KidKraft BEAR CAVE LODGE User manual

INSTALLATION AND OPERATING INSTRUCTIONS
BEAR CAVE LODGE PLAYSET– F24872
Table of Contents
Warnings and Safe Play Instructions ...........pg. 2
Protective Surfacing Guidelines................pg. 3
Instructions for Proper Maintenance ...........pg. 4
About Our Wood – Limited Warranty ..........pg. 5
Keys to Assembly Success......................pg. 6
Part ID...................................... pg. 9-24
Step by Step Instruction . . . . . . . . . . . . . . .. pg. 25-147
Installation of I.D./Warning Plaque . . .. . . .Final Step
Rev 06/28/20199404872
KidKraft, Inc.
4630 Olin Road
Dallas, Texas 75244 USA
[email protected]
[email protected]
1.800.933.0771
972.385.0100
For online parts replacement visit
https://parts.kidkraft.com/
KidKraft Netherlands BV
Olympisch Stadion 29
1076DE Amsterdam
The Netherlands
[email protected]
[phone] M-F from 09:00 to 17:30
(GMT+1)
For online parts replacement visit
https://parts.kidkraft.eu/
18-24 Hrs
Two person
assembly
To reduce the risk of serious injury or
death, you must read and follow these
instructions. Keep and refer to these
instructions often and give them to any future owner of this play system. Manufacturer
contact information provided below.
OBSTACLE FREE SAFETY ZONE - 40’10” x 27’10” area requires Protective Surfacing. See
page 3.
MAXIMUM VERTICAL FALL HEIGHT - 6’9”
CAPACITY - 21 Users Maximum, Ages 3to 10; Weight Limit 110 lbs. (49.9 kg) per child.
RESIDENTIAL HOME USE ONLY. Not intended for public areas such as schools, churches,
nurseries, day cares or parks.
Warning. Only for domestic use.
WARNING
11'-4"
40'-10"
27'-10"
27'-9"
Bear Cave Lodge
Safety Zone
Nov 17/2017

2
Warnings and Safe Play Instructions
CONTINUOUS ADULT SUPERVISION REQUIRED. Most serious injuries and deaths on playground equipment have occurred
while children were unsupervised! Our products are designed to meet mandatory and voluntary safety standards. Complying
with all warnings and recommendations in these instructions will reduce the risk of serious or fatal injury to children using
this play system. Go over the warnings and safe play instructions regularly with your children and make certain that they
understand and follow them. Remember on-site adult supervision is required for children of all ages.
SERIOUS HEAD INJURY HAZARD
Installation over concrete, asphalt, dirt, grass, carpet
and other hard surface creates a risk of serious injury
or death from falls to the ground. Install and maintain
shock absorbing material under and around play-set as
recommended on page 3 of these instructions.
COLLISION HAZARD
Place play-set on level ground at least 2m from any
obstruction such as a garage or house, fences, poles,
trees, sidewalks, walls, landscape timbers, rocks,
pavement, planters, garden borders, overhanging
branches, laundry lines, and electrical wires. (See
OBSTACLE FREE SAFETY ZONE on cover)
CHOKING HAZARD/SHARP EDGES & POINTS
Adult assembly required. This product contains small
parts and parts with sharp edges and points. Keep parts
away from children until fully assembled.
WARNING LABEL
Owners shall be responsible for maintaining the legibility
of the warning labels.
STRANGULATION HAZARD
,seni lsehtolc,seporht iwyalpotnerdl ihcwol laREVEN•
pet leashes, cables, chains or cord-like items when using
this play-set or to attach these items to play-set.
ponchos, hoods, scarves, capes, necklaces, items with
draw-strings, cords or ties when using this play-set.
stemleht ropsroekibraewotnerdl ihcwol laREVEN•
when using this play-set.
Failure to prohibit these items, even helmets with chin
straps, increases the risk of serious injury and death to
children from entanglement and strangulation.
TIP OVER HAZARD
Choose a level location for the equipment. This can reduce
the likelihood of the play set tipping over and loose-fill
surfacing materials washing away during heavy rains.
DO NOT allow children to play on the play-set until the
assembly is complete and the unit is properly anchored.
Never add extra length to chain or rope. The chains or ropes
provided are the maximum length designed for the swinging
element(s).
WARNING
eeS. t es- ya l pruoyf osno i t a t imi ly t i capacevresbO
front cover.
gn i so l cnet oo f l l u fdnagn i t t fil l ewh t iwne rd l i hcsse rD
footwear.
retnecehtnithgi ewl lufr i ehtht iwt isotnerdl ihchcaeT
of the swing seat to prevent erratic swing motion or
falling off.
, gn i ss im; doowdekcarcronekorb, dere tn i l psrofkcehC
loose, or sharp edged hardware. Replace, tighten and or
sand smooth as required prior to playing.
n i ahc, s r edda lepor, seporgn i bmi l cdednepsust ah ty f i r eV
or cable are secured at both ends and cannot be looped
back on itself as to create an entanglement hazard.
r eh t odnaed i l seh tkcehc, syadt ohrodnaynnusnO
plastic rides to assure that they are not very hot as to
cause burns. Cool hot slide and rides with water and wipe
dry prior to using.
r aewt oo f l eehr oeo tnepor aewo tne rd l i hcwo l l at onoD
like sandals, flip–flops or clogs.
dniheb,neewteb, tnor fni,klawotnerdl ihcwol latonoD
or close to moving rides.
poolroseporrosniahcgniwstsiwtnerdl ihcteltonoD
them over the top support bar. This may reduce the
strength of the chain or rope and cause premature failure.
.noi tomnierayehtel ihwsedi rf fotegnerdl ihcteltonoD
. t ews i t inehwt nemp i uqenogn i bmi l ct imr ept onoD
an i t nemp i uqef oesur oy a l phguo rt imr ept onoD
manner for which it was not intended. Standing on or
jumping from the roof, elevated platforms, swings,
climbers, ladders or slide can be dangerous.
.staesrosedi rytpmegniwsotnerdl ihcwol latonoD
rotsrfidaehed i l snwodogo tne rd l i hcwo l l at onoD
run up slide.
WARNING – Safe Play Instructions
Orientate slide such that it gets the least amount of exposure
to the sun.

3
One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing
protective surfacing under and around your play equipment. The protective surfacing should be applied to a depth that is suitable
for the equipment height in accordance with ASTM F1292. There are different types of surfacing to choose from; whichever
product you select, follow these guidelines:
Loose-Fill Materials
• Maintain a minimum depth of 9 inches of loose-fill materials such as wood mulch/chips, engineered wood fiber (EWF), or
shredded/recycled rubber mulch for equipment up to 8 feet high; and 9 inches of sand or pea gravel for equipment up to 5 feet
high. NOTE: An initial fill level of 12 inches will compress to about a 9-inch depth of surfacing over time. The surfacing will also
compact, displace, and settle, and should be periodically raked and refilled to maintain at least a 9-inch depth.
• Use a minimum of 6 inches of protective surfacing for play equipment less than 4 feet in height. If maintained properly, this
should be adequate. (At depths less than 6 inches, the protective material is too easily displaced or compacted.)
NOTE: Do not install home playground equipment over concrete, asphalt, or any other hard surface. A fall onto a hard surface
can result in serious injury to the equipment user. Grass and dirt are not considered protective surfacing because wear and
environmental factors can reduce their shock absorbing effectiveness. Carpeting and thin mats are not adequate protective
surfacing. Ground level equipment -- such as a sandbox, activity wall, playhouse or other equipment that has no elevated play
surface -- does not need any protective surfacing.
• Use containment, such as digging out around the perimeter and/or lining the perimeter with landscape edging. Don’t forget to
account for water drainage.
• Periodically rake, check and maintain the depth of the loose-fill surfacing material. Marking the correct depth on the play
equipment support posts will help you to see when the material has settled and needs to be raked and or replenished. Be sure to
rake and evenly redistribute the surfacing in heavily used areas.
• Do not install loose fill surfacing over hard surfaces such as concrete or asphalt.
Poured-In-Place Surfaces or Pre-Manufactured Rubber Tiles
You may be interested in using surfacing other than loose-fill materials - like rubber tiles or poured-in-place surfaces.
• Installations of these surfaces generally require a professional and are not “do-it yourself ” projects.
• Review surface specifications before purchasing this type of surfacing. Ask the installer/manufacturer for a report showing that
the product has been tested to the following safety standard: ASTM F1292 Standard Specification for Impact Attenuation of Surfacing
Materials within the Use Zone of Playground Equipment. This report should show the specific height for which the surface is intended
to protect against serious head injury. This height should be equal to or greater than the fall height - vertical distance between a
designated play surface (elevated surface for standing, sitting, or climbing) and the protective surfacing below - of your play equipment.
• Check the protective surfacing frequently for wear.
Placement
Proper placement and maintenance of protective surfacing is essential. Refer to diagram on front cover. Be sure to;
• Extend surfacing at least 6 feet from the equipment in all directions.
• For to-fro swings, extend protective surfacing in front of and behind the swing to a distance equal to twice the height of the top
bar from which the swing is suspended.
• For tire swings, extend surfacing in a circle whose radius is equal to the height of the suspending chain or rope, plus 6 feet in all directions.
Protective Surfacing - Reducing Risk of Serious Head Injury From Falls
From the CPSC Outdoor Home Playground Safety Handbook. At http://www.playgroundregs.com/resources/CPSC%20324.pdf
Denotes Use Zone with Protective Surfacing
Denotes Use Zone with Protective Surfacing
6 ft.
6 ft. 6 ft.
6 ft.
6 ft. 6 ft.
6 ft.
Use Zone for Multi-Axis SwingsUse Zone for Single-Axis Swings

4
Instructions for Proper Maintenance
HARDWARE:
Check metal parts for rust. If found,
sand and repaint using a non-lead
paint complying with 16 CFR 1303.
Inspect and tighten all hardware. On
wood assemblies DO NOT OVER-
TIGHTEN as to cause crushing and
splintering of wood.
Check for sharp edges or protruding screw threads, add
washers if required.
SHOCK ABSORBING SURFACING:
Check for foreign objects. Rake and check depth of loose
fill protective surfacing materials to prevent compaction
and maintain appropriate depth. Replace as necessary.
(See Protective Surfacing, page 3)
GROUND STAKES (ANCHORS):
Check for looseness, damage or deterioration. Should
firmly anchor unit to ground during use. Re-secure and
or replace, if necessary.
SWING HANGERS:
Check that bolts are secure and tight. Quick clips should
be completely closed and threaded clips screwed tight.
If squeaking occurs lubricate bushings with oil or WD-40®.
SWINGS, ROPES AND RIDES:
Reinstall if removed during cold season. Check all
moving parts including swing seats, ropes, chains and
attachments for wear, rust and other deterioration.
Replace as needed.
Check that ropes are tight, secure at both ends and
cannot loop back as to create an entrapment.
WOOD PARTS:
Check all wood members for deterioration, structural
damage and splintering. Sand down splinters and replace
deteriorated wood members. As with all wood, some
checking and small cracks in grain is normal.
Unprotected, they will appear weathered over time.
Periodic application of an exterior water repellent or stain
(water-based) will help improve appearance and life.
Your KidKraft Play System is designed and constructed of quality materials with your child’s safety in mind. As with all outdoor
products used by children, it will weather and wear. To maximize the enjoyment, safety and life of your Play Set, it is important
that you, the owner, properly maintain it.
Check the following at the beginning of the play season:
HARDWARE:
Inspect for tightness. Must be firmly against, but not
crushing the wood. DO NOT OVER-TIGHTEN.
This will cause splintering of wood.
Check for sharp edges or protruding screw threads.
Add washers if required.
SHOCK ABSORBING SURFACING:
Rake and check depth of loose fill protective surfacing
materials to prevent compaction and maintain appropriate
depth. Replace as necessary.
(See Protective Surfacing, page 3)
Check twice a month during play season:
SWING HANGERS:
Check that they are secure and orientated correctly. Hook
should rotate freely and perpendicular to support beam.
If squeaking occurs lubricate bushings with oil or WD-40®.
SWINGS AND RIDES:
Check swing seats, all ropes, chains and attachments for
fraying, wear, excessive corrosion or damage.
Replace if structurally damaged or deteriorated.
Check once a month during play season:
SWINGS AND RIDES:
To prolong their life, remove swings and store inside
when outside temperature is below 32°F/0°C. Below
freezing, plastic parts may become more brittle.
SHOCK ABSORBING SURFACING:
Rake and check depth of loose fill protective surfacing
materials to prevent compaction and maintain appropriate
depth. Replace as necessary.
(See Protective Surfacing, page 3)
Check at the end of the play season:
If you dispose of your play set: Please disassemble and dispose of your unit so that it does not create any unreasonable hazards
at the time it is discarded. Be sure to follow your local waste ordinances.
Use an extra
Flat Washer
If Bolt protrudes
beyond T-Nut

5
About Our Wood
KidKraft Premium Play Systems uses 100% FSC wood. Although we take great care in selecting the best quality lumber available,
wood is still a product of nature and susceptible to weathering which can change the appearance of your set.
What causes weathering? Does it affect the strength of my Play System?
One of the main reasons for weathering is the effects of water (moisture); the moisture content of the wood at the surface is
different than the interior of the wood. As the climate changes, moisture moves in or out of the wood, causing tension which can
result in checking and or warping. You can expect the following due to weathering. These changes will not affect the strength of
the product:
1. Checking is surface cracks in the wood along the grain. A post (4” x 4”) will experience more checking than a board (1” x 4”)
because the surface and interior moisture content will vary more widely than in thinner wood.
2. Warping results from any distortion (twisting, cupping) from the original plane of the board and often happens from rapid
wetting and drying of the wood.
3. Fading happens as a natural change in the wood color as it is exposed to sun-light and will turn a grey over time.
How can I reduce the amount of weathering to my Play System?
At the factory we have coated the wood with a water repellent or stain. This coating decreases the amount of water absorption
during rain or snow thus decreasing the tension in the wood. Sunlight will break down the coating, so we recommend applying a
water repellent or stain on a yearly basis (see your local stain and paint supplier for a recommended product).
Most weathering is just the normal result of nature and will not affect safe play and enjoyment for your child. However if you are
concerned that a part has experienced a severe weathering problem please call our consumer relations department for further assistance.
Complete and mail registration card to receive important product notifications and assure prompt
warranty service.
5Year Limited Warranty
KidKraft warrants that this product is free from defect in materials and workmanship for a period of one
year from the original date of purchase. In addition, lumber is warranted for 5years against structural
failure due to rot and insect damage. All other parts, such as hardware, swings, rides, accessories, and
slides carry a one-year warranty only.
This warranty applies to the original owner and registrant and is non-transferable.
Regular maintenance is required to assure the integrity of your Play System. This warranty does not
cover any inspection cost.
This Limited Warranty does not cover:
• Labor for replacement of any defective item(s);
• Incidental or consequential damages;
• Cosmetic defects which do not affect performance or integrity;
• Vandalism; improper use or installation; acts of nature;
•Minor twisting, warping, checking, or any other natural occurring properties of wood that do not
affect performance or integrity.
KidKraft products have been designed for safety and quality. Any modifications made to the original
product could damage the structural integrity of the unit leading to failure and possible injury.
Kidkraft cannot assume any responsibility for modified products. Furthermore, modification voids
any and all warranties.
This product is warranted for RESIDENTIAL USE ONLY. Under no circumstance should a
KidKraft Play System be used in public settings such as schools, churches, playgrounds, parks, day
cares and the like. Such use may lead to product failure and potential injury. Any and all public use
will void this warranty.
KidKraft disclaims all other representations and warranties of any kind, express or implied.
This Warranty gives you specific legal rights. You may have other rights as well which vary from state to state or
province to province. This warranty excludes all consequential damages, however, some states do not allow the
limitation or exclusion of consequential damages, and therefore this limitation may not apply to you.

6
This identifies information that requires special
attention. Improper assembly could lead to an unsafe
or dangerous condition.
Where this is shown, 2 or 3 people
are required to safely complete the
step. To avoid injury or damage
to the assembly make sure to get
help!
Check that assembly is square
before tightening bolts.
Use a measuring tape to assure
proper location.
Check that set or assembly is properly level
before proceeding.
Pre-drill a pilot hole
before fastening screw
or lag to prevent
splitting of wood.
This indicates time to tighten bolts, but
not too tight! Do not crush the wood.
This may create splinters and cause
structural damage.
Part Identification Key
On each page, you will find the parts
and quantities required to complete the
assembly step illustrated on that page.
Here is a sample.
Key Number: The first two digits
represent the step number. The third
digit represents the piece. Note that if
the part is used in multiple steps then
the number only reflects the first step it
is used in.
Symbols
Throughout these instructions symbols are provided as important reminders for proper and safe assembly.
Proper Hardware Assembly
Lag screws require drilling pilot
holes to avoid splitting wood. Only
a flat washer is required. For ease of
installation liquid soap can be used
on all lag-type screws.
For bolts, tap T-Nut into hole with
hammer. Insert the hex bolt through
lock washer first then flat washer then
hole. Because the assemblies need to
be squared do not completely tighten
until instructed. Pay close attention to
diameter of the bolts. 5/16” is slightly
larger than 1/4”.
Note: Wafer head bolts with blue lock
tight or a bolt with a Ny-Lok nut do
NOT require a lock washer.
Once the assembly is tightened, watch for exposed threads.
If a thread protrudes from the T-Nut, remove
the bolt and add washers to eliminate this condition.
Extra washers have been provided for this purpose.
Use
Help
Use
Help
Measure
Distance
Square
Assembly
Use
Level
Pre-drill 1/8” & 3/16” Bit
Tighten
Bolts
CAUTION – Protrusion Hazard
Keys to Assembly Success
Tools Required
• Tape Measure
• Carpenters Level
• Carpenters Square
• Claw Hammer
• Standard or Cordless Drill
• #1 Phillips, #2 Robertson
and Screwdriver
• Ratchet with extension
(1/2” & 9/16” sockets)
• Open End Wrench
(1/2” & 9/16”)
• Adjustable Wrench
• 1/8” & 3/16” Drill Bits
• 3/16” Hex Key
• 8’ Step Ladder
• Safety Glasses
• Adult Helpers
• Pencil
Quantity Key Number Part Description,
Part Size
2X 012 Post 2 x 4 x 83”
No Yes
Lag Assembly
Bolt Assembly
Flat Washer
Lag Screw
Hex Bolt
Lock
Washer
Flat
Washer
Before mounting Lag
Screw, use factory drilled
holes as guides to drill 1/8”
pilot holes
T-Nut
(Hammer into place)
Do not crush wood!
If Bolt protrudes
beyond T-Nut
Use an extra
flat washer

7
1 inch = 25.4mm
KIDKRAFT DESIGN HARDWARE
For example:
BOLT LENGTH 4½ (4.5) inches long
114mm long
1 inch = 25.4mm
25.4mm
4.5 inches x
DIAMETER CONVERSION
LENGTH CONVERSION
=
BOLT DIAMETER 5/16 (0.31) inches 0.31 inches x 25.4mm = 8mm
For example:
HARDWARE LENGTH CHART
inches vs millimetres
6 152
5½ 140
5 127
4½ 114
4 102
3½ 89
3 76
2½ 64
2 51
1½ 38 1¼ 32
1-1/8 29
1 25.4
7/8 22 3/4 19 1/2 12.7
1/4" (6mm) Flat Washer
1/4" (6mm) Lock Washer
1/4"(0.25) = 6mm Hex Bolt
1/4" (6mm) T-Nut
5/16"(.31) = 8mm Lag Screw
5/16" (8mm) Flat Washer
1/4"(0.25) = 6mm Lag Screw
1/4" (6mm) Flat Washer
5/16" (8mm) Flat Washer
5/16" (8mm) Lock Washer
5/16"(.31) = 8mm Hex Bolt
5/16" (8mm) T-Nut
3/8"(.38) = 9.5mm Lag Screw
3/8" (9.5mm) Flat Washer

8
1 x 2 1 x 4 1 x 5
1 x 6
1 x 3
1/2 x 4
5/4 x 6
5 1/2"
139.7
1"
25.4
11.1
.44
82.6
3 1/4"
4 x 4
3 1/2"
88.9
3 1/2"
88.9
4 1/2"
114.3
5/8"
15.9
15.9
5/8" 1 3/8"
34.9
2 x 6
5 3/8"
136.5
1 1/2"
38.1
15.9
5/8" 3 3/8"
85.7
60.3
2 3/8"
15.9
5/8"
1505mm
KIDKRAFT DESIGN WOOD PROFILES
LENGTH CONVERSION
For example:
1 inch = 25.4mm
BOARD LENGTH 59¼ (59.25) inches 59.25 inches x 25.4mm =
Dimensions in brackets [mm] represent millimetres.
5/4 x 4
3 1/2"
88.9
1"
25.4
5 3/8"
136.5
5/8"
15.9
2 x 4
3 3/8"
85.7
1 3/8"
34.9
5/4 x 5
4 1/2"
114.3
1"
25.4 2 x 3
2 1/2"
63.5
1 3/8"
34.9
5/4 x 3
63.5
2 1/2"
25.4
1"
2 x 2
1 1/2"
38.1
1 1/2"
38.1

9
(4) 2793 - 1-1/4 x 3 x 18-3/4" - Long Roof End - 3632793
2pc. -2802 Transom Window
1¼ x 19 x 43"
37632802
2x - Sky Gable
(3320212)
(4) 2788 -1-1/4 x 2-1/2 x 37-1/8" - Mid Roof Support - 3632788
(4) 2790 - 1 x 5 x 15½" - Transom Board A - 3632790
(4) 2791 - 1 x 6 x 11" - Transom Board B - 3632791
(4) 2789 - 5/4 x 3 x 40 - Short Wall Tie - 3632789
(2) 48" High Rail Slide
3310148
(5) 2609 - 1 x 5 x 40-5/8" - Floor Board - 3632609
Bracket (3 Pk)
- Flat Panel Bracket (4 Pk)
1x
(3200640)
(3200641)
1x - Narrow Angle
1x - ADD ON C Bracket Set (3204910)
2pc. -2677
Narrow Panel 1¼ x 22 x 87"
37632677
1pc. -2671
Back Small Roof 1¼ x 22-9/16 x 33-3/8"
37632671
1pc. -2672
Front Small Roof 1¼ x 22-9/16 x 33-5/8"
37632672
(2) 2680 -1-1/4 x 2-1/4 x 34.10" - Roof Support - 3632680
(2) 2684 -1-1/4 x 4-7/8 x 7" - Mid Roof End - 3632684
1x -Spiral Wave Bracket (2PK)
(3201500)
3pc. -2655
Upper Window Insert 1.27 x 18.8 x 35.86"
37632655
ADD ON M Parts I.D.
(1) 2795 -1-1/4 x 3 x 84-3/4" - Long Joist - 3632795
(2) 2792 -1-1/4 x 3 x 43-3/4" - Ground Brace - 3632792
(2) 2794 -2 x 2 x 44-3/8" - Joist - 3632794

10
Hardware Identification (Actual Size)
31pc. S3 - Wood Screw #8 x 2-1/2" - (52043522)
41pc. S0 - Truss Screw #8 x 7/8" - (52933505)
8pc. S5 - Pan Screw #8 x 1/2" - (9264504)
2pc. TN1 - 1/4" T - Nut
(54503200)
2pc. LW1 - 1/4" Lock Washer
(51303200)
22pc. S8 - Pan Screw #12 x 3/4" - (52433603)
3pc. S7 - Pan Screw #12 x 2" - (52433620)
45pc. S11 - Wood Screw #8 x 2" - (52043520)
65pc. S2 - Wood Screw #8 x 1-1/2" - (52043512)
2pc. H11 - Hex Bolt 1/4 x 2-3/4" - (53703223)
12pc. S4 - Wood Screw #8 x 3" - (52043530)
2pc. FW1 - 1/4" Flat Washer
(51103200)
Add On M Hardware

11
(1) Door Stop 5/4 x 3 x 10"
3632715
2715
1.27 x 18.8 x 41.9" 37632649
(1) Lower Window Insert
2649
(1) Lower Jamb 1¼ x 3 x 41-15/16"
2601
3632601
1¼ x 15¾ x 40¾" 37602709B
(1) Door Window Panel
2709
1x Magnetic Catch
1x Catch Plate
Door Handle
9207713
Door Hinge
2x 9201713
Door Catch
2x 9207711
1x - Door Hardware (3201710)
(1) Jamb Mount -2 PK (3206301)
4pc. S18 - Wood Screw #6 x 1" - (52013910)
16pc. S13 - Pan Screw #6 x 5/8" - (52413908)
3pc. S11 - Wood Screw #8 x 2" - (52043520)
17pc. S0 - Truss Screw #8 x 7/8" - (52933505)
Part Identification (Reduced Part Size)
Part Identification (Actual Part Size)
Add On B Part & Hardware

12
1pc. -2685 - 1 x 4 x 40-5/8" - Counter Top - 3632685
1x - Sky Chalk Wall
(3320217)
1x - Deluxe Kitchen Set
(3320969)
2pc. -2716 - 1 x 4 x 17-5/8" - Counter Mid Top - 3632716
2pc. -2683 - 5/4 x 3 x 62-5/8" - Wall Tie 3632683
2pc. -5536 - 5/8 x 2 x 6-3/4" - Counter Side - 38045536
1pc. -2686 - 5/8 x 2-3/4 x 40-5/8" - Counter Front - 3632686
2pc. -2682 - 2 x 2 x 22-1/8" - Short Side Joist - 3632682
1pc. -2687 - 1 x 4 x 40-5/8" - Counter Back - 3632687
2pc. -6136 - 1 x 2 x 12-9/16" - Counter Brace
38046136
1x - Flag and Pole (2pk)
(3320632)
1pc. -2681 - 1-1/4 x 3 x 62-5/8" - Long Floor Joist - 3632681
4pc. -5736 - 1 x 2 x 8 1/4" - Counter Joist
38045736
1x - Sky Gable
(3320212)
5pc. -2609 - 1 x 5 x 40-5/8" - Floor Board - 3632609
1pc. -2689
Gable Dormer Lt 1¼ x 14.6 x 22"
37632689
1pc. -2688 - Dormer Cleat 1¼ x 3 x 12¾" - 3632688
ADD ON C Parts (Reduced Part Size)
1pc. -2608 - 1-1/4 x 3 x 40-3/4" - Floor Joist - 3632608
1pc. -2672
Front Small Roof 1¼ x 22-9/16 x 33-5/8"
37632672
1pc. -2671
Back Small Roof 1¼ x 22-9/16 x 33-3/8"
37632671
Bracket (3 Pk)
- Flat Panel Bracket (4 Pk)
1x
(3200640)
(3200641)
1x - Narrow Angle
1x -ADD ON C Bracket Set (3204910)
1pc. -2649
Lower Window Insert
1.27 x 18.8 x 41.91"
37632649
2pc. -2684 - 1-1/4 x 4-7/8 x 7" - Mid Roof End - 3632684
Nominal Size Actual Size
2 x 2 1-1/2 x 1-1/2
1 x 2 1 x 2
1 x 5 5/8 x 4-1/2
1 x 6 5/8 x 5-3/8
1-1/4 x 3 1-1/4 x 3
1-1/4 x 2-1/4 1-1/4 x 2-1/4
1-1/4 x 4-7/8 1-1/4 x 4-7/8
2pc. -2677
Narrow Panel 1¼ x 22 x 87"
37632677
2pc. -2680 - 1-1/4 x 2-1/4 x 34.10" - Roof Support - 3632680
2pc. -649A
Short Half Wall
1.27 x 18.8 x 20-15/16"
37632649A
1pc. -2699
Gable Dormer Rt 1¼ x 14.6 x 22"
37632699

13
12pc. S3 - Wood Screw #8 x 2-1/2" - (52043522)
Part Identification (Actual Part Size)
2pc. H11 -Hex Bolt 1/4 x 2-3/4" - (53703223)
1pc. S4 - Wood Screw #8 x 3" - (52043530)
21pc. S0 - Truss Screw #8 x 7/8" - (52933505)
2pc. TN1 - 1/4" T - Nut
(54503200)
2pc. LW1 - 1/4" Lock Washer - (51303200)
2pc. FW1 - 1/4" Flat Washer - (51103200)
8pc. S5 - Pan Screw #8 x 1/2" - (52433502)
30pc. S11 - Wood Screw #8 x 2" - (52043520)
20pc. TS - Trim Screw #6 x 30mm - (52953911)
16pc. S8 - Pan Screw #12 x 3/4"
- (52433603)
9pc. S10 - Pan Screw #8 x 1"
- (52433510)
44pc. S2 - Wood Screw #8 x 1-1/2" - (52043512)
Add On C Hardware

14
Nominal Size Actual Size
5/4 x 515/16 x 4-1/4
5/4 x 615/16 x 5-1/4
2x 2 1-1/2 x 1-1/2
1x 4 5/8 x 3-3/8
1x 6 5/8 x 5-3/8
1-1/4 x 2-1/4 1-1/4 x 2-1/4
1-1/4 x 3 1-1/4 x 3
4 x 43x 3
4 x 63 x 5-1/4
Box 1,2 of 6
1x
2x
2616
2611
"
"
1x
1x
1x
1x
1x
1x KidKraft
9320374
1x
1x
1x
1x
1x
1x
1x
2x
2x
1x
2612
Kidkraft Logo Plaque
(3320353)
(Main Clubhouse and Swing)

15
1pc. -2644
Front Roof Panel 1¼ x 37 x 44"
Box 2 - 37632644
1pc. -2639
Back Roof Panel 1¼ x 36¾ x 44"
Box 2 - 37632639
1pc. -2627
SW Wall Panel 1¼ x 42 x 87"
Box 2 - 37632627
2pc. -2618 Front Back
Panel 1¼ x 42 x 87"
Box 2 - 37632618
Part Identification (Reduced Part Size)
Lower Window Insert
1.27 x 18.8 x 35.86"
1.27 x 18.8 x 41.91"
2pc.
Upper Window Insert
Box 2 - 37632649
2655
-
Box 2 - 37632655
1pc. -2649
1pc.
MOD 3 Pane Transom (2Pk)
Box 1 - 3320138
Short Half Wall - 1.27 x 18.8 x 20-15/16"
Box 2 - 37632649A
649A2pc. -
1pc. -2665
Half Wall Insert - 1.4 x 20¼ x 38.8"
Box 2 - 37632665
1pc. -2622
End Panel Assembly 1¼ x 42 x 87"
Box 2 - 37632622
(Main Clubhouse and Swing)

16
5pc. BN1 - 1/4" Barrel Nut - (54803200)
12pc. FW1 - 1/4" Flat Washer - (51103200)
29pc. LN2 - 5/16" Lock Nut - (54303300)
69pc. S0 - Truss Screw #8 x 7/8" - (52933505)
5pc. LW2 - 5/16" Lock Washer - (51303300)
12pc. S4 - Wood Screw #8 x 3" - (52043530)
13pc. S7 - Pan Screw #12 x 2" - (52433620)
14pc. S3 - Wood Screw #8 x 2-1/2" - (52043522)
8pc. TN2 - 5/16" T- Nut - (54503300)
2pc. S6 - Pan Screw #12 x 1"
- (52433610)
Hardware Identification (Actual Size)
5pc. FW0 - 3/16" Flat Washer - (51103100)
5pc. S10 - Pan Screw #8 x 1"
- (52433510)
10pc. TN1 - 1/4" T - Nut
(54503200)
66pc. FW2 - 5/16" Flat Washer - (51103300)
15pc. LW1 - 1/4" Lock Washer - (51303200)
77pc. S2 - Wood Screw #8 x 1-1/2" - (52043512)
1pc. D4 - 2 x 2 Robertson Driver Bit - (9200014)
8pc. FW3 - #8 Flat Washer - (51003500)
28pc. S11 - Wood Screw #8 x 2" - (52043520)
20pc. S5 - Pan Screw #8 x 1/2" - (52433502)
5pc. PB2 - Pan Bolt 1/4 x 1-1/4"
- (53433212)
4pc. S18 - Wood Screw #6 x 1" - (52013910)
(Main Clubhouse and Swing)

17
2pc. LS3 - Lag Screw 1/4 x 3" - (52213230)
Hardware Identification (Actual Size) Box 1,2 of 6
4pc. G8 - Hex Bolt 5/16 x 2"
- (53703320)
3pc. G4 - Hex Bolt 5/16 x 4" - (53703340)
14pc. G7 - Hex Bolt 5/16 x 5-1/2" - (53703352)
4pc. H1 - Hex Bolt 1/4 x 1-1/2" - (53703212)
2pc. H10 - Hex Bolt 1/4 x 2-1/4" - (53703221) 4pc. H11 - Hex Bolt 1/4 x 2-3/4" - (53703223)
2pc. G25 - Hex Bolt 5/16 x 7-1/4" - (53703371)
16pc. WL5 - Wafer Lag 1/4 x 2-1/2"
- (52613222)
7pc. G21 - Hex Bolt 5/16 x 3-3/4" - (53703333)
3pc. WB7 - Wafer Bolt 5/16 x 3" - (53613330)
(Main Clubhouse and Swing)

18
Adventure Tower
2pc. - 6008 - 38.1 x 38.1 x 336.6mm Tarp Uprght - Box 1 -
3636008
1pc. - 6005 - 31.8 x 82.6 x 222.3mmTNR Slide Block - Box 1 -
3636005
1pc. - 6004 - 23.8 x 82.6 x 409.6mm Box Bottom - Box 1 -
3636004
2pc. - 6015 - 23.8 x 82.6 x 444.5mm Box Leg - Box 1 -
3636015
1pc. - 8832 - 23.8 x 82.6 x 362mm - Box End - Box 1 -
3638832
2pc. - 8834
-
23.8 x 82.6 x 216mm - Box Gusset FSC - Box 1 -
3638834
1pc. - 6027 - 23.8 x 82.6 x 596.9mm Sand Water Support - Box 1 -
3636027
1pc. - 6021 - 15.9 x 114.3 x 596.9mm Back Ground - Box 1 -
3636021
1pc. - 6014 - 31.8 x 76.2 x 430.2mm Tunnel Spacer - Box 1 -
3636014
2pc. - 6001 - 31.8 x 82.6 x 406.4mm Gusset - Box 1 -
3636001
2pc. - 6006 - 31.8 x 82.6 x 396.9mm Back Gusset - Box 1 -
3636006
1pc. - 0600 - 15.9 X 101.6 X 596.9mm Bottom Trim - Box 1 -
3620600
2pc. - 0601 - 15.9 x 76.2 x 500mm Side Trim - Box 1 -
3620601
2pc. - 0602 - 15.9 x 76.2 x 420mm Short Trim - Box 1 -
3620602
7pc. - 6013 - 15.9 x 108 x 533.4mm Floor Board - Box 1 -
3636013
1pc. - 6028 - 23.8 x 82.6 x 644.5mm Top Back - Box 1 -
3636028
1pc. - 0603 - 15.9 X 82.6 X 644.5mm Top Trim - Box 1 -
3620603
1pc. - 6042 - 15.9 x 98 x 533.4mm Narrow Floor Board - Box 1 -
3636042
Actual Size
1½" x 1½"
1½" x 5⅜"
Nominal Size
2 x 2
2 x 6
Actual Size
1½" x 1½"
1⅜" x 2½"
1⅜" x 3⅜"
Nominal Size
2 x 2
2 x 3
2 x 4
Actual Size
1" x 3½"
1" x 4½"
1
" x 5½"
1⅜" x 2½"
Nominal Size
5/4 x 4
5/4 x 5
5/4 x 6
2 x 3
Nominal Size
1 x 5
1 x 6
5/4 x 2
5/4 x 3
5/4 x 4
Actual Size
⅝
" x 4½"
⅝
" x 5⅜"
1
" x 1⅜"
1" x 2½"
1" x 3½"
Actual Size
⅝
" x 3⅜"
⅝
" x 4½"
⅝
" x 5⅜"
Nominal Size
1 x 4
1 x 5
1 x 6
Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size)
Nominal Size
½
x 4
1 x 2
1 x 3
1 x 4
Actual Size
7
16
" x 3¼"
⅝" x 1⅜"
⅝" x 2⅜"
⅝" x 3⅜"

19
Adventure Tower
2pc. - 6011 - 23.8 x 82.6 x 768.4mm Box Side - Box 1 -
3636011
1pc. - 0369 - 34.9 x 63.5 x 939.8mm Lower Diagonal - Box 1 -
3640369
1pc. - 6032 - 31.8 x 108 x 874mm TNR Wall - Box 1 -
3636032
2pc. - 6012 - 31.8 x 82.6 x 933.6mm Short Post - Box 1 -
3636012
2pc. - 6017 - 31.8 x 82.6 x 875.3mm Floor Support - Box 1 -
3636017
1pc. - 6003 - 23.8 x 50.8 x 862.2mm Floor Joist - Box 1 -
3636003
1pc. - 6022 - 31.8 x 63.5 x 616mm SL Brace - Box 1 -
3636022
1pc. - 6019 - 15.9 x 133.4 x 596.9mm Rock Bottom -
Box 1 -
3636019
4pc. - 6010 - 15.9 x 133.4 x 596.9mm Rock Board A -
Box 1 -
3636010
5pc. - 6009 - 15.9 x 133.4 x 596.9mm Rock Board B -
Box 1 -
3636009
1pc. - 6029 - 23.8 x 82.6 x 784.2mm Side Top - Box 1 -
3636029
1pc. - 6030 - 23.8 x 82.6 x 784.2mm Tunnel Side Top - Box 1 -
3636030
2pc. - 6033 - 15.9 x 63.5 x 996.9mm Post Support - Box 1 -
3636033
1pc. - 6025 - 38.1 x 38.1 x 901.7mm Tarp Support - Box 1 -
3636025
2pc. - 6023 - 15.9 x 82.6 x 1019.2mm Roof Side - Box 1 -
3636023
2pc. - 6024 - 15.9 x 82.6 x 901.7mm Tarp End - Box 1 -
3636024
1pc. - 6034 - 23.8 x 139.7 x 596.9mm Floor Back -
Box 1 -
3636034
Actual Size
1½" x 1½"
1½" x 5⅜"
Nominal Size
2 x 2
2 x 6
Actual Size
1½" x 1½"
1⅜" x 2½"
1⅜" x 3⅜"
Nominal Size
2 x 2
2 x 3
2 x 4
Actual Size
1" x 3½"
1" x 4½"
1
" x 5½"
1⅜" x 2½"
Nominal Size
5/4 x 4
5/4 x 5
5/4 x 6
2 x 3
Nominal Size
1 x 5
1 x 6
5/4 x 2
5/4 x 3
5/4 x 4
Actual Size
⅝
" x 4½"
⅝
" x 5⅜"
1
" x 1⅜"
1" x 2½"
1" x 3½"
Actual Size
⅝
" x 3⅜"
⅝
" x 4½"
⅝
" x 5⅜"
Nominal Size
1 x 4
1 x 5
1 x 6
Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size)
Nominal Size
½
x 4
1 x 2
1 x 3
1 x 4
Actual Size
7
16
" x 3¼"
⅝" x 1⅜"
⅝" x 2⅜"
⅝" x 3⅜"

20
Adventure Tower
2pc. - 6002 - 31.8 x 82.6 x 1968.5mm Long Post - Box 1 -
3636002
1pc. - 6020 - 15.9 x 114.3 x 1122mm Short Ground - Box 1 -
3636020
1pc. - 6018 - 15.9 x 114.3 x 1576.1mm Long Ground - Box 1 -
3636018
2pc. - 6026 - 31.8 x 69.9 x 1827mm Rock Rail - Box 1 -
3636026
2pc. - 6000 - 31.8 x 82.6 x 1495.4mm Upper Post - Box 1 -
3636000
2pc. - 6007 - 31.8 x 76.2 x 1095.4mm Wall Support - Box 1 -
3636007
4pc. - 6031 - 15.9 x 72.6 x 996.9mm Window Brace - Box 1 -
3636031
1x - Maze N Wave 2.35m Slide
(3318215) - Green
2x - LDPE
Drain Plug
(9320703)
1x - Shovel
(9320326)
2x - Steel Hand Grip
(9200311) - Red
1x - Telescope w/ Mount
(3320161)
1x - Flag and
Pole (2 Pk)
(3320632)
1x - Tower Canopy (3754810)
1x - Corner
Brace (4 Pk)
(3200164)
1x - Rocks (9pk) (3320100)
(Green/Burgundy
)
1x - Rebar Ground
Stake (2 Pk)
(3200318)
1x -Seat
(9320123)
2x -Plug
(9320703)
1x -Shovel
(9320326)
1x -3 in 1 Bench Set (3320123)
1x - Sand and Water Insert
(9320105)
Actual Size
1½" x 1½"
1½" x 5⅜"
Nominal Size
2 x 2
2 x 6
Actual Size
1½" x 1½"
1⅜" x 2½"
1⅜" x 3⅜"
Nominal Size
2 x 2
2 x 3
2 x 4
Actual Size
1" x 3½"
1" x 4½"
1
" x 5½"
1⅜" x 2½"
Nominal Size
5/4 x 4
5/4 x 5
5/4 x 6
2 x 3
Nominal Size
1 x 5
1 x 6
5/4 x 2
5/4 x 3
5/4 x 4
Actual Size
⅝
" x 4½"
⅝
" x 5⅜"
1
" x 1⅜"
1" x 2½"
1" x 3½"
Actual Size
⅝
" x 3⅜"
⅝
" x 4½"
⅝
" x 5⅜"
Nominal Size
1 x 4
1 x 5
1 x 6
Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size)
Nominal Size
½
x 4
1 x 2
1 x 3
1 x 4
Actual Size
7
16
" x 3¼"
⅝" x 1⅜"
⅝" x 2⅜"
⅝" x 3⅜"