KidKraft Cedar Summit Canyon Ridge User manual

INSTALLATION AND OPERATING INSTRUCTIONS
CANYON RIDGE – F25715
Rev 12/14/20179405715
Table of Contents
Warnings and Safe Play Instructions..........pg. 2
Protective Surfacing Guidelines. . . . . . . . . . . . . . . pg. 3
Instructions for Proper Maintenance .........pg. 4
About Our Wood – Limited Warranty.........pg. 5
Keys to Assembly Success ....................pg. 6
Part ID .......................................pg. 8
Step-By-Step Instructions ...................pg. 19
Installation of I.D./Warning Plaque......Final Step
To reduce the risk of serious injury or death, you must read and
follow these instrucons. Keep and refer to these instrucons
oen and give them to any future owner of this play set.
Manufacturer contact informaon provided below.
OBSTACLE FREE SAFETY ZONE -30’ 9” x 27’1” (9.37 x 8.23 m) area requires Protecve Surfacing. See page 3.
MAXIMUM VERTICAL FALL HEIGHT - 6’ 7” (2.01 m)
CAPACITY - 12 Users Maximum, Ages 3 to 10; Weight Limit 110 lbs. (49.9 kg) per child.
RESIDENTIAL HOME USE ONLY. Not intended for public areas such as mul-unit residences, schools, churches,
nurseries, day cares or parks.
WARNING
30'-9"
18'-9"
27' -1"
11'-10"
CANYONRIDGEh:11FT
2-4 Hrs
10 - 12 Hrs
FOR FORT & SWING
TWO PERSON
ASSEMBLY
10 - 12 Hrs
FOR FORT & SWING
2 - 4 Hrs
TUBE SLIDE
10 - 12 Hrs
FOR FORT & SWING
TWO PERSON
ASSEMBLY
Cedar Summit by KidKraft
4630 Olin Road
Dallas, TX 75244, United States
customersupport@kidkraft
Online Parts Replacement:
Cedarsummitplay.com/parts-center-warranty-claim
Customer Service:
1(800) 933-0771 or [phone]
KidKraft Netherlands BV
Olympisch Stadion 29
1076DE Amsterdam, The Netherlands
Europe Customer Service: [phone]
[e-mail]
EU Online Parts Replacement: parts.kidkraft.eu

Warnings and Safe Play Instructions
CONTINUOUS ADULT SUPERVISION REQUIRED. Most serious injuries and deaths on playground equipment have occurred
while children were unsupervised! Our products are designed to meet mandatory and voluntary safety standards. Complying
with all warnings and recommendations in these instructions will reduce the risk of serious or fatal injury to children using
this play system. Go over the warnings and safe play instructions regularly with your children and make certain that they
understand and follow them. Remember on-site adult supervision is required for children of all ages.
Observe capacity limitations of your play-set. See
front cover.
Dress children with well fitting and full foot enclosing
footwear.
Teach children to sit with their full weight in the center
of the swing seat to prevent erratic swing motion or
falling off.
Check for splintered, broken or cracked wood; missing,
loose, or sharp edged hardware. Replace, tighten and or
sand smooth as required prior to playing.
Verify that suspended climbing ropes, rope ladders, chain
or cable are secured at both ends and cannot be looped
back on itself as to create an entanglement hazard.
On sunny and or hot days, check the slide and other
plastic rides to assure that they are not very hot as to
cause burns. Cool hot slide and rides with water and wipe
dry prior to using.
Do not allow children to wear open toe or heel footwear
like sandals, flip–flops or clogs.
Do not allow children to walk, in front, between, behind
or close to moving rides.
Do not let children twist swing chains or ropes or loop
them over the top support bar. This may reduce the
strength of the chain or rope and cause premature failure.
Do not let children get off rides while they are in motion.
Do not permit climbing on equipment when it is wet.
Do not permit rough play or use of equipment in a
manner for which it was not intended. Standing on or
jumping from the roof, elevated platforms, swings,
climbers, ladders or slide can be dangerous.
Do not allow children to swing empty rides or seats.
Do not allow children to go down slide head first or
run up slide.
2
SERIOUS HEAD INJURY HAZARD
Installation over concrete, asphalt, dirt, grass, carpet
and other hard surface creates a risk of serious injury
or death from falls to the ground. Install and maintain
shock absorbing material under and around play-set as
recommended on page 3 of these instructions.
COLLISION HAZARD
Place play-set on level ground at least 6 feet from any
obstruction such as a garage or house, fences, poles,
trees, sidewalks, walls, landscape timbers, rocks,
pavement, planters, garden borders, overhanging
branches, laundry lines, and electrical wires. (See
OBSTACLE FREE SAFETY ZONE on cover)
CHOKING HAZARD/SHARP EDGES & POINTS
Adult assembly required. This product contains small
parts and parts with sharp edges and points. Keep parts
away from children until fully assembled.
WARNING LABEL
Owners shall be responsible for maintaining the legibility
of the warning labels.
STRANGULATION HAZARD
• NEVER allow children to play with ropes, clotheslines,
pet leashes, cables, chains or cord-like items when using
this play-set or to attach these items to play-set.
• NEVER allow children to wear loose tting clothing,
ponchos, hoods, scarves, capes, necklaces, items with
draw-strings, cords or ties when using this play-set.
• NEVER allow children to wear bike or sport helmets
when using this play-set.
Failure to prohibit these items, even helmets with chin
straps, increases the risk of serious injury and death to
children from entanglement and strangulation.
TIP OVER HAZARD
Choose a level location for the equipment. This can reduce
the likelihood of the play set tipping over and loose-fill
surfacing materials washing away during heavy rains.
DO NOT allow children to play on the play-set until the
assembly is complete and the unit is properly anchored.
WARNING
WARNING – Safe Play Instructions
2

One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing
protective surfacing under and around your play equipment. The protective surfacing should be applied to a depth that is suitable
for the equipment height in accordance with ASTM F1292. There are different types of surfacing to choose from; whichever
product you select, follow these guidelines:
Loose-Fill Materials
• Maintain a minimum depth of 9 inches of loose-fill materials such as wood mulch/chips, engineered wood fiber (EWF), or
shredded/recycled rubber mulch for equipment up to 8 feet high; and 9 inches of sand or pea gravel for equipment up to 5 feet
high. NOTE: An initial fill level of 12 inches will compress to about a 9-inch depth of surfacing over time. The surfacing will also
compact, displace, and settle, and should be periodically raked and refilled to maintain at least a 9-inch depth.
• Use a minimum of 6 inches of protective surfacing for play equipment less than 4 feet in height. If maintained properly, this
should be adequate. (At depths less than 6 inches, the protective material is too easily displaced or compacted.)
NOTE: Do not install home playground equipment over concrete, asphalt, or any other hard surface. A fall onto a hard surface
can result in serious injury to the equipment user. Grass and dirt are not considered protective surfacing because wear and
environmental factors can reduce their shock absorbing effectiveness. Carpeting and thin mats are not adequate protective
surfacing. Ground level equipment -- such as a sandbox, activity wall, playhouse or other equipment that has no elevated play
surface -- does not need any protective surfacing.
• Use containment, such as digging out around the perimeter and/or lining the perimeter with landscape edging. Don’t forget to
account for water drainage.
• Periodically rake, check and maintain the depth of the loose-fill surfacing material. Marking the correct depth on the play
equipment support posts will help you to see when the material has settled and needs to be raked and or replenished. Be sure to
rake and evenly redistribute the surfacing in heavily used areas.
• Do not install loose fill surfacing over hard surfaces such as concrete or asphalt.
Poured-In-Place Surfaces or Pre-Manufactured Rubber Tiles
You may be interested in using surfacing other than loose-fill materials - like rubber tiles or poured-in-place surfaces.
• Installations of these surfaces generally require a professional and are not “do-it yourself ” projects.
• Review surface specifications before purchasing this type of surfacing. Ask the installer/manufacturer for a report showing that
the product has been tested to the following safety standard: ASTM F1292 Standard Specification for Impact Attenuation of Surfacing
Materials within the Use Zone of Playground Equipment. This report should show the specific height for which the surface is intended
to protect against serious head injury. This height should be equal to or greater than the fall height - vertical distance between a
designated play surface (elevated surface for standing, sitting, or climbing) and the protective surfacing below - of your play equipment.
• Check the protective surfacing frequently for wear.
Placement
Proper placement and maintenance of protective surfacing is essential. Refer to diagram on front cover. Be sure to;
• Extend surfacing at least 6 feet from the equipment in all directions.
• For to-fro swings, extend protective surfacing in front of and behind the swing to a distance equal to twice the height of the top
bar from which the swing is suspended.
• For tire swings, extend surfacing in a circle whose radius is equal to the height of the suspending chain or rope, plus 6 feet in all directions.
Protective Surfacing - Reducing Risk of Serious Head Injury From Falls
From the CPSC Outdoor Home Playground Safety Handbook. At http://www.playgroundregs.com/resources/CPSC%20324.pdf
Denotes Use Zone with Protective Surfacing
Denotes Use Zone with Protective Surfacing
6 ft.
6 ft. 6 ft.
6 ft.
6 ft. 6 ft.
6 ft.
Use Zone for Multi-Axis SwingsUse Zone for Single-Axis Swings
3

Instructions for Proper Maintenance
Your Cedar Summit Play System is designed and constructed of quality materials with your child’s safety in mind. As
with all outdoor products used by children, it will weather and wear. To maximize the enjoyment, safety and life of your
Play Set, it is important that you, the owner, properly maintain it.
HARDWARE:
Check metal parts for rust. If found,
sand and repaint using a non-lead paint
complying with 16 CFR 1303.
Inspect and tighten all hardware. On
wood assemblies DO NOT OVER-
TIGHTEN as to cause crushing and
splintering of wood.
Check for sharp edges or protruding screw threads, add
washers if required.
SHOCK ABSORBING SURFACING:
Check for foreign objects. Rake and check depth of loose
fill protective surfacing materials to prevent compaction and
maintain appropriate depth. Replace as necessary.
(See Protective Surfacing, page 3)
GROUND STAKES (ANCHORS):
Check for looseness, damage or deterioration. Should firmly
anchor unit to ground during use. Re-secure and or replace,
if necessary.
SWING HANGERS:
Check that bolts are secure and tight. Quick clips should be
completely closed and threaded clips screwed tight.
If squeaking occurs lubricate bushings with oil or WD-40®.
SWINGS, ROPES AND RIDES:
Reinstall if removed during cold season. Check all moving
parts including swing seats, ropes, chains and attachments
for wear, rust and other deterioration. Replace as needed.
Check that ropes are tight, secure at both ends and cannot
loop back as to create an entrapment.
WOOD PARTS:
Check all wood members for deterioration, structural
damage and splintering. Sand down splinters and replace
deteriorated wood members. As with all wood, some
checking and small cracks in grain is normal.
Applying a water repellent or stain (water-based) on a yearly
basis is important maintenance to maintain maximum life
and performance of the product.
Check the following at the beginning of the play season:
HARDWARE:
Inspect for tightness. Must be firmly against, but not
crushing the wood. DO NOT OVER-TIGHTEN.
This will cause splintering of wood.
Check for sharp edges or protruding screw threads.
Add washers if required.
SHOCK ABSORBING SURFACING:
Rake and check depth of loose fill protective surfacing
materials to prevent compaction and maintain appropriate
depth. Replace as necessary.
(See Protective Surfacing, page 3)
Check twice a month during play season:
SWING HANGERS:
Check that they are secure and orientated correctly. Hook
should rotate freely and perpendicular to support beam.
If squeaking occurs lubricate bushings with oil or WD-40®.
SWINGS AND RIDES:
Check swing seats, all ropes, chains and attachments for
fraying, wear, excessive corrosion or damage.
Replace if structurally damaged or deteriorated.
Check once a month during play season:
SWINGS AND RIDES:
To prolong their life, remove swings and store inside when
outside temperature is below 32°F/0°C. Below freezing,
plastic parts may become more brittle.
SHOCK ABSORBING SURFACING:
Rake and check depth of loose fill protective surfacing
materials to prevent compaction and maintain appropriate
depth. Replace as necessary.
(See Protective Surfacing, page 3)
Check at the end of the play season:
If you dispose of your play set: Please disassemble and dispose of your unit so that it does not create any unreasonable
hazards at the time it is discarded. Be sure to follow your local waste ordinances.
If Bolt protrudes
beyond T-Nut
Use an extra
flat washer
4

AboutOur Wood
Cedar Summit Premium Play Systems uses only premiumplayset lumber, ensuringthesafest product for your children’s
use. Although we take great care in selectingthebest quality lumber available, wood is still aproduct ofnature and susceptibleto
weatheringwhich can change the appearance of your set.
What causes weathering? Does itaffect the strength of my Play System?
Oneofthe main reasons for weatheringis the effects of water (moisture); the moisture content ofthe wood at thesurface is
different than theinterior ofthe wood. As the climate changes, moisture moves in or out ofthe wood, causingtension which can
result in checking and or warping. You can expect thefollowingdueto weathering. These changes will not affect thestrength of
theproduct:
1. Checking is surface cracks in the wood alongthe grain. A post (4” x 4”)will experience more checkingthan aboard (1” x 4”)
becausethesurface and interior moisture content will vary morewidely than in thinner wood.
2. Warping results from any distortion (twisting, cupping) fromtheoriginal plane oftheboard and often happens fromrapid
wetting and dryingofthe wood.
3. Fading happens as anatural change in the wood color as it is exposed to sun-light and will turn a grey over time.
How can I reduce the amount of weathering to my Play System?
At thefactory we have coated the wood with a water repellent or stain. This coatingdecreases the amount of water absorption
during rain orsnow thus decreasingthetension in the wood. Sunlight will break down the coating, applying a water repellant or
stain on a yearly basis is important maintenance. (see your local stain and paint supplier for arecommended product)
Most weathering is just the normal result of nature and will not affect safe play and enjoyment for your child. However if you are
concerned that a part has experienced a severe weathering problem please call our consumer relations department for further assistance.
warranty service.
province to province. This warranty excludes all consequential damages, however, some states do not allow the
limitation or exclusion of consequential damages, and therefore this limitation may not apply toyou.
10 Year Limited Warranty
Cedar Summit by KidKra warrants that this product is free fromdefect in materials and workmanship
for a periodof one year from the original date of purchase. In addition, lumber is warranted for 10
years against structural failure due to rot and insect damage. All other parts, such as hardware, swings,
rides, accessories, and slides carry aone-year warranty only.
This warranty appliesto the original owner and registrant and is non-transferable.
Regular maintenance is required to assure the integrity of your Play System. Failureby the owner
to maintain the product accordingto the maintenance requirements may void this warranty. This
warranty does not cover any inspectioncost.
This Limited Warranty does not cover:
•Labour for replacement of any defective item(s);
•Incidental or consequential damages;
• Cosmetic defects which do not affect performance or integrity;
• Vandalism; improper useor installation; acts of nature;
• Minor twisting, warping, checking, or any other natural occurring properties of wood that do not
affect performance or integrity.
Cedar Summit by KidKraft products have been designed for safety and quality. Any modifications
made to the original product could damage the structural integrity of the unit leading to failureand
possible injury. Cedar Summit by KidKraft cannot assume any responsibility for modified products.
Furthermore, modification voids any and all warranties.
This product is warranted for RESIDENTIAL USE ONLY. Under no circumstance should a Cedar Summit
by KidKra Play System beused in public settings such as schools, churches, playgrounds, parks, day cares
and the like. Such use may lead to product failure and potential injury. Any and all public usewill void this
warranty.
Cedar Summit by KidKraft disclaims all other representations and warranties of any kind, express or implied.
5

This identifies information that requires special
attention. Improper assembly could lead to an unsafe
or dangerous condition.
Where this is shown, 2 or 3 people
are required to safely complete the
step. To avoid injury or damage
to the assembly make sure to get
help!
Check that assembly is square
before tightening bolts.
Use a measuring tape to assure
proper location.
Check that set or assembly is properly level
before proceeding.
Pre-drill a pilot hole
before fastening screw
or lag to prevent
splitting of wood.
This indicates time to tighten bolts, but
not too tight! Do not crush the wood.
This may create splinters and cause
structural damage.
Part Identification Key
On each page, you will find the parts
and quantities required to complete the
assembly step illustrated on that page.
Here is a sample.
Key Number: The first two digits
represent the step number. The third
digit represents the piece. Note that if
the part is used in multiple steps then
the number only reflects the first step it
is used in.
Symbols
Throughout these instructions symbols are provided as important reminders for proper and safe assembly.
Proper Hardware Assembly
Lag screws require drilling pilot
holes to avoid splitting wood. Only
a flat washer is required. For ease of
installation liquid soap can be used
on all lag-type screws.
For bolts, tap T-Nut into hole with
hammer. Insert the hex bolt through
lock washer first then flat washer then
hole. Because the assemblies need to
be squared do not completely tighten
until instructed. Pay close attention to
diameter of the bolts. 5/16” is slightly
larger than 1/4”.
Note: Wafer head bolts with blue lock
tight or a bolt with a Ny-Lok nut do
NOT require a lock washer.
Once the assembly is tightened, watch for exposed threads.
If a thread protrudes from the T-Nut, remove
the bolt and add washers to eliminate this condition.
Extra washers have been provided for this purpose.
Use
Help
Use
Help
Measure
Distance
Square
Assembly
Use
Level
Pre-drill 1/8” & 3/16” Bit
Tighten
Bolts
CAUTION – Protrusion Hazard
Keys to Assembly Success
Tools Required
• Tape Measure
• Carpenters Level
• Carpenters Square
• Claw Hammer
• Standard or Cordless Drill
• #1, #3 Phillips or Robertson
bit or Screwdriver
• Ratchet(1/2”, 7/16” &
9/16” sockets)
• Open End Wrench
(1/2”, 7/16” & 9/16”)
• Adjustable Wrench
• 1/8” & 3/16” Drill Bits
• 3/16” Hex Key
• 8’ Step Ladder
• Safety Glasses
• Adult Helpers
• Pencil
Quantity Key Number Part Description,
Part Size
2X 012 Post 2 x 4 x 83”
No Yes
Lag Assembly
Bolt Assembly
Flat Washer
Lag Screw
Hex Bolt
Lock
Washer
Flat
Washer
Before mounting Lag
Screw, use factory drilled
holes as guides to drill 1/8”
pilot holes
T-Nut
(Hammer into place)
Do not crush wood!
If Bolt protrudes
beyond T-Nut
Use an extra
flat washer
6

Key Number: The rst two digits represent the step
number. The third digit represents the order in which
the part is listed in the step.
Note that if the part is used in multiple steps then
the key number only reects the rst step it is used in.
Part Quantity Key Number
Order Listed
(The order the part is
listed in step 1)
Part Description Part Size
2X 012 Post 2 x 4 x 83”
Your Key To Quick Assembly
SAVE TIME - TIP #1:
Open each box with wood parts and look for the Key Number
stamped on the end of the wood part (see chart below). Sort
each wood part into the different assembly steps.
SAVE TIME - TIP #2:
In addition to the key number stamp, you can also identify
the wood parts by using the Parts Identication pages in the
manual or the Parts Identication weather resistant poster.
HARDWARE:
The majority of each hardware part comes packed in a separate
bag so you do not need to sort the hardware. Each assembly step
indicates which hardware (bolt, screw, washer etc.) you will
require to complete the step.
SORTING WOOD PARTS INTO
EACH ASSEMBLY STEP WILL
SAVE TIME!
Step Step Step
01 2
Step Number
(This is Step 1)
7

10X TNR 2 Slide Clamp Ring
081
Back Roof Panel FSC
400
351
491
Plaque
Rebar Ground Stake x6
Door Window
Front Roof Panel FSC350
Door Hardware
Sign
with Mount
Telescope
120
Slide End Panel FSC
Steering Wheel
TNR3 Short Exit
TNR 2 Slide Exit Top
9X TNR 2 Slide Elbow
TNR 2 Slide RT Flange
404
Panel FSC
TNR 2 Slide LT Flange
140
TNR3 Post Mount
MOD 5 Pane Window x4
Cedar Summit
040 Narrow Front Panel FSC 042
130 131
FRONT
210
222
202
190
190
200
1X Maze N Wave Slide
Sink
BBQ Base
Fruit +
Basket
460460
450
Cooktop133
2X
480
341
2X
MOD 3 pane Gable x4
410
403
402
401
490
062
371
092
340
090
Flags
DX Flying
091
280
281
480
093
2X
134
Utensil Shelf
390
Panel FSC
Front Wall
370
Bracket 4x Flat
051
2X
380
X2 136
134
135
211
200
202
191
x2
230
204
220
221x2
192
204
203
x4
210
222
201
8

2X Swing Belt Seat
5X Narrow Angle Bracket (2pk)
391 Front Small Roof FSC
141
SW Wall Panel FSC
X2
6X PanelCorner Brackets
Hanger
x17
1X Acro
Washer
030
031
032
033
100
033
033
033
032
032
050
Bar
Handle
1X
420
032
6X -DX Swing
4X 48" Chain
2X Acro
Chain
023
Heavy "C" Bracket
2X 20"
Plastic Formed
281
2X
Heavy "L" Bracket X3
160
Heavy Flat Bracket x2
151 150
280
072
13x 070
071
025
4x230
033
024
080
210
2X 411
Bracket x4
222
Flat Panel
1X Flat
Support
021
Grip x2
Bracket (2pk)
TNR3 Tube
I.D Plaque
201
152
204
1X Rocks (9pk)
Steel Hand
2X
121
052
Back Wall Panel FSC
041
4X022
2X
061
Narrow Back PanelFSC
BACK
060
131
192
020
392 Back Small RoofFSC
Threaded
6X Quick links
9

(1) 023 - 1 x 4 x 21" - Ladder Gap FSC - Box 2 - 4598958
Part Identification (Reduced Size)
(1) 072 - 1 x 4 x 35-5/8" - Floor Board FSC - Box 3 - 4599050
(1) 025 - 1 x 4 x 41-3/4" - RW - AL Support FSC - Box 2 - 4599062
(4) 230 - 1 x 4 x 29" - Cedar Wall FSC - Box 3 - 4591975
(1) 031 - 1 x 5 x 22-1/8" - Access Board FSC - Box 2 - 4599032
(13) 070 - 1 x 5 x 35-5/8" - Floor Board FSC - Box 2,3 - 4599051
(2) 221 - 1 x 6 x 29-3/8" - Crowsnest Floor FSC - Box 2 - 4599038
(1) 220 - 1 x 6 x 29-3/8" - Crowsnest Gap Board FSC - Box 2 - 4599040
(5) 033 - 1 x 6 x 22-1/8" - Board Rock B FSC - Box 2 - 4598512
(1) 030 - 1 x 6 x 22-1/8" - Access Rock Bottom FSC - Box 3 - 4598515
(4) 032 - 1 x 6 x 22-1/8" - Board Rock A FSC - Box 2 - 4598511
(1) 135 - Bell Top RT 5/8 x 3-3/8 x 11-1/4" FSC - Box 2
4609101
(1) 134 - Bell Top 5/8 x 3-3/8 x 11-1/4" FSC - Box 2 - 4609102
(2) 491 - 1 x 5 x 10" Transom Board B FSC - Box 2 4599116
(2) 490 - 1 x 5 x 14-1/2" Transom Board A FSC Box 2 - 4599115
10

(2) 390 - Mid Roof Support 1¼ x 2¼ x 32-3/4" FSC - Box 3 - 4599109
(2) 341 - Roof Support Small 1¼ x 2¼ x 29-11/16" FSC - Box 3 - 4599104
Part Identification (Reduced Size)
(4) 340 - Roof Support 1¼ x 2¼ x 33" FSC - Box 2 - 4599105
(1) 080 - 5/4 x 3 x 33-1/2" - SW Wall Top FSC - Box 3 - 4599071
(1) 081 - 5/4 x 3 x 33" - Half Wall Top FSC - Box 3 - 4599053
(1) 090 - 5/4 x 4 x 14¼ - SW Ground FSC - Box 3 - 4592606
(1) 121 - 5/4 x 3 x 10" - Door Stop FSC - Box 2 - 4592715
(2) 201 - 1 x 2 x 34-1/8" - Upright Crowsnest FSC - Box 3 - 4599072
(4) 022 - 5/4 x 4 x 19-1/2" - Tread FSC - Box 3 - 4598957
(1) 100 - 5/4 x 4 x 27-3/4" - RW-AL Ground Brace FSC - Box 3 - 4599061
(1) 203 - 5/4 x 4 x 25-1/2" - Crowsnest Short FSC - Box 3 - 4598115
(1) 131 - 5/4 x 5 x 39-5/8" - Table Top FSC - Box 3 - 4592611
(2) 212 - 3/4 x 3-1/4 x 14-3/4" - Crowsnest Side FSC - Box 2 - 4599042
(2) 204 - 1-1/4 x 2 x 27-1/2" - Crowsnest Spacer FSC - Box 2 - 4599043
(2) 210 - 3/4 x 5-1/4 x 14-3/4" - Crowsnest Bottom Side FSC - Box 3- 4599037
(2) 404 - 15/16 x 3 x 19-1/4" - Wall Tie FSC - Box 3
4599117
(2) 062 - Tie 1 x 3 x 24-1/2" FSC - Box 3 - 4599123
11

(1) 280 - 1-1/4 x 3 x 32-1/4" - TNR Ground Brace FSC - Box 2 - 4598963
Part Identification (Reduced Size)
(1) 024 - 1-3/8 x 2-1/2 x 57-7/8" - Rock Rail FSC - Box 1 - 4599058
(2) 060 - 1-1/4 x 3 x 40-3/4" - Floor Joist FSC - Box 3 - 4592608
(1) 071 - 1-1/4 x 3 x 63-1/4" - Long Floor Joist FSC - Box 3 - 4599056
(1) 021 - 1-3/8 x 2-1/2 x 57-7/8" - Right Access FSC - Box 1 - 4599055
(1) 281 - 1-1/4 x 3 x 20-1/4" - TNR Upright FSC - Box 3 - 4598965
(1) 020 - 1-3/8 x 2-1/2 x 57-7/8" - Left Access FSC - Box 1 - 4599054
(1) 091 - 1-1/4 x 3 x 22" - Diagonal FSC - Box 2 - 4592607
(1) 192 - 5/4 x 4 x 34" - Crowsnest Back FSC - Box 2 - 4599036
(2) 411 - Swing Side Upright 1-1/4 x 2-1/2 x 16-1/2" FSC - Box 3 - 4599112
(2) 400 - TB Support 1¼ x 2½ x 44¼" FSC - Box 3 - 4599114
(2) 460 - Roof End Short 1¼ x 3 x 6" FSC - Box 2 - 4599103
(1) 092 - 5/4 x 4 x 24½" - Support Diagonal FSC - Box 2 - 4599111
(1) 380 - Dormer Cleat 1¼ x 3 x 10" FSC - Box 3 - 4599122
(1) 410 - Swing Top 1¼ x 3 x 46-3/4" FSC - Box 3 - 4599113
(2) 480 - Long Roof End 1¼ x 3 x 16-3/8" FSC - Box 3 - 4599108
(2) 403 - Centre Upright 1¼ x 3 x 16½" FSC - Box 3 - 4599106
(2) 401 - Right Upright 1¼ x 3 x 16½" FSC - Box 3 - 4599110
12

(2) 402 - Left Upright 1¼ x 4¼ x 16½" FSC - Box 3 - 4599107
(2) 450 - Mid Roof End 1¼ x 4 x 6" FSC - Box 3 - 4599119
(1) 202 - 2 x 4 x 29-1/2" - Crowsnest Front FSC - Box 3 - 4599039
(1) 093 - 2 x 3 x 42¼" - Diagonal FSC - Box 3 - 4598587
(2) 420 - Wall Support 1½ x 1½ x 55½" FSC - Box 3 - 4599118
(1) 200 - 2 x 4 x 29-1/2" - Crowsnest Top FSC - Box 3 - 4599044
Part Identification (Reduced Size)
(1) 130 - 2 x 2 x 39-5/8" - Table Support FSC - Box 1 - 4592612
(2) 211 - 2 x 4 x 12-1/2" - Short Crowsnest Joist FSC - Box 2 - 4599063
(2) 061 - 2 x 2 x 63" Side Joist FSC - Box 1 - 4599064
(2) 191 - 2 x 4 x 13-1/2" - Crowsnest Joist FSC - Box 3 - 4599041
(1) 140 - 4 x 6 x 92" - Engineered SW Beam FSC - Box 1 - 4599049
(1) 160 - 2-1/2 x 3 x 51" - Support Cross FSC - Box 1 - 4599067
(2) 152 - 4 x 4 x 92" - SW Post FSC - Box 1 - 4599070
(1) 151 - 2-1/2 x 3 x 15" - Block SW FSC - Box 3 - 4598507
(2) 136 - Bell Support 1½ x 1½ x 10-5/8" FSC - Box 2 - 4609100
(1) 141 - 4 x 4 x 16" - SW Mount FSC - Box 3 - 4599069
(1) 150 - 2-1/2 x 3 x 15" - SW Block Angle FSC - Box 3 - 4599068
(2) 190 - 2 x 6 x 15" Crowsnest Gusset FSC - Box 2 - 4598112
13

(1) 391
Front Small Roof 1¼ x 29 3/16 x 21-7/8"
FSC - Box 3 - 47599098
(1) 350 Front Roof Panel 1¼ x 32½ x 45" FSC
Box 3 - 47599082
(1) 351 Back Roof Panel 1-1/4 x 32¼ x 45" FSC
Box 3 - 47599124
Part Identification (Reduced Size)
(1) 392
Back Small Roof 1-1/4 x 28-15/16 x 21-7/8"
FSC - Box 3 - 47599091
1x - TNR 2 Slide Lt Flange
(3310222) Yellow
1x - TNR 2 Slide Rt Flange
(3310223) Yellow
9x - TNR 2 Slide Elbow
(3310221) Yellow
1x - Dormer Roof Set FSC
370 Right - 371 Left Dormer
(4598068) - Box 3
10x - TNR 2 Slide Clamp Ring
(3300220) Yellow
1x - TNR 2 Slide Exit Top
(3310224) Yellow
1x - TNR3 Short Exit
(3310232) Yellow
14

Part Identification (Reduced Size)
(1) 040 - 1-1/4 x 37 x 92"
Slide End Panel FSC
Box 3 - 47598981
(1) 042 - 1-1/4 x 21-1/2 x 92" - 47599003
Narrow Front Panel FSC - Box 2
(1) 041 - 1-1/4 x 21-1/2 x 92"
Narrow Back Panel FSC - Box 2 - 47598992
(1) 050 - 1-1/4 x 37 x 92"
SW Wall Panel FSC
Box 3 - 47599007
(1) 052 - 1-1/4 x 43 x 92"
Back Wall Panel FSC
Box 2 - 47598970
(1) 120 - 1-1/4 x 15-3/4 x 42-1/8"
Door Window Panel FSC
Box 2 47608977
(1) 051 - 1-1/4 x 43 x 92"
Front Wall Panel FSC
Box 2 - 47599078
15

(2) G5 - Hex Bolt 5/16 x 4-1/2" - (53703342)
(1) H3 - Hex Bolt 1/4 x 2-1/2" - (53703222)
(5) LS9 - Lag Screw 5/16 x 4-3/4" - (52213343)
(1) WB8 - Wafer Bolt 5/16 x 2-3/8" - (53613326)
(7) WB7 - Wafer Bolt 5/16 x 3" - (53613330)
Hardware Identification (Actual Size)
(7) WB10 - Wafer Bolt 5/16 x 2-5/8" - (53613329)
(4) G21 - Hex Bolt 5/16 x 3-3/4" - (53703333)
(12) G13 - Hex Bolt 5/16 x 6-1/8" - (53703364)
(4) G17 - Hex Bolt 3/8 x 6" - (53703860)
(1) G26 - Hex Bolt 3/8 x 9-1/4" - (53703891)
(1) G20 - Hex Bolt 3/8 x 4" - (53703840)
(1) H8 - Hex Bolt 1/4 x 4-1/4" - (53703241)
(4) H10 - Hex Bolt 1/4 x 2-1/4" - (53703221)
(6) H9 - Hex Bolt 1/4 x 1-1/4" - (53703211)
(6) WB9 - Wafer Bolt 5/16 x 2-1/8" - (53613324)
(4) WL3 - Wafer Lag 1/4 x 1-3/8" - (52613216)
(18) WL5 - Wafer Lag 1/4 x 2-1/2" - (52613222)
16

(17) S6 - Pan Screw #12 x 1" - (52433610)
(84) S3 - Wood Screw #8 x 2-1/2" - (52043522)
(22) LW1 - 1/4" Lock Washer - (51303200)
(13) TN1 - 1/4" T - Nut -(54503200)
(27) S7 - Pan Screw #12 x 2" - (52433620)
(26) S4 - Wood Screw #8 x 3" - (52043530)
(187) S20 - Wood Screw #8 x 1-3/8" - (52043516)
(9) S10 - Pan Screw #8 x 1" - (52433510)
(88 ) S0 - Truss Screw #8 x 7/8" - (52933505)
(1) LW2 - 5/16" Lock Washer - (51303300)
Hardware Identification (Actual Size)
(18) FW1 - 1/4" Flat Washer - (51103200)
(1) PB6 - Pan Bolt 1/4 x 1" - (53413210)
(9) FW0 - 3/16" Flat Washer - (51103100)
(40) S8 - Pan Screw #12 x 3/4" - (52433603)
(8) FW6 - #12 Screw Bezel - (9299500)
(89) LN1 - 1/4 Lock Nut - (54303200)
(10) PB2 - Pan Bolt 1/4 x 1-1/4" - (53433212)
(12) FW10 - 3/8" Flat Washer - (51103800)
(6) LN3 - 3/8 Lock Nut - (54303800)
(29) S37 - Pan Screw #7 x 5/8" - (52433009)
(105) S11 - Wood Screw #8 x 2" - (52043520)
(8) S38 - Pan Screw #7 x 1-1/8" - (52433014)
(89) PB1 - Pan Bolt 1/4 x 3/4" - (53453203)
(16) S1 - Wood Screw #8 x 1-1/8" - (52043514)
(64) FW2 - 5/16" Flat Washer - (51103300)
(9) BN1 - 1/4" Barrel Nut - (54803200)
(18) LN2 - 5/16" Lock Nut - (54303300)
(21) TN2 - 5/16" T- Nut - (54503300)
17

2x - MOD 5 Pane Window
(2 Pk) (3330102)
1x - Flat Bracket (2 Pk)
(3205960)
1x - BBQ Sink Set
3330908
1x Magnetic Catch
1x Catch Plate
2x 9201712
Door Hinge -Green
9207713
Door Catch -Brown
2x 9201711
Door Handle -Green
1x - Door Hardware (3201710)
1x - TNR3 Tube Support
(9200258)
1x - TNR3 Post Mount
(9200257)
1x - Heavy C-Bracket
(9200153)
2x - Heavy Flat Bracket
(9200149)
1x - Maze N Wave 2.35m Slide
(3318215) Yellow
1x - BBQ Utensils
3330810
1x - Corner Panel
Bracket (6 Pk)
(3205977)
1x - BBQ Deluxe Kitchen
Set (3330007)
1x - BBQ Base
33308011
1x - BBQ Cooktop 3330909
1x - BBQ Lid
9330718
2x - Utensil Shelf
9320125
1x - Basket with
Fruit 3330013
1x - Sign
9330714
1x
(3330316) (2 Pk)
- Deluxe Flying Flag
1x - Deluxe Pole
(3330328) (2 Pk)
1x - Bell with Horseshoe
(3200307)
1x - MOD 3 Pane Gable
(3330104) (4 Pk)
Part Identification (Reduced Part Size)
1x - KK ID Plaque
(9320357)
1x - Telescope w/ Mount
(3320161)
1x - Rocks (9pk) (3320093)
Green/Yellow/Burgundy
2x - Steel Hand Grip
(9200211) -Yellow
1x - Cedar Summit Plaque
(9320358)
1x - Quadrex Driver
(9200015)
2x - Swing Belt Seat
(9320130) Green
2x - Acro Handle
(9200133) Green
1x - Plastic Formed
Washer (18 Pk)
(3290000)
1x - Acro Bar
(9200131) Green
1x - Steering Wheel
(3320255)
2x - Flat Panel Bracket
(2 Pk)(3205978)
1x - Canyon Ridge Bracket Set
(3205715)
1x - Rebar Ground
Stake (6 Pk)
(3200318)
1x - DX Swing Hangers
with Quick Links (6 Pk)
(3201950)
1x - Corner
Bracket (5 Pk)
(3205979)
3x - Narrow Angle
Bracket (2 Pk)
(3205939)
1x - #2 x 2"
Robertson Driver
(9200014)
3x - Heavy L-Bracket
(9200151)
1x - Heavy Bracket Set
(3205701) Green
- Welded Chain Bag (3200173) Green
1x
4x 48" chain -Green
2x 20" chain -Green
(9320370)
18

STOP STOPSTOP STOP
Key Number: The rst two digits represent the step
number. The third digit represents the piece. Note
that if the part is used in multiple steps then the
number only reects the rst step it is used in.
Quantity Key Number Part Description,
Part Size
2X 012 Post 2 x 4 x 83”
Step 1: Inventory Parts - Read This Before Starting Assembly
• Please refer to Page 6 for proper hardware assembly.
• Each step indicates which bolts and/or screws you will need for assembly, as well as
any at washers, lock washers, t-nuts or lock nuts.
A. This is the time for you to inventory all your hardware, wood and accessories,
referencing the parts identication sheets. This will assist you with your assembly.
• The wood pieces will have the key number stamped on the ends of the boards.
Organize the wood pieces by step, as per the key numbering system below.
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 4)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 5)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 6)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 1)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 2)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 3)
MODEL NUMBER: F25715
TRACKING NUMBER (from ID Plaque):
B. If there are any missing or damaged pieces or you need assistance with
assembly please contact the consumer relations department directly. Call us
before going back to the store.
C. Read the assembly manual completely, paying special attention to ANSI warnings;
notes; and safety/maintenance information.
D. Before you discard your cartons ll out the form below.
• The carton I.D. stamp is located on the end of each carton.
• Please retain this information for future reference. You will need this information if you
contact the Consumer Relations Department.
[email protected]
Online Parts Replacement:
Cedarsummitplay.com/parts-center-
warranty-claim
Customer Service:
1(800) 933-0771 or [phone]
Europe Customer Service: [phone]
[email protected]
EU Online Parts Replacement: parts.kidkraft.eu
19

1 x Left Access 1-3/8 x 2-1/2 x 57-7/8”
1 x Right Access 1-3/8 x 2-1/2 x 57-7/8”
4 x Tread 5/4 x 4 x 19-1/2”
022
021
020
Fig. 2.1
Wood Parts Hardware
Step 2: Access Ladder / Rockwall Assembly
Part 1
A: Place (020) Left Access on one side of 4 (022) Treads and (021) Right Access on the other side with the
grooves facing in. (g. 2.1)
B: Fit each (022) Tread into grooves on both (020) and (021) Access rails, make sure the top edge of the (022)
Treads are ush to the front of the Access rails. (g. 2.1 and 2.2)
C: Pre-drill pilot holes with a 1/8” drill bit and attach rails and treads together using 4 (S3) #8 x 2-1/2” Wood
Screws per tread. (g. 2.1)
16 x #8 x 2-1/2” Wood Screw
S3
Fig. 2.2
020
021
022
End View
Flush to
edges Top Edge of Access Rail
Flush to
top edge
022
S3
S3
20