iwne rd l i hcsse rD
footwear.
retnecehtnithgiewl lufr iehtht iwt isotnerdl ihchcaeT
of the swing seat to prevent erratic swing motion or
falling off.
, gn i ss im; doowdekcarcronekorb, dere tn i l psrofkcehC
loose, or sharp edged hardware. Replace, tighten and or
sand smooth as required prior to playing.
n i ahc, s r edda lepor, seporgn i bmi l cdednepsust ah ty f i r eV
or cable are secured at both ends and cannot be looped
back on itself as to create an entanglement hazard.
r eh t odnaed i l seh tkcehc, syadt ohrodnaynnusnO
plastic rides to assure that they are not very hot as to
cause burns. Cool hot slide and rides with water and wipe
dry prior to using.
r aewt oo f l eehroeo tnepor aewo tne rd l i hcwo l l at onoD
like sandals, flip–flops or clogs.
dniheb,neewteb, tnorfni,klawotnerdl ihcwol latonoD
or close to moving rides.
poolroseporrosniahcgniwstsiwtnerdl ihcteltonoD
them over the top support bar. This may reduce the
strength of the chain or rope and cause premature failure.
.noi tomnierayehtel ihwsedi rf fotegnerdl ihcteltonoD
. t ews i t inehwt nemp i uqenogn i bmi l ct imr ept onoD
an i t nemp i uqef oesur oy a l phguo rt imr ept onoD
manner for which it was not intended. Standing on or
jumping from the roof, elevated platforms, swings,
climbers, ladders or slide can be dangerous.
.staesrosedi rytpmegniwsotnerdl ihcwol latonoD
rotsrfidaehed i l snwodogo tne rd l i hcwo l l at onoD
run up slide.
WARNING – Safe Play Instructions
Orientate slide such that it gets the least amount of exposure
to the sun.

3
One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing
protective surfacing under and around your play equipment. The protective surfacing should be applied to a depth that is suitable
for the equipment height in accordance with ASTM F1292. There are different types of surfacing to choose from; whichever
product you select, follow these guidelines:
Loose-Fill Materials
• Maintain a minimum depth of 9 inches of loose-fill materials such as wood mulch/chips, engineered wood fiber (EWF), or
shredded/recycled rubber mulch for equipment up to 8 feet high; and 9 inches of sand or pea gravel for equipment up to 5 feet
high. NOTE: An initial fill level of 12 inches will compress to about a 9-inch depth of surfacing over time. The surfacing will also
compact, displace, and settle, and should be periodically raked and refilled to maintain at least a 9-inch depth.
• Use a minimum of 6 inches of protective surfacing for play equipment less than 4 feet in height. If maintained properly, this
should be adequate. (At depths less than 6 inches, the protective material is too easily displaced or compacted.)
NOTE: Do not install home playground equipment over concrete, asphalt, or any other hard surface. A fall onto a hard surface
can result in serious injury to the equipment user. Grass and dirt are not considered protective surfacing because wear and
environmental factors can reduce their shock absorbing effectiveness. Carpeting and thin mats are not adequate protective
surfacing. Ground level equipment -- such as a sandbox, activity wall, playhouse or other equipment that has no elevated play
surface -- does not need any protective surfacing.
• Use containment, such as digging out around the perimeter and/or lining the perimeter with landscape edging. Don’t forget to
account for water drainage.
• Periodically rake, check and maintain the depth of the loose-fill surfacing material. Marking the correct depth on the play
equipment support posts will help you to see when the material has settled and needs to be raked and or replenished. Be sure to
rake and evenly redistribute the surfacing in heavily used areas.
• Do not install loose fill surfacing over hard surfaces such as concrete or asphalt.
Poured-In-Place Surfaces or Pre-Manufactured Rubber Tiles
You may be interested in using surfacing other than loose-fill materials - like rubber tiles or poured-in-place surfaces.
• Installations of these surfaces generally require a professional and are not “do-it yourself” projects.
• Review surface specifications before purchasing this type of surfacing. Ask the installer/manufacturer for a report showing that
the product has been tested to the following safety standard: ASTM F1292 Standard Specification for Impact Attenuation of
Surfacing Materials within the Use Zone of Playground Equipment. This report should show the specific height for which the
surface is intended to protect against serious head injury. This height should be equal to or greater than the fall height - vertical
distance between a designated play surface (elevated surface for standing, sitting, or climbing) and the protective surfacing
below - of your play equipment.
• Check the protective surfacing frequently for wear.
Placement
Proper placement and maintenance of protective surfacing is essential. Refer to diagram on front cover. Be sure to;
• Extend surfacing at least 2m from the equipment in all directions.
• For to-fro swings, extend protective surfacing in front of and behind the swing to a distance equal to twice the height of the top bar
from which the swing is suspended.
• For tire swings, extend surfacing in a circle whose radius is equal to the height of the suspending chain or rope, plus 6 feet in all
directions.
From the CPSC Outdoor Home Playground Safety Handbook. At http://www.playgroundregs.com/resources/CPSC%20324.pdf
Protective Surfacing - Reducing Risk of Serious Head Injury From Falls.
2H 2H
H
Denotes Use Zone with Protective Surfacing
Use Zone for Single-Axis Swings
6 ft.
6 ft.
6 ft.
6 ft.
Denotes Use Zone with Protective Surfacing
Use Zone for Multi-Axis Swings
6 ft. 6 ft.
6 ft.
L

4
Instructions for Proper Maintenance
HARDWARE:
Check metal parts for rust. If found,
sand and repaint using a non-lead
paint complying with 16 CFR 1303.
Inspect and tighten all hardware. On
wood assemblies DO NOT OVER-
TIGHTEN as to cause crushing and
splintering of wood.
Check for sharp edges or protruding screw threads, add
washers if required.
SHOCK ABSORBING SURFACING:
Check for foreign objects. Rake and check depth of loose
fill protective surfacing materials to prevent compaction
and maintain appropriate depth. Replace as necessary.
(See Protective Surfacing, page 3)
GROUND STAKES (ANCHORS):
Check for looseness, damage or deterioration. Should
firmly anchor unit to ground during use. Re-secure and
or replace, if necessary.
SWING HANGERS:
Check that bolts are secure and tight. Quick clips should
be completely closed and threaded clips screwed tight.
If squeaking occurs lubricate bushings with oil or WD-40®.
SWINGS, ROPES AND RIDES:
Reinstall if removed during cold season. Check all
moving parts including swing seats, ropes, chains and
attachments for wear, rust and other deterioration.
Replace as needed.
Check that ropes are tight, secure at both ends and
cannot loop back as to create an entrapment.
WOOD PARTS:
Check all wood members for deterioration, structural
damage and splintering. Sand down splinters and replace
deteriorated wood members. As with all wood, some
checking and small cracks in grain is normal.
Unprotected, they will appear weathered over time.
Periodic application of an exterior water repellent or stain
(water-based) will help improve appearance and life.
Your KidKraft Play System is designed and constructed of quality materials with your child’s safety in mind. As with all outdoor
products used by children, it will weather and wear. To maximize the enjoyment, safety and life of your Play Set, it is important
that you, the owner, properly maintain it.
Check the following at the beginning of the play season:
HARDWARE:
Inspect for tightness. Must be firmly against, but not
crushing the wood. DO NOT OVER-TIGHTEN.
This will cause splintering of wood.
Check for sharp edges or protruding screw threads.
Add washers if required.
SHOCK ABSORBING SURFACING:
Rake and check depth of loose fill protective surfacing
materials to prevent compaction and maintain appropriate
depth. Replace as necessary.
(See Protective Surfacing, page 3)
Check twice a month during play season:
SWING HANGERS:
Check that they are secure and orientated correctly. Hook
should rotate freely and perpendicular to support beam.
If squeaking occurs lubricate bushings with oil or WD-40®.
SWINGS AND RIDES:
Check swing seats, all ropes, chains and attachments for
fraying, wear, excessive corrosion or damage.
Replace if structurally damaged or deteriorated.
Check once a month during play season:
SWINGS AND RIDES:
To prolong their life, remove swings and store inside
when outside temperature is below 32°F/0°C. Below
freezing, plastic parts may become more brittle.
SHOCK ABSORBING SURFACING:
Rake and check depth of loose fill protective surfacing
materials to prevent compaction and maintain appropriate
depth. Replace as necessary.
(See Protective Surfacing, page 3)
Check at the end of the play season:
If you dispose of your play set: Please disassemble and dispose of your unit so that it does not create any unreasonable hazards
at the time it is discarded. Be sure to follow your local waste ordinances.
Use an extra
Flat Washer
If Bolt protrudes
beyond T-Nut

5
About Our Wood
KidKraft Premium Play Systems uses only premium playset lumber, ensuring the safest product for your children’s use. Although we
take great care in selecting the best quality lumber available, wood is still a product of nature and susceptible
to weathering which can change the appearance of your set.
What causes weathering? Does it affect the strength of my Play System?
One of the main reasons for weathering is the effects of water (moisture); the moisture content of the wood at the surface is
different than the interior of the wood. As the climate changes, moisture moves in or out of the wood, causing tension which can
result in checking and or warping. You can expect the following due to weathering. These changes will not affect the strength of
the product:
1. Checking is surface cracks in the wood along the grain. A post (4” x 4”)will experience more checking than a board (1” x 4”)
because the surface and interiormoisture content will vary more widely than in thinner wood.
2. Warping results from any distortion (twisting, cupping) from the original plane ofthe board and often happens from rapid
wettingand drying of the wood.
3. Fading happens as a natural change in the wood coloras it is exposed tosun-light and will turn a grey over time.
How can I reduce the amount of weathering to my Play System?
At the factory we have coated the wood with a water repellent or stain. This coating decreases the amount of water absorption
during rain or snow thus decreasing the tension in the wood. Sunlight will break down the coating, so we recommend applying a
water repellent or stain on a yearly basis (see your local stain and paint supplier for a recommended product).
Most weathering is just the normal result of nature and will not affect safe play and enjoyment for your child. However if you are
concerned that a part has experienced a severe weathering problem please call our consumer relations department for further assistance.
Complete and mail registration card to receive important product notifications and assure prompt
warranty service.
5 Year Limited Warranty
KidKraft warrants that this product is free from defect in materials and workmanship for a period of one
year from the original date of purchase. In addition, lumber is warranted for 5 years against structural
failure due to rot and insect damage. All other parts, such as hardware, swings, rides, accessories, and
slides carry a one-year warranty only.
This warranty applies to the original owner and registrant and is non-transferable.
Regular maintenance is required to assure the integrity of your Play System. This warranty does not
cover any inspection cost.
This Limited Warranty does not cover:
•Labor for replacement of any defective item(s);
•Incidental orconsequential damages;
•Cosmetic defects whichdo not affect performance or integrity;
•Vandalism; improper use or installation; acts of nature;
•Minortwisting, warping, checking,or any other natural occurring properties of wood that do not
affect performance or integrity.
KidKraft products have been designed for safety and quality. Any modifications made to the original
product could damage the structural integrity of the unit leading to failure and possible injury.
Kidkraft cannot assume any responsibility for modified products. Furthermore, modification voids
any and all warranties.
This product is warranted for RESIDENTIAL USE ONLY. Under no circumstance should a
KidKraft Play System be used in public settings such as schools, churches, playgrounds, parks, day
cares and the like. Such use may lead to product failure and potential injury. Any and all public use
will void this warranty.
KidKraft disclaims all other representations and warranties of any kind, express or implied.
This Warranty gives you specific legal rights. You may have otherrights as well which vary from state to state or
province to province. This warranty excludes all consequential damages, however, some states do notallow the
limitation or exclusion ofconsequential damages, andtherefore this limitation may not apply to you.

6
Part Identication Key
On each page, you will nd the parts
and quantities required to complete
the assembly step illustrated on that
page. Here is a sample.
Symbols
Throughout these instructions symbols are provided as important reminders for proper and safe assembly.
Proper Hardware Assembly
Lag screws require drilling pilot
holes to avoid splitting wood. Only a
at washer is required. For ease of
installation liquid soap can be used
on all lag-type screws.
For bolts, tap T-Nut into hole with
hammer. Insert the hex bolt through
lock washer rst then at washer
then hole. Because the assemblies
need to be squared do not completely
tighten until instructed. Pay close
attention to diameter of the bolts.
5/16” is slightly larger than 1/4”.
Note: Wafer head bolts with blue lock
tight or a bolt with a Ny-Lok nut do
NOT require a lock washer.
Once the assembly is tightened, watch for exposed
threads. If a thread protrudes from the T-Nut, remove
the bolt and add washers to eliminate this condition.
Extra washers have been provided for this purpose.
This identies information that requires
special attention. Improper assembly could
lead to an unsafe or dangerous condition.
Where this is shown, 2 or 3
people are required to safely
complete the step. To avoid
injury or damage to the
assembly make sure to
get help!
Check that assembly is square
before tightening bolts.
Use a measuring tape to
assure proper location.
Check that set or assembly is properly level
before proceeding.
Pre-drill a pilot hole
before fastening screw
or lag to prevent
splitting of wood.
This indicates time to tighten bolts, but
not too tight! Do not crush the wood.
This may create splinters and cause
structural damage.
Use
Help
Use
Help
Measure
Distance
Square
Assembly
Use
Level
Pre-drill 1/8” & 3/16” Bit
Tighten
Bolts
No Yes
CAUTION – Protrusion Hazard
Keys to Assembly Success
Tools Required
• Tape Measure
• Carpenters Level
• Carpenters Square
• Claw Hammer
• Standard or Cordless Drill
• #1, #2 & #3 Phillips
or Robertson Bits
or Screwdriver
• Ratchet with extension
(1/2” & 9/16” sockets)
• Open End Wrench
(7/16”, 1/2” & 9/16”)
• Adjustable Wrench
• 1/8” & 3/16” Drill Bits
• Pencil
• 3/16” Hex Key
• 8’ Step Ladder
• Safety Glasses
• Adult Helpers
Quantity Key Number Part Description,
Part Size
2X 012 Post 2 x 4 x 83”
Use an extra
Flat W asher
If Bolt protrudes
beyond T-Nut
Lag Screw
Flat Washer
Lag Assembly
Before mounting Lag Screw,
use factory drilled holes as
guides to drill 1/8” pilot holes
Hex Bolt Bolt Assembly
T-Nut
(Hammer into place)
Do not crush wood!
Lock
Washer
Flat
Washer

7
Part Quantity Key Number Part Description Part Size
2X 012 Post 2 x 4 x 83”
Your Key To Quick Assembly
SAVE TIME - TIP #1:
Wood parts are found in Box 2, 3, 4 & 5. Open each box with wood parts and
look for the Key Number stamped on the end of the wood part (see chart below).
Sort each wood part into the different assembly steps.
SAVE TIME - TIP #2:
In addition to the key number stamp, you can also identify the wood parts by
using the Parts Identication pages in the manual.
HARDWARE:
The majority of each hardware part comes packed in a separate bag so
you do not need to sort the hardware. Each assembly step indicates which
hardware (bolt, screw, washer etc.) you will require to complete the step.
Step Step Step

8
1pc. - 9464 - 31.8 x 76.2 x 1362.2 - Floor Support A - Box 1 - 3569464
1-1/4 x 3 x 53-5/8"
1pc. - 9465 - 38.1 x 38.1 x 1292.4 - Side Joist 1 - Box 1 - 3569465
1-1/2 x 1-1/2 x 50-7/8"
2pc. - 9462 - 38.1 x 38.1 x 1355.8 - Side Joist - Box 1 - 3569462
1-1/2 x 1-1/2 x 53-3/8"
11pc. - 9463 - 15.9 x 133.4 x 863.8 - Floor Board - Box 2 - 3589463
5/8 x 5-1/4 x 34"
4pc. - 9460 - 31.8 x 63.5 x 1355.8 - Floor Joist - Box 1 - 3569460
4pc. - 9461 - 31.8 x 63.5 x 796.9 - Floor Joist Short - Box 1 - 3569461
1-1/4 x 2-1/2 x 31-3/8"
1pc. - 9518 - 15.9 x 88.9 x 863.8 - Floor Board B - Box 2 - 3589518
5/8 x 3-1/2 x 34"
1pc. - 9466 - 38.1 x 38.1 x 1419.3 - Side Joist 2 - Box 1 - 3569466
1-1/2 x 1-1/2 x 55-7/8"
2pc. - 9468 - 15.9 x 82.6 x 498.2 - Floor Board Short 1 - Box 1 - 3589468
5/8 x 3-1/4 x 19-39/64"
11pc. - 9467 - 15.9 x 114.3 x 498.2 - Floor Board Short - Box 2 - 3589467
5/8 x 4-1/2 x 19-39/64"
1pc. - 9469 - 31.8 x 76.2 x 1425.7 - Floor Support - Box 1 - 3569469
1-1/4 x 3 x 56-1/8"
2pc. - 9470 - 25.4 x 50.8 x 317.6 - Counter Brace - Box 1 - 3589470
1 x 2 x 12-1/2"
4pc. - 9471 - 25.4 x 50.8 x 209.5 - Counter Joist - Box 1 - 3589471
1 x 2 x 8-1/4"
1pc. - 9472 - 15.9 x 69.9 x 817.6 - Counter Front - Box 1 - 3589472
5/8 x 2-3/4 x 32-3/16"
1pc. - 9473 - 15.9 x 82.6 x 817.6 - Counter Back - Box 1 - 3589467
5/8 x 3-1/4 x 32-3/16"
1pc. - 9474 - 15.9 x 31.8 x 817.6 - Counter Top - Box 1 - 3589474
5/8 x 1-1/4 x 32-3/16"
2pc. - 9476 - 15.9 x 50.8 x 175.7 - Counter Side - Box 2 - 3589467
5/8 x 2 x 6-59/64"
2pc. - 9475 - 15.9 x 85.7 x 212.7 - Counter Mid Top - Box 2 - 3589475
5/8 x 3-3/8 x 8-3/8"
1pc. - 9477 - 31.8 x 63.5 x 609.1 - Supporting Diagonal - Box 1 - 3569477
1-1/4 x 2-1/2 x 23-63/64"
1-1/4 x 2-1/2 x 53-3/8"
Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size)

9
1pc. - 9478 - 34.9 x 69.9 x 1309.1 - Left Rail - Box 2 - 3589478
1-3/8 x 2-3/4 x 51-17/32"
1pc. - 9479 - 34.9 x 69.9 x 1309.1 - Right Rail - Box 2 - 3589479
1-3/8 x 2-3/4 x 51-17/32"
1pc. - 9481 - 15.9 x 82.6 x 532 - RW-AL Suport - Box 1 - 3589481
5/8 x 3-1/4 x 20-15/16"
1pc. - 9482 - 15.9 x 82.6 x 532 - RW-AL Suport A - Box 1 - 3589482
5/8 x 3-1/4 x 20-15/16"
1pc. - 9483 - 31.8 x 63.5 x 578.1 - Diagonal - Box 1 - 3569483
1-1/4 x 2-1/2 x 22-49/64"
2pc. - 9484 - 31.8 x 63.5 x 1288 - Rail - Box 2 - 3589484
1-1/4 x 2-1/2 x 50-45/64"
7pc. - 9485 - 15.9 x 114.3 x 500 - Board Rock - Box 2 - 3589485
5/8 x 4-1/2 x 19-11/16"
2pc. - 9486 - 25.4 x 38.1 x 211.1 - Chair Gusset - Box 2 - 3589486
1 x 1-1/2 x 8-5/16"
2pc. - 9487 - 25.4 x 38.1 x 146.1 - Chair Gusset A - Box 2 - 3589487
1 x 1-1/2 x 5-3/4"
1pc. - 9488 - 25.4 x 79.4 x 471.4 - Chair Top - Box 2 - 3589488
1 x 3-1/8 x 18-9/16"
1pc. - 9489 - 25.4 x 79.4 x 471.4 - Chair Top A - Box 2 - 3589489
1 x 3-1/8 x 18-9/16"
1pc. - 9490 - 31.8 x 63.5 x 598.5 - Ground Brace - Box 1 - 3569490
1-1/4 x 2-1/2 x 23-9/16"
1pc. - 9491 - 25.4 x 63.5 x 534.9 - Ground Brace A - Box 1 - 3569491
1 x 2-1/2 x 21-1/16"
1pc. - 9492 - 31.8 x 63.5 x 698.5 - Ground Brace B - Box 1 - 3569492
1-1/4 x 2-1/2 x 27-1/2"
1pc. - 9493 - 31.8 x 76.2 x 495.3 - Ground Brace C - Box 1 - 3569493
1-1/4 x 3 x 19-1/2"
2pc. - 9494 - 31.8 x 63.5 x 2286 - Crowsnest Upright - Box 2 - 3569494
1-1/4 x 2-1/2 x 90"
2pc. - 9495 - 25.4 x 50.8 x 304.8 - Crowsnest Gusset - Box 1 - 3569495
1 x 2 x 12"
1pc. - 9522 - 15.9 x 114.3 x 500 - Board Rock - Box 2 - 3589522
5/8 x 4-1/2 x 19-11/16"
4pc. - 9480 - 25.4 x 82.6 x 492 - Ladder Gap - Box 2 - 3589480
1 x 3-1/4 x 19-3/8"
Actual Size
1½" x 1½"
1½" x 5⅜"
Nominal Size
2 x 2
2 x 6
Actual Size
1½" x 1½"
1⅜" x 2½"
1⅜" x 3⅜"
Nominal Size
2 x 2
2 x 3
2 x 4
Actual Size
1" x 3½"
1" x 4½"
1
" x 5½"
1⅜" x 2½"
Nominal Size
5/4 x 4
5/4 x 5
5/4 x 6
2 x 3
Nominal Size
1 x 5
1 x 6
5/4 x 2
5/4 x 3
5/4 x 4
Actual Size
⅝
" x 4½"
⅝
" x 5⅜"
1
" x 1⅜"
1" x 2½"
1" x 3½"
Actual Size
⅝
" x 3⅜"
⅝
" x 4½"
⅝
" x 5⅜"
Nominal Size
1 x 4
1 x 5
1 x 6
Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size)
Nominal Size
½
x 4
1 x 2
1 x 3
1 x 4
Actual Size
7
16
" x 3¼"
⅝" x 1⅜"
⅝" x 2⅜"
⅝" x 3⅜"

10
1pc. - 9497 - 31.8 x 63.5 x 534.9 - Crowsnest Short A - Box 1 - 3569497
1-1/4 x 2-1/2 x 21-1/16"
1pc. - 9498 - 31.8 x 63.5 x 566.7 - Crowsnest Short L - Box 1 - 3569498
1-1/4 x 2-1/2 x 22-5/16"
1pc. - 9499 - 31.8 x 63.5 x 1457.3 - Crowsnest Bottom - Box 2 - 3569499
1-1/4 x 2-1/2 x 57-3/8"
2pc. - 9499A - 31.8 x 63.5 x 1457.3 - Crowsnest Bottom - Box 2 - 3589499
1-1/4 x 2-1/2 x 57-3/8"
12pc. - 9500 - 19.1 x 63.5 x 558.8 - Cedar Wall - Box 2 - 3589500
3/4 x 2-1/2 x 22"
2pc. - 9501 - 31.8 x 50.8 x 1433.4 - Top Swing - Box 2 - 3569501
1-1/4 x 2 x 56-7/16"
2pc. - 9502 - 31.8 x 50.8 x 269.3 - Roof Support Upright - Box 1 - 3569502
1-1/4 x 2 x 10-39/64"
2pc. - 9503 - 31.8 x 50.8 x 865.2 - Roof Support - Box 2 - 3569503
1-1/4 x 2 x 34-1/16"
1pc. - 9504 - 31.8 x 50.8 x 1136.7 - Roof Sleeper Left - Box 2 - 3569504
1-1/4 x 2 x 44-3/4"
1pc. - 9519 - 31.8 x 50.8 x 1136.7 - Roof Sleeper Right - Box 2 - 3569519
1-1/4 x 2 x 44-3/4"
5pc. - 9511 - 25.4 x 50.8 x 1362.1 - Roof Bottom - Box 1 - 3569511
1 x 2 x 53-5/8"
1pc. - 9512 - 15.9 x 50.8 x 1425.6 - Roof Cover - Box 2 - 3569512
5/8 x 2 x 56-1/8"
1pc. - 9520 - 15.9 x 133.4 x 1425.6 - Roof Cover - Box 1 - 3569520
5/8 x 5-1/4 x 56-1/8"
1pc. - 9506 - 31.8 x 50.8 x 1374.8 - Roof Bottom A - Box 1 - 3569506
1 x 2 x 54-1/8"
1pc. - 9507 - 31.8 x 50.8 x 670.4 - Roof Sleeper Short L - Box 1 - 3569507
1-1/4 x 2 x 26-25/64"
1pc. - 9508 - 31.8 x 50.8 x 670.4 - Roof Sleeper Short - Box 1 - 3569508
1-1/4 x 2 x 26-25/64"
1pc. - 9509 - 31.8 x 50.8 x 1374.8 - Roof Bottom B - Box 2 - 3569509
1-1/4 x 2 x 54-1/8"
1pc. - 9513 - 25.4 x 63.5 x 254 - Door Stop - Box 1 - 3569513
1 x 2-1/2 x 10"
1pc. - 9514 - 31.8 x 88.9 x 617.1 - Mid Cross - Box 2 - 3569514
1-1/4 x 3-1/2 x 24-19/64"
2pc. - 9496 - 31.8 x 63.5 x 534.9 - Crowsnest Short - Box 2 - 3569496
1-1/4 x 2-1/2 x 21-1/16"

11
3pc. - 9515 - 25.4 x 63.5 x 866.8 - Table Top - Box 2 - 3589515
1 x 2-1/2 x 34-1/8"
2pc. - 9516 - 25.4 x 63.5 x 433.4 - Table Top Short - Box 1 - 3589516
1 x 2-1/2 x 17-1/16"
1pc. - 9521 - 34.9 x 76.2 x 358.1 - Gusset - Box 2 - 3569521
1-3/8 x 3 x 14-3/32"
1pc. - 9262 - Door
Box 1 - 37589262
31.8 x 400.1 x 491.8mm
1-1/4 x 15-3/4 x 19-23/64 "
1pc. - 9261 - Window Panel
Box 1 - 37569261
31.8 x 374.9 x 1362.1mm
1-1/4 x 14-49/64 x 53-5/8"
Actual Size
1½" x 1½"
1½" x 5⅜"
Nominal Size
2 x 2
2 x 6
Actual Size
1½" x 1½"
1⅜" x 2½"
1⅜" x 3⅜"
Nominal Size
2 x 2
2 x 3
2 x 4
Actual Size
1" x 3½"
1" x 4½"
1
" x 5½"
1⅜" x 2½"
Nominal Size
5/4 x 4
5/4 x 5
5/4 x 6
2 x 3
Nominal Size
1 x 5
1 x 6
5/4 x 2
5/4 x 3
5/4 x 4
Actual Size
⅝
" x 4½"
⅝
" x 5⅜"
1
" x 1⅜"
1" x 2½"
1" x 3½"
Actual Size
⅝
" x 3⅜"
⅝
" x 4½"
⅝
" x 5⅜"
Nominal Size
1 x 4
1 x 5
1 x 6
9263 & 9264 = 63.5 x 558.8 x 2286mm
9265 & 9266 = 63.5 x 866.6 x 2286mm
2-1/2 x 22 x 90"
2-1/2 x 34-1/4 x 90"
Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size)
Nominal Size
½
x 4
1 x 2
1 x 3
1 x 4
Actual Size
7
16
" x 3¼"
⅝" x 1⅜"
⅝" x 2⅜"
⅝" x 3⅜"

12
1pc. -
9263
- 63.5 x 558.8 x 2286mm
2-1/2 x 22 x 90"
Folding Panel Assembly Right A -
37569263
1pc. -
9264
- 63.5 x 558.8 x 2286mm
2-1/2 x 22 x 90"
Folding Panel Assembly Left A -
37569264
1pc. -
9265
- 63.5 x 866.6 x 2286mm
2-1/2 x 34-1/4 x 90"
Folding Panel Assembly Left B -
37569265
1pc. -
9266
- 63.5 x 866.6 x 2286mm
2-1/2 x 34-1/4 x 90"
Folding Panel Assembly Right B -
37569266
Part Identification (Reduced Part Size)

13
67pc. S3 - Wood Screw
#8 x 2-1/2"
- (52043522)
63.5mm
30pc. S4 - Wood Screw
#8 x 3"
- (52043530)
76.2mm
44pc. S7 - Pan Screw
#12 x 2"
- (52433620)
19pc. S6 - Pan Screw
#12 x 1"
- (52433610)
7pc. S10 - Pan Screw
#8 x 1"
- (52433510)
25.4mm
252pc. S20 - Wood Screw
#8 x 1-3/8"
- (52043516)
34.9mm
19pc. S0 - Truss Screw
#8 x 7/8"
- (52933505)
22.2mm
6pc. TN2 - 5/16" T- Nut
-
(54503300)
7pc. BN1 - 1/4" Barrel Nut
-
(54803200)
6.4mm
9pc. TN1 - 1/4" T - Nut
-
(54503200)
6.4mm
16pc. LW1 - 1/4" Lock Washer - (51303200)
6pc. FW2 - 5/16" Flat Washer - (51103300)
7.9mm
19pc. FW1 - 1/4" Flat Washer - (51103200)
6.4mm
7pc. FW0 - 3/16" Flat Washer - (51103100)
11pc. PB6 - Pan Bolt
1/4 x 1"
- (53413210)
6.4 x 25.4mm
65pc. LN1 -
1/4 Lock Nut
- (54303200)
8pc. FW6 - #12 Screw Bezel - (9299500)
54pc. PB1 - Pan Bolt
1/4 x 3/4"
- (53453203)
6.4 x 19.1mm
7pc. PB2 - Pan Bolt
1/4 x 1-1/4"
- (53433212)
6.4 x 31.8mm
23pc. S37 - Pan Screw
#7 x 5/8"
- (52433009)
15.9mm
34pc. S2 - Wood Screw
#8 x 1-1/2"
- (52043512)
38.1mm
83pc. S11 - Wood Screw
#8 x 2"
- (52043520)
50.8mm
22pc. S38 - Pan Screw
#7 x 1-1/8"
- (52433014)
28.6mm
8pc. H3 -
Hex Bolt 1/4 x 2-1/2"
- (53703222)
6.4 x 63.5mm
1pc. H8 -
Hex Bolt 1/4 x 4-1/4"
- (53703241)
6.4 x 108mm
6pc. WB10 -
Wafer Bolt 5/16 x 2-5/8"
- (53613329)
7.9 x 66.7mm
21pc. WL5 - Wafer Lag
1/4 x 2-1/2"
- (52613222)
6.4 x 63.5mm
8pc. WL3 - Wafer Lag
1/4 x 1-3/8"
- (52613216)
6.4 x 34.9mm
20pc. FW3 - #8 Flat Washer
- (51003500)
20pc. S5 - Pan Screw
#8 x 1/2"
- (52433502)
6.4mm
7.9mm
4.8mm
25.4mm
50.8mm
Hardware Identification (Actual Size)

14
1x - Cozy Escape Playhouse Rocks
(7 Pk) (3329045)
3x - Flat Panel
Brkt
(9201633)
1x - Cozy Escape Bracket Set
(3209045)
- TNR 2 Slide Elbow
1x - TNR 2 Slide
Exit Top
1x
(9200015)
1x
Stake (6 Pk)
(3200318)
1x
Robertson Driver
(9200014)
1x (9207713)
Door Catch
2x (9207711)
Door Handle
1x Magnetic Catch
1x Catch Plate
1x - Magnetic Catch Kit (3201730)
1x
1x - TNR3 Extend Flange Rt
1x - TNR3 Short Exit
1x - TNR 3 Tube Support
(9201601)
10x - TNR 4 Clamp Ring
10pcs number 3300130
1x - TNR4 Post Mount Kit (3201655)
1x
(9300183)
31x - Square
Nylok Nut
(54902200)
2x - TNR 4 Post
Mount Clamp
(9201657)
1x - TNR 4
Post Mount
Base
(9201656)
1x - 1/4 x
14.5mm
Pan Head
Bolt
(53452209)
30x - 1/4 x
12.7mm Pan
Head Bolt
(53453202)
1x - Factory Mount
Door Hinge (2 Pk)
(3200147)
1x - Pot Pan Spatula
(9320889)
1x - Utensils Shelf
(9320791)
1x - Deluxe Kitchen Set - (3320969)
1x - Sink Set
(3330908)
1x - Faucet (9320881)
1x - Sink Knob (9320482)
1x - Sink Knob (9320382)
1x - Sink (9330908)
1x - Stove
(3320738)
2x
- Flower Box Set
(9202111) (Peacock)
1x - Door Bumper
(9331632)
1x - Cozy Escape Triangle Canopy Set
1x - Special Weather
Caps (3322857)
(22 Pk of 9332857)
Cozy Escape Wave ASA Roof Panel Set
1x - 1124mmX1067mm PVC Roof Panel (9332853)
1x - 370mmX1067mm PVC Roof Panel (9332854)
1x - 1064mmX650mm PVC Roof Panel (9332855)
1x - 430mmX650mm PVC Roof Panel (9332856)
1x
1x - Kidkraft
(9320374)
8x - Mount Clips
(9320088)
10x -
#6 x 10mm Blunt
Point Pan Screw
(52402902)
(Reduced Part Size)
- Cozy Escape Wave ASA Roof Panel Set (Dark Grey)

15
B. If there are any missing or damaged pieces or you need assistance with
assembly please contact the consumer relations department directly. Call us
before going back to the store.
Quantity Key Number Part Description,
Part Size
2X 012 Post 2 x 4 x 83”
Step 1: Inventory Parts - Read This Before Starting Assembly
C. Read the assembly manual completely, paying special attention to ANSI warnings;
notes; and safety/maintenance information on pages 1 - 6.
D. Before you discard your cartons ll out the form below.
• The carton I.D. stamp is located on the end of each carton. The tracking number is
located on the KidKraft ID Plaque (9320374).
• Please retain this information for future reference. You will need this information if you
contact the Consumer Relations Department.
• Please refer to Page 6 for proper hardware assembly.
• Each step indicates which bolts and/or screws you will need for assembly, as well as
any at washers, lock washers, t-nuts or lock nuts.
A. This is the time for you to inventory all your hardware, wood and accessories,
referencing the parts identication sheets. This will assist you with your assembly.
• The wood pieces will have the key number stamped on the ends of the boards.
Organize the wood pieces by step, as per the key numbering system below.
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 4)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 5)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 6)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 1)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 2)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 3)
MODEL NUMBER: F29045
TRACKING NUMBER (from ID Plaque):
[phone]
[email protected]
For online parts replacement visit
https://parts.kidkraft.eu/
1.800.933.0771 or 972.385.0100
[email protected]
[email protected]
For online parts replacement visit
https://parts.kidkraft.com/

16
Wood Parts
Fig. 2.1
Hardware
10 x 1/4 x 2-1/2” Wafer Lag
WL5
WL5
WL5
9263
9265
Step 2: Frame Assembly
Part 1
1 x Folding Panel Assembly Right A 2-1/2 x 22 x 90”
1 x Folding Panel Assembly Left B 2-1/2 x 34-1/4 x 90”
9263
9265
A: With a helper, stand the (9263) Folding Panel Assembly Right A in the upright position and unfold, checking to
make sure the panel assembly is square. Pre-drill using a 3/16” drill bit, then install 5 (WL5) 1/4 x 2- 1/2” Wafer
Lags to secure the panel. (g 2.1)
B: Repeat step A to secure the (9265) Folding Panel Assembly Left B. (g 2.1)

17
Hardware
Step 2: Frame Assembly
Part 2
Fig. 2.2
WL5
WL5
9266
9264
Wood Parts
1 x Folding Panel Assembly Left A 2-1/2 x 22 x 90”
1 x Folding Panel Assembly Right B 2-1/2 x 34-1/4 x 90”
9264
9266
10 x 1/4 x 2-1/2” Wafer Lag
WL5
C: With a helper, stand the (9264) Folding Panel Assembly Left A in the upright position and unfold, checking to
make sure the panel assembly is square. Pre-drill using a 3/16” drill bit, then install 5 (WL5) 1/4 x 2- 1/2” Wafer
Lags to secure the panel. (g 2.2)
D: Repeat step C to secure the (9266) Folding Panel Assembly Right B. (g 2.2)

18
2 x Side Joist 1-1/2 x 1-1/2 x 53-3/8”
Wood Parts
9462
Hardware
Fig. 3.1
Fig. 3.2
9462
9266
9266 9263
9265
9264
9265
9462
Step 3: Join Frame Assemblies
Part 1
9462
Panel
5/8” (16mm)
5/16” Flat
Washer
TightTight 5/16” Flat
Washer
x 3 per
joist
x 3 per joist
5/16”
T-Nut
5/16”
T-Nut
5/16”
T-Nut
WB10
Fig. 3.3
S3
S3 S3
S3
NOTE hole orientation
Top View
WB10
WB10
4 x #8 x 2-1/2” Wood Screw
6 x 5/16 x 2-5/8” Wafer Bolt
(5/16” at washer, 5/16” t-nut)
S3
WB10
A: From inside the assembly, halfway up and tight to both end walls, place 1 (9462) Side Joist against (9265)
Folding Panel Assembly Left B and (9264) Folding Panel Assembly Left A, making sure that it’s 5/8” below the
panel opening. Loosely attach (9462) Side Joist with 3 (WB10) 5/16 x 2-5/8” Wafer Bolts (with at washer and
t-nut). Bolts are installed from inside the assembly. Make sure (9462) Side Joist is level then attach with 2 (S3) #8
x 2-1/2” Wood Screws and tighten bolts. (g. 3.1 & 3.2 & 3.3)
B: Repeat Step A to attach 1 (9462) Side Joist to (9263) Folding Panel Assembly Right A and (9266) Folding Panel
Assembly Right B. (g. 3.1 & 3.2 & 3.3)
9263

19
2 x Floor Joist 1-1/4 x 2-1/2 x 53-3/8”
2 x Floor Joist Short 1-1/4 x 2-1/2 x 31-3/8”
Wood Parts
9460
9461
Hardware
Fig. 3.4
Step 3: Join Frame Assemblies
Part 2
Fig. 3.7 Fig. 3.8
9461
S7
S7
9460
x 8
x 8
Fig. 3.5
Fig. 3.6
9460
9461
16 x #12 x 2” Pan Screw
S7
C: Place 1 (9460) Floor Joist along the bottom of the front and back walls so they are ush to the bottom. Check
to make sure that the joists are level then attach each joist using 4 (S7) #12 x 2” Pan Screws. (g.3.4, 3.5 and 3.7)
D: Place 1 (9461) Floor Joist Short along each end wall, between the (9460) Floor Joists. Check to make sure
they are level and ush to the bottom, then attach using 4 (S7) #12 x 2” Pan Screws per side. (g. 3.4, 3.6 and
3.8)
Flush
Flush
Bottom View Bottom View

20
Fig. 3.9
S7
9460
x 8
2 x Floor Joist 1-1/4 x 2-1/2 x 53-3/8”
2 x Floor Joist Short 1-1/4 x 2-1/2 x 31-3/8”
Wood Parts
9460
9461
Step 3: Join Frame Assemblies
Part 3
9461
9461
9460
Hardware
18 x #12 x 2” Pan Screw
S7
Fig. 3.10 Fig. 3.11
E: Place 1 (9460) Floor Joist along the top of the front and back walls so they are ush to the top. Check to
make sure that the joists are level then attach each joist using 5 (S7) #12 x 2” Pan Screws. (g.3.9 and 3.10)
F: Place 1 (9461) Floor Joist Short along the top of each end wall, between the (9460) Floor Joists. Check to
make sure they are level and ush to the top, then attach using 4 (S7) #12 x 2” Pan Screws per side. (g. 3.9
and 3.11)
Top View
9461
S7 x 8
Note hole orientation