Kikusui KRC Series User manual

The KRC series Cabinet rack comply with JIS standard or EIA standard.
Support angles are included.
•The maximum allowable load of each pair of support angles is 70 kg.
For heavier loads, use support angles for heavy weight (optional
items).
•When assigning devices to be accommodated in the rack, fix the rack
with the levelers to prevent the it from moving, and then assign
devices so that the gravity center of overall rack is made as low as
possible.
•The rack may fall by the earthquake. Take measures to prevent the fall.
•When moving the rack, raise the levelers up to the highest position.
The rack may fall at a difference in level.
•To hoist the rack, raise it by means of the eyebolts (optional items).
Specifications
Options
Using Optional Items
■OP01-KRC/OP02-KRC
Turn the surface marked a circle of the plate nut to you. Insert the nut into the
pillar and turn it 90 degree clockwise. Check that the nut does not fall down from
the pillar and fix the support angle with the screw.
I0022501
Jun 2020
Instruction Manual
Cabinet Rack KRC Series
Model H H1 D D1 Model H H1 D D1
KRC363L 1835 1600 950 800 KRC1603L 1835 1600 950 800
KRC273L 1435 1200 950 800 KRC1203L 1435 1200 950 800
KRC363 1835 1600 800 650 KRC1603 1835 1600 800 650
KRC273 1435 1200 800 650 KRC1203 1435 1200 800 650
CAUTION
H
452
H1
D1
570 D
Base
Leveler
Unit: mm
Model
Allowable
max. load No. of panels Weight Support
angle Leveler
kg JIS EIA kg
KRC363L
Approx. 300
36 95 12 (6 in pairs)
4
KRC273L 27 85 10 (5 in pairs)
KRC363 36 90 12 (6 in pairs)
KRC273 27 75 10 (5 in pairs)
KRC1603 32 90 12 (6 in pairs)
KRC1603L 95
KRC1203 24 75 10 (5 in pairs)
KRC1203L 85
Model Description Remarks
OP01-KRC Support angle For add-in (the same as provided support angle)
OP02-KRC Support angle for heavy weight Use this to load to a pair of support angle over 70 kg.
OP03-KRC Base hold angle Use this to fix the rack to the floor.
OP04-KRC Eyebolt Use this to hoist the rack.
No. Description Quantity
OP01-KRC OP02-KRC
1 Support rail 2 2
2 Plate nut 4 8
3 Screw M5x16 (Double sems) 4 8
OP01-KRC OP02-KRC
2
1
3
2
1
3

KIKUSUI ELECTRONICS CORP.
1-1-3 Higashiyamata, Tsuzuki-ku, Yokohama,
224-0023, Japan
www.kikusui.co.jp/en
■OP03-KRC
Put the base hold angles to the both sides (right and left sides or front and rear
sides) of the base of rack.
The base hold angle has a long hole for M16 on the bottom side. Fix the rack with
anchor bolts.
■OP04-KRC
Remove the hole caps on the top side, put the eyebolts to the rack.
No. Description Quantity
1 L-shape anchor 4
2 Bolt M10x35 8
3 Spring washer M10 8
4 Washer M10 8
5 Nut M10 8
Model
Fixing the right
and left sides
Fixing the front
and rear sides
W1 D1 W2 D2
KRC363L
670
450
270
1050
KRC273L 450 1050
KRC363 380 900
KRC273 380 900
KRC1603L 450 1050
KRC1203L 450 1050
KRC1603 380 900
KRC1203 380 900
Unit: mm
W1
D1
W2
D2
Location of anchor bolt holes
Base of
the rack
Base of
the rack
2
3
4
1
5
Hole for M16
Secure the rack with anchor bolts.
No. Description Quantity
1 Eyebolt M12x22 4
2 Washer M12 4
1
2