KidKraft RIDGEVIEW DELUXE CLUBHOUSE PLAY SYSTEM User manual

INSTALLATION AND OPERATING INSTRUCTIONS
10-14 Hrs
To reduce the risk of serious injury or death, you must read and
follow these instructions. Keep and refer to these instructions often
and give them to any future owner of this play system. Manufacturer contact information provided below.
OBSTACLE FREE SAFETY ZONE - 26’5” x 26’ 6” area requires Protective Surfacing. See page 3.
MAXIMUM VERTICAL FALL HEIGHT - 6’5”
CAPACITY - 9 Users Maximum, Ages 3to 10; Weight Limit 110 lbs. (49.9 kg) per child.
RESIDENTIAL HOME USE ONLY. Not intended for public areas such as schools, churches, nurseries, day cares or parks.
Warning. Only for demestic use.
Two person
assembly
WARNING
14' 5"
13’ 6" 26' 6"
26' 5"
9400855 Rev 03/30/2020
Table of Contents
Warnings and Safe Play Instructions. . . . . . . . . . . . . . . pg. 2
Protective Surfacing Guidelines. . . . . . . . . . . . . . . . . . . pg. 3
Instructions for Proper Maintenance ...............pg. 4
About Our Wood – Limited Warranty ............ pg. 5-6
Keys to Assembly Success ......................pg. 7
Metric Conversion Sheets ..................... pg. 8-9
Part ID......................................pg. 10
Installation of I.D./Warning Plaque ............Final Step
RIDGEVIEW DELUXE CLUBHOUSE
PLAY SYSTEM – F270855
KidKraft, Inc.
4630 Olin Road
Dallas, Texas 75244 USA
[email protected]
[email protected]
1.800.933.0771
972.385.0100
For online parts replacement visit
https://parts.kidkraft.com/
KidKraft Netherlands BV
Olympisch Stadion 8
1076 DE Amsterdam
The Netherlands
[email protected]
[phone] M-F from 09:00 to 17:30
(GMT+1)
For online parts replacement visit
https://parts.kidkraft.eu/

2
Warnings and Safe Play Instructions
CONTINUOUS ADULT SUPERVISION REQUIRED. Most serious injuries and deaths on playground equipment have occurred
while children were unsupervised! Our products are designed to meet mandatory and voluntary safety standards. Complying
with all warnings and recommendations in these instructions will reduce the risk of serious or fatal injury to children using
this play system. Go over the warnings and safe play instructions regularly with your children and make certain that they
understand and follow them. Remember on-site adult supervision is required for children of all ages.
SERIOUS HEAD INJURY HAZARD
Installation over concrete, asphalt, dirt, grass, carpet
and other hard surface creates a risk of serious injury
or death from falls to the ground. Install and maintain
shock absorbing material under and around play-set as
recommended on page 3 of these instructions.
COLLISION HAZARD
Place play-set on level ground at least 2m from any
obstruction such as a garage or house, fences, poles,
trees, sidewalks, walls, landscape timbers, rocks,
pavement, planters, garden borders, overhanging
branches, laundry lines, and electrical wires. (See
OBSTACLE FREE SAFETY ZONE on cover)
CHOKING HAZARD/SHARP EDGES & POINTS
Adult assembly required. This product contains small
parts and parts with sharp edges and points. Keep parts
away from children until fully assembled.
WARNING LABEL
Owners shall be responsible for maintaining the legibility
of the warning labels.
STRANGULATION HAZARD
,senilsehtolc,seporhtiwyalpotnerdlihcwollaREVEN•
pet leashes, cables, chains or cord-like items when using
this play-set or to attach these items to play-set.
ponchos, hoods, scarves, capes, necklaces, items with
draw-strings, cords or ties when using this play-set.
stemlehtropsroekibraewotnerdlihcwollaREVEN•
when using this play-set.
Failure to prohibit these items, even helmets with chin
straps, increases the risk of serious injury and death to
children from entanglement and strangulation.
TIP OVER HAZARD
Choose a level location for the equipment. This can reduce
the likelihood of the play set tipping over and loose- ll
surfacing materials washing away during heavy rains.
D
Never add extra length to chain or rope. The chains or ropes
provided are the maximum length designed for the swinging
element(s).
O NOT allow children to play on the play-set until the
assembly is complete and the unit is properly anchored.
WARNING
eeS.tes-yalpruoyfosnoitatimilyticapacevresbO
front cover.
gnisolcnetoofllufdnagnittllewhtiwnerdlihcsserD
footwear.
retnecehtnithgiewllufriehthtiwtisotnerdlihchcaeT
of the swing seat to prevent erratic swing motion or
falling off.
,gnissim;doowdekcarcronekorb,deretnilpsrofkcehC
loose, or sharp edged hardware. Replace, tighten and or
sand smooth as required prior to playing.
niahc,sreddalepor,seporgnibmilcdednepsustahtyfireV
or cable are secured at both ends and cannot be looped
back on itself as to create an entanglement hazard.
rehtodnaedilsehtkcehc,syadtohrodnaynnusnO
plastic rides to assure that they are not very hot as to
cause burns. Cool hot slide and rides with water and wipe
dry prior to using.
raewtoofleehroeotneporaewotnerdlihcwollatonoD
like sandals, ip– ops or clogs.
dniheb,neewteb,tnorfni,klawotnerdlihcwollatonoD
or close to moving rides.
poolroseporrosniahcgniwstsiwtnerdlihcteltonoD
them over the top support bar. This may reduce the
strength of the chain or rope and cause premature failure.
.noitomnierayehtelihwsedirffotegnerdlihcteltonoD
.tewsitinehwtnempiuqenognibmilctimreptonoD
anitnempiuqefoesuroyalphguortimreptonoD
manner for which it was not intended. Standing on or
jumping from the roof, elevated platforms, swings,
climbers, ladders or slide can be dangerous.
.staesrosedirytpmegniwsotnerdlihcwollatonoD
rotsrdaehedilsnwodogotnerdlihcwollatonoD
run up slide.
WARNING – Safe Play Instructions
Orientate slide such that it gets the least amount of exposure
to the sun.

3
One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing
protective surfacing under and around your play equipment. The protective surfacing should be applied to a depth that is suitable
for the equipment height in accordance with ASTM F1292. There are different types of surfacing to choose from; whichever
product you select, follow these guidelines:
Loose-Fill Materials
• M
aintain a minimum depth of 9 inches (23 cm) of loose-fill materials such as wood mulch/chips, engineered wood fiber (EWF), or
shredded/recycled rubber mulch for equipment up to 8 feet (2.45 m) high; and 9 inches (23 cm) of sand or pea gravel for equipment up to 5 feet (1.5 m)
high. NOTE: An initial fill level of 12 inches (31 cm) will compress to about a 9-inch (23 cm) depth of surfacing over time. The surfacing will also
compact, displace, and settle, and should be periodically raked and refilled to maintain at least a 9-inch (23 cm) depth.
• U
se a minimum of 6 inches (16 cm) of protective surfacing for play equipment less than 4 feet (1.22 m) in height. If maintained properly, this
should be adequate. (At depths less than 6 inches (16 cm), the protective material is too easily displaced or compacted.)
NOTE: Do not install home playground equipment over concrete, asphalt, or any other hard surface. A fall onto a hard surface
can result in serious injury to the equipment user. Grass and dirt are not considered protective surfacing because wear and
environmental factors can reduce their shock absorbing effectiveness. Carpeting and thin mats are not adequate protective
surfacing. Ground level equipment -- such as a sandbox, activity wall, playhouse or other equipment that has no elevated play
surface-- does not need any protective surfacing.
• Use containment, such as digging out around the perimeter and/or lining the perimeter with landscape edging. Don’t forget to
account for water drainage.
• Periodically rake, check and maintain the depth of the loose-fill surfacing material. Marking the correct depth on the play
equipment support posts will help you to see when the material has settled and needs to be raked and or replenished. Be sure to
rake and evenly redistribute the surfacing in heavily used areas.
• Do not install loose fillsurfacing over hard surfaces such as concrete or asphalt.
Poured-In-Place Surfaces or Pre-Manufactured Rubber Tiles
You may be interested in using surfacing other than loose-fill materials - like rubber tiles or poured-in-placesurfaces.
• Installations of these surfaces generally require a professional and are not “do-it yourself ” projects.
• Review surfacespecifications before purchasing this type of surfacing. Ask the installer/manufacturer for a report showing that
the product has been tested to the following safety standard: ASTM F1292 Standard Specification for Impact Attenuation of Surfacing
Materials within the Use Zone of Playground Equipment. This report should show the specific height for which the surfaceis intended
to protect against serious head injury. This height should be equal to or greater than the fall height - vertical distance between a
designated play surface (elevated surface for standing, sitting, or climbing) and the protective surfacing below - of your play equipment.
• Check the protective surfacing frequently for wear.
Placement
Proper placement and maintenance of protective surfacing is essential. Refer to diagram on front cover. Be sure to;
• Extend surfacing at least 6 feet (1.8 m) from the equipment in all directions.
• For to-fro swings, extend protective surfacing in front of and behind the swing to a distance equal to twice the height of the top
bar from which the swing is suspended.
• F
or tire swings, extend surfacing in a circle whose radius is equal to the height of the suspending chain or rope, plus 6 feet (1.8 m) in all directions.
Protective Surfacing-Reducing Risk of Serious Head Injury From Falls
From the CPSC Outdoor Home Playground Safety Handbook. At http://www.playgroundregs.com/resources/CPSC%20324.pdf
Denotes Use Zone with Protective Surfacing
Denotes Use Zone with Protective Surfacing
6 ft.
6 ft.
6 ft. (1.8m)
6 ft. (1.8m)
(1.8m)
6 ft.
(1.8m)
(1.8m)
6 ft.
(1.8m)
6 ft.
(1.8m)
Use Zone for Multi-Axis SwingsUse Zone for Single-Axis Swings

4
Instructions for Proper Maintenance
sand and repaint using a non-lead paint
splinteringof wood.
Check for sharp edges or protrudingscrew threads, add
washers if required.
fill protective surfacing materials to prevent compaction and
Check for looseness, damage ordeterioration. Should firmly
if necessary.
Check that bolts are secure and tight. Quick clips should be
completely closed and threaded clips screwed tight.
parts including swingseats, ropes, chains and attachments
Check that ropes are tight, secure at both ends and cannot
loop back as to create an entrapment.
Check all wood members fordeterioration, structural
damage and splintering. Sand down splinters and replace
deteriorated wood members. As with all wood, some
checking and small cracks in grain is normal.
basis is important maintenance to maintain maximum life
and performance oftheproduct.
Check the following at the beginning of the play season:
This will causesplinteringof wood.
Check for sharp edges orprotrudingscrew threads.
Add washers ifrequired.
materials to prevent compaction and maintain appropriate
Check twice a month during play season:
Check that they are secure and orientated correctly. Hook
should rotate freely and perpendicular to support beam.
Check swingseats, all ropes, chains and attachments for
fraying, wear, excessive corrosion ordamage.
Check once a month during play season:
To prolongtheir life, remove swings and store insidewhen
plasticparts may become morebrittle.
materials to prevent compaction and maintain appropriate
Check at the end of the play season:
If you disposeof your play set:
hazards at thetime it is discarded. Besure to follow yourlocal wasteordinances.
beyond T-Nut
flat washer
Your KidKraft Play System is designed and constructed of quality materials with your child’s safety in mind. As with
all outdoor products used by children, it will weather and wear. To maximize the enjoyment, safety and life of your
Play Set, it is important that you, the owner, properly maintain it.

5
About Our Wood
KidKraft Premium Play Systems uses only premium playset lumber, ensuring the safest product for your
children’s use. Although we take great care in selecting the best quality lumber available, wood is still a
product of nature and susceptible to weathering which can change the appearance of your set.
What causes weathering? Does it affect the strength of my Play System?
One of the main reasons for weathering is the effects of water (moisture); the moisture content of the wood
at the surface is different than the interior of the wood. As the climate changes, moisture moves in or out
of the wood, causing tension which can result in checking and or warping. You can expect the following
due to weathering. These changes will not affect the strength of the product:
1. Checking is surface cracks in the wood along the grain. A post 4” x 4” (101mm x 101mm) will experience
more checking than a board 1” x 4” (25mm x 101mm) because the surface and interior moisture content
will vary more widely than in
thinner wood.
2. Warping results from any distortion (twisting, cupping) from the original plane of the board and often
happens from rapid wetting and drying of the wood.
3. Fading happens as a natural change in the wood color as it is exposed to sun-light and will turn a grey
over time.
How can I reduce the amount of weathering to my Play System?
At the factory we have coated the wood with a water repellent or stain. This coating decreases the amount
of water absorption during rain or snow thus decreasing the tension in the wood. Sunlight will break down
the coating, so we recommend applying a water repellent or stain on a yearly basis (see your local stain
and paint supplier for a recommended product).
Most weathering is just the normal result of nature and will not affect safe play and enjoyment for your
child. However if you are concerned that a part has experienced a severe weathering problem please call
our consumer relations department for further assistance.
Complete and mail registration card to receive important product notifications and assure prompt
warranty service.

6
KidKraft Limited Warranty
MISSING OR DAMAGED PARTS:
KidKraft will replace any parts within 90 days from date of purchase found to be missing from or
damaged in the original packaging. See Fig.1
Fig. 1 Product Age (All Parts) Consumer Pays
0-90 Days from date of purchase $0 for Part + Free Shipping
DEFECTS IN MATERIAL AND WORKMANSHIP:
KidKraft warrants that this product is free from defects in materials and workmanship for a period of one
(1) year from the original date of purchase (dated sales receipt and/or product registration is required).
This one (1) year warranty covers all parts including wood, hardware, and all accessories (Such as
swings, rides, and slides). See Fig. 2
Fig. 2 Product Age (All Parts) Consumer Pays
91 Days to 1 Year $0 for Part + Free Shipping
WOOD ROT, DECAY, AND INSECT DAMAGE:
All wood carries a five (5) year warranty against rot, decay, and insect damage (dated sales receipt
and/or product registration is required). Refer tothe schedule below for charges associated with
replacement of wood parts under this Limited Warranty. See Fig. 3
Fig. 3 Product Age (Wood Parts) Consumer Pays
0 Days to 1 Year $0 for Part + Free Shipping
After 1 Year to 5 Year $0 for Part + Shipping & Handling
Over 5 Years 100% for Part (if available) + Shipping & Handling
This warranty applies to the original owner and registrant and is non-transferable. Regular maintenance
is required to ensure the integrity of this product. Failure by the owner to maintain the product according
to the maintenance requirements may void this warranty.
This Limited Warranty does NOT cover:
• Any inspection cost
• Labor and/or costs for replacement of any defective item(s), including but not limited to,
professional installer costs
• Incidental or consequential damages, including but not limited to, as a result of set relocation,
move and/or reinstall
• Cosmetic defects which do not affect performance or integrity of a part or the entire product
• Vandalism, improper use or installation, or acts of nature, including but not limited to, high winds,
fire, and flood
• Minor twisting, warping, checking, or any natural occurring properties of wood that do not affect
performance or integrity.
• Any KidKraft product purchased, including but not limited to, a non-approved retailer, auction
houses, second-hand, and as-is clearance items.
KidKraft products have been designed for safety and quality. Modifications made to the original product
may damage the structural integrity of the unit leading to failure and possible injury. KidKraft cannot
assume any responsibility for the modified products. Furthermore, modifications void all warranties.
This product is warranted for RESIDENTIAL USE ONLY. Under no circumstance should a KidKraft
product be used in public settings such as schools, churches, playgrounds, parks, home and
professional day cares and the like. Such use may lead to product failure and potential injury. Public use
will void this warranty. KidKraft disclaims all other representations and warranties of any kind, express or
implied.

7
This identifies information that requires special
attention. Improper assembly could lead to an unsafe
or dangerous condition.
Where this is shown, 2 or 3 people
are required to safely complete the
step. To avoid injury or damage
to the assembly make sure to get
help!
Check that assembly is square
before tightening bolts.
Use a measuring tape to assure
proper location.
Check that set or assembly is properly level
before proceeding.
Pre-drill a pilot hole
before fastening screw
or lag to prevent
splitting of wood.
This indicates time to tighten bolts, but
not too tight! Do not crush the wood.
This may create splinters and cause
structural damage.
Part Identification Key
On each page, you will find the parts
and quantities required to complete the
assembly step illustrated on that page.
Here is a sample.
Key Number: The first two digits
represent the step number. The third
digit represents the piece. Note that if
the part is used in multiple steps then
the number only reflects the first step it
is used in.
Symbols
Throughout these instructions symbols are provided as important reminders for proper and safe assembly.
Proper Hardware Assembly
Lag screws require drilling pilot
holes to avoid splitting wood. Only
a flat washer is required. For ease of
installation liquid soap can be used
on all lag-type screws.
For bolts, tap T-Nut into hole with
hammer. Insert the hex bolt through
lock washer first then flat washer then
hole. Because the assemblies need to
be squared do not completely tighten
until instructed. Pay close attention to
diameter of the bolts. 5/16” (8mm) is slightly
larger than 1/4” (6.4mm).
Note: Wafer head bolts with blue lock
tight or a bolt with a Ny-Lok nut do
NOT require a lock washer.
Once the assembly is tightened, watch for exposed threads.
If a thread protrudes from the T-Nut, remove
the bolt and add washers to eliminatethis condition.
Extra washers have been provided for this purpose.
Use
Help
Use
Help
Measure
Distance
Square
Assembly
Use
Level
Pre-drill 1/8”(3mm) & 3/16”(5mm) Bit
Tighten
Bolts
CAUTION – Protrusion Hazard
Keys to Assembly Success
Tools Required
Quantity Key Number Part Description,
Part Size
2X 1012 P
No Yes
Lag Assembly
Bolt Assembly
Flat Washer
Lag Screw
Hex Bolt
Lock
Washer
Flat
Washer
Before mounting Lag
Screw, use factory drilled
holes as guides to drill 1/8”
(3.2mm) pilot holes
T-Nut
(Hammer into place)
Do not crush wood!
If Bolt protrudes
beyond T-Nut
Use an extra
flat washer
• Tape Measure
• Carpenters Level
• Carpenters Square
• Claw Hammer
• Standard or Cordless Drill
• Rubber Mallet
• #1 Phillips, #2 Robertson
and Screwdriver
• Ratchet with extension
1/2” (13mm) & 9/16”(14 mm)
sockets
• Open End Wrench
1/2” (13mm) & 9/16”(14 mm)
• Adjustable Wrench
• 1/8”(3mm) & 3/16”(5mm)
Drill Bits
• 3/16”(5mm) Hex Key
• 8’ (2.4m) Step Ladder
• Safety Glasses
• Adult Helpers
• Pencil
3mm 5mm
ost 2 x 4 x 83” (5 cm x 10 cm x 210 cm)

8
1 inch = 25.4mm
KIDKRAFT DESIGN HARDWARE
For example:
BOLT LENGTH 4½ (4.5) inches long
114mm long
1 inch = 25.4mm
25.4mm
4.5 inches x
DIAMETER CONVERSION
LENGTH CONVERSION
=
BOLT DIAMETER 5/16 (0.31) inches 0.31 inches x 25.4mm = 8mm
For example:
HARDWARE LENGTH CHART
inches vs millimetres
6 152
5½ 140
5 127
4½ 114
4 102
3½ 89
3 76
2½ 64
2 51
1½ 38 1¼ 32
1-1/8 29
1 25.4
7/8 22 3/4 19 1/2 12.7
1/4" (6mm) Flat Washer
1/4" (6mm) Lock Washer
1/4"(0.25) = 6mm Hex Bolt
1/4" (6mm) T-Nut
5/16"(.31) = 8mm Lag Screw
5/16" (8mm) Flat Washer
1/4"(0.25) = 6mm Lag Screw
1/4" (6mm) Flat Washer
5/16" (8mm) Flat Washer
5/16" (8mm) Lock Washer
5/16"(.31) = 8mm Hex Bolt
5/16" (8mm) T-Nut
3/8"(.38) = 9.5mm Lag Screw
3/8" (9.5mm) Flat Washer

9
1 x 2 1 x 4 1 x 5
1 x 6
1 x 3
1/2 x 4
5/4 x 6
5 1/2"
139.7
1"
25.4
11.1
.44
82.6
3 1/4"
4 x 4
3 1/2"
88.9
3 1/2"
88.9
4 1/2"
114.3
5/8"
15.9
15.9
5/8" 1 3/8"
34.9
2 x 6
5 3/8"
136.5
1 1/2"
38.1
15.9
5/8" 3 3/8"
85.7
60.3
2 3/8"
15.9
5/8"
1505mm
KIDKRAFT DESIGN WOOD PROFILES
LENGTH CONVERSION
For example:
1 inch = 25.4mm
BOARD LENGTH 59¼ (59.25) inches 59.25 inches x 25.4mm =
Dimensions in brackets [mm] represent millimetres.
5/4 x 4
3 1/2"
88.9
1"
25.4
5 3/8"
136.5
5/8"
15.9
2 x 4
3 3/8"
85.7
1 3/8"
34.9
5/4 x 5
4 1/2"
114.3
1"
25.4 2 x 3
2 1/2"
63.5
1 3/8"
34.9
5/4 x 3
63.5
2 1/2"
25.4
1"
2 x 2
1 1/2"
38.1
1 1/2"
38.1

10
2pc. - 1866 Window Upright (1 x 2-1/2 x 31-1/2") - Box 2 - 3641866
1pc. - 1855 Divider (1 x 4 x 34-11/16") - Box 2 - 3641855
2pc. - 1859 Wall Trim (1 x 2 x 10") - Box 3 - 3641859
1pc. - 5265 Cedar Wall (1 x 4 x 28") - Box 2 - 3635265
1pc. - 858 Dowel - Tennon (1-1/8 x 18-5/8") - Box 1 - 3681858
26pc. - 0517 Cedar Roofing (3/8 x 3-1/2 x 48") - Box 3 - 3630517
15pc. - 1852 CE Siding (3/8 x 3-1/2 x 36") - Box 3 - 3631852
3pc. - 578 Dowel - Tennon (1-1/8 x 15-7/8") - Box 1 - 3681578
3pc. - 1870 Trim Short (1 x 2-1/2 x 19-5/8") - Box 2 - 3641870
Part Identification (Reduced Part Size)
Nominal Size
1" x 2"
1" x 2½"
1" x 4"
Actual Size
⅝" x 1⅜"
⅝" x 1¾"
⅝" x 3⅜"
Part Identification (Reduced Part Size)Part Identification (Reduced Part Size)
4pc. - 1846 CE Wall (1 x 4 x 34") - Box 2 - 3631846
1pc. - 1808 Short Trim (1 x 2 x 19-5/8") - Box 3 - 3641808
1pc. - 1809 Door Trim (1 x 2 x 36-1/2") - Box 2 - 3641809
2pc. - 0528 Side Chalk Wall (1 x 4 x 25 1/4") - Box 2 - 3630528
1pc. - 0839 CE Gap Board (1 x 4 x 38-3/4") - Box 2 - 3630839
1pc. - 1876 Window Cross (1 x 2-1/2 x 28") - Box 2 - 3641876
4pc. - 1858 Short Wall Support (1 x 4 x 24-1/4") - Box 3 - 3641858
11pc. - 1847 Siding (3/8 x 3-1/2 x 24-7/8") - Box 3 - 3631847
5pc. - 1848 CE Siding (3/8 x 3-1/2 x 9") - Box 3 - 3631848
5pc. - 1850 Siding (3/8 x 3-1/2 x 26-3/4") - Box 3 - 3631850
7pc. - 1849 Cedar Siding (3/8 x 3-1/2 x 46-5/8") - Box 3 - 3631849
5pc. - 1814 Wall Support (1 x 4 x 45-1/2") - Box 3 - 3641814

11
2pc. - 0351 Front Back (1 x 5 x 46-5/8") - Box 2 - 3640351
2pc. - 1501 Floor End (1 x 5 x 38-1/4") - Box 2 - 3641501
1pc. - 1505 Front Top (1 x 5 x 46-1/2") - Box 3 - 3641505
1pc. - 1865 SW Roof Side (1 x 4 x 59-1/2") - Box 3 -
3641865
1pc. - 1869 Door Top (1 x 4 x 46-5/8") - Box 2 - 3641869
1pc. - 1864 SL Roof Side (1 x 4 x 59-1/2") - Box 3 -
3641864
Part Identification (Reduced Part Size)
Nominal Size
1" x 4"
1" x 5"
1" x 6"
Actual Size
⅝" x 3⅜"
⅝" x 4½"
⅝" x 5⅜"
Part Identification (Reduced Part Size)Part Identification (Reduced Part Size)
2pc. - 0357 Tarp Front Back (1 x 4 x 47-3/4") - Box 2 - 3640357
1pc. - 1857 Top Back (1 x 4 x 46 1/2") - Box 2 - 3641857
4pc. - 0606 CE Access Board (1 x 6 x 19-3/4") - Box 2 - 3630606
1pc. - 0353 MK Ground (1 x 4 x 55-1/4") - Box 2 - 3640353
4pc. - 0514 Roof Brace (1 x 6 x 13") - Box 3 - 3640514
1pc. - 1872 Ground (1 x 5 x 75-5/8") - Box 2 - 3641872
2pc. - 1853 Cedar Gap Board (1 x 5 x 38-3/4") - Box 2 - 3631853
1pc. - 1854 Centre Gap Board (1 x 5 x 38-3/4") - Box 2 - 3631854
1pc. - 1874 Side Ground (1 x 5 x 38-1/4") - Box 3 - 3641874
8pc. - 1851 Cedar Floor Board (1 x 5 x 38-3/4") - Box 2 - 3631851

12
1pc. - 1867 Top Side (1 x 6 x 38-1/4") - Box 2 - 3641867
1pc. - 1868 Table Support (2 x 2 x 38-3/4") - Box 2 - 3641868
1pc. - 0376 Table Top (5/4 x 6 x 32") - Box 3 - 3640376
2pc. - 0367 Floor Gusset (2 x 3 x 11") - Box 3 - 3640367
1pc. - 0799 Floor Back (5/4 x 4 x 46-3/4") - Box 2 - 3640799
1pc. - 0790 Floor Joist (5/4 x 4 x 46-1/2") - Box 2 - 3640790
2pc. - 0501 Joist (2 x 2 x 43 1/2") - Box 3 - 3640501
Part Identification (Reduced Part Size)
Nominal Size
1" x 6"
5/4" x 4"
2" x 2"
2" x 3"
Actual Size
⅝" x 5⅜"
1" x 3¼"
1½" x 1½"
1⅜" x 2½"
Part Identification (Reduced Part Size)Part Identification (Reduced Part Size)
4pc. - 0369 Lower Diagonal (2 x 3 x 37") - Box 2 - 3640369
1pc. - 0522 Window Dormer Cleat (5/4 x 2 x 8") - Box 3 - 3630522
1pc. - 1862 SW Support (5/4 x 4 x 46-1/2") - Box 2 - 3641862
1pc. - 1875 Short Joist (2 x 2 x 16-1/2") - Box 3 - 3641875
1pc. - 1860 MK Mount (2 x 3 x 34-13/16") - Box 2 - 3641860
1pc. - 1871 Long Joist (2 x 2 x 24-3/4") - Box 3 - 3641871
1pc. - 1873 Back Floor (5/4 x 4 x 46-3/4") - Box 2 - 3641873
3pc. - 0630 CE Rock Board (1 x 6 x 19 3/4") - Box 2 - 3630630
2pc. - 0631 CE Rock Board (1 x 6 x 19-3/4") - Box 3 - 3630631
4pc. - 0863 Roof Support (2 x 3 x 43 1/2") - Box 2 - 3640863
2pc. - 0349 Rock Rail (2 x 3 x 51") - Box 3 - 3640349
1pc. - 0795 Side Joist (2 x 2 x 43") - Box 3 - 3640795
6pc. - 0318 Ground Stake (1-1/4 x 1-1/2 x 14") - Box 1 - 3650318

13
4pc. - 1500 Post (2 x 4 x 83") - Box 2 - 3641500
1pc. - 1826 Front Beam (2 x 6 x 83-5/8") - Box 3 - 3631826
1pc. - 1856 SW Upright (2 x 4 x 48-5/16") - Box 2 - 3641856
2pc. - 1863 SW Post (2 x 4 x 86-11/16") - Box 3 - 3641863
1pc. - 1825 Back Beam (2 x 6 x 83-5/8") - Box 3 - 3631825
Part Identification (Reduced Part Size)
Nominal Size
2" x 3"
2" x 4"
2" x 6"
Actual Size
1⅜" x 2½"
1⅜" x 3⅜"
1½" x 5⅜"
Part Identification (Reduced Part Size)Part Identification (Reduced Part Size)
1pc. - 4919 SW Rail Block (2 x 4 x 5-3/8") - Box 3 - 3644919
1pc. - 1861 SW Mount (2 x 4 x 38-1/8") - Box 3 - 3641861
2pc. - 1367 Post MK (2 x 3 x 70") - Box 3 - 3641367
2pc. - 1564 MK Rail Long (2 x 4 x 52") - Box 3 - 3641564
1pc. - 0521 Window Dormer Roof Left - Box 3 - 3630521
1pc. - 0520 Window Dormer Roof Right - Box 3 - 3630520

14
1X 3200202
Glider Hanger
(2pk)
1X 3320356
Big Backyard I.D
Plaque w hardware
2X 3724943
42" Belt Swing Yellow
w.welded chain
1X 3200184
Triangle Plate (4pk)
Green
1X 3533860
39" Glider Rope & Chain
(4pk) w. welded chain
1X 3202000
Swing Hanger Bolt
Thru. (4 pk)
1X 3320273
2 person Glider Seat
Yellow
2X 3320172
2 person Glider End
1X 3750855
CBA
Ridgeview Deluxe Tarp Set
1X 3750702
Pineview Chalkwall
1X 9750856
Café Canopy
1X 9200840
Café Canopy Frame
1X 3320401
Flower Box Set
Green
1X 9200140 (2pk)
MB Mount Strap Set
1X 9200300 (2pk)
Monkey Bracket Set
1X 9201103 (4pk)
Corner Brace Set
1X 9209900
Window Dormer Bkt
1X 3320094
Door Window
Green
w/ hardware
1X 3320197
Small Window Dormer
Green
1X 3320190
Stool Seat Set
2X 3320121
Peak Detail
Green
1X 3201104
Ridgeview Deluxe Brkt Set
Part Identification (Reduced Part Size)
1X 3320386 Rocks (5pk)
3-Green 2-Yellow
1X 3310148
Slide 48" High Rail
Green
1X Glider Seat
2X Glider End
1X 9320374
KidKraft I.D Plaque w
hardware
1X 9750189
Selwood
Window Mesh

15
4pc. H5 - Hex Bolt 1/4 x 4-1/2" - (9277242)
4pc. H7 - Hex Bolt 1/4 x 5-1/2" - (9277252)
Hardware Identification (Actual Size)
1pc. H8 - Hex Bolt 1/4 x 4-1/4" - (9277241)
4pc. LS1 - Lag Screw 1/4 x 1-1/2" - (9262212)
3pc. LS2 - Lag Screw 1/4 x 2-1/2" - (9272222)
8pc. LS3 - Lag Screw 1/4 x 3" - (9262230)
1pc. H1 - Hex Bolt 1/4 x 1-1/2" - (9277212)
4pc. H3 - Hex Bolt 1/4 x 2-1/2" - (9277222)
20pc. H2 - Hex Bolt 1/4 x 2" - (9277220)
3pc. H12 - Hex Bolt 1/4 x 3" - (9277230)
1pc. H13 - Hex Bolt 1/4 x 3-1/2" - (9277232)

16
2pc. G8 - Hex Bolt 5/16 x 2" - (9277320)
3pc. G10 - Hex Bolt 5/16 x 3" - (9277330)
4pc. G4 - Hex Bolt 5/16 x 4" - (9277340)
4pc. G1 - Hex Bolt 5/16 x 1-1/2" - (9277312)
2pc. Z - Hex Bolt 5/16 x 6" - (9277360)
4pc. G2 - Hex Bolt 5/16 x 1" - (9277310)
4pc. G7 - Hex Bolt 5/16 x 5-1/2" - (9277352)
5pc. G5 - Hex Bolt 5/16 x 4-1/2" - (9277342)
Hardware Identification (Actual Size)
5/16” Glider Long Hex Bolt
Bolt may not be exactly as it appears

17
41pc. S5 - Pan Screw#8 x 1/2"- (9264504)
82pc. S1 -Wood Screw#8 x 1-1/8"- (9290514)
148pc. S2 -Wood Screw#8 x 1-1/2"- (9260512)
239pc. S0 - Truss Screw #8 x 7/8"- (9229505)
6pc. PB2 - Pan Bolt1/4 x 1-1/4"- (9274211)
20pc. LW2 - 5/16" Lock Washer - (9253300)
12pc. LN2 - 5/16" Lock Nut- (9283300)
20pc. TN2 - 5/16" T- Nut - (9285300)
5pc. BN1- 1/4" Barrel Nut- (9248200)
16pc. S8 - Pan Screw#12 x 3/4"- (9264603)
39pc. TN1 - 1/4" T - Nut -(9285200)
44pc. LW1 - 1/4" Lock Washer - (9253200)
44pc. FW2 - 5/16" Flat Washer - (9251300)
70pc. FW1 - 1/4" Flat Washer - (9251200)
19pc. FW0 - 3/16" Flat Washer - (9251100)
25pc. FW3 - #8 Flat Washer - (9251500)
Hardware Identification (Actual Size)
22pc. S3 -Wood Screw#8 x 2-1/2"- (9290522)
7pc. S4 -Wood Screw#8 x 3" - (9290530)
25pc. S7 - Pan Screw#12 x 2" - (9264620)
16pc. S6 - Pan Screw#12 x 1" - (9264610)
4pc. S15 -Wood Screw#8 x 1-3/4"- (9260513)
5pc. S10 - Pan Screw#8 x 1" - (9264510)

18
B. If there are any missing or damaged pieces or you need assistance with
assembly please contact the Consumer Relations Department directly. Call us
before going back to the store.
STOP STOPSTOP STOP
Step 1: Inventory Parts - Read This Before Starting Assembly
C. Read the assembly manual completely, paying special attention to ANSI warnings;
notes; and safety/maintenance information on pages 1 - 7.
D. Before you discard your cartons ll out the form below.
• The carton I.D. stamp is located on the end of each carton. The tracking number is
located on the KidKraft ID Plaque (9320374).
• Please retain this information for future reference. You will need this information if you
contact the Consumer Relations Department.
• Please refer to Page 7 for proper hardware assembly.
• Each step indicates which bolts and/or screws you will need for assembly, as well as
any at washers, lock washers, t-nuts or lock nuts.
A. This is the time for you to inventory all your hardware, wood and accessories,
referencing the parts identication sheets. This will assist you with your assembly.
• The wood pieces will have the four digit key number stamped on the ends of the
boards. The wood pieces are referenced throughout the instructions with this number.
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 4)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 5)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 6)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 1)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 2)
CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 3)
MODEL NUMBER: F270855
TRACKING NUMBER (from ID Plaque):
[phone]
[email protected]
For online parts replacement visit
https://parts.kidkraft.eu/
1.800.933.0771 or 972.385.0100
[email protected]
[email protected]
For online parts replacement visit
https://parts.kidkraft.com/

19
Wood Parts Hardware Other Parts
Step 2: Rock Wall Assembly
A: Lay 2 (0349) Rock Rails down, side by side with angled edges facing down. (g. 2.1)
B: Place (0606) CE Access Board on the bottom of each (0349) Rock Rail as shown in g. 2.1. Make sure (0606)
CE Access Board is ush to the outside and bottom edges of each (0349). Attach using 4 (S2) #8 x 1-1/2” Wood
Screws.
C: 7-3/4” down from the top of both (0349) Rock Rails place 1 (0630) CE Rock Board, making sure the sides are
ush to the outside edges of each (0349) Rock Rail. Attach using 4 (S2) #8 x 1-1/2” Wood Screws. (g. 2.1)
D: In between the (0606) CE Access Board and (0630) CE Rock Board stagger 2 (0630) and 2 (0631) CE Rock
Boards using 4 (S2) #8 x 1-1/2” Wood Screws per board. Placing them as shown in g. 2.1, this will prevent rocks
from forming a straight line. Make sure the boards are evenly spaced and do not exceed 2-3/8” between boards.
E: Place 1 rock on each (0630) and (0631)
CE Rock Board (g. 2.2) and attach using 1
(PB2) 1/4 x 1-1/4” Pan Bolt (with lock washer,
at washer and barrel nut) and 1 (S10) #8 x
1” Pan Screw per rock. The Screw must be in
the hole directly under the Pan Bolt, it will stop
the rock from spinning. (g. 2.3)
Note: Gaps between boards 2-1/4”,
not to exceed 2-3/8”
Note: The holes
in the rock boards
must orient to the
top of the boards.
7-3/4”
Approx
Fig. 2.1
S2 0606 0349
0631
0630 0630 0630
0631
Fig. 2.2
Fig. 2.3
1 x CE Access Board 1 x 6 x 19-3/4”
3 x CE Rock Board 1 x 6 x 19-3/4”
2 x CE Rock Board 1 x 6 x 19-3/4”
2 x Rock Rail 2 x 3 x 51”
24 x #8 x 1-1/2” Wood Screw
5 x #8 x 1” Pan Screw
5 x 1/4 x 1-1/4 Pan Bolt
(1/4” lock washer, 3/16” at washer & 1/4” barrel nut)
S2
0349
0631
0630
0606
3/16” Flat
Washer
1/4” Lock
Washer
1/4” Barrel
Nut
Rock
5 x Rocks (3 green/2 yellow)
S10
S10
PB2
PB2

20
Step 3: Swing Beam Assembly
Make sure triangle is
tight against beam
Warning: For your child’s safety,
orientate the swing hangers as
shown to ensure your swing will
have proper swing motion when
installed. Failure to do so could
result in premature failure of the
swing hanger or swing chain.
A: In the middle holes of (1825)
Back Beam install 2 Bolt-Thru Swing
Hangers (g. 3.1) making sure the
swing hangers are oriented in the
direction shown in g. 3.4 to maintain
proper swing motion.
B: In the end holes of (1826) Front Beam install 2
Bolt-Thru Swing Hangers (g. 3.1) making sure the
swing hangers are oriented in the direction shown in
g. 3.4 to maintain proper swing motion.
4 x 1/4 x 5-1/2” Hex Bolt
(1/4” at washer, 1/4” lock washer, 1/4” t-nut)
4 x 5/16 x 1-1/2” Hex Bolt
(5/16” at washer, 5/16” lock washer, 5/16” t-nut)
H7
G1
1 x Bolt-Thru Swing Hangers (pkg of 4)
1 x Triangle Plate (pkg of 4)
1 x Front Beam 2 x 6 x 83-5/8”
1 x Back Beam 2 x 6 x 83-5/8”
1826
1825
Fig. 3.4
Bolt-Thru Swing Hangers
Wood Parts Hardware Other Parts
Fig. 3.1
C: Attach 1 Triangle Plate to the
ends of each (1826) Front Beam
and (1825) Back Beam using 1
(G1) 5/16 x 1-1/2” Hex Bolt (with
lock washer, at washer and
t-nut) per triangle plate in the hole
indicated in g. 3.2 & 3.3. Correct
hole usage is very important.
Triangle
Plates
Important!
Swing End
(With Overhang)
G1
H7
H7
1826
Important!
Fort End Side
(No Overhang)
Fig. 3.2
Fig. 3.3
D: Attach 1 (H7) 1/4 x 5-1/2” Hex
Bolt (with lock washer, at washer
and t-nut) to the ends of each (1826)
Front Beam and (1825) Back Beam.
The bolts do not attach to anything,
but MUST be installed to the beams
to prevent splitting and checking of
wood. (g. 3.2 & 3.3)
Swing End
(With Overhang) Fort End Side
(No Overhang)
1825
G1
H7
G1
H7
G1
1/4” Flat
Washer
1/4” Lock
Washer
1/4” T-Nut
5/16” Flat
Washer
5/16” Lock
Washer
5/16” T-Nut
1826
1825
Bolt-Thru Swing Hangers
Make sure holes are aligned.