Inter-fab X-STREAM 2 SLIDE Programming manual

XS2-IM R v. 10/14 (SBK-XS2 INSTALL)
3 0 5 0 S . A L V E R N O N W A Y • T U C S O N , A Z 8 5 7 1 3
520.790.7040 • 800.737.5386 • FAX [phone]
i n t e r - f a b . c o m
X - S T R E A M 2 ™S L I D E
Assembly & Installation Instru tions
IMPORTANT
THESE INSTRUCTIONS
MUST REMAIN WITH
THE SLIDE OWNER!

I N S T A L L A T I O N M A N U A L X - S T R E A M 2 ™ S L I D E
1
XS2-IM R v. 10/14 (SBK-XS2 INSTALL)
TABLE OF CONTENTS:
Important Notic s to th Install r..............................................2
Int nd d Us Instructions ........................................................3
Wat r Saf ty Env lop .............................................................4
Slid Plac m nt & Footprint Diagrams - L ft Turn .......................5
Slid Plac m nt & Footprint Diagrams - Right Turn......................6
Slid Compon nts ...................................................................7
R quir d Tools........................................................................8
St p 1: Attach St p Ass mbly to Entry S ction...........................9
St p 2: Attach Handrails to Ladd r ......................................9-11
St p 3: Attach F t to L gs...................................................12
St p 4: Ass mbl th Flum S ctions......................................13
St p 5: Alignm nt of Flum S ctions .......................................13
St p 6: Attach L gs to Flum .................................................13
St p 7: Attach Entry S ction & Ladd r to Flum .......................14
St p 8: Anchor Slid to D ck .................................................15
St p 9: Conn ct Wat r Supply Syst m ....................................15
St p 10: Finishing St ps........................................................16
Final Insp ction Ch ck List .....................................................16
Slid Car & Maint nanc ......................................................16
Pav r Kit Information.............................................................17
Explod d Vi w of X-Str am 2 Slid ..........................................18
Parts List (corr sponds with xplod d vi w)..............................19
Hardwar Kit Information.......................................................20
Not s..................................................................................21
Int r-Fab Limit d Warranty.....................................................22

I N S T A L L A T I O N M A N U A L X - S T R E A M 2 ™ S L I D E
2
XS2-IM R v. 10/14 (SBK-XS2 INSTALL)
THE X-STREAM 2 SLIDE CAN BE ASSEMBLED AND INSTALLED IN EITHER A LEFT
OR RIGHT TURN CONFIGURATION.
INTER-FAB HIGHLY RECOMMENDS THAT YOU READ THE ENTIRE INSTALLATION
MANUAL BEFORE YOU ATTEMPT THE INSTALLATION OF THE X-STREAM 2 SLIDE.
YOU MUST USE THE PROVIDED ANTI-SEIZE ON ALL THE BOLTS AND ALL-THREADS
OR THE NUTS MAY SEIZE.
INTER-FAB RECOMMENDS THAT A TWO-PERSON CREW ASSEMBLE THE X-STREAM
2 SLIDE.
INTER-FAB HIGHLY RECOMMENDS THAT YOU FOLLOW THE INSTALLATION
SEQUENCE IN THIS MANUAL.
THE SLIDE POSITIONING GRAPHICS ON PAGES 5 AND 6 ARE FOR REFERENCE
ONLY. INTER-FAB STRONGLY RECOMMENDS THAT ONLY THE FULLY AND
CORRECTLY ASSEMBLED SLIDE BE USED TO LOCATE THE POSITIONS FOR THE
ANCHOR BOLTS AS DESCRIBED ON PAGE 15.
IMPORTANT NOTICES TO THE INSTALLER

I N S T A L L A T I O N M A N U A L X - S T R E A M 2 ™ S L I D E
3
XS2-IM R v. 10/14 (SBK-XS2 INSTALL)
INTENDED USE INSTRUCTIONS
1. Ev ryon who us s this slid must know, und rstand and follow th s instructions
2. Th ANSI/APSP/ICC-5 2011 standard for abov ground pools prohibits th us of slid s or diving boards
on abov ground pools.
3. This slide is designed for residential inground pool use ONLY. This slide may not be used on any
above ground pool. Su h use of this slide may result in serious injury or death.
4. This slid should n v r b install d on abov ground pools, ponds, floating docks or platforms, boat docks
or hous boats or any natural body of wat r.
5. This slid should n v r b install d on any comm rcial, public or s mi-public pool.
6. B familiar with th shap and d pth of th pool b for you slid . This slid should only b us d with th
prop r wat r saf ty nv lop , as d scrib d in Diagrams A, B & C on pag 4 and in accordanc with th
slid positioning Diagrams D, E, F and G on pag s 5 and 6.
7. B caus th slid may only b us d in wat r 4’ d p or gr at r, all slid us rs must b abl to swim in
d p wat r.
8. W ight limit for this slid is 250 pounds, no slid r w ighing mor than 250 pounds may us this slid .
9. Th surfac of th slid is v ry slipp ry wh n w t; USE CAUTION wh n nt ring th slid and wh n
transitioning from standing to sitting.
10. Slid in a f t first sitting position ONLY.
11. IMPORTANT: sliding h adfirst is prohibit d: s rious spinal injury r sulting in paralysis or d ath can r sult.
12. Maintain adult sup rvision at all tim s.
13. Only on p rson at a tim is allow d on th slid ; this includ s th ladd r.
14. B sur th wat r d liv ry syst m is on and lubricating th slid prior to us .
15. Collision with anoth r swimm r or a div r can r sult in s rious injury or d ath for on or both p rsons:
B for sliding, always mak sur that th path in front of th slid is fr from any (including subm rg d)
obstructions including oth r p opl or obj cts in th pool such as rafts, inn r tub s tc. Wh n a diving
board is also pr s nt, mak sur you do not us th slid whil som on is on or using a diving board.
Tak turns.
16. No roughhousing or hors play should b allow d on th slid at any tim .
17. Do not stand, jump or div from any part of th slid .
18. Do not slid on obj cts such as rafts or inn r tub s. doing so gr atly incr as s your risk of injury.
19. Do not slid through or at obj cts such as rafts or inn r tub s, doing so gr atly incr as s your risk of
injury.
20. Do not us this slid if physically impair d or handicapp d without your doctor’s p rmission.
21. Do not us this slid with a history of h art conditions, s izur s, back probl ms, fainting or f ar of
h ights.
22. Do NOT us this slid if you ar pr gnant.
23. Do not drink alcohol and us this slid .
24. Don’t tak chanc s, insp ct th slid at l ast onc a y ar (s th slid insp ction list on pag 16, do
not us th slid if any part b com s loos , damag d, w ak n d or brok n. If n c ssary, b for using
th slid again, hav it insp ct d and r pair d by a comp t nt prof ssional familiar with pool slid s.
SLIDE IN A SITTING
POSITION ONLY
Fac forward on th slid , holding th l gs and arms
with th palms of your hands forward and tilt d up.
WARNING: SERIOUS INJURY OR DEATH CAN RESULT FROM THE
IMPROPER INSTALLATION OR USE OF THIS SLIDE.
When installed a ording to these instru tions, this slide onforms to
Consumer Produ t Safety Standard Guidelines.
DO NOT SLIDE HEAD FIRST SERIOUS INJURY
CAN RESULT DEEP WATER SWIMMERS
ONLY

I N S T A L L A T I O N M A N U A L X - S T R E A M 2 ™ S L I D E
4
XS2-IM R v. 10/14 (SBK-XS2 INSTALL)
DIAGRAM A
(NOT TO SCALE)
DIAGRAM C
(NOT TO SCALE)
Minimum Wat r Saf ty Env lop
3'
4'6"9'
4'
Point A
4'
WATER SAFETY ENVELOPE:
A minimum wat r d pth of thr f t (3') und r th xit
of th slid which incr as s to a d pth of four f t (4')
at point A which is locat d four f t six inch s (4'6")
from th back wall of th pool. A minimum d pth of
four f t (4') must b maintain d at a distanc of nin
f t (9') along th c nt rlin of th slid from point A.
Th abov d scrib d wat r d pth profil shall xt nd a
minimum of thr f t thr inch s (3'3") on ith r
sid of th c nt rlin of th slid .
(S Diagrams A, B & C)
13'6"
16˚
20" Max
Level Deck
Water Level
DIAGRAM B
(NOT TO SCALE)
Minimum Slid
Cl aranc Ar a
ALL SLIDES SHOULD
BE GROUNDED
Ch ck your local l ctrical
cod r quir m nts.
X-STREAM 2

I N S T A L L A T I O N M A N U A L X - S T R E A M 2 ™ S L I D E
5
XS2-IM R v. 10/14 (SBK-XS2 INSTALL)
SLIDE PLACEMENT DIAGRAM & FOOTPRINT DIAGRAM
X-Stream 2 S ide - Left Turn
DIAGRAM D
(NOT TO SCALE)
DIAGRAM E
(NOT TO SCALE)

I N S T A L L A T I O N M A N U A L X - S T R E A M 2 ™ S L I D E
6
XS2-IM R v. 10/14 (SBK-XS2 INSTALL)
SLIDE PLACEMENT DIAGRAM & FOOTPRINT DIAGRAM
X-Stream 2 S ide - Right Turn
DIAGRAM F
(NOT TO SCALE)
DIAGRAM G
(NOT TO SCALE)

I N S T A L L A T I O N M A N U A L X - S T R E A M 2 ™ S L I D E
7
XS2-IM R v. 10/14 (SBK-XS2 INSTALL)
IMPORTANT: For a L ft Turn Slid , Flum A–B is upp r flum , and C–D is th low r flum ,
in that ord r. For a Right Turn Slid , C–D is th upp r flum and A–B is th low r flum .
Flum s ar lab l d A–B or C–D in small l tt rs c nt r d on flang s.
A–B Flume C–D Flume
Exit Se tion Entry Se tion Straight Foot
Pedestal (2)
Step Assembly Long Leg Short Leg
Handrail (2)
1–Right; 1–Left Water Outlet ( omes with entry se tion)
X-STREAM 2 SLIDE COMPONENTS

I N S T A L L A T I O N M A N U A L X - S T R E A M 2 ™ S L I D E
8
XS2-IM R v. 10/14 (SBK-XS2 INSTALL)
LIST OF REQUIRED TOOLS
Tools required for assembly and installation of X-Stream 2 slide:
NOTE: USE PROVIDED ANTI-SEIZE ON ALL BOLTS!
1. Hammer
2. 3/8" drive rat het
3. 3/8" x 6" rat het extension
4. 1/2" deep so ket (deep so ket is ne essary)
5. 9/16" so ket
6. 9/16" box end rat het wren h
7. Drill with 3/8" masonry bit
8. Tape measure
9. PVC Pipe Cutter
ASSEMBLY AND INSTALLATION INSTRUCTIONS
For l ft turn slid s, flum A–B is th upp r flum and C–D is th low r flum , in that ord r.
For right turn slid s, flum C–D is th upp r flum and A–B is th low r.
Fig. 1
Note: Use slide box and pa kaging during assembly to prote t slide omponents from
damage from the de king surfa e.

9
XS2-IM R v. 10/14 (SBK-XS2 INSTALL)
2” 2 1/2”
I N S T A L L A T I O N M A N U A L X - S T R E A M 2 ™ S L I D E
STEP ONE: Attach the Step Assemb y to the Entry Section
Thr ad th fl x PVC hos from th ntry s ction through th st p tub ass mbly and out
th pr -drill d hol abov th bottom st p. (See Fig. 1) Utilizing hardwar kit XS-103-SS,
attach th st p ass mbly to th ntry s ction on th ground. B car ful not to scratch th
slid ; us th cardboard box th slid arriv d in for prot ction. Ins rt th top of th ladd r
into th ladd r r c iv r on th ntry s ction and align th hol s. (See Fig. 2) Plac a 3/8”
flat wash r ov r a 3/8” x 7-1/2” bolt; th n 3/8” flat wash r th n push bolt through th
pr -drill d hol s in th PVC st p ass mbly all th way through and out th opposit sid . Hand
tight n only. (Th s will b tight n d aft r attachm nt to flum / xit s ction.
Fig. 2: Ladder Step Support Sub-Assembly
STEP TWO: Attach the Handrai s to the Ladder and Entry Section
TIP: Install th handrails as shown in figur b low.
TIP: Hand tight n th all-thr ads into th handrails only, do not us any m chanical m ans
such as a wr nch or pli rs to tight n th all-thr ads.
TIP: Th r ar 7 all-thr ads utiliz d on ach handrail. Th r ar 2 diff r nt l ngths of all-
thr ads us d on ach handrail. (See Fig. 3 to match actual siz .) (XS2-105-SS Kit)
TIP: Th offs t at th bottom of ach handrail fac s in as th st p attachm nt point is nar-
row r than th ntry s ction.
Fig. 3 Fig. 4: Ba k View of Ladder Se tion Assembly

I N S T A L L A T I O N M A N U A L X - S T R E A M 2 ™ S L I D E
10
XS2-IM R v. 10/14 (SBK-XS2 INSTALL)
STEP TWO: Attach the Handrai s to the Ladder and Entry Section - CONT.
Ins rt th corr ct l ngth of all-thr ad into th nuts mb dd d in th handrails th n attach
th handrails as illustrat d. (See Fig. 5 and 6)
Hand tight n all-thr ad into ach of th 7
locations on th handrails. Ensur corr ct
l ngth of all-thr ad is us d at ach location.
5/16” x 2” all-thr ad (5 ach as shown)
5/16” x 2-1/2” all-thr ad (2 ach as shown)
Make sure to use provided anti-seize on
the all-thread before inserting into the
embedded nuts.
Ins rt handrail into th top s ction first as
illustrat d. Push or pull th handrail apart
until th all-thr ads pass through th 5
hol s in th ntry s ction and through th
hol s drill d in th upp r 2 st ps.
Make sure to use the provided anti-seize
on the flange nut threads before atta hing
to the all-thread.
2-1/2”x5/16”
2”x5/16”
Fig. 5
Fig. 6
Fig. 6

I N S T A L L A T I O N M A N U A L X - S T R E A M 2 ™ S L I D E
11
XS2-IM R v. 10/14 (SBK-XS2 INSTALL)
Th s 5 locations on th ntry s ction r c iv
a flang nut only. A flat wash r is not n d d.
Hand tight n.
Make sure to use the provided lubri ant
on the all-threads before atta hing the
flange nuts.
Th s two locations r quir a flat wash r,
flang nut and rubb r cap. Hand tight n.
Make sure to use the provided lubri ant
on the all-threads before atta hing the
flange nuts.
NOTE: 1/8” – 1/4” of the all-threads will
extend through the flange nut.
Now tight n all 7 nuts on ach handrail and
r p at for oth r handrail.
Don’t forg t th prot ctiv rubb r caps.
(Back of st ps only.)
Fig. 7
Fig. 8
Fig. 8
STEP TWO: Attach the Handrai s to the Ladder and Entry Section - CONT.

I N S T A L L A T I O N M A N U A L X - S T R E A M 2 ™ S L I D E
12
XS2-IM R v. 10/14 (SBK-XS2 INSTALL)
STEP THREE: Attach the Foot Pedesta s to the Legs
TIP: Both PVC l gs hav a diff r nt hol drill patt rn at ach nd. Th r is a top/bottom
ori ntation. Th offs t bolt hol s go to th top and bolt to th flum s. (See Fig. 9)
Ins rt on nd of th long PVC l g onto th foot p d stal, align th hol s, utilizing hardwar kit
XS-101-SS, plac a flat wash r ov r a 3/8” bolt; th n push bolt through th pr -drill d hol s
in th PVC l g and th foot p d stal, th n plac flat wash r th n 3/8” nylon nut and tight-
n. R p at th proc ss for th short PVC l g.
STEP FOUR: Assemb e the F ume Sections
TIP: Ass mbl th flum s ctions on th ground. B car ful not to scratch th slid ; us
th cardboard box for prot ction. Hand tight n th flum bolts for now, th y will b fully
tight n d onc th flum is corr ctly align d.
Right Turn or Left Turn Assembly:
Th flum s ar lab l d A–B or C–D in small l tt rs on th flang s without th gask ts.
To ass mbl a Left Turn slid : flum A–B will b th upp r flum and C–D will b th low r
flum , ass mbl d in that ord r.
To ass mbl a Right Turn slid : flum C–D will b th upp r flum and A–B will b th low r
flum , ass mbl d in that ord r.
TIP: Th r ar 3 factory install d gask ts. Ensur that a gask t is in plac on th ntry
s ction, and th “B” nd of th A–B flum and th “D” nd of th C–D flum .
Utilizing hardwar kit XS2-102-SS, attach th low r flum to th upp r flum . Align th fiv
hol s in th flang , push 3/8” bolt through a flat wash r, th n through th pr -drill d hol s
in th flang s, th n push bolt through a flat wash r, th n a lock wash r and through a 3/8”
nut. Hand tight n at this tim .
Fig. 9

I N S T A L L A T I O N M A N U A L X - S T R E A M 2 ™ S L I D E
13
XS2-IM R v. 10/14 (SBK-XS2 INSTALL)
STEP FOUR: Assemb e the F ume Sections – CONT.
Utilizing hardwar kit XS2-102-SS, attach th xit s ction to th low r flum s ction. Align
th fiv hol s in th flang , push 3/8” bolt through a flat wash r, th n through th pr -drill d
hol s in th flang s, th n push bolt through a flat wash r, th n a lock wash r and through
a 3/8” nut. Hand tight n at this tim .
STEP FIVE: A ignment of F ume Sections
Th r is nough tol ranc in th flang conn ctions to provid a smooth and v n transition
of th sliding surfac b tw n th flum s ctions.
Onc th two flum s ctions and th xit s ction ar bolt d tog th r hand tight, th n g ntly
push or pull on th flum s ctions to nsur a smooth v n alignm nt of th sliding surfac .
N xt, starting with th xit s ction, tight n th c nt r bolts first and th n tight n th two
out r bolts maintaining a smooth sliding surfac .
R p at this proc ss on th flang b tw n th upp r and low r flum .
Fig. 10
STEP SIX: Attach the Legs to the F ume
Ins rt th top of th long l g into l g r c iv r of th upp r flum , and th top of th short
l g into th l g r c iv r of th low r flum . Alight hol s, th n utilizing hardwar kit XS-103-
SS, plac a 3/8” Flat Wash r ov r a 3/8 x 7 ½” Bolt and push th bolt through th pr -
drill d hol s in th PVC l g all th way through and out th opposit sid . Plac a 3/8” Flat
Wash r th n a 3/8” Lock Wash r follow d by a 3/8” H x Nut and hand tight n only. R p at
with a s cond 7 ½” bolt to s cur th l gs to th flum s ctions, hand tight n only.
NOTE: Push the 7 ½” Bo ts through the parts in the direction that the Bo t Heads
face away from the poo as i ustrated in Figure 11.2.
Fig. 11: Flumes/Exit Assembly Fig. 11.2

I N S T A L L A T I O N M A N U A L X - S T R E A M 2 ™ S L I D E
14
XS2-IM R v. 10/14 (SBK-XS2 INSTALL)
TIP: Hand tight n th all-thr ads into th
ntry s ction flang only. Do not us any
m chanical m ans such as a wr nch or
pli rs to tight n th all-thr ads.
With two p opl , stand th ass mbl d
Flum s/Exit Ass mbly upright and balanc
on th two l gs. L an th Ladd r & Entry
S ction against th Upp r Flum S ction.
Align th 5 all-thr ads in th ntry s ction
with th 5 hol s in th Upp r Flum S ction
and g ntly push th m through. Plac a 3/8”
flat wash r, th n lock wash r and th n a
3/8” nut on ach all-thr ad. Ensur a smooth
v n alignm nt of th sliding surfac and
tight n th nuts in an alt rnating patt rn
until all th nuts ar uniformly tight.
Do not over tighten.
STEP SEVEN: Attach the Entry Section & Ladder to the F ume
Utilizing hardwar kit XS2-102-SS, thr ad th (5) 3/8” x 2.5” all-thr ads into th mb dd d
nuts in th ntry s ction flang . Th all-thr ads will thr ad in about 3/4” with approximat -
ly 1-3/4” protruding. (See Fig. 12)
Fig. 12
Fig. 13

I N S T A L L A T I O N M A N U A L X - S T R E A M 2 ™ S L I D E
15
XS2-IM R v. 10/14 (SBK-XS2 INSTALL)
STEP EIGHT: Anchoring the S ide to the Deck
Position th ass mbl d slid on th d ck in its corr ct and final position, th n nsur that
th long and short l gs ar plumb by ch cking ach l g with a bubbl l v l on two sid s at
90˚ to ach oth r. Th n utilizing a slop find r, nsur that th Ladd r is at a 16˚ slop from
v rtical as shown in Diagram C on pag 4. Onc th l gs and ladd r ar corr ctly ori nt d,
tight n th 4 bolts on ach upp r PVC l g and st p ass mbly (12 bolts total).
N xt, r ch ck th alignm nt of th sliding surfac , if n c ssary, loos n th flum nuts and
g ntly adjust for a smooth, v n sliding surfac . Onc align d corr ctly, r -tight n th flang
nuts in an alt rnating patt rn until th nuts ar uniformly tight n d and th flum gask ts
ar fully compr ss d. Do not over tighten.
Now that th slid is in its corr ct and final position, th 2 l gs ar plumb, and th ladd r
is at 16˚ slop , us th f t as a t mplat to car fully mark th locations for all th anchor
bolts. Sinc it is not possibl to drill th anchor bolt hol s with th slid in plac , g ntly mov
th slid to on sid allowing suffici nt room to drill th anchor bolt hol s. Anchor bolts ar
in Hardwar Kit XS-104-SS.
TIP: B car ful wh n drilling th hol s for th anchor bolts so as not to drill compl t ly
through th d ck. It is also very important not to drill too d p. Th bolt hol s for th long
and short l gs must b drill d to th prop r d pth so that 1-1/4” of th anchor bolts xt nd
abov th d ck. For th st p p d stal, th bolt should xt nd 1-3/4” abov th d ck.
G ntly r position th slid . Position f t ov r th anchor bolts, th n tight n th anchor bolt
nuts. Ch ck and r -tight n ALL SLIDE CONNECTIONS at this tim .
Fig. 14
STEP NINE: Connect the Water Supp y System
Conn ct th bottom 1” PVC Fl x Pip to th custom r install d wat r stub-up, as n c ssary.
It is r comm nd d that th provid d in-lin valv b install d b tw n th slid and th wat r
sourc so that th wat r flow can b adjust d as n c ssary.

I N S T A L L A T I O N M A N U A L X - S T R E A M 2 ™ S L I D E
16
XS2-IM R v. 10/14 (SBK-XS2 INSTALL)
STEP TEN: Finishing Steps
• Install prot ctiv caps on all xpos d bolts.
• Turn wat r supply on and ch ck wat r flow.
• Cl an Slid and dispos of all d bris caus d by th installation.
HINT: It is recommended that after several days of use, all visible bolted connections be
re-tightened as needed.
FINAL INSPECTION / ANNUAL INSPECTION CHECK LIST:
1. M asur th d pth and width of th wat r in front of th slid as w ll as th slid ’s xit
h ight abov wat r to nsur th y conform to Diagrams A, B, and C on pag 4.
2. Ch ck th slid ’s position on th d ck and nsur it conforms to th diagrams on pag s 5-6.
3. Ensur th slid is s cur ly anchor d to th d ck and stabl .
4. Insp ct th runway for visibl cracks or t ars.
5. Insp ct th runway and nsur a smooth, v n sliding surfac . Ensur th gask ts
b tw n th flang s ar compr ss d uniformly.
6. Insp ct th runway for any wat r l aks and adjust wat r flow for v n wat r distribution
across sliding surfac . Ensur wat r do s not splash outsid th runway, and all wat r
running off th slid falls into th pool.
7. Insp ct th slid for any loos or corrod d fast n rs.
8. Ensur th r is a prot ctiv rubb r cap on all xpos d nuts and bolts.
9. Insp ct all st p-attachm nt points and nsur th st ps ar s at d on th nylon support
rods corr ctly.
10. Insp ct th ladd r handrails for rigidity and attachm nt. Can th y b pull d out of th ir
sock ts?
11. Insp ct th slid for sharp dg s or protrusions on th ladd r, d ck flang s, handrails
or runway.
12. Mak sur th slid warning lab l is s cur ly adh r d to th slid .
NOTE: this insta ation is not comp ete unti you, the insta er, gives the owner’s manua
to the customer and then reviews the intended use instructions with them.
X-STREAM™ SLIDE CARE & MAINTENANCE:
Your slid r quir s p riodic maint nanc to k p it looking lik n w.
• Wash monthly or mor fr qu ntly, if n d d. B car ful to k p cl aning mat rial from
nt ring th pool.
• Wash with a mild soap such as hand dishwashing soap, avoid using strong cl an rs or
abrasiv s. Avoid strong alkalin (such as tri-sodium phosphat ) or highly acidic cl an rs.
Avoid bl ach and ammonia.
* These suggestions and data based on information believed to be reliable, from our raw materials
manufa turers. They are offered in good faith, but without guarantee, as onditions and methods
of use and pro edures are beyond our ontrol.

I N S T A L L A T I O N M A N U A L X - S T R E A M 2 ™ S L I D E
17
XS2-IM R v. 10/14 (SBK-XS2 INSTALL)
Wh n installing an Int r-Fab X-Str am™ 2 or G-Forc ™ 2 slid using a pav r kit, you must
nsur that all standard installation r quir m nts ar m t. Th slid must b compatibl with
th typ of pool on th int nd d installation and all ANSI/APSP/ICC-5 2011 r quir m nts
must b m t. R f r to installation manual.
Figure 26 illustrat s an xampl of th minimum concr t pads r comm nd d for th
X-Str am™ 2 slid . Sp cific slid positions and concr t pad ori ntations may vary. Mak
sur to allow for wat r stub up location n ar th ladd r foot on th X-Str am™ 2 slid
wh n pouring th concr t pad for th ladd r foot. In order to ensure proper placement,
you will need to set the slide up first to determine where the concrete pillars will be located.
Figure 25 shows an xampl sid vi w of a slid foot and an w dg anchor us d in a pav r
installation. Pav rs can b a maximum of 3” thick. Pav rs must b m chanically attach d
to th concr t pad using a s tting mat rial (such as mortar or thins t for xampl ) that
is no thick r than 3/8”.
For th long and short support l gs, 1-1/4” of ach 3/8” w dg anchor n ds to b xpos d
abov th final d ck surfac . For th st p p d stal, 1-3/4” n ds to b xpos d. You will
n d to factor in th thickn ss of your pav r (3” MAX.) and th thickn ss of your s tting
mat rial (3/8” MAX.) for your individual installation.
You will n d a 3/8” masonry bit for th X-Str am™ 2 slid .
Inter-Fab Inc. will not be re pon ible for damage to paver cau ed by drilling or mechanically
attaching to concrete pad. Refer to paver manufacturer’ pecific in tallation in truction
before beginning.
X-STREAM 2™ NOTES:
• All X-Str am 2™ w dg anchors (13 a.) ar
3/8” x 7”.
PAVER KIT INFO – X-STREAM 2
Fig. 25
Example of Slide Foot on Concrete Pad (Side View)
CONCRETE
24” min.
Lay r of s tting
mat rial to
s cur pav rs
to concr t .
PAVERS 3”
max.
Drawing I
NOT To Scale
HEIGHT OF WEDGE
ANCHOR ABOVE
FINAL DECK
SURFACE
WEDGE
ANCHORS
24” min.
5” min.
from dg
Fig. 26
Minimum Concrete Pads:
X-STREAM™ 2 Slide
2 concrete pads are needed:
24” wide x 24” long x 24” deep
Center each foot on each pad.
You may rotate
the square pads
as needed.
1 concrete pad:
27” wide x 31” long
x 24” deep
(Plan View – NOT to Scale)

I N S T A L L A T I O N M A N U A L X - S T R E A M 2 ™ S L I D E
18
XS2-IM R v. 10/14 (SBK-XS2 INSTALL)
X-STREAM 2™ SLIDE (XS-GR-SS):