kinetic M-DAB 0001 Operation manual

digitizor
digitizordigitizor
digitizor
TM
listen to something new
M-DAB 0001
Automotive DAB / DAB+ / DMB-A tuner
Installation & User Guide

Kinetic
®
digitizor
TM
M-DAB 0001 User Guide
1
ONTENTS page
!! SAFETY FIRST !! 2
INTRODU TION 3
WHAT IS IN LUDED 4
THE REMOTE ONTROL 5
INSTALLATION 8
WIRED ONNE TION - SET-UP 9
WIRED ONNE TION - USE 11
WIRELESS ONNE TION SET-UP #1 12
WIRELESS ONNE TION SET-UP #2 14
USE IN AF (AUTOMATI FREQUEN Y HANGE) MODE 16
USE IN AUTOS AN MODE 18
SELE TING DAB STATIONS 20
AUXILIARY INPUT 21
digitizor MESSAGES ON YOUR FM-RDS RADIO DISPLAY 22
TROUBLESHOOTING 23
HANGING digitizor's ONNE TION METHOD 24
ESSENTIAL INFORMATION ABOUT DAB AR AERIALS 25
SPE IFI ATION 26
WARRANTY 26
WASTE DISPOSAL 26

Kinetic
®
digitizor
TM
M-DAB 0001 User Guide
2
!! SAFETY FIRST !!
FAILURE TO HEED THESE INSTRU TIONS AND WARNINGS AN
RESULT IN SERIOUS INJURY OR DEATH.
The Kinetic digitizor M-DAB 0001 receiver is designed for reception of Band III Digital
Audio Broadcasts (DAB, DAB+ and DMB-A) in conjunction with 12 volt negative ground
FM-RDS car tuners. It is unsuitable for any other purpose. Use for other than the
designed application may result in damage or injury.
Installation of digitizor is simple if you follow the step-by-step instructions but if you
are in doubt about any aspect of the installation please consult your retailer or arrange
professional installation. Warranty does not cover damage caused by incorrect
installation or use.
Do not install digitizor in a manner that would interfere with the driver’s vision, with the
safe operation of the vehicle controls or with the vehicle safety functions e.g. braking
system, seatbelts and airbags.
Do not install the equipment where it would be exposed to moisture excessive humidity,
extreme heat or where there is no ventilation, e.g. under carpet. Do not block vents or
radiator panels; doing so may cause heat build up and result in fire.
Switch off all power before connecting or disconnecting any cables.
Obey hand / power tool and other safety instructions to the letter. Before drilling any
holes, check and double check to avoid damage to hidden vehicle components (cables,
air bags, battery, etc.). Ensure cable holes are grommeted.
Ensure that the installation is secure, with no loose parts.
Use the correct ampere rating when replacing fuses. Failure to do so may result in fire,
electric shock or damage that is not covered by warranty.
There is a risk of explosion or equipment damage if the remote control's battery is
replaced incorrectly.
Do not disassemble or alter the equipment. Doing so will void the warranty and may
result in fire or electric shock.
Keep small objects such as batteries out of the reach of children and pets. Swallowing
them may result in serious injury. If swallowed, consult a physician immediately.
When driving, do not operate any function that could distract you from safe control of
your vehicle. Any function that requires your attention should only be performed
before you commence your journey or after coming to a complete stop in a safe
location.

Kinetic
®
digitizor
TM
M-DAB 0001 User Guide
3
INTRODU TION
If you follow the step-by-step instructions, installation and use of digitizor is simple.
To skip the blurb please go directly to page 4.
DIGITIZOR'S SUPERIOR FEATURES AND BENEFITS
The Kinetic® digitizorTM M-DAB 0001 is an advanced in-car audio device that enables
you to receive DAB radio in almost any vehicle whilst retaining the vehicle's factory
appearance.
digitizor DAB is operated using a radio remote commander. All messages relating to
the system’s operations, e.g. station name, are displayed on the display of your FM-
RDS in-car audio system.
digitizor's sophisticated design incorporates a World leading high-sensitivity DAB chip
and unique, patented AF (Automatic Frequency hange) circuitry that overcomes
the need to switch FM frequency manually when there is a conflict with an FM radio
station. This feature is particularly useful in areas where there are many FM stations.
Unlike many DAB tuners, digitizor has a Pan-European specification and is capable of
receiving all DAB, DAB+ and DMB-A transmissions in Band III (except in S. Korea).
There is no need to switch between DAB, DAB+ and DMB-A; digitizor receives all
such stations automatically.
DAB, DAB+ and DMB-A
Originally there was only one 'DAB' but, somewhat confusingly, ' DAB' has come to
mean original DAB, DAB+ and DMB-A (sometimes called DMB-R). The original DAB
is widely used but some countries use or plan to use DAB+ or DMB-A. For more
information please visit www.www.worlddab.org or http://www.wohnort.org/DAB

Kinetic
®
digitizor
TM
M-DAB 0001 User Guide
4
WHAT IS IN LUDED
digitizor & DIN cables
Remote ommander R2025 Battery
Power able with igar Lighter plug Power able with bare ends
Velcro Tapes x2 Screws x2 onnectors x 8
Manual

Kinetic
®
digitizor
TM
M-DAB 0001 User Guide
5
THE REMOTE ONTROL
INSTALLING THE REMOTE ONTROL BATTERY
Hold the remote control with the back facing you and with the battery compartment to
your left. Release the small catch and simultaneously slide the battery holder out.
Fit the R2025 3 volt lithium battery (!! ensure the '+' signs on the battery, the battery
holder and the remote control match !!) to the battery holder and slide both battery and
holder into the remote control's battery slot. Ensure that the catch locks into place.
onfirm that the battery is installed and working correctly: hold any button and check
that the red LED on the top edge of the remote control illuminates.
THE REMOTE ONTROL
There is no need to point or aim digitizor's remote control towards a sensor and the
remote will work in bright sunlight, because the remote signals are sent by radio, not by
infra-red.
THE REMOTE ONTROL FUN TIONS
All you need to know to get going is explained in the set-up instructions so if you wish
you can skip the following detailed explanations of the remote's button functions for now
and go straight to page 8.

Kinetic
®
digitizor
TM
M-DAB 0001 User Guide
6
Button Press...
Any
Button
and hold to illuminate the LED on the top edge of the remote to confirm
that the battery is installed and working.
q
to toggle digitizor between ON and STANDBY.
■
1) to toggle the display between DAB station name and signal quality.
2) to confirm a command.
DAS
(DAB /
Auxiliary
Input
Selector)
1) to scroll through the three DAB preset blocs and Auxiliary Input.
2) and hold to scan for DAB stations.
▲ ▼
&
1) to scroll through the DAB station list.
2) to navigate the menus (in conjunction with the MENU button).
3) to adjust the wireless connection AutoScan mode transmission
frequency by 100 kHz (in conjunction with the FM button).
◄◄ & ►►
1) to quick scroll through the DAB station list by initial letter.
2) to navigate the menus (in conjunction with the MENU button).
3) to adjust the wireless connection AutoScan mode transmission
frequency by 2 MHz (in conjunction with the FM button).
9
1) to return to the previous DAB station.
2) and hold to reset digitizor's wireless connection AutoScan mode
transmission frequency to that saved in FM preset 1 . The default
frequency is 87.6MHz.
FM
WIRED ONNE TION:
1) to switch to FM radio.
WIRELESS ONNE TION:
1) to display digitizor’s current FM transmission frequency.
2) and hold to demand a frequency change in AutoScan and AF mode.

Kinetic
®
digitizor
TM
M-DAB 0001 User Guide
7
3) repeatedly to scroll through digitizor's Autoscanned clear FM
frequencies.
4) to access FM preset buttons (1 ~ 4) in AutoScan mode.
1 ~ 4
1) to save or recall 12 (4 x 3 blocs) preset DAB stations.
2) to save or recall 4 preset FM transmission frequencies (wireless
connection - AutoScan mode).
MENU
To enter SETTINGS MENU.
Use ◄◄ & ►► and ▲ ▼ & to navigate the settings menu.
Use
■
to confirm your selection.
[FREQUENCY] - Displays the current FM transmission frequency. Press
■
to reset the FM transmitter to 87.6MHz. (Wireless connection.)
[FM MODE] – selects operating mode (AF _H/AF _L/ AutoScan).
(Wireless connection.)
[FULLS AN] – scans for DAB/DAB+/DMB-A stations.
[ANTENNA] – must be set to ON for internally powered active DAB aerials
and OFF for all other aerials.
[DABRESET] – clears all DAB stations and DAB presets. digitizor will
automatically perform a scan for DAB stations after the reset is
completed.
[FA TORY]. - restores digitizor to Factory Settings. digitizor will
automatically perform a scan for DAB stations after the factory reset is
completed. Switch the car radio to FM 87.6MHz to continue to listen to
DAB. !!Factory reset will erase all previous system settings to default!!
[VERSION] – displays the current software version.
[UPGRADE] - for technician use only.
Most remote control commands are automatically applied after a delay of 3 or 10
seconds. To speed up the execution of such commands press the
■
button. For clarity
this function has been omitted from many of the step-by-step installation and operation
instructions.

Kinetic
®
digitizor
TM
M-DAB 0001 User Guide
8
INSTALLATION
!! digitizor requires an aerial designed for the reception of DAB Band III signals
(available separately). The benefits of digitizor's high-sensitivity DAB chip will be lost
if you fit an inferior DAB aerial. For more information please refer to page 25
'ESSENTIAL INFORMATION ABOUT DAB AR AERIALS' !!
DAB aerial installation and FM-RDS car radio operation / removal vary widely so when
necessary please refer to your DAB aerial's / car radio's / car's instruction manual.
To get your digitizor up and running straight away, first decide which type of installation
you require. (It is recommended that you use (B) below as a quick test before
permanent installation.)
A) WIRED ONNE TION SET-UP
hoose this set-up if you want a full stealth (hidden) installation with wired connection.
Provides the easiest use, the most dependable connection, the highest sound quality and
near zero chance of interference from FM radio stations. Please go to page 9.
B) WIRELESS ONNE TION SET-UP #1
hoose this set-up if you have a quick-fit (e.g. Kinetic MagnetwiG or STI ) DAB aerial,
want to move digitizor often from car to car and don't mind a visible cable or two.
Please go to page 12.
) WIRELESS ONNE TION SET-UP #2
hoose this set-up if you want a fully installed stealth installation with wireless
connection. (Unless you cannot use (A) above because it's difficult or impossible to
connect to your existing radio's FM/AM aerial connectors, there is little point in choosing
this option.) Please go to page 14.
digitizor ONNE TORS & SWIT HES
1. SMB Male connector for DAB aerial 2. 3.5mm stereo audio Auxiliary Input
3. FM DIN cables 4. Socket for power cable

Kinetic
®
digitizor
TM
M-DAB 0001 User Guide
9
WIRED ONNE TION - SET-UP
1. Observe the !!SAFETY FIRST!! on page 2.
2. Remove the FM-RDS radio from the dash of your vehicle. (If it has a security code
number, don't forget to check that you know the number before you disconnect the
power!)
3. hoose a suitable place behind or under the dash to fit your digitizor box.
4. Install a DAB car aerial (available separately - please see page 25) equipped with
an SMB(F) connector and route the cable to the location you have chosen for your
digitizor. Insert the DAB aerial plug into the DAB aerial socket of your digitizor.
5. Select the power cable without cigar lighter plug, i.e. the one with bare ends.
6. onnect the red power cable to the switched 12v cable to your FM-RDS radio.
7. onnect the black earth cable to the earth cable to your FM-RDS radio.
8. Set the switch on the side of the digitizor to 'Wired'.
9. Remove the cap from digitizor’s male FM DIN connector.
10. Unplug the car aerial cable from the car radio AM/FM aerial socket and plug it into
digitizor’s female DIN socket*.
11. Plug digitizor’s male DIN connector* into the car radio’s AM/FM aerial socket.
12. If you want to play an external audio device such as an MP3 player or iPod®
through your car radio, connect a 3.5mm stereo audio cable to digitizor's Auxiliary
Input socket. Route the cable to a convenient position for your external audio
device.
13. Switch on your car's FM-RDS car radio.
14. Set the TA/TP of your car's FM-RDS car radio to 'Off' and ensure that its display is
set to show station names.
15. Manually tune your car radio to FM 87.60Mhz and store this frequency on a
convenient preset button.
16. Turn the volume control to a moderate listening level. In UK you will hear mainly
hiss.
* Adaptors are available from your dealer for vehicles and radios with ISO, Fakra or
other types of FM connector

Kinetic
®
digitizor
TM
M-DAB 0001 User Guide
10
17. Insert the power cable plug into the 12V D socket of your digitizor and turn it
gently 90 degrees clockwise to lock it in place. The indicator LED on the digitizor
box will glow red and, after a few seconds, the hiss from your radio will cease.
18. digitizor will automatically search for DAB stations and create a station list. The
display will show [FFF N]. FFF denotes the channel currently being scanned, and N
indicates how many stations have been detected.
19. When the scan is complete, digitizor will play the DAB station that is listed first
alphabetically.
20. Your DAB aerial may require internal / phantom power (please refer to your DAB
aerial's instructions), in which case you MUST switch on the aerial power, otherwise
the aerial will not function properly, if at all:
a. Press the remote's 'MENU' button. Your radio’s display shows ‘87.6’.
b. Press the
▼
button repeatedly until 'ANTENNA' shows on your radio's display.
c. Press the
■
button.
d. Press the
▼
button until 'ANT ON' shows on your radio's display.
e. Press the
■
button.
f. Display shows 'DONE'. Aerial power is now 'ON'.
g. Press and hold the DAS button to re-scan for DAB stations.
21. Use the
▲ ▼
buttons to select a DAB station of your choice. Stations may take
a few seconds to tune, depending upon your FM/AM radio.
22. Secure the digitizor box and tidy the cables AWAY from the digitizor box. Avoid
coiling excess power or aerial cables.
23. heck all is working correctly, re-fit the FM-RDS radio and you are ready to enjoy
in-car DAB!
24. Please turn to page 11 for the detailed Wired onnection User Instructions.

Kinetic
®
digitizor
TM
M-DAB 0001 User Guide
11
WIRED ONNE TION - USE
digitizor will automatically switch on and commence transmitting on FM 87.6MHz each
time you turn on the car ignition.
1. Turn on your in-car audio system and go to the FM band.
2. Ensure your car radio's display is set to show FM station names.
3. If your car radio has TP and/or TA functions please set them to 'off'.
4. Tune the car radio’s FM frequency to FM 87.6 MHz and memorize this frequency on a
convenient preset button.
5. Select DAB stations according to the instructions on page 20.
Press the FM button when you want to listen to FM/AM stations.
To return to DAB, press the DAS button and retune your car radio to 87.6 MHz.

Kinetic
®
digitizor
TM
M-DAB 0001 User Guide
12
WIRELESS ONNE TION SET-UP #1
1. hoose a suitable location for your digitizor. For the best wireless performance,
position digitizor close to the car radio, with no intervening metal objects.
2. Install a DAB car aerial (available separately) equipped with an SMB(F) connector
and route the cable to the location you have chosen for your digitizor. Insert the
aerial plug into the DAB aerial socket of your digitizor.
3. Set the switch on the side of the digitizor to 'Wireless'.
4. Leave the two FM/AM aerial leads unconnected with the cap in place on the male
DIN connector.
5. If you want to play an external audio device such as an MP3 player or iPod®
through your car radio, connect a 3.5mm stereo audio cable to digitizor's Auxiliary
Input socket. Route the cable to a convenient position for your external audio
device.
6. Insert the power cable plug into the 12V D socket of your digitizor and turn it
gently 90 degrees clockwise to lock it in place.
7. Switch on your car's FM-RDS car radio.
8. Set the TA/TP of your car's FM-RDS car radio to 'Off' and ensure that its display is
set to show station names.
9. Manually tune your car radio to FM 87.60Mhz and store this frequency on a
convenient preset button.
10. Turn the volume control to a moderate listening level. In UK you will hear mainly
hiss.

Kinetic
®
digitizor
TM
M-DAB 0001 User Guide
13
11. Plug digitizor's cigar lighter type plug into a working 12V D cigar lighter socket.
The indicator LED on the digitizor box will glow red and, after a few seconds, the
hiss from your radio will cease.
12. Secure the digitizor box and tidy the cables AWAY from the digitizor box. Avoid
coiling excess power or aerial cables.
13. digitizor will automatically search for DAB stations and create a station list. The
display will show [FFF N]. FFF denotes the channel currently being scanned, and N
indicates how many stations have been detected.
14. When the scan is complete, digitizor will play the DAB station that is listed first
alphabetically.
15. Your DAB aerial may require internal / phantom power (please refer to your DAB
aerial's instructions), in which case you MUST switch on the aerial power, otherwise
the aerial will not function properly, if at all:
a. Press the remote's 'MENU' button. Your radio’s display shows ‘87.6’.
b. Press the
▼
button repeatedly until 'ANTENNA' shows on your radio's display.
c. Press the
■
button.
d. Press the
▼
button until 'ANT ON' shows on your radio's display.
e. Press the
■
button.
f. Display shows 'DONE'. Aerial power is now 'ON'.
g. Press and hold the DAS button to re-scan for DAB stations.
16. Use the
▲ ▼
buttons to select a DAB station of your choice. Stations may
take a few seconds to tune, depending upon your FM/AM radio. Your digitizor is
now running in AF (Automatic Frequency hange) mode.
17. heck all is working correctly you are ready to enjoy in-car DAB!
18. Please turn to page 16 and check the detailed AF mode User Instructions.

Kinetic
®
digitizor
TM
M-DAB 0001 User Guide
14
WIRELESS ONNE TION SET-UP #2
1. Observe the !!SAFETY FIRST!! on page 2
2. Remove the FM-RDS from the dash of your vehicle. (!!If it has a security code
number, don't forget to check that you know the number before you disconnect
the power!!)
3. hoose a suitable place behind or under the dash to position your digitizor box.
For the best wireless performance, mount digitizor close to the car radio, with
no intervening metal objects.
4. Install a DAB car aerial (available separately) equipped with an SMB(F)
connector and run the cable to the location you have chosen for your digitizor.
Insert the DAB aerial plug into the DAB aerial socket of your digitizor.
5. Leave the two FM/AM aerial leads unconnected with the cap in place on the
male DIN connector.
6. Select the power cable without cigar lighter plug, i.e. the one with bare ends.
7. onnect the red power cable to the switched 12v cable to your FM-RDS radio.
8. onnect the black earth cable to the earth cable to your FM-RDS radio.
9. Set the switch on the side of the digitizor to 'Wireless'.
10. If you want to play an external audio device such as an MP3 player or iPod®
through your car radio, connect a 3.5mm stereo audio cable to digitizor's Auxiliary
Input socket. Route the cable to a convenient position for your external audio
device.
11. Switch on your car's FM-RDS car radio.
12. Set the TA/TP of your car radio to 'Off' and ensure its display is set to show FM
station names.
13. Manually tune your car radio to FM 87.60Mhz. Turn the volume control to a
moderate listening level. In UK you will hear mainly hiss.
14. Insert the power cable plug into the 12V D socket of your digitizor and turn it
gently 90 degrees clockwise to lock it in place. The indicator LED on the digitizor
box will glow red and, after a few seconds, the hiss from your radio will cease.

Kinetic
®
digitizor
TM
M-DAB 0001 User Guide
15
15. digitizor will automatically search for DAB stations and create a station list. The
display will show [FFF N]. FFF denotes the channel currently being scanned,
and N indicates how many stations have been detected.
16. When the scan is complete digitizor will play the DAB station that is listed first
alphabetically.
17. Your DAB aerial may require internal / phantom power (please refer to your
DAB aerial's instructions), in which case you MUST switch on the aerial power,
otherwise the aerial will not function properly, if at all:
a. Press the remote's 'MENU' button. Your radio’s display shows ‘87.6’.
b. Press the
▼
button repeatedly until 'ANTENNA' shows on your radio's display.
c. Press the
■
button.
d. Press the
▼
button until 'ANT ON' shows on your radio's display.
e. Press the
■
button.
f. Display shows 'DONE'. Aerial power is now 'ON'.
g. Press and hold the DAS button to re-scan for DAB stations.
18. Use the
▲ ▼
buttons to select a DAB station of your choice. Stations may
take a few seconds to tune, depending upon your FM/AM radio. Your digitizor is
now running in AF (Automatic Frequency hange) mode.
19. Secure the digitizor box and tidy the cables AWAY from the digitizor box. Avoid
coiling excess power or aerial cables.
20. heck all is working correctly, re-fit the FM-RDS radio and you are ready to
enjoy in-car DAB!
21. Please turn to page 16 and check the detailed AF mode instructions.

Kinetic
®
digitizor
TM
M-DAB 0001 User Guide
16
USE IN AF (AUTOMATI FREQUEN Y HANGE) MODE
digitizor will automatically switch on and commence transmitting each time you turn on
the car ignition.
Turn on your in-car audio system and go to the FM band.
Ensure your car radio's display is set to show FM station names.
Set your car radio AF function to 'on'. If your radio has no AF function, please use
AutoScan mode - see page 18.
If your car radio has TA and/or TP functions set both to 'off'.
Tune the car radio’s FM frequency to FM 87.6 MHz and memorize this frequency on a
convenient preset button. This button is your 'digitizor' preset.
Select DAB stations according to the instructions on page 20.
To listen to FM/AM stations, switch digitizor to standby by pressing the q button once.
To return to DAB, press q again and select the 'digitizor' preset on your car radio.
USTOMISING THE FM TRANSMITTER FOR BEST PERFOMAN E IN AF
MODE
digitizor is equipped with a unique, patented AF (Automatic Frequency hange)
function.
When digitizor identifies the need to switch FM transmission frequency, digitizor's
patented AF will tell the car radio to change FM frequency automatically and the car
radio display will show the new frequency in use.
There are two AF settings, AF _H (High Sensitive) & AF _L (Low Sensitive). The
default setting is AF _L.
1. If the FM frequency automatically changes too often, select AF _L.
2. If FM frequency does not automatically change soon enough, select AF _H.
To change the AF sensitivity:
1. Press MENU followed by ◄◄ or ►► until the display shows [FM MODE].
2. Press
■
followed by ◄◄ or ►► until the display shows [AF _H] or [AF _L].
3. Press
■
to confirm your choice.
For an on demand frequency change, press and hold the FM button for 3 seconds. Your
FM radio display will show [AF Frequency] where 'Frequency' is the new frequency that
digitizor will use and your car radio will tune to that frequency automatically. While a
new transmission frequency operation is in process and [AF Frequency] is displayed.
Depending on your car radio, it may be necessary to press
■
to return the display to

Kinetic
®
digitizor
TM
M-DAB 0001 User Guide
17
Station Name when FM retuning is complete.
!! While the digitizor is changing to a new transmission frequency any key pressed other
than the power key will be ignored by the system !!
If digitizor's FM transmission frequency becomes out of sync with the car radio
frequency:
1. Press the 87.6 FM preset of your car radio or tune manually to 87.6MHz.
2. Press MENU then
■
to reset digitizor's transmission frequency to 87.6MHz.
IF YOUR RADIO DOES NOT FULLY FUN TION WITH AF
The performance of AF depends upon the FM sensitivity of your radio and the AF
software in your radio. If your radio only partly functions with AF , please use AutoScan
mode instead - see page 18.

Kinetic
®
digitizor
TM
M-DAB 0001 User Guide
18
USE IN AUTOS AN MODE
digitizor will automatically switch on and commence transmitting each time you turn on
the car ignition.
Turn on your in-car audio system and go to the FM band.
Ensure your car radio's display is set to show FM station names.
If your car radio has AF, TP and/or TA functions please set all to 'off'.
Tune your car radio and store digitizor's four default FM frequencies (87.6MHz, 92.5MHz,
102.5MHz and 107.9MHz) on four convenient preset buttons.
Tune the car radio to 87.6Mhz.
1. Press MENU followed by ◄◄ or ►► until the display shows [FM MODE].
2. Press
■
followed by ◄◄ or ►► until the display shows [AUTOS AN].
3. Press
■
.
AutoScan mode is now permanently enabled (until you either deliberately switch back to
AF mode or carry out full reset of digitizor.)
Select DAB stations according to the instructions on page 20.
To listen to FM/AM stations switch digitizor to standby by pressing the q button once.
To return to DAB press q again and retune your car radio to digitizor's transmission
frequency.
USTOMISING THE FM TRANSMITTER FOR BEST PERFORMAN E IN
AUTOS AN MODE
As you travel around, digitizor automatically and continuously scans the FM band for
three clear frequencies in the locality and stores them on the FM button.
If you experience interference from an FM radio station, change digitizor's transmission
frequency:
1. Press and hold the FM button, then retune your car radio to the new frequency that
is shown on the display.
or
2. Press the FM button repeatedly to select one of the three clear frequencies [SX
frequency], followed by
■
, then retune your car radio to the new frequency that is
shown on its display.
or
3. hange to one of the four default FM transmission frequencies by pressing the FM
button, then either button number 1 (87.6MHz), 2, (92.5MHz), 3 (102.5MHz) or 4,
(107.9MHz) followed by
■
, then select the appropriate FM radio preset.
Depending on your car radio, it may be necessary to press
■
to return the display to

Kinetic
®
digitizor
TM
M-DAB 0001 User Guide
19
Station Name when FM retuning is complete.
If you wish to change the default transmission frequencies:
1. Press the FM button. The display will show the current FM transmission frequency.
2. Press button 1 - 4 to select the FM frequency that you wish to change.
3. Use ◄◄ or ►► to step the FM frequency up or down by 2MHz or
▲ ▼
or to step
up or down by 100KHz until your chosen FM frequency (e.g. 106.7MHz) is
displayed.
4. Press and hold a preset key (1 to 4) to store the selected frequency. The display will
show [FX SAVED].
5. Store the new FM frequency on the appropriate preset of your car radio.
Saving an FM frequency in the memory does not change the current FM transmission
frequency.
Should you need to reset digitizor's FM transmission frequency:
1. Press the 87.6 FM preset of your car radio or tune manually to 87.6MHz.
2. Press MENU then
■
. digitizor's transmission frequency is reset to 87.6MHz.
!! While digitizor is changing transmission frequency any key pressed other than the
power key will be ignored by the system !!