KidKraft F24148E User manual

# F24148E
M
I
S
S
I
N
G
S
O
M
E
T
H
I
N
G
?
•
C
A
L
L
U
S
O
R
G
O
O
N
L
I
N
E
•
OBSTACLE FREE SAFETY ZONE - 22’- 3” L x 28‘ D area requires Protective Surfacing.
See page 4.
MAXIMUM VERTICAL FALL HEIGHT - 6’ (1.8m).
CAPACITY - 6 Users Maximum, Ages 3 - 7; Weight Limit 110 lbs. (49.9 kg) per child.
RESIDENTAL HOME USE ONLY. Not intended for public areas such as multi-unit
residences, schools, churches, nurseries, day cares or parks.
INSTALLATION AND OPERATING INSTRUCTIONS
ASSEMBLY TIME
4 - 8 HOURS
TWO-PERSON
ASSEMBLY
WARNING. ONLY
FOR OUTDOOR
DOMESTIC USE
APPLETON
PLAYSET
Rev 09/17/20219404148E
FOR 24/7 ONLINE PARTS REPLACEMENT
parts.kidkraft.com parts.kidkraft.eu
KidKraft, Inc.
4630 Olin Road
Dallas, Texas 75244
USA
[e-mail] [e-mail]
1.800.933.0771
972.385.0100
[phone]
M-F from 09:00 to 17:30 (GMT+1)
KidKraft Netherlands BV
Olympisch Stadion 8
1076 DE Amsterdam
The Netherlands
To reduce the risk of serious injury or death, please read and follow
these instructions. Keep and refer to instructions as needed and
pass along to any future owners of this item.
WARNING
Easy step-by-step 3D interactive
instructions for this product can be
found in BILT®. Download today.

Congratulations on purchasing a KidKraft product!
Our items are made of high-quality, durable
Cunninghamia Lanceolata wood from the cypress
family. Lumber from these trees are known for their
lightweightandexcellentstrength.Theporosityofthis
wood allows the moisture to absorb and evaporate
in the fibers, resisting rot and bugs. Engineered for
great play, our products also go through extensive
testing for safety. Plus, our team has developed a
series of proprietary methods for a simpler, more
organized assembly. Less build time and more play
time is our motto! However, during assembly if you
have any questions or concerns, please reach out.
Our Customer Service can help with missing parts,
instructions or maintenance.
22

Warnings and Safe Play Instructions
CONTINUOUS ADULT SUPERVISION REQUIRED. Most serious injuries and deaths on playground equipment have occurred
while children were unsupervised! Our products are designed to meet mandatory and voluntary safety standards. Complying
with all warnings and recommendations in these instructions will reduce the risk of serious or fatal injury to children using
this play system. Go over the warnings and safe play instructions regularly with your children and make certain that they
understand and follow them. Remember on-site adult supervision is required for children of all ages.
SERIOUS HEAD INJURY HAZARD
Installation over concrete, asphalt, dirt, grass, carpet
and other hard surface creates a risk of serious injury
or death from falls to the ground. Install and maintain
shock absorbing material under and around play-set as
recommended on page 3 of these instructions.
COLLISION HAZARD
Place play-set on level ground at least 2m from any
obstruction such as a garage or house, fences, poles,
trees, sidewalks, walls, landscape timbers, rocks,
pavement, planters, garden borders, overhanging
branches, laundry lines, and electrical wires. (See
OBSTACLE FREE SAFETY ZONE on cover)
CHOKING HAZARD/SHARP EDGES & POINTS
Adult assembly required. This product contains small
parts and parts with sharp edges and points. Keep parts
away from children until fully assembled.
WARNING LABEL
Owners shall be responsible for maintaining the legibility
of the warning labels.
STRANGULATION HAZARD
,senilsehtolc,seporhtiwyalpotnerdlihcwollaREVEN•
pet leashes, cables, chains or cord-like items when using
this play-set or to attach these items to play-set.
ponchos, hoods, scarves, capes, necklaces, items with
draw-strings, cords or ties when using this play-set.
stemlehtropsroekibraewotnerdlihcwollaREVEN•
when using this play-set.
Failure to prohibit these items, even helmets with chin
straps, increases the risk of serious injury and death to
children from entanglement and strangulation.
TIP OVER HAZARD
Choose a level location for the equipment. This can reduce
the likelihood of the play set tipping over and loose- ll
surfacing materials washing away during heavy rains.
D
Never add extra length to chain or rope. The chains or ropes
provided are the maximum length designed for the swinging
element(s).
O NOT allow children to play on the play-set until the
assembly is complete and the unit is properly anchored.
WARNING
eeS.tes-yalpruoyfosnoitatimilyticapacevresbO
front cover.
gnisolcnetoofllufdnagnittllewhtiwnerdlihcsserD
footwear.
retnecehtnithgiewllufriehthtiwtisotnerdlihchcaeT
of the swing seat to prevent erratic swing motion or
falling off.
,gnissim;doowdekcarcronekorb,deretnilpsrofkcehC
loose, or sharp edged hardware. Replace, tighten and or
sand smooth as required prior to playing.
niahc,sreddalepor,seporgnibmilcdednepsustahtyfireV
or cable are secured at both ends and cannot be looped
back on itself as to create an entanglement hazard.
rehtodnaedilsehtkcehc,syadtohrodnaynnusnO
plastic rides to assure that they are not very hot as to
cause burns. Cool hot slide and rides with water and wipe
dry prior to using.
raewtoofleehroeotneporaewotnerdlihcwollatonoD
like sandals, ip– ops or clogs.
dniheb,neewteb,tnorfni,klawotnerdlihcwollatonoD
or close to moving rides.
poolroseporrosniahcgniwstsiwtnerdlihcteltonoD
them over the top support bar. This may reduce the
strength of the chain or rope and cause premature failure.
.noitomnierayehtelihwsedirffotegnerdlihcteltonoD
.tewsitinehwtnempiuqenognibmilctimreptonoD
anitnempiuqefoesuroyalphguortimreptonoD
manner for which it was not intended. Standing on or
jumping from the roof, elevated platforms, swings,
climbers, ladders or slide can be dangerous.
.staesrosedirytpmegniwsotnerdlihcwollatonoD
rotsrdaehedilsnwodogotnerdlihcwollatonoD
run up slide.
WARNING – Safe Play Instructions
Orientate slide such that it gets the least amount of exposure
to the sun.
33

One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing
protective surfacing under and around your play equipment. The protective surfacing should be applied to a depth that is suitable
for the equipment height in accordance with ASTM F1292. There are different types of surfacing to choose from; whichever
product you select, follow these guidelines:
Loose-Fill Materials
• M
aintain a minimum depth of 9 inches (23 cm) of loose-fill materials such as wood mulch/chips, engineered wood fiber (EWF), or
shredded/recycled rubber mulch for equipment up to 8 feet (2.45 m) high; and 9 inches (23 cm) of sand or pea gravel for equipment up to 5 feet (1.5 m)
high. NOTE: An initial fill level of 12 inches (31 cm) will compress to about a 9-inch (23 cm) depth of surfacing over time. The surfacing will also
compact, displace, and settle, and should be periodically raked and refilled to maintain at least a 9-inch (23 cm) depth.
• U
se a minimum of 6 inches (16 cm) of protective surfacing for play equipment less than 4 feet (1.22 m) in height. If maintained properly, this
should be adequate. (At depths less than 6 inches (16 cm), the protective material is too easily displaced or compacted.)
NOTE: Do not install home playground equipment over concrete, asphalt, or any other hard surface. A fall onto a hard surface
can result in serious injury to the equipment user. Grass and dirt are not considered protective surfacing because wear and
environmental factors can reduce their shock absorbing effectiveness. Carpeting and thin mats are not adequate protective
surfacing. Ground level equipment -- such as a sandbox, activity wall, playhouse or other equipment that has no elevated play
surface-- does not need any protective surfacing.
• Use containment, such as digging out around the perimeter and/or lining the perimeter with landscape edging. Don’t forget to
account for water drainage.
• Periodically rake, check and maintain the depth of the loose-fill surfacing material. Marking the correct depth on the play
equipment support posts will help you to see when the material has settled and needs to be raked and or replenished. Be sure to
rake and evenly redistribute the surfacing in heavily used areas.
• Do not install loose fillsurfacing over hard surfaces such as concrete or asphalt.
Poured-In-Place Surfaces or Pre-Manufactured Rubber Tiles
You may be interested in using surfacing other than loose-fill materials - like rubber tiles or poured-in-placesurfaces.
• Installations of these surfaces generally require a professional and are not “do-it yourself ” projects.
• Review surfacespecifications before purchasing this type of surfacing. Ask the installer/manufacturer for a report showing that
the product has been tested to the following safety standard: ASTM F1292 Standard Specification for Impact Attenuation of Surfacing
Materials within the Use Zone of Playground Equipment. This report should show the specific height for which the surfaceis intended
to protect against serious head injury. This height should be equal to or greater than the fall height - vertical distance between a
designated play surface (elevated surface for standing, sitting, or climbing) and the protective surfacing below - of your play equipment.
• Check the protective surfacing frequently for wear.
Placement
Proper placement and maintenance of protective surfacing is essential. Refer to diagram on front cover. Be sure to;
• Extend surfacing at least 6 feet (1.8 m) from the equipment in all directions.
• For to-fro swings, extend protective surfacing in front of and behind the swing to a distance equal to twice the height of the top
bar from which the swing is suspended.
• F
or tire swings, extend surfacing in a circle whose radius is equal to the height of the suspending chain or rope, plus 6 feet (1.8 m) in all directions.
Protective Surfacing-Reducing Risk of Serious Head Injury From Falls
From the CPSC Outdoor Home Playground Safety Handbook. At http://www.playgroundregs.com/resources/CPSC%20324.pdf
Denotes Use Zone with Protective Surfacing
Denotes Use Zone with Protective Surfacing
6 ft.
6 ft.
6 ft. (1.8m)
6 ft. (1.8m)
(1.8m)
6 ft.
(1.8m)
(1.8m)
6 ft.
(1.8m)
6 ft.
(1.8m)
Use Zone for Multi-Axis SwingsUse Zone for Single-Axis Swings
44

Instructions for Proper Maintenance
sand and repaint using a non-lead paint
splinteringof wood.
Check for sharp edges or protrudingscrew threads, add
washers if required.
fill protective surfacing materials to prevent compaction and
Check for looseness, damage ordeterioration. Should firmly
if necessary.
Check that bolts are secure and tight. Quick clips should be
completely closed and threaded clips screwed tight.
parts including swingseats, ropes, chains and attachments
Check that ropes are tight, secure at both ends and cannot
loop back as to create an entrapment.
Check all wood members fordeterioration, structural
damage and splintering. Sand down splinters and replace
deteriorated wood members. As with all wood, some
checking and small cracks in grain is normal.
basis is important maintenance to maintain maximum life
and performance oftheproduct.
Check the following at the beginning of the play season:
This will causesplinteringof wood.
Check for sharp edges orprotrudingscrew threads.
Add washers ifrequired.
materials to prevent compaction and maintain appropriate
Check twice a month during play season:
Check that they are secure and orientated correctly. Hook
should rotate freely and perpendicular to support beam.
Check swingseats, all ropes, chains and attachments for
fraying, wear, excessive corrosion ordamage.
Check once a month during play season:
To prolongtheir life, remove swings and store insidewhen
plasticparts may become morebrittle.
materials to prevent compaction and maintain appropriate
Check at the end of the play season:
If you disposeof your play set:
hazards at thetime it is discarded. Besure to follow yourlocal wasteordinances.
beyond T-Nut
flat washer
Your KidKraft Play System is designed and constructed of quality materials with your child’s safety in mind. As with
all outdoor products used by children, it will weather and wear. To maximize the enjoyment, safety and life of your
Play Set, it is important that you, the owner, properly maintain it.
55

About Our Wood
KidKraft Premium Play Systems uses only premium playset lumber, ensuring the safest product for your
children’s use. Although we take great care in selecting the best quality lumber available, wood is still a
product of nature and susceptible to weathering which can change the appearance of your set.
What causes weathering? Does it affect the strength of my Play System?
One of the main reasons for weathering is the effects of water (moisture); the moisture content of the wood
at the surface is different than the interior of the wood. As the climate changes, moisture moves in or out
of the wood, causing tension which can result in checking and or warping. You can expect the following
due to weathering. These changes will not affect the strength of the product:
1. Checking is surface cracks in the wood along the grain. A post 4” x 4” (101mm x 101mm) will experience
more checking than a board 1” x 4” (25mm x 101mm) because the surface and interior moisture content
will vary more widely than in
thinner wood.
2. Warping results from any distortion (twisting, cupping) from the original plane of the board and often
happens from rapid wetting and drying of the wood.
3. Fading happens as a natural change in the wood color as it is exposed to sun-light and will turn a grey
over time.
How can I reduce the amount of weathering to my Play System?
At the factory we have coated the wood with a water repellent or stain. This coating decreases the amount
of water absorption during rain or snow thus decreasing the tension in the wood. Sunlight will break down
the coating, so we recommend applying a water repellent or stain on a yearly basis (see your local stain
and paint supplier for a recommended product).
Most weathering is just the normal result of nature and will not affect safe play and enjoyment for your
child. However if you are concerned that a part has experienced a severe weathering problem please call
our consumer relations department for further assistance.
Complete and mail registration card to receive important product notifications and assure prompt
warranty service.
66

KidKraft Limited Warranty
MISSING OR DAMAGED PARTS:
KidKraft will replace any parts within 90 days from date of purchase found to be missing from or
damaged in the original packaging. See Fig.1
Fig. 1 Product Age (All Parts) Consumer Pays
0-90 Days from date of purchase $0 for Part + Free Shipping
DEFECTS IN MATERIAL AND WORKMANSHIP:
KidKraft warrants that this product is free from defects in materials and workmanship for a period of one
(1) year from the original date of purchase (dated sales receipt and/or product registration is required).
This one (1) year warranty covers all parts including wood, hardware, and all accessories (Such as
swings, rides, and slides). See Fig. 2
Fig. 2 Product Age (All Parts) Consumer Pays
91 Days to 1 Year $0 for Part + Free Shipping
WOOD ROT, DECAY, AND INSECT DAMAGE:
All wood carries a five (5) year warranty against rot, decay, and insect damage (dated sales receipt
and/or product registration is required). Refer tothe schedule below for charges associated with
replacement of wood parts under this Limited Warranty. See Fig. 3
Fig. 3 Product Age (Wood Parts) Consumer Pays
0 Days to 1 Year $0 for Part + Free Shipping
After 1 Year to 5 Year $0 for Part + Shipping & Handling
Over 5 Years 100% for Part (if available) + Shipping & Handling
This warranty applies to the original owner and registrant and is non-transferable. Regular maintenance
is required to ensure the integrity of this product. Failure by the owner to maintain the product according
to the maintenance requirements may void this warranty.
This Limited Warranty does NOT cover:
• Any inspection cost
• Labor and/or costs for replacement of any defective item(s), including but not limited to,
professional installer costs
• Incidental or consequential damages, including but not limited to, as a result of set relocation,
move and/or reinstall
• Cosmetic defects which do not affect performance or integrity of a part or the entire product
• Vandalism, improper use or installation, or acts of nature, including but not limited to, high winds,
fire, and flood
• Minor twisting, warping, checking, or any natural occurring properties of wood that do not affect
performance or integrity.
• Any KidKraft product purchased, including but not limited to, a non-approved retailer, auction
houses, second-hand, and as-is clearance items.
KidKraft products have been designed for safety and quality. Modifications made to the original product
may damage the structural integrity of the unit leading to failure and possible injury. KidKraft cannot
assume any responsibility for the modified products. Furthermore, modifications void all warranties.
This product is warranted for RESIDENTIAL USE ONLY. Under no circumstance should a KidKraft
product be used in public settings such as schools, churches, playgrounds, parks, home and
professional day cares and the like. Such use may lead to product failure and potential injury. Public use
will void this warranty. KidKraft disclaims all other representations and warranties of any kind, express or
implied.
77

This identifies information that requires special
attention. Improper assembly could lead to an unsafe
or dangerous condition.
Where this is shown, 2 or 3 people
are required to safely complete the
step. To avoid injury or damage
to the assembly make sure to get
help!
Check that assembly is square
before tightening bolts.
Use a measuring tape to assure
proper location.
Check that set or assembly is properly level
before proceeding.
Pre-drill a pilot hole
before fastening screw
or lag to prevent
splitting of wood.
This indicates time to tighten bolts, but
not too tight! Do not crush the wood.
This may create splinters and cause
structural damage.
Part Identification Key
On each page, you will find the parts
and quantities required to complete the
assembly step illustrated on that page.
Here is a sample.
Key Number: The first two digits
represent the step number. The third
digit represents the piece. Note that if
the part is used in multiple steps then
the number only reflects the first step it
is used in.
Symbols
Throughout these instructions symbols are provided as important reminders for proper and safe assembly.
Proper Hardware Assembly
Lag screws require drilling pilot
holes to avoid splitting wood. Only
a flat washer is required. For ease of
installation liquid soap can be used
on all lag-type screws.
For bolts, tap T-Nut into hole with
hammer. Insert the hex bolt through
lock washer first then flat washer then
hole. Because the assemblies need to
be squared do not completely tighten
until instructed. Pay close attention to
diameter of the bolts. 5/16” (8mm) is slightly
larger than 1/4” (6.4mm).
Note: Wafer head bolts with blue lock
tight or a bolt with a Ny-Lok nut do
NOT require a lock washer.
Once the assembly is tightened, watch for exposed threads.
If a thread protrudes from the T-Nut, remove
the bolt and add washers to eliminatethis condition.
Extra washers have been provided for this purpose.
Use
Help
Use
Help
Measure
Distance
Square
Assembly
Use
Level
Pre-drill 1/8”(3mm) & 3/16”(5mm) Bit
Tighten
Bolts
CAUTION – Protrusion Hazard
Keys to Assembly Success
Tools Required
Quantity Key Number Part Description,
Part Size
2X 1012 P
No Yes
Lag Assembly
Bolt Assembly
Flat Washer
Lag Screw
Hex Bolt
Lock
Washer
Flat
Washer
Before mounting Lag
Screw, use factory drilled
holes as guides to drill 1/8”
(3.2mm) pilot holes
T-Nut
(Hammer into place)
Do not crush wood!
If Bolt protrudes
beyond T-Nut
Use an extra
flat washer
• Tape Measure
• Carpenters Level
• Carpenters Square
• Claw Hammer
• Standard or Cordless Drill
• Rubber Mallet
• #1 Phillips, #2 Robertson
and Screwdriver
• Ratchet with extension
1/2” (13mm) & 9/16”(14 mm)
sockets
• Open End Wrench
1/2” (13mm) & 9/16”(14 mm)
• Adjustable Wrench
• 1/8”(3mm) & 3/16”(5mm)
Drill Bits
• 3/16”(5mm) Hex Key
• 8’ (2.4m) Step Ladder
• Safety Glasses
• Adult Helpers
• Pencil
3mm 5mm
ost 2 x 4 x 83” (5 cm x 10 cm x 210 cm)
88

1 inch = 25.4mm
KIDKRAFT DESIGN HARDWARE
For example:
BOLT LENGTH 4½ (4.5) inches long
114mm long
1 inch = 25.4mm
25.4mm
4.5 inches x
DIAMETER CONVERSION
LENGTH CONVERSION
=
BOLT DIAMETER 5/16 (0.31) inches 0.31 inches x 25.4mm = 8mm
For example:
HARDWARE LENGTH CHART
inches vs millimetres
6 152
5½ 140
5 127
4½ 114
4 102
3½ 89
3 76
2½ 64
2 51
1½ 38 1¼ 32
1-1/8 29
1 25.4
7/8 22 3/4 19 1/2 12.7
1/4" (6mm) Flat Washer
1/4" (6mm) Lock Washer
1/4"(0.25) = 6mm Hex Bolt
1/4" (6mm) T-Nut
5/16"(.31) = 8mm Lag Screw
5/16" (8mm) Flat Washer
1/4"(0.25) = 6mm Lag Screw
1/4" (6mm) Flat Washer
5/16" (8mm) Flat Washer
5/16" (8mm) Lock Washer
5/16"(.31) = 8mm Hex Bolt
5/16" (8mm) T-Nut
3/8"(.38) = 9.5mm Lag Screw
3/8" (9.5mm) Flat Washer
99

1773 3631773 Box 1
(1) CE Sw Beam - Front 2 x 6 x 69-1/2"
1774 3631774 Box 1
(2) CE Gap Board 1 x 6 x 23-1/2"
1776 3631776 Box 1
(5) Floor Board 1 x 6 x 23-1/2"
1777 3631777 Box 1
(2) CE Rock Board B 1 x 6 x 17"
WOOD CHART
(4) CE Floor Board 1 x 4 x 32-1/2"
3630304 Box 1
0304
Part Identification (Reduced Size)
2" x 6"
2" x 4"
2" x 3"
2" x 2"
5/4" x 4"
5/4" x 5"
5/4" x 6"
1" x 6"
1" x 5"
1" x 4"
1" x 2"
Actual Size
1½" x 5⅜"
1⅜" x 3⅜"
1⅜" x 2½"
1½" x 1½"
1" x 3½"
1" x 4½"
1" x 5½"
⅝" x 5⅜"
⅝" x 4½"
⅝" x 3⅜"
⅝" x 1⅜"
Nominal Size
1772 3631772 Box 1
(1) CE Sw Beam - Back 2 x 6 x 69-1/2"
0312 3640312 Box 1
(1) Gusset 2 x 3 x 16"
1779 3631779 Box 1
(1) CE Access Board 1 x 6 x 17"
1778 3631778 Box 1
(2) CE Rock Board A 1 x 6 x 17"
3640359 Box 1
0359
(2) Front Divider 1 x 4 x 38"
3641797 Box 1
1797
(2) Side Top 1 x 4 x 51-1/2"
3632803 Box 1
(2) Sw Post 2 x 4 x 79-1/2"
2803
3640369 Box 1
0369
(1) Lower Diagonal 2 x 3 x 37"
1010

1754 3641754 Box 1
(1) Lower Back Wall 1 x 4 x 31-1/2"
1752 3641752 Box 1
(1) Top Front 1 x 4 x 38-1/2"
1751 3641751 Box 1
(1) Centre Divider 2 x 2 x 38"
Part Identification (Reduced Part Size)
Actual Size
1½" x 5⅜"
1⅜" x 3⅜"
1⅜" x 2½"
1½" x 1½"
1" x 3½"
1" x 4½"
1" x 5½"
⅝" x 5⅜"
⅝" x 4½"
⅝" x 3⅜"
⅝" x 1⅜"
2" x 6"
2" x 4"
2" x 3"
2" x 2"
5/4" x 4"
5/4" x 5"
5/4" x 6"
1" x 6"
1" x 5"
1" x 4"
1" x 2"
Nominal Size
3641758 Box 1
1758
(1) Top Back 1 x 4 x 38-1/2"
WOOD CHART
3641796 Box 1
(2) Top End 1 x 4 x 46-1/2"
1796
(1) Sw Support 5/4 x 4 x 48-1/2"
4921 3644921 Box 1
(1) Sw Upright 2 x 4 x 50-1/2"
3644920 Box 1
4920
3641761 Box 1
1761
(1) Side Joist 2 x 2 x 34-3/4"
3641762 Box 1
1762
(1) Floor Back 5/4 x 4 x 38-5/8"
3641794 Box 1
(1) Ridge 2 x 2 x 46-1/2"
1794
3641759 Box 1
1759
(2) SW Floor 1 x 6 x 26-7/8"
(1) Tarp Upright 2 x 2 x 60"
3632783 Box 1
2783
3632782 Box 1
(1) SW Mount 2 x 4 x 60"
2782
1111

3641765 Box 1
1765
(2) Rock Rail 2 x 3 x 42-3/4"
3641766 Box 1
1766
(3) Corner Block 2 x 3 x 4-1/2"
3641767 Box 1
1767
(1) Lower Front 1 x 6 x 39-3/4"
3641768 Box 1
1768
(1) Lower Back 1 x 5 x 38-1/2"
3641763 Box 1
1763
(1) Floor Joist 5/4 x 2 x 38-1/2"
Part Identification (Reduced Part Size)
3641764 Box 1
1764
(1) Floor Front 2 x 3 x 38-1/2"
3641771 Box 1
1771
(4) Post 2 x 4 x 74"
3641770 Box 1
1770
(1) SW Ground 1 x 5 x 60-1/4"
3641769 Box 1
1769
(1) Ground Side 1 x 5 x 42-1/4"
4919 3644919 Box 1
(1) Sw Rail Block 2 x 4 x 5-3/8"
1X 3200184
Triangle Plate (4pk)
Green
1X 3320184 Rocks (4pk)
Green
1X 3750703
Inglewood Canopy
1X 3750704
Pine Ridge Chalk Wall
1X 3201103
Corner Brace Set
(4pk)
1X 3310140
40" High Rail Slide
Green
1X 9330355
KidKraft ID
Plaque
3650318 Box 1
(4) Ground Stake 1-1/4 x 1-1/2 x 14"
0318
2X 3724949
43" EN71 Belt Swing
Rope Yellow
4X 9300000
Swing Hanger
Covers
1212

(44) LW1 - 1/4" Lock Washer - (9253200)
(17) FW2 - 5/16" Flat Washer - (9251300)
(43) FW1 - 1/4" Flat Washer - (9251200)
(16) FW0 - 3/16" Flat Washer - (9251100)
Hardware Identification (Actual Size)
(15) S3 - Wood Screw #8 x 2-1/2" - (52042522)
(6) S4 - Wood Screw #8 x 3" - (52042530)
(14) S7 - Pan Screw #12 x 2" - (9264620)
(4) S10 - Pan Screw #8 x 1" - (9264510)
(6) PB2 - Pan Bolt 1/4 x 1-1/4" - (9274211)
(24) FW3 - #8 Flat Washer - (9251500)
(20) S1 - Wood Screw #8 x 1-1/8" - (52042514)
(71) S2 - Wood Screw #8 x 1-1/2" - (52042512)
(10) S15 - Wood Screw #8 x 1-3/4" - (52042513)
2x2 Robertson Driver - (9200014)
(13) LW2 - 5/16" Lock Washer - (9253300)
(40) S5 - Pan Screw #8 x 1/2" - (9264504)
(13) TN2 - 5/16" T- Nut - (9285300)
(2) LN2 - 5/16" Lock Nut - (9283300)
(40) TN1 - 1/4" T - Nut -(9285200)
(4) BN1 - 1/4" Barrel Nut - (9248200)
1313

(1) H8 - Hex Bolt 1/4 x 4-1/4" - (9277241)
Hardware Identification (Actual Size)
(2) H1 - Hex Bolt 1/4 x 1-1/2" - (9277212)
(2) H3 - Hex Bolt 1/4 x 2-1/2" - (9277222)
(24) H2 - Hex Bolt 1/4 x 2" - (9277220)
(2) H6 - Hex Bolt 1/4 x 4-3/4" - (9277243)
(1) H11 - Hex Bolt 1/4 x 2-3/4" - (9277223)
(3) LS3 - Lag Screw 1/4 x 3" - (9262230)
(5) G5 - Hex Bolt 5/16 x 4-1/2" - (9277342)
(4) G4 - Hex Bolt 5/16 x 4" - (9277340)
(4) H7 - Hex Bolt 1/4 x 5-1/2" - (9277252)
(2) H5 - Hex Bolt 1/4 x 4-1/2" - (9277242)
(2) G8 - Hex Bolt 5/16 x 2" - (9277320)
(4) G1 - Hex Bolt 5/16 x 1-1/2" - (9277312)
(1) Swing Hanger Bolt Thru
(4Pk) - (3202000)
1414

B. If there are any missing or damaged pieces or you need assistance with
assembly please contact the Consumer Relations Department directly. Call us
before going back to the store.
STOPSTOP STOP STOP
Step 1: Inventory Parts - Read This Before Starting Assembly
• Please refer to Page 6 for proper hardware assembly.
• Each step indicates which bolts and/or screws you will need for assembly, as well as
any at washers, lock washers, t-nuts or lock nuts.
A. This is the time for you to inventory all your hardware, wood and accessories,
referencing the parts identication sheets. This will assist you with your assembly.
• The wood pieces will have the four digit key number stamped on the ends of the
boards. The wood pieces are referenced throughout the instructions with this number.
MODEL NUMBER: F24148E
TRACKING NUMBER (from ID Plaque):
[phone]
[email protected]
For online parts replacement visit
https://parts.kidkraft.eu/
1.800.933.0771 or 972.385.0100
[email protected]
[email protected]
For online parts replacement visit
https://parts.kidkraft.com/
Batch #: __ __ __ __ __ __ ___ (Box 4)
Batch #: __ __ __ __ __ __ ___ (Box 5)
Batch #: __ __ __ __ __ __ ___ (Box 6)
Batch #: __ __ __ __ __ __ ___ (Box 1)
Batch #: __ __ __ __ __ __ ___ (Box 2)
Batch #: __ __ __ __ __ __ ___ (Box 3)
C. Read the assembly manual completely, paying special attention to ANSI warnings;
notes; and safety/maintenance information on pages 1 - 8.
D. Before you discard your cartons ll out the form below.
• The Batch # is located on the end of each carton. The tracking number is located on
the KidKraft ID Plaque (9330355).
• Please retain this information for future reference. You will need this information if you
contact the Consumer Relations Department.
1515

16
Step 1: Swing Beam Assembly
Warning: For your childs safety,
orientate the swing hangers as
shown to ensure your swing will
have proper swing motion when
installed. Failure to do so could
result in premature failure of the
swing hanger or swing chain.
Bolt Thru Hangers
Fig. 1.1
Fig. 1.2
Front
Back
Front
Back
Make sure triangle is
tight against beam
Important!
Fort End Side
(No Overhang)
Important!
Swing End
(With Overhang)
Triangle Plates
1 x CE SW Beam Front 2 x 6 x 69-1/2”
1 x CE SW Beam Back 2 x 6 x 69-1/2”
Hardware
Wood Parts
Fig. 1.3
Other Parts
4 x Bolt Thru Swing Hangers
1 x Triangle Plates (pkg of 4)
x 4
x 4
A: In the middle holes of (1772)
CE SW Beam Back install 2 Bolt
Thru Swing Hangers making sure
the swing hangers are oriented in
the direction shown in g. 1.3 to
maintain proper swing motion.
B: In the end holes of (1773) CE
SW Beam Front install 2 Bolt-Thru
Swing Hangers making sure the
swing hangers are oriented in
the direction shown in g. 1.3 to
maintain proper swing motion.
C: Attach 1 (H7) 1/4 x 5-1/2” Hex
Bolt (with lock washer, at washer
and t-nut) to the ends of each
(1772) CE SW Beam Back and
(1773) CE SW Beam Front. The
bolts do not attach to anything, but
MUST be installed to the beams to
prevent splitting and checking of
wood. (g. 1.1)
D: Attach 1 Triangle Plate to each end of both the (1773) CE SW Beam Front and (1772) CE SW Beam Back using
1 (G1) 5/16 x 1-1/2” Hex Bolt (with lock washer, at washer and t-nut) per Triangle Plate in the hole indicated in g.
1.2. Correct hole usage is very important. Refer to g 1.2 for correct placement of Hex Bolts.
4 x 5/16 x 1-1/2” Hex Bolt
 (5/16”lockwasher,5/16”atwasherand5/16”t-nut)
4 x 1/4 x 5-1/2” Hex Bolt
(1/4”lockwasher,1/4”atwasherand1/4”t-nut)
G1
H7
H7
G1
1773
1772
1772
1773
1773
1772

17
Step 2: Swing End Assembly
Fig 2.1
2 x SW Post 2 x 4 x 79-1/2”
1 x SW Upright 2 x 4 x 50-1/2”
1 x SW Support 5/4 x 4 x 48-1/2”
Hardware
Wood Parts
2 x 5/16 x 4” Hex Bolt
 (5/16”lockwasher,5/16”atwasher,and5/16”t-nut)
3 x 5/16 x 4-1/2” Hex Bolt
(5/16”lockwasher,5/16”atwasher,and5/16”t-nut)
G4
G5
G4
G5
A: Attach 2 (2803) SW Posts to (4920) SW Upright using 2 (G4) 5/16 x 4” Hex Bolts (with lock washer, at washer
and t-nut). (g. 2.1)
B: Attach (4921) SW Support to both (2803) SW Posts and (4920) SW Upright using 3 (G5) 5/16 x 4-1/2” Hex
Bolts (with lock washer, at washer and t-nut). (g. 2.1)
2803 4920
4921
2803
4920
2803
4921

18
Step 3: Swing Beam
Fig. 3.1
Side with
Overhang
H8
Fig. 3.2
Fig. 3.3
Fig. 3.4
G5
G8
1 x SW Rail Block 2 x 4 x 5-3/8”
Hardware
Wood Parts 1 x 1/4 x 4-1/4” Hex Bolt
 (1/4”lockwasher,1/4”atwasher,1/4”t-nut)
1 x 5/16 x 4-1/2” Hex Bolt
(5/16”lockwasher,5/16”atwasher,5/16”t-nut)
1 x 5/16 x 2” Hex Bolt
(5/16”atwasherx2,5/16”locknut)
H8
G5
A: Place (4919) SW Rail Block in the centre between (1773) CE SW Beam Front and (1772) CE SW Beam Back
and attach beams with 1 (H8) 1/4 x 4-1/4” Hex Bolt (with at washer, lock washer and t-nut). (g. 3.1 & 3.2)
B: Attach Swing Beam Assembly to the side of the Swing End Assembly with the overhang (g. 3.3) using 1 (G5)
5/16 x 4-1/2” Hex Bolt (with lock washer, at washer and t-nut) in the top hole of Triangle Plate and 1 (G8) 5/16 x
2” Hex Bolt (with 2 at washers and lock nut) in the bottom hole of Triangle Plate. (g. 3.3) Make sure Swing End
Assembly ares out at an angle. (g 3.4)
G8
4919
4919 1773
1772

19
1 x Side Top 1 x 4 x 51-1/2”
Step 4: Swing Side Assembly
Note: Pre-drill all holes using a 1/8” drill bit before installing the lag screws.
H2
2 x Post 2 x 4 x 74”
1 x SW Ground 1 x 5 x 60-1/4”
1 x SW Floor 1 x 6 x 26-7/8”
1 x Lower Diagonal 2 x 3 x 37”
1 x SW Mount 2 x 4 x 60”
Hardware
Wood Parts
11x 1/4x2”HexBolt(1/4”lockwasher,1/4”atwasher,1/4”t-nut)
2 x 5/16 x 4” Hex Bolt (5/16”lockwasher,5/16”atwasher,5/16”t-nut)
1x 1/4x3”LagScrew(with1/4”atwasher)
2 x #8 x 1-1/2” Wood Screw
LS3
Fig. 4.1
Notice hole
location
H2 H2
LS3
G4
H2
H2
G4
Fig. 4.2
A: To 2 (1771) Posts attach (1770) SW Ground and (1759) SW Floor using 4 (H2) 1/4 x 2” Hex Bolts (with lock
washer, at washer and t-nut) in each board. Be sure to keep bolts loose. (g. 4.1)
B: Attach (1797) Side Top to each
(1771) Post with 2 (H2) 1/4 x 2” Hex
Bolts (with lock washer, at washer and
t-nut) Hex Bolts are to be installed from
the back of the assembly. Be sure to
keep bolts loose. (g. 4.2)
C: Make sure assembly is square and
then fasten (0369) Lower Diagonal to
(1770) SW Ground at an angle using 1
(H2) 1/4 x 2” Hex Bolt (with lock washer,
at washer and t-nut) and to (1771) Post
using 1 (LS3) 1/4 x 3” Lag Screw (with
at washer). (g 4.2).
D: Attach (2782) SW Mount to (1759)
SW Floor and (1797) Side Top with
2 (G4) 5/16 x 4” Hex Bolts (with lock
washer, at washer and t-nut). (g. 4.2)
E: Tighten all bolts then attach (1797)
Side Top to each (1771) Post with 1 (S2)
#8 x 1-1/2” Wood Screw per post. (g.
4.2)
H2
1771 1797
1770
1759
0369
2782
1771
1759
1770
1797
1771
1759
0369
1770
H2
G4
1771
2782
S2
S2
S2

20
Step 5: Wall Side Assembly
H2 H2
2 x Post 2 x 4 x 74”
1 x Ground Side 1 x 5 x 42-1/4”
1 x SW Floor 1 x 6 x 26-7/8”
1 x Corner Block 2 x 3 x 4-1/2”
1 x Side Top 1 x 4 x 51-1/2”
Hardware
Wood Parts
12 x 1/4 x 2” Hex Bolt
 (1/4”lockwasher,1/4”atwasher,1/4”t-nut)
4 x #8 x 1-1/2” Wood Screw
H2
S2
A: To 2 (1771) Posts loosely attach (1759) SW Floor and (1769) Ground Side with 4 (H2) 1/4 x 2” Bolts (with
lock washer, at washer and t-nut) per board. (g. 5.1)
B: Loosely attach (1797) Side Top to each (1771) Post with 2 (H2) 1/4 x 2” Hex Bolts (with lock washer, at
washer and t-nut). These Hex Bolts are to be installed from the back of the assembly. (g. 5.1)
C: Attach (2783) Tarp Upright to (1759) SW Floor and (1797) Side Top with 2 (H2) 1/4 x 2” Hex Bolts (with lock
washer, at washer and t-nut). Tighten all bolts and attach (1797) Side Top to each (1771) Post with 1 (S2) #8 x
1-1/2” Wood Screw per post. (g. 5.1 and 5.2)
D: Attach (1766) Corner Block ush to angled extension of (1769) Ground Side with 2 (S2) 8 x 1-1/2” Wood
Screws as shown in g. 5.2 and 5.3.
Fig. 5.2
Fig. 5.1 Notice hole towards back
Back
1 x Tarp Upright 2 x 2 x 60”
2783
1771
1769
1759
1766
1797
x 4
x 4
x 2
H2
S2
1797 1771
1759
1769
2783
H2
1797
1759
1769
1769
S2
1766
Flush