KidKraft F29060 User manual

INSTALLATION AND OPERATING INSTRUCTIONS
To reduce the risk of serious injury or death, you must
read and follow these instructions. Keep and refer to
these instructions often and give them to any future
owner of this play system. Manufacturer contact information provided below.
OBSTACLE FREE SAFETY ZONE - 26’0.20” x 17’1.24” (7.930 x 5.213 m) area requires
Protective Surfacing. See Page 3
MAXIMUM VERTICAL FALL HEIGHT - 2’11.47”(0.9 m)
CAPACITY - 8Users Maximum, Ages 3to 10; Weight Limit 110 lbs. (49.9 kg) per child.
RESIDENTIAL HOME USE ONLY. Not intended for public areas such as schools,
churches, nurseries, day cares or parks.
Warning. Only for domestic use.
WARNING
Rev 11/23/20189409060
Table of Contents
Warnings and Safe Play Instructions..........pg. 2
Protective Surfacing Guidelines. . . . . . . . . . . . . . . pg. 3
Instructions for Proper Maintenance .........pg. 4
About Our Wood – Limited Warranty.........pg. 5
Battery Instruction and Warranty ............pg. 6
Keys to Assembly Success ................ pg. 7-10
Part ID ..................................pg. 11-14
Step-By-Step Instructions ...............pg. 15-47
Installation of I.D./Warning Plaque......Final Step
HIGHLINE
RETREAT
F29060
2.5 - 4 Hrs
TWO PERSON
ASSEMBLY
KidKraft, Inc.
4630 Olin Road
Dallas, Texas 75244 USA
[email protected]
[email protected]
1.800.933.0771
972.385.0100
For online parts replacement visit
https://parts.kidkraft.com/
KidKraft Netherlands BV
Olympisch Stadion 29
1076DE Amsterdam
The Netherlands
[email protected]
[phone] M-F from 09:00 to 17:30
(GMT+1)
For online parts replacement visit
https://parts.kidkraft.eu/
17' 1.24"
5.213
26' 0.20"
7.930
3' 11.77"
1.213
12' 10.73"
3.930

2
Warnings and Safe Play Instructions
CONTINUOUS ADULT SUPERVISION REQUIRED. Most serious injuries and deaths on playground equipment have occurred
while children were unsupervised! Our products are designed to meet mandatory and voluntary safety standards. Complying
with all warnings and recommendations in these instructions will reduce the risk of serious or fatal injury to children using
this play system. Go over the warnings and safe play instructions regularly with your children and make certain that they
understand and follow them. Remember on-site adult supervision is required for children of all ages.
SERIOUS HEAD INJURY HAZARD
Installation over concrete, asphalt, dirt, grass, carpet
and other hard surface creates a risk of serious injury
or death from falls to the ground. Install and maintain
shock absorbing material under and around play-set as
recommended on page 3 of these instructions.
COLLISION HAZARD
Place play-set on level ground at least 2m from any
obstruction such as a garage or house, fences, poles,
trees, sidewalks, walls, landscape timbers, rocks,
pavement, planters, garden borders, overhanging
branches, laundry lines, and electrical wires. (See
OBSTACLE FREE SAFETY ZONE on cover)
CHOKING HAZARD/SHARP EDGES & POINTS
Adult assembly required. This product contains small
parts and parts with sharp edges and points. Keep parts
away from children until fully assembled.
WARNING LABEL
Owners shall be responsible for maintaining the legibility
of the warning labels.
STRANGULATION HAZARD
,seni lsehtolc,seporht iwyalpotnerdl ihcwol laREVEN•
pet leashes, cables, chains or cord-like items when using
this play-set or to attach these items to play-set.
ponchos, hoods, scarves, capes, necklaces, items with
draw-strings, cords or ties when using this play-set.
stemlehtropsroekibraewotnerdl ihcwol laREVEN•
when using this play-set.
Failure to prohibit these items, even helmets with chin
straps, increases the risk of serious injury and death to
children from entanglement and strangulation.
TIP OVER HAZARD
Choose a level location for the equipment. This can reduce
the likelihood of the play set tipping over and loose-fill
surfacing materials washing away during heavy rains.
DO NOT allow children to play on the play-set until the
assembly is complete and the unit is properly anchored.
Never add extra length to chain or rope. The chains or ropes
provided are the maximum length designed for the swinging
element(s).
WARNING
eeS. t es-ya l pruoyfosno i t a t imi ly t i capacevresbO
front cover.
gn i so l cnet oo f l l u fdnagn i t t fil l ewh t iwne rd l i hcsse rD
footwear.
retnecehtnithgiewl lufr iehtht iwt isotnerdl ihchcaeT
of the swing seat to prevent erratic swing motion or
falling off.
, gn i ss im; doowdekcarcronekorb, de re tn i l psrofkcehC
loose, or sharp edged hardware. Replace, tighten and or
sand smooth as required prior to playing.
n i ahc, s r edda lepor, seporgn i bmi l cdednepsust ah ty f i r eV
or cable are secured at both ends and cannot be looped
back on itself as to create an entanglement hazard.
r eh t odnaed i l seh tkcehc, syadt ohr odnaynnusnO
plastic rides to assure that they are not very hot as to
cause burns. Cool hot slide and rides with water and wipe
dry prior to using.
r aewt oo f l eehroeo tnepor aewo tne rd l i hcwo l l at onoD
like sandals, flip–flops or clogs.
dniheb,neewteb, tnorfni,klawotnerdl ihcwol latonoD
or close to moving rides.
poolroseporrosniahcgniwstsiwtnerdl ihcteltonoD
them over the top support bar. This may reduce the
strength of the chain or rope and cause premature failure.
.noi tomnierayehtel ihwsedi rf fotegnerdl ihcteltonoD
. t ews i t inehwt nemp i uqenogn i bmi l ct imr ept onoD
an i t nemp i uqef oesur oya l phguo r t imr ept onoD
manner for which it was not intended. Standing on or
jumping from the roof, elevated platforms, swings,
climbers, ladders or slide can be dangerous.
.staesrosedi rytpmegniwsotnerdl ihcwol latonoD
rotsrfidaehed i l snwodogo tne r d l i hcwo l l at onoD
run up slide.
WARNING – Safe Play Instructions
Orientate slide such that it gets the least amount of exposure
to the sun.

3
One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing
protective surfacing under and around your play equipment. The protective surfacing should be applied to a depth that is suitable
for the equipment height in accordance with ASTM F1292. There are different types of surfacing to choose from; whichever
product you select, follow these guidelines:
Loose-Fill Materials
• Maintain a minimum depth of 9 inches of loose-fill materials such as wood mulch/chips, engineered wood fiber (EWF), or
shredded/recycled rubber mulch for equipment up to 8 feet high; and 9 inches of sand or pea gravel for equipment up to 5 feet
high. NOTE: An initial fill level of 12 inches will compress to about a 9-inch depth of surfacing over time. The surfacing will also
compact, displace, and settle, and should be periodically raked and refilled to maintain at least a 9-inch depth.
• Use a minimum of 6 inches of protective surfacing for play equipment less than 4 feet in height. If maintained properly, this
should be adequate. (At depths less than 6 inches, the protective material is too easily displaced or compacted.)
NOTE: Do not install home playground equipment over concrete, asphalt, or any other hard surface. A fall onto a hard surface
can result in serious injury to the equipment user. Grass and dirt are not considered protective surfacing because wear and
environmental factors can reduce their shock absorbing effectiveness. Carpeting and thin mats are not adequate protective
surfacing. Ground level equipment -- such as a sandbox, activity wall, playhouse or other equipment that has no elevated play
surface -- does not need any protective surfacing.
• Use containment, such as digging out around the perimeter and/or lining the perimeter with landscape edging. Don’t forget to
account for water drainage.
• Periodically rake, check and maintain the depth of the loose-fill surfacing material. Marking the correct depth on the play
equipment support posts will help you to see when the material has settled and needs to be raked and or replenished. Be sure to
rake and evenly redistribute the surfacing in heavily used areas.
• Do not install loose fill surfacing over hard surfaces such as concrete or asphalt.
Poured-In-Place Surfaces or Pre-Manufactured Rubber Tiles
You may be interested in using surfacing other than loose-fill materials - like rubber tiles or poured-in-place surfaces.
• Installations of these surfaces generally require a professional and are not “do-it yourself” projects.
• Review surface specifications before purchasing this type of surfacing. Ask the installer/manufacturer for a report showing that
the product has been tested to the following safety standard: ASTM F1292 Standard Specification for Impact Attenuation of
Surfacing Materials within the Use Zone of Playground Equipment. This report should show the specific height for which the
surface is intended to protect against serious head injury. This height should be equal to or greater than the fall height - vertical
distance between a designated play surface (elevated surface for standing, sitting, or climbing) and the protective surfacing
below - of your play equipment.
• Check the protective surfacing frequently for wear.
Placement
Proper placement and maintenance of protective surfacing is essential. Refer to diagram on front cover. Be sure to;
• Extend surfacing at least 2m from the equipment in all directions.
• For to-fro swings, extend protective surfacing in front of and behind the swing to a distance equal to twice the height of the top bar
from which the swing is suspended.
• For tire swings, extend surfacing in a circle whose radius is equal to the height of the suspending chain or rope, plus 6 feet in all
directions.
From the CPSC Outdoor Home Playground Safety Handbook. At http://www.playgroundregs.com/resources/CPSC%20324.pdf
Protective Surfacing - Reducing Risk of Serious Head Injury From Falls.
2H 2H
H
Denotes Use Zone with Protective Surfacing
Use Zone for Single-Axis Swings
6 ft.
6 ft.
6 ft.
6 ft.
Denotes Use Zone with Protective Surfacing
Use Zone for Multi-Axis Swings
6 ft. 6 ft.
6 ft.
L

4
Instructions for Proper Maintenance
HARDWARE:
Check metal parts for rust. If found,
sand and repaint using a non-lead
paint complying with 16 CFR 1303.
Inspect and tighten all hardware. On
wood assemblies DO NOT OVER-
TIGHTEN as to cause crushing and
splintering of wood.
Check for sharp edges or protruding screw threads, add
washers if required.
SHOCK ABSORBING SURFACING:
Check for foreign objects. Rake and check depth of loose
fill protective surfacing materials to prevent compaction
and maintain appropriate depth. Replace as necessary.
(See Protective Surfacing, page 3)
GROUND STAKES (ANCHORS):
Check for looseness, damage or deterioration. Should
firmly anchor unit to ground during use. Re-secure and
or replace, if necessary.
SWING HANGERS:
Check that bolts are secure and tight. Quick clips should
be completely closed and threaded clips screwed tight.
If squeaking occurs lubricate bushings with oil or WD-40®.
SWINGS, ROPES AND RIDES:
Reinstall if removed during cold season. Check all
moving parts including swing seats, ropes, chains and
attachments for wear, rust and other deterioration.
Replace as needed.
Check that ropes are tight, secure at both ends and
cannot loop back as to create an entrapment.
WOOD PARTS:
Check all wood members for deterioration, structural
damage and splintering. Sand down splinters and replace
deteriorated wood members. As with all wood, some
checking and small cracks in grain is normal.
Unprotected, they will appear weathered over time.
Periodic application of an exterior water repellent or stain
(water-based) will help improve appearance and life.
Your KidKraft Play System is designed and constructed of quality materials with your child’s safety in mind. As with all outdoor
products used by children, it will weather and wear. To maximize the enjoyment, safety and life of your Play Set, it is important
that you, the owner, properly maintain it.
Check the following at the beginning of the play season:
HARDWARE:
Inspect for tightness. Must be firmly against, but not
crushing the wood. DO NOT OVER-TIGHTEN.
This will cause splintering of wood.
Check for sharp edges or protruding screw threads.
Add washers if required.
SHOCK ABSORBING SURFACING:
Rake and check depth of loose fill protective surfacing
materials to prevent compaction and maintain appropriate
depth. Replace as necessary.
(See Protective Surfacing, page 3)
Check twice a month during play season:
SWING HANGERS:
Check that they are secure and orientated correctly. Hook
should rotate freely and perpendicular to support beam.
If squeaking occurs lubricate bushings with oil or WD-40®.
SWINGS AND RIDES:
Check swing seats, all ropes, chains and attachments for
fraying, wear, excessive corrosion or damage.
Replace if structurally damaged or deteriorated.
Check once a month during play season:
SWINGS AND RIDES:
To prolong their life, remove swings and store inside
when outside temperature is below 32°F/0°C. Below
freezing, plastic parts may become more brittle.
SHOCK ABSORBING SURFACING:
Rake and check depth of loose fill protective surfacing
materials to prevent compaction and maintain appropriate
depth. Replace as necessary.
(See Protective Surfacing, page 3)
Check at the end of the play season:
If you dispose of your play set: Please disassemble and dispose of your unit so that it does not create any unreasonable hazards
at the time it is discarded. Be sure to follow your local waste ordinances.
Use an extra
Flat Washer
If Bolt protrudes
beyond T-Nut

5
About Our Wood
KidKraft Premium Play Systems uses only premium playset lumber, ensuring the safest product for your children’s use. Although we
take great care in selecting the best quality lumber available, wood is still a product of nature and susceptible
to weathering which can change the appearance of your set.
What causes weathering? Does it affect the strength of my Play System?
One of the main reasons for weathering is the effects of water (moisture); the moisture content of the wood at the surface is
different than the interior of the wood. As the climate changes, moisture moves in or out of the wood, causing tension which can
result in checking and or warping. You can expect the following due to weathering. These changes will not affect the strength of
the product:
1. Checking is surface cracks in the wood along the grain. A post (4” x 4”)will experience more checking than a board (1” x 4”)
because the surface and interiormoisture content will vary more widely than in thinner wood.
2. Warping results from any distortion (twisting, cupping) from the original plane ofthe board and often happens from rapid
wettingand drying of the wood.
3. Fading happens as a natural change in the wood coloras it is exposed tosun-light and will turn a grey over time.
How can I reduce the amount of weathering to my Play System?
At the factory we have coated the wood with a water repellent or stain. This coating decreases the amount of water absorption
during rain or snow thus decreasing the tension in the wood. Sunlight will break down the coating, so we recommend applying a
water repellent or stain on a yearly basis (see your local stain and paint supplier for a recommended product).
Most weathering is just the normal result of nature and will not affect safe play and enjoyment for your child. However if you are
concerned that a part has experienced a severe weathering problem please call our consumer relations department for further assistance.
Complete and mail registration card to receive important product notifications and assure prompt
warranty service.
5 Year Limited Warranty
KidKraft warrants that this product is free from defect in materials and workmanship for a period of one
year from the original date of purchase. In addition, lumber is warranted for 5 years against structural
failure due to rot and insect damage. All other parts, such as hardware, swings, rides, accessories, and
slides carry a one-year warranty only.
This warranty applies to the original owner and registrant and is non-transferable.
Regular maintenance is required to assure the integrity of your Play System. This warranty does not
cover any inspection cost.
This Limited Warranty does not cover:
•Labor for replacement of any defective item(s);
•Incidental orconsequential damages;
•Cosmetic defects whichdo not affect performance or integrity;
•Vandalism; improper use or installation; acts of nature;
•Minortwisting, warping, checking,or any other natural occurring properties of wood that do not
affect performance or integrity.
KidKraft products have been designed for safety and quality. Any modifications made to the original
product could damage the structural integrity of the unit leading to failure and possible injury.
Kidkraft cannot assume any responsibility for modified products. Furthermore, modification voids
any and all warranties.
This product is warranted for RESIDENTIAL USE ONLY. Under no circumstance should a
KidKraft Play System be used in public settings such as schools, churches, playgrounds, parks, day
cares and the like. Such use may lead to product failure and potential injury. Any and all public use
will void this warranty.
KidKraft disclaims all other representations and warranties of any kind, express or implied.
This Warranty gives you specific legal rights. You may have otherrights as well which vary from state to state or
province to province. This warranty excludes all consequential damages, however, some states do notallow the
limitation or exclusion ofconsequential damages, andtherefore this limitation may not apply to you.

6
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio /TV technician for help.
Note: Changes or modications not expressly approved by the manufacturer responsible for compliance
could void the user’s authority to operate the equipment.
Please retain the information on this pack for future reference.
- Batteries should always be installed and changed under adult supervision.
- Non-Rechargeable batteries are not to be recharged.
- Rechargeable batteries are only to be charged under adult supervision.
- Only batteries of the same equivalent type as recommended are to be used.
- Batteries are to be inserted with the correct polarity.
- Exhausted batteries are to be removed from the toy and disposed of properly.
- The supply terminals are not to be short circuited.
- Different types of batteries or new and used batteries are not to be mixed.
- DO NOT mix alkaline, standard (carbon-zinc) or rechargeable batteries.
- Be sure to insert new batteries with positive (+) side up.
- Rechargeable batteries are to be removed from the toy before being charged.
- EU Regulations require exhausted batteries to be separately collected so that they can be treated using
the best available recovery and recycling techniques. This will minimize the impact on the environment and
human health from soil and water contamination by any hazardous substances, decrease the resources
required to make new products and avoid using up landll space.
- Batteries or battery packs must be recycled or disposed of properly. When the batteries in this product
have reached the end of their useful life, they should not be disposed of with other household waste.
- Please do your part by keeping waste batteries out of the municipal waste stream!
Battery Instruction and Warranty

7
Part Identication Key
On each page, you will nd the parts
and quantities required to complete
the assembly step illustrated on that
page. Here is a sample.
Key Number: The rst two digits
represent the step number. The third
digit represents the piece. Note that if
the part is used in multiple steps then
the number only reects the rst step
it is used in.
Symbols
Throughout these instructions symbols are provided as important reminders for proper and safe assembly.
Proper Hardware Assembly
Lag screws require drilling pilot
holes to avoid splitting wood. Only a
at washer is required. For ease of
installation liquid soap can be used
on all lag-type screws.
For bolts, tap T-Nut into hole with
hammer. Insert the hex bolt through
lock washer rst then at washer
then hole. Because the assemblies
need to be squared do not completely
tighten until instructed. Pay close
attention to diameter of the bolts.
5/16” is slightly larger than 1/4”.
Note: Wafer head bolts with blue lock
tight or a bolt with a Ny-Lok nut do
NOT require a lock washer.
Once the assembly is tightened, watch for exposed
threads. If a thread protrudes from the T-Nut, remove
the bolt and add washers to eliminate this condition.
Extra washers have been provided for this purpose.
This identies information that requires
special attention. Improper assembly could
lead to an unsafe or dangerous condition.
Where this is shown, 2 or 3
people are required to safely
complete the step. To avoid
injury or damage to the
assembly make sure to
get help!
Check that assembly is square
before tightening bolts.
Use a measuring tape to
assure proper location.
Check that set or assembly is properly level
before proceeding.
Pre-drill a pilot hole
before fastening screw
or lag to prevent
splitting of wood.
This indicates time to tighten bolts, but
not too tight! Do not crush the wood.
This may create splinters and cause
structural damage.
Use
Help
Use
Help
Measure
Distance
Square
Assembly
Use
Level
Pre-drill 1/8” & 3/16” Bit
Tighten
Bolts
No Yes
CAUTION – Protrusion Hazard
Keys to Assembly Success
Tools Required
• Tape Measure
• Carpenters Level
• Carpenters Square
• Claw Hammer
• Standard or Cordless Drill
• #1, #2 & #3 Phillips
or Robertson Bits
or Screwdriver
• Ratchet with extension
(1/2” & 9/16” sockets)
• Open End Wrench
(7/16”, 1/2” & 9/16”)
• Adjustable Wrench
• 1/8” & 3/16” Drill Bits
• Pencil
• 3/16” Hex Key
• 8’ Step Ladder
• Safety Glasses
• Adult Helpers
Quantity Key Number Part Description,
Part Size
2X 012 Post 2 x 4 x 83”
Use an extra
Flat W asher
If Bolt protrudes
beyond T-Nut
Lag Screw
Flat Washer
Lag Assembly
Before mounting Lag Screw,
use factory drilled holes as
guides to drill 1/8” pilot holes
Hex Bolt Bolt Assembly
T-Nut
(Hammer into place)
Do not crush wood!
Lock
Washer
Flat
Washer

8
Key Number: The rst two digits represent the step
number. The third digit represents the order in which
the part is listed in the step.
Note that if the part is used in multiple steps then
the key number only reects the rst step it is used in.
Part Quantity Key Number
Order Listed
(The order the part is
listed in step 1)
Part Description Part Size
2X 012 Post 2 x 4 x 83”
Your Key To Quick Assembly
SAVE TIME - TIP #1:
Open each box with wood parts and look for the Key Number
stamped on the end of the wood part (see chart below). Sort
each wood part into the different assembly steps.
SAVE TIME - TIP #2:
In addition to the key number stamp, you can also identify
the wood parts by using the Parts Identication pages in the
manual or the Parts Identication weather resistant poster.
HARDWARE:
The majority of each hardware part comes packed in a separate bag
so you do not need to sort the hardware. Each assembly step indicates
which hardware (bolt, screw, washer etc.) you will require to complete
the step.
SORTING WOOD PARTS INTO
EACH ASSEMBLY STEP WILL
SAVE TIME!
01 2
Step Number
(This is Step 1)
Step Step Step

9
021
x2
2x
041
2x
023
022
x2
024
x3
17x
051
062
x4
2x
072
4x
061
043
073
x2
075
x2
4x
082
10x
081
091
x2
2x
092
Hidden
112 111 113
x3
114
Hidden
131
071
Superfold Roof
Mailbox
Door Hardware
Slide 40" High Rail EN71
KidKraft Plaque
KidKraft ID Plaque
074
x2
Door Bell
132
Hidden
2x
042
Flat Panel Bracket
2x Corner Brace

10
1 inch = 25.4mm
SOLO)WAVE DESIGN HARDWARE
For example:
BOLT LENGTH 4½ (4.5) inches long
114mm long
1 inch = 25.4mm
25.4mm
4.5 inches x
DIAMETER CONVERSION
LENGTH CONVERSION
=
BOLT DIAMETER 5/16 (0.31) inches 0.31 inches x 25.4mm = 8mm
For example:
HARDWARE LENGTH CHART
inches vs millimetres
6 152
5½ 140
5 127
4½ 114
4 102
3½ 89
3 76
2½ 64
2 51
1½ 38 1¼ 32
1-1/8 29
1 25.4
7/8 22 3/4 19 1/2 12.7
1/4" (6mm) Flat Washer
1/4" (6mm) Lock Washer
1/4"(0.25) = 6mm Hex Bolt
1/4" (6mm) T-Nut
5/16"(.31) = 8mm Lag Screw
5/16" (8mm) Flat Washer
1/4"(0.25) = 6mm Lag Screw
1/4" (6mm) Flat Washer
5/16" (8mm) Flat Washer
5/16" (8mm) Lock Washer
5/16"(.31) = 8mm Hex Bolt
5/16" (8mm) T-Nut
3/8"(.38) = 9.5mm Lag Screw
3/8" (9.5mm) Flat Washer
KIDKRAFT HARDWARE

11
(Reduced Part Size) Part Identification
2pc. - 021 - 5/8 x 4-1/2 x 76-7/8" (15.9 x 114.3 x 1952.6mm) - Lower Front Back - Box 2 - 3569327
2pc. - 041 - 5/8 x 4-1/2 x 47-3/4" (15.9 x 114.3 x 1213.4mm) - Lower Side - Box 2 - 3569328
2pc. - 022 - 1-1/4 x 3 x 38" (31.8 x 76.2 x 964.5mm) - Upright Short - Box 2 - 3569329
2pc. - 042 - 1-1/4 x 3 x 44" (31.8 x 76.2 x 1118mm) - End Floor Support - Box 2 - 3569330
3pc. - 024 - 1-1/4 x 3 x 74-3/8" (31.8 x 76.2 x 1889mm) - Floor Support Long - Box 2 - 3569331
17pc. - 051 - 5/8 x 4-1/2 x 44" (15.9 x 114.3 x 1118mm) - Floor Board - Box 2 - 3739332
2pc. - 074 - 5/8 x 3 x 61" (15.9 x 76.2 x 1549.4mm) - Upright Center - Box 2 - 3569333
2pc. - 075 - 5/8 x 3 x 4-1/2" (15.9 x 76.2 x 114.3mm) - Upright Block - Box 1 - 3569334
2pc. - 023 - 1-1/4 x 3 x 61" (31.8 x 76.2 x 1549.4mm) - Upright Long - Box 2 - 3569335
1pc. - 043 - 1-1/4 x 3 x 46-1/2" (31.8 x 76.2 x 1181.6mm) - SL Barrier Top - Box 2 - 3569336
2pc. - 072 - 1-1/4 x 3 x 32-7/8" (31.8 x 76.2 x 835mm) - Side BarrierTop - Box 2 - 3569337
10pc. - 081 - 5/8 x 3 x 27-5/8" (15.9 x 76.2 x 701.7mm) - SL Barrier - Box 2 - 3569338
4pc. - 082 - 1-1/4 x 3 x 27-5/8" (31.8 x 76.2 x 701.7mm) - End Barrier - Box 2 - 3569339
1pc. - 114 - 5/8 x 3-1/4 x 20-3/4" (15.9 x 82.6 x 527mm) - Ladder Gap - Box 2 - 3569340
1pc. -
132 - 1 x 2-1/2 x 5" (23.8 x 63.5 x 127mm) - Door Stop - Box 1 - 3569341
4pc. - 061 - 1-1/4 x 3 x 13-3/8" (31.8 x 76.2 x 340mm) - Gusset Long - Box 2 - 3569342
4pc. - 062 - 1-1/4 x 3 x 11-3/4" (31.8 x 76.2 x 300mm) - Gusset Short - Box 2 - 3569343
2pc. - 091
2pc. - 092
- 1 x 1 x 44" (25.4 x 25.4 x 1117.6mm) - Side Wall Soffit - Box 2 - 3569344
- 1 x 1 x 41-7/8" (25.4 x 25.4 x 1064.8mm) - End Wall Soffit - Box 1- 3569345

12
1pc. - 071 - 8 x 22 x 43" (203.4 x 558.8 x 1092.2mm) - Panel Assembly - Box 1 - 378569213
(Reduced Part Size) Part Identification
1pc. - 111 - 1-3/8 x 3 x 39-7/8" (34.9 x 76.2 x 1013mm) - Right Access - Box 1 - 3739346
3pc. - 113 - 1 x 3-1/4 x 19-1/4" (23.8 x 82.6 x 488.8mm) - Tread - Box 1 - 3739347
1pc. - 112 - 1-3/8 x 3 x 39-7/8" (34.9 x 76.2 x 1013mm) - Left Access - Box 1 - 3739348
2pc. - 073 - 5/8 x 3 x 37-7/8" (15.9 x 76.2 x 963mm) - Center Tie - Box 2- 3569349
1pc. -
131 - 1 x 16-3/4 x 38-3/8" (25.4 x 425.5 x 974.3mm) - Door - Box 1 - 37739212

13
1x
- Mailbox (3321910)
1x
- Door Bell (3321946)
1x
- Bracket Set (3329060)
1x
- Flat Panel Bracket
(9206733)
1x
- Door Hardware (3200710)
1x
- Mailbox 2 Door
(9321526)
1x
- Mailbox Flag Half
(9321923A)
3x
- #6 x 9 mm
Self Tapping Screw
(52042902)
1x
1x
- Rural Mailbox Flag
(9320327)
1x
- Mailbox 2 Bottom
(9330522)
1x
- Doorbell 2
(9320545)
1x
- Doorbell Trim
(9321917)
2x - Door Handle
(9207711)
2x - Door Hinge Assembly
(9207712)
1x
- Magnetic Catch Assembly
(9207713)
(Reduced Part Size) Part Identification
1x
- Superfold Roof
(P-U-4604-SBT)
-Slide 40" High Rail EN71
(3311940)
1x
2x
- Corner Bracket
(9206770)
-KidKraft ID Plaque
(9320370)
1x
-KidKraft Logo Plaque
(P-U-4825)
1x
- Mailbox Other Half
(9321923B)
1x - Rebar GroundStake (6 Pk)
(3200318)

14
Hardware Identification (Actual Size)
2pc. S15
2pc. LS2 - Lag Screw 1/4 x 2-1/2" (6mm x 64mm) - (52213222)
6pc. H2
22pc. S0 - Truss Head Screw #8 x 7/8" (22mm)
- (52933505)
44pc. S3
12pc. S4
202pc. S20
20pc. S13
10pc. S7
42pc. S11
5pc. S10
2pc. S18
10pc. S37
- Wood Screw #8 x 1-3/8” (35mm) - (52043516)
6pc. H3
2pc. H8
36pc. FW1 - 1/4" (6mm) Flat Washer - (51103200)
18pc. LW1 - 1/4" (6mm) Washer Lock - (51303200)
18pc. TN1
- 1/4" (6mm) T - Nut - (54503200)
- Wood Screw #8 x 2-1/2" (64mm) - (52043522)
- Wood Screw #8 x 3" (76mm) - (52043530)
-Pan Screw#12 x 2" (51mm) - (52433620)
-Pan Screw#8 x 1" (25mm) - (52433510)
- Wood Screw #8 x 2" (51mm) - (52043520)
- Pan Screw #6 x 5/8" (16mm) 52413908)
- Wood Screw #8 x 1-3/4" (44mm) - (52043513)
-Wood Screw #6 x 1" (25mm) - (52013910)
- Pan Screw #7 x 5/8" (16mm) - (52433009)
- Hex Bolt 1/4 x 2" (6mm x 51mm) - (53703220)
- Hex Bolt 1/4 x 2-1/2" (6mm x 64mm) - (53703222)
- Hex Bolt 1/4 x 4-1/4" (6mm x 108mm) - (53703241)
4pc. H15
- Hex Bolt 1/4 x 3-3/4" (6mm x 95mm) - (53702233)
1pc. D4 - #2 Robertson Driver Bit- (9200014)

15
STOP STOPSTOP STOP
Step 1: Inventory Parts - Read This Before Starting Assembly
• Please refer to Page 6 for proper hardware assembly.
• Each step indicates which bolts and/or screws you will need for assembly, as well as
any at washers, lock washers, t-nuts or lock nuts.
A. This is the time for you to inventory all your hardware, wood and accessories,
referencing the parts identication sheets. This will assist you with your assembly.
• The wood pieces will have the four digit key number stamped on the ends of the
boards. The wood pieces are referenced throughout the instructions with this number.
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 4)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 5)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 6)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 1)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 2)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 3)
MODEL NUMBER: F29060
TRACKING NUMBER (from ID Plaque):
B. If there are any missing or damaged pieces or you need assistance with
assembly please contact the consumer relations department directly. Call us
before going back to the store.
C. Read the assembly manual completely, paying special attention to ANSI warnings;
notes; and safety/maintenance information.
D. Before you discard your cartons ll out the form below.
• The carton I.D. stamp is located on the end of each carton.The tracking number is
located on the KidKraft ID Plaque (9320370).
• Please retain this information for future reference. You will need this information if you
contact the Consumer Relations Department.
[phone]
[email protected]
For online parts replacement visit
https://parts.kidkraft.eu/
1.800.933.0771 or 972.385.0100
[email protected]
[email protected]
For online parts replacement visit
https://parts.kidkraft.com/

1 x Lower Front Back 5/8 x 4-1/2 x 76-7/8”
1 x Upright Short 1-1/4 x 3 x 38”
1 x Upright Long 1-1/4 x 3 x 61”
1 x Floor Support Long 1-1/4 x 3 x 74-3/8”
021
023
022
024
Note: It is important to note hole orientation for the following step.
A: Place (021) Lower Front Back so that one end is over (023) Upright Long and the other end is over (022)
Upright Short. Attach each end using 1 (H2) 1/4 x 2” Hex Bolt (with lock washer, at washer and t-nut) and 1
(S20) #8 x 1-3/8” Wood Screw making sure to note hole orientation. (g. 2.1 and g. 2.3)
B: Place (024) Floor Support Long so that one end is under the middle holes on (023) Upright Long and the other
end is under the end of (022) Upright Short. Attach each end using 1 (H3) 1/4 x 2- 1/2” Hex Bolt (with lock washer, at
washer and t-nut). Check to make sure that assembly is square. (g. 2.1 and g. 2.2)
16
Wood Parts Hardware
Step 2: Back Wall Assembly
2 x 1/4 x 2” Hex Bolts
(1/4” lock washer, 1/4” at washer, 1/4” t-nut)
2 x #8 x 1-3/8” Wood Screw
2 x 1/4 x 2-1/2” Hex Bolt
(1/4” lock washer, 1/4” at washer, 1/4” t-nut)
H2
H3
S20
023
024
021
022
S20
S20
H2
H3
Fig. 2.1
1/4” Flat
Washer
1/4” Flat
Washer
1/4” Lock
Washer
1/4” Lock
Washer 1/4” T-Nut
1/4” T-Nut
1/4” T-Nut
S20
H2
Fig. 2.3 1/4” Flat
Washer
1/4” Lock
Washer
1/4” T-Nut
H3
Fig. 2.2
1/4” Flat
Washer
1/4” Lock
Washer
1/4” T-Nut
022
022
024
021
Note hole orientation

1 x Lower Front Back 5/8 x 4-1/2 x 76-7/8”
1 x Upright Short 1-1/4 x 3 x 38”
1 x Upright Long 1-1/4 x 3 x 61”
1 x Floor Support Long 1-1/4 x 3 x 74-3/8”
021
023
022
024
Wood Parts
Note: It is important to note hole orientation for the following step.
A: Refer to Step 2 but placing (023) Upright Long and (022) Upright Short on the opposite ends of the (021)
Lower Front Back. Attach each end using 1 (H2) 1/4 x 2” Hex Bolt (with lock washer, at washer and t-nut) and 1
(S20) #8 x 1-3/8” Wood Screw making sure to note hole orientation. (g. 3.1 and g. 3.2)
B: Place (024) Floor Support Long so that one end is under the middle holes on (023) Upright Long and the other
end is under the end of (022) Upright Short. Attach each end using 1 (H3) 1/4 x 2- 1/2” Hex Bolt (with lock washer, at
washer and t-nut). Check to make sure that assembly is square. (g. 3.1 and g. 3.3)
17
Step 3: Front Wall Assembly
021
021
024
023
022
022
024
S20
S20
S20
H2
H2 H3
H3
1/4” Lock Washer
1/4” Lock Washer
1/4” Lock Washer
1/4” Lock Washer
1/4” T-Nut
1/4” T-Nut
1/4” T-Nut
1/4” T-Nut
1/4” T-Nut
1/4” Flat Washer
1/4” Flat Washer
1/4” Flat Washer
Note hole orientation
1/4” Flat Washer
022
Hardware
2 x 1/4 x 2” Hex Bolts
(1/4” lock washer, 1/4” at washer, 1/4” t-nut)
2 x #8 x 1-3/8” Wood Screw
2 x 1/4 x 2-1/2” Hex Bolt
(1/4” lock washer, 1/4” at washer, 1/4” t-nut)
H2
H3
S20
Fig. 3.1
Fig. 3.2
Fig. 3.3

A: With a helper hold Front and Back Wall Assemblies in position as shown in g. 4.1.
B: Place 1 (041) Lower Side across the bottom of each end and attach using 2 (H15) 1/4 x 3- 3/4” Hex Bolts (with
lock washer, at washer and t-nut) and 2 (S20) #8 x 1 -3/8” Wood Screws per board making sure that the assembly is
square. (g. 4.1 and g. 4.2)
18
Step 4: Side Wall Assembly
Part 1
Fig. 4.1
Fig. 4.2
Front Wall Assembly
Back Wall Assembly
S20
H15
1/4” Lock
Washer
1/4”
T-Nut
1/4” Flat
Washer
041
041
041
023
022
Hardware
4 x 1/4 x 3-3/4” Hex Bolts
(1/4” lock washer, 1/4” at washer, 1/4” t-nut)
4 x #8 x 1-3/8” Wood Screw
H15
S20
2 x Lower Side 5/8 x 4-1/2 x 47-3/4”
041
Wood Parts
x 2 per board
x 2 per board

C: Place 1 (042) End Floor Support at each end of the assembly so they are ush to the (024) Floor Support
Longs. Attach each (042) End Floor Support using 6 (S3) #8 x 2 -1/2” Wood Screws per board as shown in g.
4.3 and 4.5.
D: Place 1 (024) Floor Support Long lengthwise through the center of the assembly so each end lines up with the pre-
drilled holes in (042) End Floor Supports. Attach (024) Floor Support Long using 4 (S3) #8 x 2 -1/2” Wood Screws. (g.
4.3 and g. 4.4)
19
Step 4: Side Wall Assembly
Part 2
Hardware
16 x #8 x 2-1/2” Wood Screw
S3
Fig. 4.3
024
023
042
022
Flush
Flush
042
Fig. 4.5
042
024
S3
023
Fig. 4.4
S3
Flush
042
024
1 x Floor Support Long 1-1/4 x 3 x 74-3/8”
2 x End Floor Support 1-1/4 x 3 x 44”
042
Wood Parts
024
022
x 4
x 6 per board

E: Attach (043) SL Barrier Top to (023) Upright Longs using 2 (H8) 1/4 x 4- 1/4” Hex Bolts (with lock washer, at
washer and t-nut) making sure that all boards are ush at the top. (g. 4.6 and g. 4.7)
Flush
x 2
Flush
20
Step 4: Side Wall Assembly
Part 3
023
043
043
023
H8
1/4” Lock
Washer
1/4” T-Nut
Flush
1/4” Flat
Washer
Fig. 4.7
Fig. 4.6
Hardware
2 x 1/4 x 4-1/4” Hex Bolts
(with at washer, lock washer and t-nut)
H8
1 x SL Barrier Top 1-1/4 x 3 x 46-1/2”
Wood Parts
043
H8
H8