KidKraft Cedar Summit COPPER RIDGE PLAYSET User manual

INSTALLATION AND OPERATING INSTRUCTIONS
Table of Contents
Warnings and Safe Play Instructions..........pg. 2
Protective Surfacing Guidelines. . . . . . . . . . . . . . . pg. 3
Instructions for Proper Maintenance .........pg. 4
About Our Wood – Limited Warranty.........pg. 5
Keys to Assembly Success ....................pg. 6
Part ID pg. 10-19
Step-By-Step Instructions ...................pg. 20
Installation of I.D./Warning Plaque......Final Step
To reduce the risk of serious injury or death, you must read and
follow these instrucons. Keep and refer to these instrucons
oen and give them to any future owner of this play set.
Manufacturer contact informaon provided below.
OBSTACLE FREE SAFETY ZONE - 32’ 6” x 27’11” (9.9 x 8.51 m) area requires Protecve Surfacing. See page 3.
MAXIMUM VERTICAL FALL HEIGHT - 7’ 8” (2.34m)
CAPACITY - 16 Users Maximum, Ages 3 to 10; Weight Limit 110 lbs. (49.9 kg) per child.
RESIDENTIAL HOME USE ONLY. Not intended for public areas such as mul-unit residences, schools, churches,
nurseries, day cares or parks.
Warning. Only for domesc use.
WARNING
Rev 10/23/2018
Cedar Summit by KidKraft
4630 Olin Road
Dallas, TX 75244, United States
[email protected]
Online Parts Replacement:
Cedarsummitplay.com/parts-center-warranty-claim
Customer Service:
1(800) 933-0771 or [phone]
KidKraft Netherlands BV
Olympisch Stadion 29
1076DE Amsterdam, The Netherlands
Europe Customer Service: [phone]
[e-mail]
EU Online Parts Replacement: parts.kidkraft.eu
For Outdoor Family Domestic Use Only
14 - 18 Hrs
FOR FORT & SWING
TWO PERSON
ASSEMBLY
2-4 Hrs
10 - 12 Hrs
FOR FORT & SWING
TWO PERSON
ASSEMBLY
10 - 12 Hrs
FOR FORT & SWING
1 - 2 Hrs
TUBE SLIDE
354cm
574cm
851cm
974cm
F29055 - Copper Ridge Playset Safety Zone
32' 6"
9.9 m
18' 8.6"
5.705 m
11' 7.56"
3.545 m
27' 11"
8.51 m
COPPER
RIDGE
PLAYSET
F29055E

Warnings and Safe Play Instructions
CONTINUOUS ADULT SUPERVISION REQUIRED. Most serious injuries and deaths on playground equipment have occurred
while children were unsupervised! Our products are designed to meet mandatory and voluntary safety standards. Complying
with all warnings and recommendations in these instructions will reduce the risk of serious or fatal injury to children using
this play system. Go over the warnings and safe play instructions regularly with your children and make certain that they
understand and follow them. Remember on-site adult supervision is required for children of all ages.
SERIOUS HEAD INJURY HAZARD
Installation over concrete, asphalt, dirt, grass, carpet
and other hard surface creates a risk of serious injury
or death from falls to the ground. Install and maintain
shock absorbing material under and around play-set as
recommended on page 3 of these instructions.
COLLISION HAZARD
Place play-set on level ground at least 2m from any
obstruction such as a garage or house, fences, poles,
trees, sidewalks, walls, landscape timbers, rocks,
pavement, planters, garden borders, overhanging
branches, laundry lines, and electrical wires. (See
OBSTACLE FREE SAFETY ZONE on cover)
CHOKING HAZARD/SHARP EDGES & POINTS
Adult assembly required. This product contains small
parts and parts with sharp edges and points. Keep parts
away from children until fully assembled.
WARNING LABEL
Owners shall be responsible for maintaining the legibility
of the warning labels.
STRANGULATION HAZARD
,senilsehtolc,seporhtiwyalpotnerdlihcwollaREVEN•
pet leashes, cables, chains or cord-like items when using
this play-set or to attach these items to play-set.
ponchos, hoods, scarves, capes, necklaces, items with
draw-strings, cords or ties when using this play-set.
stemlehtropsroekibraewotnerdlihcwollaREVEN•
when using this play-set.
Failure to prohibit these items, even helmets with chin
straps, increases the risk of serious injury and death to
children from entanglement and strangulation.
TIP OVER HAZARD
Choose a level location for the equipment. This can reduce
the likelihood of the play set tipping over and loose-fill
surfacing materials washing away during heavy rains.
D
Never add extra length to chain or rope. The chains or ropes
provided are the maximum length designed for the
swinging element(s)
O NOT allow children to play on the play-set until the
assembly is complete and the unit is properly anchored.
WARNING
eeS.tes-yalpruoyfosnoitatimilyticapacevresbO
front cover.
gnisolcnetoofllufdnagnittfillewhtiwnerdlihcsserD
footwear.
retnecehtnithgiewllufriehthtiwtisotnerdlihchcaeT
of the swing seat to prevent erratic swing motion or
falling off.
,gnissim;doowdekcarcronekorb,deretnilpsrofkcehC
loose, or sharp edged hardware. Replace, tighten and or
sand smooth as required prior to playing.
niahc,sreddalepor,seporgnibmilcdednepsustahtyfireV
or cable are secured at both ends and cannot be looped
back on itself as to create an entanglement hazard.
rehtodnaedilsehtkcehc,syadtohrodnaynnusnO
plastic rides to assure that they are not very hot as to
cause burns. Cool hot slide and rides with water and wipe
dry prior to using.
raewtoofleehroeotneporaewotnerdlihcwollatonoD
like sandals, flip–flops or clogs.
dniheb,neewteb,tnorfni,klawotnerdlihcwollatonoD
or close to moving rides.
poolroseporrosniahcgniwstsiwtnerdlihcteltonoD
them over the top support bar. This may reduce the
strength of the chain or rope and cause premature failure.
.noitomnierayehtelihwsedirffotegnerdlihcteltonoD
.tewsitinehwtnempiuqenognibmilctimreptonoD
anitnempiuqefoesuroyalphguortimreptonoD
manner for which it was not intended. Standing on or
jumping from the roof, elevated platforms, swings,
climbers, ladders or slide can be dangerous.
.staesrosedirytpmegniwsotnerdlihcwollatonoD
rotsrfidaehedilsnwodogotnerdlihcwollatonoD
run up slide.
WARNING – Safe Play Instructions
Orientate slide such that it gets the least amount of exposure
to the sun.
2

One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing
protective surfacing under and around your play equipment. The protective surfacing should be applied to a depth that is suitable
for the equipment height in accordance with ASTM F1292. There are different types of surfacing to choose from; whichever
product you select, follow these guidelines:
Loose-Fill Materials
• Maintain a minimum depth of 9 inches of loose-fill materials such as wood mulch/chips, engineered wood fiber (EWF), or
shredded/recycled rubber mulch for equipment up to 8 feet high; and 9 inches of sand or pea gravel for equipment up to 5 feet
high. NOTE: An initial fill level of 12 inches will compress to about a 9-inch depth of surfacing over time. The surfacing will also
compact, displace, and settle, and should be periodically raked and refilled to maintain at least a 9-inch depth.
• Use a minimum of 6 inches of protective surfacing for play equipment less than 4 feet in height. If maintained properly, this
should be adequate. (At depths less than 6 inches, the protective material is too easily displaced or compacted.)
NOTE: Do not install home playground equipment over concrete, asphalt, or any other hard surface. A fall onto a hard surface
can result in serious injury to the equipment user. Grass and dirt are not considered protective surfacing because wear and
environmental factors can reduce their shock absorbing effectiveness. Carpeting and thin mats are not adequate protective
surfacing. Ground level equipment -- such as a sandbox, activity wall, playhouse or other equipment that has no elevated play
surface -- does not need any protective surfacing.
• Use containment, such as digging out around the perimeter and/or lining the perimeter with landscape edging. Don’t forget to
account for water drainage.
• Periodically rake, check and maintain the depth of the loose-fill surfacing material. Marking the correct depth on the play
equipment support posts will help you to see when the material has settled and needs to be raked and or replenished. Be sure to
rake and evenly redistribute the surfacing in heavily used areas.
• Do not install loose fill surfacing over hard surfaces such as concrete or asphalt.
Poured-In-Place Surfaces or Pre-Manufactured Rubber Tiles
You may be interested in using surfacing other than loose-fill materials - like rubber tiles or poured-in-place surfaces.
• Installations of these surfaces generally require a professional and are not “do-it yourself” projects.
• Review surface specifications before purchasing this type of surfacing. Ask the installer/manufacturer for a report showing that
the product has been tested to the following safety standard: ASTM F1292 Standard Specification for Impact Attenuation of
Surfacing Materials within the Use Zone of Playground Equipment. This report should show the specific height for which the
surface is intended to protect against serious head injury. This height should be equal to or greater than the fall height - vertical
distance between a designated play surface (elevated surface for standing, sitting, or climbing) and the protective surfacing
below - of your play equipment.
• Check the protective surfacing frequently for wear.
Placement
Proper placement and maintenance of protective surfacing is essential. Refer to diagram on front cover. Be sure to;
• Extend surfacing at least 2m from the equipment in all directions.
• For to-fro swings, extend protective surfacing in front of and behind the swing to a distance equal to twice the height of the top bar
from which the swing is suspended.
• For tire swings, extend surfacing in a circle whose radius is equal to the height of the suspending chain or rope, plus 6 feet in all
directions.
From the CPSC Outdoor Home Playground Safety Handbook. At http://www.playgroundregs.com/resources/CPSC%20324.pdf
Protective Surfacing - Reducing Risk of Serious Head Injury From Falls.
2H 2H
H
Denotes Use Zone with Protective Surfacing
Use Zone for Single-Axis Swings
6 ft.
6 ft.
6 ft.
6 ft.
Denotes Use Zone with Protective Surfacing
Use Zone for Multi-Axis Swings
6 ft. 6 ft.
6 ft.
L
3

Instructions for Proper Maintenance
Your Cedar Summit Play System is designed and constructed of quality materials with your child’s safety in mind. As
with all outdoor products used by children, it will weather and wear. To maximize the enjoyment, safety and life of your
Play Set, it is important that you, the owner, properly maintain it.
HARDWARE:
Check metal parts for rust. If found,
sand and repaint using a non-lead paint
complying with 16 CFR 1303.
Inspect and tighten all hardware. On
wood assemblies DO NOT OVER-
TIGHTEN as to cause crushing and
splintering of wood.
Check for sharp edges or protruding screw threads, add
washers if required.
SHOCK ABSORBING SURFACING:
Check for foreign objects. Rake and check depth of loose
fill protective surfacing materials to prevent compaction and
maintain appropriate depth. Replace as necessary.
(See Protective Surfacing, page 3)
GROUND STAKES (ANCHORS):
Check for looseness, damage or deterioration. Should firmly
anchor unit to ground during use. Re-secure and or replace,
if necessary.
SWING HANGERS:
Check that bolts are secure and tight. Quick clips should be
completely closed and threaded clips screwed tight.
If squeaking occurs lubricate bushings with oil or WD-40®.
SWINGS, ROPES AND RIDES:
Reinstall if removed during cold season. Check all moving
parts including swing seats, ropes, chains and attachments
for wear, rust and other deterioration. Replace as needed.
Check that ropes are tight, secure at both ends and cannot
loop back as to create an entrapment.
WOOD PARTS:
Check all wood members for deterioration, structural
damage and splintering. Sand down splinters and replace
deteriorated wood members. As with all wood, some
checking and small cracks in grain is normal.
Applying a water repellent or stain (water-based) on a yearly
basis is important maintenance to maintain maximum life
and performance of the product.
Check the following at the beginning of the play season:
HARDWARE:
Inspect for tightness. Must be firmly against, but not
crushing the wood. DO NOT OVER-TIGHTEN.
This will cause splintering of wood.
Check for sharp edges or protruding screw threads.
Add washers if required.
SHOCK ABSORBING SURFACING:
Rake and check depth of loose fill protective surfacing
materials to prevent compaction and maintain appropriate
depth. Replace as necessary.
(See Protective Surfacing, page 3)
Check twice a month during play season:
SWING HANGERS:
Check that they are secure and orientated correctly. Hook
should rotate freely and perpendicular to support beam.
If squeaking occurs lubricate bushings with oil or WD-40®.
SWINGS AND RIDES:
Check swing seats, all ropes, chains and attachments for
fraying, wear, excessive corrosion or damage.
Replace if structurally damaged or deteriorated.
Check once a month during play season:
SWINGS AND RIDES:
To prolong their life, remove swings and store inside when
outside temperature is below 32°F/0°C. Below freezing,
plastic parts may become more brittle.
SHOCK ABSORBING SURFACING:
Rake and check depth of loose fill protective surfacing
materials to prevent compaction and maintain appropriate
depth. Replace as necessary.
(See Protective Surfacing, page 3)
Check at the end of the play season:
If you dispose of your play set: Please disassemble and dispose of your unit so that it does not create any unreasonable
hazards at the time it is discarded. Be sure to follow your local waste ordinances.
If Bolt protrudes
beyond T-Nut
Use an extra
flat washer
4

AboutOur Wood
Cedar Summit Premium Play Systems uses only premiumplayset lumber, ensuringthesafest product for your children’s
use. Although we take great care in selectingthebest quality lumber available, wood is still aproduct ofnature and susceptibleto
weatheringwhich can change the appearance of your set.
What causes weathering? Does itaffect the strength of my Play System?
Oneofthe main reasons for weatheringis the effects of water (moisture); the moisture content ofthe wood at thesurface is
different than theinterior ofthe wood. As the climate changes, moisture moves in or out ofthe wood, causingtension which can
result in checking and or warping. You can expect thefollowingdueto weathering. These changes will not affect thestrength of
theproduct:
1. Checking is surface cracks in the wood alongthe grain. A post (4” x 4”)will experience more checkingthan aboard (1” x 4”)
becausethesurface and interior moisture content will vary morewidely than in thinner wood.
2. Warping results from any distortion (twisting, cupping) fromtheoriginal plane oftheboard and often happens fromrapid
wetting and dryingofthe wood.
3. Fading happens as anatural change in the wood color as it is exposed to sun-light and will turn a grey over time.
How can I reduce the amount of weathering to my Play System?
At thefactory we have coated the wood with a water repellent or stain. This coatingdecreases the amount of water absorption
during rain orsnow thus decreasingthetension in the wood. Sunlight will break down the coating, applying a water repellant or
stain on a yearly basis is important maintenance. (see your local stain and paint supplier for arecommended product)
Most weathering is just the normal result of nature and will not affect safe play and enjoyment for your child. However if you are
concerned that a part has experienced a severe weathering problem please call our consumer relations department for further assistance.
warranty service.
province to province. This warranty excludes all consequential damages, however, some states do not allow the
limitation or exclusion of consequential damages, and therefore this limitation may not apply toyou.
10 Year Limited Warranty
Cedar Summit by KidKra warrants that this product is free fromdefect in materials and workmanship
for a periodof one year from the original date of purchase. In addition, lumber is warranted for 10
years against structural failure due to rot and insect damage. All other parts, such as hardware, swings,
rides, accessories, and slides carry aone-year warranty only.
This warranty appliesto the original owner and registrant and is non-transferable.
Regular maintenance is required to assure the integrity of your Play System. Failureby the owner
to maintain the product accordingto the maintenance requirements may void this warranty. This
warranty does not cover any inspectioncost.
This Limited Warranty does not cover:
•Labour for replacement of any defective item(s);
•Incidental or consequential damages;
• Cosmetic defects which do not affect performance or integrity;
• Vandalism; improper useor installation; acts of nature;
• Minor twisting, warping, checking, or any other natural occurring properties of wood that do not
affect performance or integrity.
Cedar Summit by KidKraft products have been designed for safety and quality. Any modifications
made to the original product could damage the structural integrity of the unit leading to failureand
possible injury. Cedar Summit by KidKraft cannot assume any responsibility for modified products.
Furthermore, modification voids any and all warranties.
This product is warranted for RESIDENTIAL USE ONLY. Under no circumstance should a Cedar Summit
by KidKra Play System beused in public settings such as schools, churches, playgrounds, parks, day cares
and the like. Such use may lead to product failure and potential injury. Any and all public usewill void this
warranty.
Cedar Summit by KidKraft disclaims all other representations and warranties of any kind, express or implied.
5

This identifies information that requires special
attention. Improper assembly could lead to an unsafe
or dangerous condition.
Where this is shown, 2 or 3 people
are required to safely complete the
step. To avoid injury or damage
to the assembly make sure to get
help!
Check that assembly is square
before tightening bolts.
Use a measuring tape to assure
proper location.
Check that set or assembly is properly level
before proceeding.
Pre-drill a pilot hole
before fastening screw
or lag to prevent
splitting of wood.
This indicates time to tighten bolts, but
not too tight! Do not crush the wood.
This may create splinters and cause
structural damage.
Part Identification Key
On each page, you will find the parts
and quantities required to complete the
assembly step illustrated on that page.
Here is a sample.
Key Number: The first two digits
represent the step number. The third
digit represents the piece. Note that if
the part is used in multiple steps then
the number only reflects the first step it
is used in.
Symbols
Throughout these instructions symbols are provided as important reminders for proper and safe assembly.
Proper Hardware Assembly
Lag screws require drilling pilot
holes to avoid splitting wood. Only
a flat washer is required. For ease of
installation liquid soap can be used
on all lag-type screws.
For bolts, tap T-Nut into hole with
hammer. Insert the hex bolt through
lock washer first then flat washer then
hole. Because the assemblies need to
be squared do not completely tighten
until instructed. Pay close attention to
diameter of the bolts. 5/16” is slightly
larger than 1/4”.
Note: Wafer head bolts with blue lock
tight or a bolt with a Ny-Lok nut do
NOT require a lock washer.
Once the assembly is tightened, watch for exposed threads.
If a thread protrudes from the T-Nut, remove
the bolt and add washers to eliminate this condition.
Extra washers have been provided for this purpose.
Use
Help
Use
Help
Measure
Distance
Square
Assembly
Use
Level
Pre-drill 1/8” & 3/16” Bit
Tighten
Bolts
CAUTION – Protrusion Hazard
Keys to Assembly Success
Tools Required
• Tape Measure
• Carpenters Level
• Carpenters Square
• Claw Hammer
• Standard or Cordless Drill
• #1 Phillips, #2 Robertson
and Screwdriver
• Ratchet with extension
(1/2” & 9/16” sockets)
• Open End Wrench
(1/2” & 9/16”)
• Adjustable Wrench
• 1/8” & 3/16” Drill Bits
• 3/16” Hex Key
• 8’ Step Ladder
• Safety Glasses
• Adult Helpers
• Pencil
Quantity Key Number Part Description,
Part Size
2X 012 Post 2 x 4 x 83”
No Yes
Lag Assembly
Bolt Assembly
Flat Washer
Lag Screw
Hex Bolt
Lock
Washer
Flat
Washer
Before mounting Lag
Screw, use factory drilled
holes as guides to drill 1/8”
pilot holes
T-Nut
(Hammer into place)
Do not crush wood!
If Bolt protrudes
beyond T-Nut
Use an extra
flat washer
6

Key Number: The rst two digits represent the step
number. The third digit represents the order in which
the part is listed in the step.
Note that if the part is used in multiple steps then
the key number only reects the rst step it is used in.
Part Quantity Key Number
Order Listed
(The order the part is
listed in step 1)
Part Description Part Size
2X 012 Post 2 x 4 x 83”
00
Your Key To Quick Assembly
SAVE TIME - TIP #1:
Wood parts are found in Box 2, 3, 4 & 5. Open each box with wood parts and
look for the Key Number stamped on the end of the wood part (see chart below).
Sort each wood part into the different assembly steps.
SAVE TIME - TIP #2:
In addition to the key number stamp, you can also identify the wood parts by
using the Parts Identication pages in the manual or the Parts Identication
weather resistant poster.
HARDWARE:
The majority of each hardware part comes packed in a separate bag so
you do not need to sort the hardware. Each assembly step indicates which
hardware (bolt, screw, washer etc.) you will require to complete the step.
SORTING WOOD PARTS INTO
EACH ASSEMBLY STEP WILL
SAVE TIME!
Step Step Step
01 2
Step Number
(This is Step 1)
.
7

441
2x
442 443
131
132
161
311
301
x4
571
570
223 224
2x
262
2x
413
2x
412
225
381
x2
411
x2
323
x2
324
x2
322
x2
227
222
2x
221
2x
371
063
072
060
341
x2
2x
081
(hidden)
295 294
2x
261
325
x2
391
x2
(hidden)
024
420 421 422 423
233
(hidden)
162
(Swing hidden)
Double Ride Maze N Wave Slide
Bell
Telescope w/ Mount
TNR 2 Slide LT Flange TNR 2 Slide RT Flange
9x TNR 2 Slide Elbow
TNR 4 Clamp Ring Set (10Pk)
Flat Panel Bracket Set (4Pk)
Sign
BBQ Lid
BBQ Base
Sink
BBQ Utensils
TNR 3 Short Exit
TNR 2 Slide Exit Top
Door Hardware
FRONT
Utensil Shelf x2
Fruit & Basket
Cooktop
Door Window
Front Roof Panel FSC
Narrow Front Panel FSC
End Panel FSC
Panel Front
Wall FSC
Panel FSC
061
End Half Wall FSC
055
052
054
051
053
420 421 422 423
252
8

151 021
022
x4
020
142
025
171
181
182
2x
183
191
172
071
062
041
044
x2
042
043
x3
023
231
030
030
032
032
032
033
033
033
033
033
141
031
331
2x
332
228
073
2x
082 112
2x
321
292
113
111
x18
271
291
x2
123
121
122
312
061
13x
414
251
(hidden)
226
x2
232
x2
(hidden)
Heavy "C" Bracket
Heavy "L" Bracket x3
Swing Belt Seat x2
Swing Rope x4
Spring Loaded
Quick Links x6
Acro Handle x2
Acro Bar
DX Swing Hanger (6Pk)
Heavy Flat Bracket x2
KK Playset
Plaque
Panel Corner Bracket (8Pk)
Rebar Ground
Stake (6Pk)
EN71 Hand Rail
Rocks (18Pk)
Corner Bracket (9Pk)
(hidden)
Narrow Angle
Bracket (3Pk)
(hidden)
2x MOD 5 Pane Window (2Pk)
TNR Tube Support
(hidden)
Acro Rope x2
2x Steel
Hand Grips
Flat Bracket (2Pk)
BACK
Plastic Formed Washers (18Pk)
TNR 4 Post Mount
(hidden)
Back Roof Panel FSC
Crow Ladder Grip
Swing Wall Panel FSC
Back Panel Narrow FSC
Wakll Back
Panel FSC
9

18pc. - 111 - 15.9 x 114.3 x 904.9mm - Floor Board FSC - Box 2 - 4819051
5/8 x 4-1/2 x 35-5/8"
13pc. - 414 - 15.9 x 85.7 x 827.1mm - Cedar Wall FSC - Box 3 - 4819308
5/8 x 3-3/8 x 32-9/16"
1pc. - 023 - 15.9 x 82.6 x 533.4mm - Ladder Gap FSC - Box 3 - 4818958
5/8 x 3-1/4 x 21"
1pc. - 025 - 15.9 x 82.6 x 1060.5 mm - RW-AL Support FSC - Box 3 - 4819263
5/8 x 3-1/4 x 41-3/4"
1pc. - 031 - 15.9 x 108 x 562mm - Access Board FSC - Box 3 - 4819032
5/8 x 4-1/4 x 22-1/8"
2pc. - 044 - 15.9 x 82.6 x 482.6mm - Nest Ladder Gap FSC - Box 3 - 4819234
5/8 x 4 x 36-3/8"
1pc. - 113 - 15.9 x 85.7 x 904.9mm - Floor Board FSC - Box 3 - 4819050
5/8 x 3-3/8 x 35-5/8"
1pc. - 271 - 15.9 x 114.3 x 904.9mm - Crowsnest Front Gap FSC - Box 3 - 4819291
5/8 x 4-1/2 x 35-5/8"
2pc. - 261 - 15.9 x 101.6 x 923.8 - Wall Board FSC - Box 2 - 4819313
1pc. - 451 - 15.9 x 85.7 x 285.8 mm - Bell Top FSC - Box 3 - 4609102
5/8 x 3-3/8 x 11-1/4"
1pc. - 453 - 15.9 x 85.7 x 285.8 mm - Bell Top RT FSC - Box 3 -
4609101
5/8 x 3-3/8 x 11-1/4"
1pc. - 292 - 15.9 x 82.5 x 971.5 - Crowsnest Floor Long Gap FSC - Box 3 - 4819315
5/8 x 3-1/4 x 38-1/4"
1pc. - 295 - 15.9 x 85.7 x 398.5mm - Short Floor FSC - Box 3 - 4819265
5/8 x 3-3/8 x 15-11/16"
1pc. - 294 - 15.9 x 85.7 x 398.5mm - Short Floor Gap FSC - Box 3 - 4819264
5/8 x 3-3/8 x 15-11/16"
2pc. - 291 - 15.9 x 114.3 x 971.5mm - Crowsnest Floor Long FSC - Box 3 - 4819314
5/8 x 4-1/2 x 38-1/4"
Actual Size
1½" x 1½"
1½" x 5⅜"
Nominal Size
2 x 2
2 x 6
Actual Size
1½" x 1½"
1⅜" x 2½"
1⅜" x 3⅜"
Nominal Size
2 x 2
2 x 3
2 x 4
Actual Size
1" x 3½"
1" x 4½"
1
" x 5½"
1⅜" x 2½"
Nominal Size
5/4 x 4
5/4 x 5
5/4 x 6
2 x 3
Nominal Size
1 x 5
1 x 6
5/4 x 2
5/4 x 3
5/4 x 4
Actual Size
⅝
" x 4½"
⅝
" x 5⅜"
1
" x 1⅜"
1" x 2½"
1" x 3½"
Actual Size
⅝
" x 3⅜"
⅝
" x 4½"
⅝
" x 5⅜"
Nominal Size
1 x 4
1 x 5
1 x 6
5/8 x 3-1/4 x 19"
Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size)
Nominal Size
½
x 4
1 x 2
1 x 3
1 x 4
Actual Size
7
16
" x 3¼"
⅝" x 1⅜"
⅝" x 2⅜"
⅝" x 3⅜"
10

4pc. - 022 - 23.8 x 82.6 x 495.3 mm - Tread FSC - Box 3 - 4818957
15/16 x 3-1/4 x 19-1/2"
3pc. - 032 - 15.9 x 133.4 x 562mm - Rock Board A FSC- Box 3 - 4818511
5pc. - 033 - 15.9 x 133.4 x 562mm - Board Rock B FSC - Box 3 - 4818512
5/8 x 5-1/4 x 22-1/8"
2pc. - 030 - 15.9 x 133.4 x 562mm - Access Rock Bottom FSC - Box 3 - 4818515
5/8 x 5-1/4 x 22-1/8"
5/8 x 5-1/4 x 22-1/8"
1pc. - 151 - 23.8 x 82.6 x 601.7mm - Support Diagonal FSC - Box 2 - 4819269
15/16 x 3-1/4 x 23-11/16"
1pc. - 141 - 23.8 x 82.6 x 362 mm - SW Ground FSC - Box 3 - 4812606
15/16 x 3-1/4 x 14-1/4"
3pc. - 043 - 23.8 x 82.6 x 444.5mm - Nest Tread FSC - Box 2 - 4819243
15/16 x 3-1/4 x 17-1/2"
1pc. - 132 - 23.8 x 108 x 1086.5mm - Table Top FSC - Box 2 - 4819324
15/16 x 4-1/4 x 42-3/4"
1pc. - 121 - 23.8 x 57.2 x 850.9mm - SW Wall Top FSC - Box 3 - 4819071
15/16 x 2-3/8 x 33-1/2"
1pc. - 122 - 23.8 x 57.2 x 990.6mm - Half Wall Top FSC - Box 2 - 4819131
15/16 x 2-1/4 x 39"
1pc. - 123 - 23.8 x 57.2 x 482.6mm - Small Half Wall Top FSC - Box 2 -
4819323
15/16 x 2-3/8 x 19"
2pc. - 325 - 23.8 x 76.2 x 489mm - Wall Tie FSC - Box 3 - 4819117
15/16 x 3 x 19-1/4"
1pc. - 233 - 23.8 x 133.4 x 889mm - Crowsnest Bottom Side Front FSC - Box 2 - 4819307
15/16 x 5-1/4 x 35"
2pc. - 411 - 23.8 x 63.5 x 857.3 - Crowsnest Top Side FSC - Box 2 - 4819309
15/16 x 2-1/2 x 33-3/4"
2pc. - 391 - 23.8 x 76.2 x 435mm - Short Wall Tie FSC - Box 2 - 4819266
15/16 x 3 x 17-1/8"
Actual Size
1½" x 1½"
1½" x 5⅜"
Nominal Size
2 x 2
2 x 6
Actual Size
1½" x 1½"
1⅜" x 2½"
1⅜" x 3⅜"
Nominal Size
2 x 2
2 x 3
2 x 4
Actual Size
1" x 3½"
1" x 4½"
1
" x 5½"
1⅜" x 2½"
Nominal Size
5/4 x 4
5/4 x 5
5/4 x 6
2 x 3
Nominal Size
1 x 5
1 x 6
5/4 x 2
5/4 x 3
5/4 x 4
Actual Size
⅝
" x 4½"
⅝
" x 5⅜"
1
" x 1⅜"
1" x 2½"
1" x 3½"
Actual Size
⅝
" x 3⅜"
⅝
" x 4½"
⅝
" x 5⅜"
Nominal Size
1 x 4
1 x 5
1 x 6
Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size)
Nominal Size
½
x 4
1 x 2
1 x 3
1 x 4
Actual Size
7
16
" x 3¼"
⅝" x 1⅜"
⅝" x 2⅜"
⅝" x 3⅜"
11

4pc. - 301 - 31.8 x 57.2 x 838.20mm - Roof Support FSC - Box 2 - 4609105
1-1/4 x 2-1/4 x 33"
2pc. - 332 - 31.8 x 63.5 x 419.1mm - Swing Side Upright FSC - Box 2 - 4819112
1-1/4 x 2-1/2 x 16-1/2"
1pc. - 231 - 23.8 x 133.4 x 889mm - Crowsnest Bottom Side Back FSC - Box 2 - 4819306
15/16 x 5-1/4 x 35"
1pc. - 225 - 31.8 x 63.5 x 971.5mm - Barrier Top End FSC - Box 2 - 4819305
1-1/4 x 2-1/2 x 38-1/4"
2pc. - 232 - 31.8 x 60.3 x 266.7mm - Wall Board Support FSC - Box 2 - 4819312
1-1/4 x 2-3/8 x 10-1/2"
2pc. - 226 - 31.8 x 63.5 x 311.2mm - Crowsnest Side Joist FSC - Box 3 - 4819298
1-1/4 x 2-1/2 x 12-1/4"
1pc. - 052 - 25.4 x 60.3 x 865mm - Front Wall Tie FSC - Box 2 - 4819302
1 x 2-3/8 x 34-1/16"
1pc. - 053 - 25.4 x 60.3 x 865mm - Back Wall Tie FSC - Box 1 - 4819303
1 x 2-3/8 x 34-1/16"
1pc. - 252 - 31.8 x 60.3 x 654mm - Nest Joist Center FSC - Box 2 - 4819295
1-1/4 x 2-3/8 x 25-3/4"
2pc. - 381 - 31.8 x 63.5 x 844.6mm - Wall Post FSC - Box 2 - 4819316
1-1/4 x 2-1/2 x 33-1/4"
2pc. - 413 - 31.8 x 60.3 x 340.8mm - Roof Tie FSC - Box 3 - 4819260
1-1/4 x 2-3/8 x 13-13/32"
2pc. - 412 - 31.8 x 60.3 x 170.5mm - Short Roof Tie FSC - Box 3 - 4819318
1-1/4 x 2-3/8 x 6-3/4"
1pc. - 051 - 31.8 x 60.3 x 857.3mm - Nest Joist Mid FSC - Box 2 - 4819297
1-1/4 x 2-3/8 x 33-3/4"
1pc. - 054 - 31.8 x 60.3 x 374.7mm - Nest Joist Back FSC - Box 3 - 4819294
1-1/4 x 2-3/8 x 14-3/4"
1pc. - 055 - 31.8 x 60.3 x 139.7mm - Ladder Joist Side FSC - Box 3 - 4819296
1-1/4 x 2-3/8 x 5-1/2"
1pc. - 421 - 25.4 x 31.8 x 887.2mm - Angle Wall B FSC - Box 2 - 4819321
1 x 1-1/4 x 34-15/16"
1pc. - 422 - 25.4 x 31.8 x 786.7mm - Angle Wall C FSC - Box 2 - 4819320
1 x 1-1/4 x 30-31/32"
1pc. - 423 - 25.4 x 31.8 x 686.2mm - Angle Wall D FSC - Box 2 - 4819319
1 x 1-1/4 x 27"
1pc. - 420 - 25.4 x 31.8 x 987.7mm - Angle Wall A FSC - Box 2 - 4819322
1 x 1-1/4 x 38-7/8"
1pc. - 162 - 25.4 x 63.5 x 254mm - Door Stop FSC - Box 2 - 4812715
1 x 2-1/2 x 10"
Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size)
12

2pc. - 081 - 31.8 x 76.2 x 1035.1mm - Floor Joist FSC - Box 3 - 4812608
1-1/4 x 3 x 40-3/4"
1pc. - 112 - 31.8 x 76.2 x 1606.6 - Long Floor Joist FSC - Box 2 - 4819056
1-1/4 x 3 x 63-1/4"
2pc. - 221 - 31.8 x 76.2 x 1816.1 - Crowsnest Post FSC - Box 3 - 4819304
1-1/4 x 3 x 71-1/2"
1pc. - 331 - 31.8 x 76.2 x 1187.5mm - Swing Top FSC - Box 3 - 4819113
1-1/4 x 3 x 46-3/4"
1pc. - 570 - 31.8 x 76.2 x 819.2mm - TNR Ground Brace FSC - Box 3 - 4818963
1-1/4 x 3 x 32-1/4"
1pc. - 571 - 31.8 x 76.2 x 514.4mm - TNR Upright FSC - Box 3 - 4818965
1-1/4 x 3 x 20-1/4"
1pc. - 142 - 31.8 x 76.2 x 558.8mm - Diagonal FSC - Box 3 - 4812607
1-1/4 x 3 x 22"
2pc. - 323 - 31.8 x 108 x 419.1mm - Left Upright FSC - Box 3 - 4819107
1-1/4 x 4-1/4 x 16-1/2"
2pc. - 322 - 31.8 x 76.2 x 419.1mm - Right Upright FSC - Box 3 - 4819110
1-1/4 x 3 x 16-1/2"
2pc. - 324 - 31.8 x 76.2 x 419.1mm - Center Upright FSC - Box 2 - 4819106
1-1/4 x 3 x 16-1/2"
1pc. - 222 - 31.8 x 79.4 x 971.5mm - Crowsnest Front FSC - Box 2 - 4819299
1-1/4 x 3-1/8 x 38-1/4"
1pc. - 227 - 31.8 x 88.9 x 418.5mm - Crowsnest Gusset Front FSC - Box 2 - 4819311
1-1/4 x 3-1/2 x 16-1/2"
1pc. - 228 - 31.8 x 88.9 x 391mm - Crowsnest Gusset Back FSC - Box 2 - 4819310
1-1/4 x 3-1/2 x 15-25/64"
1pc. - 251 - 31.8 x 76.2 x 311.2mm - Short Joist FSC - Box 3 - 4819326
1pc. - 223 - 31.8 x 123.7 x 971.5 - Crowsnest Slide Top FSC - Box 1 - 4819300
1-1/4 x 4-7/8 x 38-1/4"
2pc. - 371 - 31.8 x 76.2 x 138.7mm - Swing Top Small FSC - Box 3 - 4819270
1-1/4 x 3 x 5-15/32"
1-1/4 x 3 x 12-1/4"
2pc. - 321 - 31.8 x 63.5 x 1124mm - TB Support FSC - Box 2 - 4819114
1-1/4 x 2-1/2 x 44-1/4"
Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size)
Nominal Size
½
x 4
1 x 2
1 x 3
1 x 4
Actual Size
7
16
" x 3¼"
⅝" x 1⅜"
⅝" x 2⅜"
⅝" x 3⅜"
13

1pc. - 021 - 34.9 x 63.5 x 1468.8mm - Left Access FSC - Box 3 - 4819054 1-3/8 x 2-1/2 x 57-53/64"
1pc. - 020 - 34.9 x 63.5 x 1468.8mm - Right Access FSC - Box 3 - 4819055
1-3/8 x 2-1/2 x 57-53/64"
1pc. - 024 - 34.9 x 63.5 x 1468.8mm - Rock Rail FSC - Box 3 - 4819058
1-3/8 x 2-1/2 x 57-53/64"
2pc. - 082 - 38.1 x 38.1 x 1600 - Side Joist FSC - Box 1 - 4819064
1-1/2 x 1-1/2 x 63"
2pc. - 341 - 38.1 x 38.1 x 1409.7 - Wall Support FSC - Box 1 - 4819118
1-1/2 x 1-1/2 x 55-1/2"
1pc. - 042 - 34.9 x 63.5 x 1045.2mm - Nest Left Access FSC - Box 1 - 4819237
1-3/8 x 2-1/2 x 41-1/8"
1pc. - 041 - 34.9 x 63.5 x 1045.2mm - Nest Right Access FSC - Box 1 - 4819236
1-3/8 x 2-1/2 x 41-1/8"
1pc. - 131 - 38.1 x 38.1 x 1006.5mm - Table Support FSC - Box 3 - 4812612
1-1/2 x 1-1/2 x 39-5/8"
2pc. - 262 - 31.8 x 128 x 684.3mm - Crowsnest Front Spacer FSC - Box 2 - 4819293
1-1/4 x 5-1/32 x 26-15/16"
2pc. - 452 - 38.1 x 38.1 x 269.9mm - Bell Support FSC - Box 2 - 4609100
1-1/2 x 1-1/2 x 10-5/8"
1pc. - 224 - 31.8 x 139.8 x 971.5 - Crowsnest Bottom End FSC - Box 3 - 4819301
1-1/4 x 5-1/2 x 38-1/4"
1pc. - 171 - 76.2 x 133.4 x 2336.8 - Engineered SW Beam FSC - Box 1 - 4819049
3 x 5-1/4 x 92"
2pc. - 183 - 76.2 x 76.2 x 2336.8mm - SW Post FSC - Box 1 - 4819070
3 x 3 x 92"
1pc. - 191 - 63.5 x 76.2 x 1295.4 - Support Cross FSC - Box 1 - 4819067
2-1/2 x 3 x 51"
1pc. - 172 - 76.2 x 76.2 x 406.4 - SW Mount FSC - Box 3 - 4819069
3 x 3 x 16"
1pc. - 182 - 63.5 x 76.2 x 381 SW Block FSC - Box 3 - 4818507
2-1/2 x 3 x 15"
1pc. - 181 - 63.5 x 76.2 x 381 - SW Block Angle FSC - Box 3 - 4819068
2-1/2 x 3 x 15"
Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size)
14

2pc. - 0336 - 10 x 25.4 x 413.8 - Window Trim - Box 2 -
38033636
1pc. - 072 - 31.8 x 1092.2 x 2336.8mm
Panel Front Wall FSC - Box 2 - 47819135
1-1/4 x 43 x 92"
1pc. - 063 - 31.8 x 546.1 x 2336.8mm
Narrow Front Panel FSC - Box 2 - 47819144
1-1/4 x 21-1/2 x 92"
1pc. - 062 - 31.8 x 546.1 x 2336.8mm
Back Panel Narrow FSC - Box 2 - 47819193
1-1/4 x 21-1/2 x 92"
1pc. - 071 - 31.8 x 939.8 x 2336.8mm
SW Wall Panel FSC - Box 3 - 47819150
1-1/4 x 37 x 92"
1pc. - 073 - 31.8 x 1092.2 x 2336.8mm
Wall Back Panel FSC - Box 2 - 47819203
1-1/4 x 43 x 92"
1pc. - 060 - 31.8 x 939.8 x 2336.8mm
End Panel FSC - Box 3 - 47819200
1-1/4 x 37 x 92"
Actual Size
1½" x 1½"
1½" x 5⅜"
Nominal Size
2 x 2
2 x 6
Actual Size
1½" x 1½"
1⅜" x 2½"
1⅜" x 3⅜"
Nominal Size
2 x 2
2 x 3
2 x 4
Actual Size
1" x 3½"
1" x 4½"
1
" x 5½"
1⅜" x 2½"
Nominal Size
5/4 x 4
5/4 x 5
5/4 x 6
2 x 3
Nominal Size
1 x 5
1 x 6
5/4 x 2
5/4 x 3
5/4 x 4
Actual Size
⅝
" x 4½"
⅝
" x 5⅜"
1
" x 1⅜"
1" x 2½"
1" x 3½"
Actual Size
⅝
" x 3⅜"
⅝
" x 4½"
⅝
" x 5⅜"
Nominal Size
1 x 4
1 x 5
1 x 6
Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size)
Nominal Size
½
x 4
1 x 2
1 x 3
1 x 4
Actual Size
7
16
" x 3¼"
⅝" x 1⅜"
⅝" x 2⅜"
⅝" x 3⅜"
15

1pc. - 161 - 31.8 x 400.1 x 1070mm
Door Window Panel FSC - Box 2 - 47602837
1-1/4 x 15-3/4 x 42-1/8"
1pc. - 061 - 31.8 x 514.4 x 809.6mm
End Half Wall FSC - Box 3 - 47819201
1-1/4 x 20-1/4 x 31-7/8"
1pc. - 312 - 31.8 x 819.2 x 1143 mm
Back Roof Panel FSC - Box 3 - 47609124
1-1/4 x 32-1/4 x 45"
1pc. - 311 - 31.8 x 825.5 x 1143 mm
Front Roof Panel FSC - Box 3 - 47609082
1-1/4 x 32-1/2 x 45"
1x - TNR 2 Slide Lt Flange
(3310122)
1x - TNR 2 Slide Rt Flange
(3310123)
9x - TNR 2 Slide Elbow
(3310121)
1x - TNR 4 Clamp Ring Set
(3300130) (10 Pk)
1x - TNR 2 Slide Exit Top
(3310124)
1x - TNR3 Short Exit
(3310132)
Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size)
16

1x - Rocks (8pk) (3320013)
1x - Telescope w/ Mount
(3320161)
1x - Quadrex Driver
(9200015)
2x - Steel Hand Grip
(9200211) -Yellow
1x - Steering Wheel
(3320255)
1x - Plastic Formed
Washer (18 Pk)
(3290000)
1x - Flat Panel Bracket
(4 Pk)(3205941
1x - Playset Bracket Set (3205955)
1x - Acro Bar
(9200131)
1x - Rebar Ground
Stake (6 Pk)
(3200318)
1x - DX Swing Hangers
with Quick Links (6 Pk)
(3201950)
1x - Corner
Bracket (3 Pk)
(3205973)
1x - Narrow Angle
Bracket (3 Pk)
(3205940)
1x - #2 x 2"
Robertson Driver
(9200014)
3x - Heavy L-Bracket
(9200151)
1x - Heavy Bracket Set
(3205701)
1x - Crimp Rope Bag (3502045)
2x Acro Rope EN71
4x Swing Rope w/ Crimps
2x 9207712
Door Hinge
9207713
Door Catch
2x 9207711
Door Handle
1x Magnetic Catch
1x Catch Plate
1x - Door Hardware (3200710)
1x - TNR3 Tube Support
(9200158)
1x - Heavy C-Bracket
(9200153)
2x - Heavy Flat Bracket
(9200149)
1x - Corner Panel
Bracket (6 Pk)
(3205977)
1x - Quick Links w.
Thread (2pk)
(3200022)
1x - BBQ Deluxe Kitchen
Set (3330008)
1x - BBQ Lid
9327812
1x
- Basket with
Fruit 3330015
2x - Utensil Shelf
9321691
1x - Sign
9331614
1x - Bell with Horseshoe
(3200309)
1x - Flat Bracket (2 Pk)
(3205960)
1x - BBQ Sink Set
3332608
1x
- BBQ Utensils
3331610
1x
- EN71 Hand Rail (3200224) -Yellow
1x
- Double Ride Maze N Wave Slide (3318125)
31x - Square Nylok Nut
(54902200)
2x - TNR 4 Post Mount
Clamp
(9200157)
1x - TNR 4 Post Mount
Base
(9200156)
1x - 1/4 x 14.5mm Pan
Head Bolt
(53452209)
30x - 1/4 x 12.7mm Pan
Head Bolt
(53453202)
2x
- MOD 5 Pane Window
(2Pk) (3330502)
1x - Cedar
Summit/KidKraft
Plaque
(9320358)
1x - Crow Ladder
Grip
(9200235)
2x - Swing Belt Seat
(9320130)
2x - Acro Handle
(9200131)
1x - Flange Mount
(2pk) (3325996)
1x
- 3/8" Drill Bit
1x
- 1/8" Drill Bit
1x - KK Playset
Plaque
(9320370)
1x - TNR 4 Post Mount
(3200155)
Part Identification (Reduced Part Size)
1x - BBQ Cooktop 3332609
1x - BBQ Base
3331611
17

(118) S3 - Wood Screw
#8 x 2-1/2"
- (52043522)
(22) S4 - Wood Screw
#8 x 3"
- (52043530)
(29) S7 - Pan Screw
#12 x 2"
- (52433620)
(19) S6 - Pan Screw
#12 x 1"
- (52433610)
(3) S10 - Pan Screw
#8 x 1"
- (52433510)
(246) S20 - Wood Screw
#8 x 1-3/8"
- (52043516)
(66) S0 - Truss Screw
#8 x 7/8"
- (52933505)
(10) LW2 - 5/16" Lock Washer - (51303300)
(18) LN2 - 5/16" Lock Nut
-
(54303300)
(25) TN2 - 5/16" T- Nut
-
(54503300)
(17) BN1 - 1/4" Barrel Nut
-
(54803200)
(40) TN1 - 1/4" T - Nut
-
(54503200)
(58) LW1 - 1/4" Lock Washer - (51303200)
(66) FW2 - 5/16" Flat Washer - (51103300)
(52) FW1 - 1/4" Flat Washer - (51103200)
(34) S8 - Pan Screw
#12 x 3/4"
- (52433603)
(12) PB6 - Pan Bolt
1/4 x 1"
- (53413210)
(67) LN1 -
1/4 Lock Nut
- (54303200)
(8) FW6 - #12 Screw Bezel - (9299500)
(17) PB2 - Pan Bolt
1/4 x 1-1/4"
- (53433212)
(14) FW10 - 3/8" Flat Washer - (51103800)
(7) LN3 -
3/8 Lock Nut
- (54303800)
(56) PB1 - Pan Bolt
1/4 x 3/4"
- (53453203)
(32) S37 - Pan Screw
#7 x 5/8"
- (52433009)
(9) S38 - Pan Screw
#7 x 1-1/8"
- (52433014)
(88) S11 - Wood Screw
#8 x 2"
- (52043520)
(9) S2 - Wood Screw
#8 x 1-1/2"
- (52043512)
(18) FW0 - 3/16" Flat Washer -
(51103100)
(10)
S40
- Truss Screw
#6 x 3/4"
- (52933903)
Hardware Identification (Actual Size)
18

(1) H8 -
Hex Bolt 1/4 x 4-1/4"
- (53703241)
(2) G5 -
Hex Bolt 5/16 x 4-1/2"
- (53703342)
(1) LS1 - Lag Screw
1/4 x 1-1/2"
- (52213212)
(8) H1 -
Hex Bolt 1/4 x 1-1/2"
- (53703212)
(2) H3 -
Hex Bolt 1/4 x 2-1/2"
- (53703222)
(6) H9 -
Hex Bolt 1/4 x 1-1/4"
(53703211)
(6) H10 -
Hex Bolt 1/4 x 2-1/4"
- (53703221)
(10) H12 -
Hex Bolt 1/4 x 3"
- (53703230)
(19) WL5 - Wafer Lag
1/4 x 2-1/2"
- (52613222)
(8) WL3 - Wafer Lag
1/4 x 1-3/8"
(52613216)
(5) LS9 - Lag Screw
5/16 x 4-3/4"
- (52213343)
(6) WB9 -
Wafe
r
Bolt 5/16 x 2-1/8"
- (53613324)
(2) WB8 -
Wafer Bolt 5/16 x 2-3/8"
- (53613326)
(7) WB7 -
Wafer Bolt 5/16 x 3"
- (53613330)
(6) G21 -
Hex Bolt 5/16 x 3-3/4"
- (53703333)
(12) G13 -
Hex Bolt 5/16 x 6-1/8"
- (53703364)
(6) WB10 -
Wafer Bolt 5/16 x 2-5/8"
- (53613329)
(1) G26 -
Hex Bolt 3/8 x 9-1/4"
- (53703891)
(4) G17 -
Hex Bolt 3/8 x 6"
- (53703860)
(1) G20 -
Hex Bolt 3/8 x 4"
- (53703840)
(5) H2 -
Hex Bolt 1/4 x 2"
- (53703220)
Hardware Identification (Actual Size)
19

B. If there are any missing or damaged pieces or you need assistance with
assembly please contact the consumer relations department directly. Call us
before going back to the store.
STOP STOPSTOP STOP
Key Number: The rst two digits represent the step
number. The third digit represents the piece. Note
that if the part is used in multiple steps then the
number only reects the rst step it is used in.
Quantity Key Number Part Description,
Part Size
2X 012 Post 2 x 4 x 83”
Step 1: Inventory Parts - Read This Before Starting Assembly
• Please refer to Page 6 for proper hardware assembly.
• Each step indicates which bolts and/or screws you will need for assembly, as well as
any at washers, lock washers, t-nuts or lock nuts.
A. This is the time for you to inventory all your hardware, wood and accessories,
referencing the parts identication sheets. This will assist you with your assembly.
• The wood pieces will have the key number stamped on the ends of the boards.
Organize the wood pieces by step, as per the key numbering system below.
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 4)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 5)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 6)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 1)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 2)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 3)
MODEL NUMBER: F29055E
TRACKING NUMBER (from ID Plaque):
[email protected]
Online Parts Replacement:
Cedarsummitplay.com/parts-center-
warranty-claim
Customer Service:
1(800) 933-0771 or [phone]
Europe Customer Service: [phone]
[email protected]
EU Online Parts Replacement: parts.kidkraft.eu
C. Read the assembly manual completely, paying special attention to EN71 and
ASTM warnings; notes; and safety/maintenance information on pages 1 - 6.
D. Before you discard your cartons ll out the form below.
• The carton I.D. stamp is located on the end of each carton. The tracking number is
located on the Cedar Summit ID Plaque (9320370).
• Please retain this information for future reference. You will need this information if you
contact the Consumer Relations Department.
20