Kinder Sydney Cot User manual

Dimensions(cm): (L)125 x (W)65.5 x (H)91*
Fits Mattress Size(cm): (L)120 x (W)60
• Easy assembly • Safe & Sturdy • Solid Pine Wood
• 3 Base Height Positions • Teething Rails
*Approx. measurements only. Sizes may vary.
Contact Us...
E[email protected]
T0844 7744644 - Option 2
www.kinder-valley.com
Vaey
K I N D E R®
ASSEMBLY INSTRUCTIONS
Sydney Cot
*FACTORY CODE*
IMPORTANT, RETAIN FOR FUTURE
REFERENCE: READ CAREFULLY

ASSEMBLY INSTRUCTIONS
SYDNEY COT
Vaey
K I N D E R®
IMPORTANT, RETAIN FOR FUTURE REFERENCE:
READ CAREFULLY
Instructions for safe use:
Before you start
WARNING - Be aware of the risk of open fire and other sources of strong heat, such as
electric bar fires, gas fires, etc. in the near vicinity of the cot.
WARNING - Do not use this child’s cot if any part is broken, torn or missing and use
only spare parts approved by Kinder Valley.
WARNING - Do not leave anything in the cot or place the cot close to another product,
which could provide a foothold or present a danger of suffocation or strangulation,
eg. strings, blind/curtain cords etc.
WARNING - Do not leave anything in the cot or place the cot close to another product,
which coul provide a foothold or present a danger of suffocation or strangulation, e.g
strings, blind/curtain cords.
WARNING - Do not use more than one mattress in the cot.
This Kinder Valley cot conforms to BS EN 716-1:2017.
This Kinder Valley cot is suitable from birth to approximately 3 years.
To be prevent injury, the cot should not be used as soon as the child is able to climb out
of the cot unaided.
The lowest mattress base position is the safest, the base should always be used in that
position as soon as the baby is old enough to sit up.
This cot is intended to be used by one child at a time.
Thickness of the mattress shall be such that the internal height (surface of the mattress to
the upper edge of the cot frame) is at least 500mm in the lowest position of the cot base
and at least 200mm in the highest position of the cot base.
We recommend you use any Kinder Valley mattress size 120cm x 60cm x 10cm. The
length and width shall be such that the gap between the mattress and sides and ends
does not exceed 30mm.
Use only on firm ground which is on a horizontal level and dry.
All assembly fittings should be tightened properly and fittings should be checked regularly
and retightened as necessary.
This cot is designed to be dismantled and packed flat for storage or transportation.
In order to clean, use only a mild detergent and warm water. Do not bleach
or use any abrasive substances.

CHECK THAT YOU HAVE ALL FIXTURES AND FITTINGS BEFORE
ASSEMBLY, AND ENSURE THEY ARE NOT BROKEN.
A x2 Cot Ends
Number of people to assemble:
Two adults are required to
assemble this item.
x1 Base
x2 Side Rails
B
C
Fixtures & Fittings
x12 Bolts x12 Barrel Nuts DE
x1 Allen Key
F

IMPORTANT - RETAIN FOR FUTURE REFERENCE
Step 1
Join Cot End to Side Rail with x2 Bolts and x2 Barrel Nuts .
A B D E
D
D
A
B
E
E
Step 2
D
E
E
D
A
Join remaining Cot End to with x2 Bolts and x2 Barrel Nuts .
A D E
Step 1

IMPORTANT - RETAIN FOR FUTURE REFERENCE
D
E
Step 3
E
D
E
Join Cot Base to at the required base height position with x4 Bolts and
x4 Barrel Nuts .
C D
E
Step 2
CE
D
D
Step 4
Complete assembly of your Cot by joining the remaining Side Rail with
x4 Bolts and x4 Barrel Nuts .
B
D E
D
E
D
E
B
E
D
E
D