KING RVM1000 User manual

BLUETOOTH WEATHERPROOF SPEAKER LIGHT
Congratulations on your purchase of this unique and versatile RV Media Bluetooth
Speaker Light.
Designed with the RV enthusiast in mind, this speaker allows you to easily add an
external speaker to your RV using the latest Bluetooth Streaming technology.
Not only suitable for RVs, there are many other uses for this speaker such as: marine
applications, pergolas, pool areas, garages, etc. - anywhere you can mount the
speaker within reach of 12VDC or a 110VAC power adaptor* (sold separately), and
where you would like the added convenience of a super bright LED light!
POWER
Operating Voltage: 12V
100W Max Audio Output Power
LED Power Consumption 0.28A @ 12V
Max Total Power Consumption: 3A @ 12V
Package contents listed on back.
*Manufacturer specied adaptor - KING #RVM50 (input: 110-240 V, 50/60 Hz, 1.5 A max)
BLUETOOTH
Output Power Class 2
Frequency Band 2.4000GHz - 2.4835GHz
Bluetooth 4.0 Specication
Typical Range up to approximately 30 Feet
(if no obstructions)
SPECIFICATIONS
RV INSTALLATION
INSTALLATION IN OTHER LOCATIONS
LOCATION
The RV Media Bluetooth Speaker Light operates on 12VDC and is intended to be installed
on the exterior of your RV, ideally replacing an existing awning light. However, you can
install it anywhere outside or inside the RV as long as you can connect it to 12VDC.
INSTALLATION (see diagram on back of this guide)
If installing in place of an exterior awning light, please use the following steps as a guide:
1. Carefully remove the existing awning light. Disconnect the RV’s wiring from the light
and keep the wiring accessible for the next step.
2. Connect the red wire of the supplied male power lead to the RV’s +12V wire, and
connect the black wire to the RV’s ground wire. Make these connections with
suitable crimp terminals or solder and heat shrink.
3. Mark the location of the 4 mounting screws. Be careful to ensure the screws will not
damage any materials behind the mounting surface.
4. Mount the optional locating brackets using the center screw (only) with the hook part
at the bottom. These brackets provide reinforcement for the speaker plus they can
be used as a temporary, removable mounting option if required.
5. Apply the foam sealing tape around the back edge of the speaker.
6. Plug the female power lead attached to the speaker light into the male power lead
that was wired in step 2. We suggest that this connection be secured with electrical
tape. Mount the speaker using the 4 supplied screws taking care not to overtighten
the screws. Please ensure the wiring is recessed as much as possible in the hole it
emerges from and ensure that any remaining cable is stored in the cavity on the back
of the speaker. Press in the supplied screw covers to hide the screws.
7. To complete the installation, use a suitable RV sealant to seal around the edge of the
speaker to ensure a water tight seal.
NOTE: If you are unsure about any aspects of the installation, please seek the
advice of an experienced RV installation technician or electrician.
For installations in marine applications, home pergolas, pool and entertainment areas
etc., when a direct 12V power source is not available, please use the optional RV Media
110VAC/12VDC power adaptor* (sold separately). The power adaptor converts 110VAC
to the required 12VDC and features an extra long 9 foot power cord to ensure it reaches
the Bluetooth Speaker.
NOTE: The power adaptor should be located in a dry environment.
POWER UP THE SPEAKER LIGHT
To ensure easy operation when the Bluetooth Speaker Light is installed in place of an
awning light, use your RV awning light power switch to turn the Speaker Light on or
off. When the Speaker Light is installed in other locations using the optional 110VAC
to 12VDC power adaptor* (sold separately), please use the speaker’s on/off switch
(located on right hand corner of speaker) to turn the LED light on or off.
BLUETOOTH CONNECTION
The RV Media Bluetooth Speaker Light connects to devices such as Smart Phones
and Tablets using Bluetooth A2DP Audio Streaming technology.
1. When powered on, a red LED at the bottom of the speaker will illuminate to
indicate that it is switched on.
2. Within 3 seconds, the blue LED at the bottom of the speaker will illuminate to
indicate that the Bluetooth receiver is working.
3. If not connected to a Bluetooth transmitter such as a Smart Phone or other
Bluetooth transmitting device, the unit will switch to “discovery” mode waiting for
a Bluetooth connection. The blue LED will ash rapidly to indicate that the unit
is awaiting connection.
4. To connect to the speaker, open the Bluetooth menu on your device and search
for new devices. “RV Media” should be displayed as an available device.
(It may not appear for 15 seconds). Select “RV Media” to initiate connection.
NOTE: You do not need to enter a PIN code to connect a device to this speaker.
5. The blue LED will illuminate to show the connection is in progress and if
successful, it will now ash twice every 5 seconds conrming the device is
connected.
6. Only one device can be connected at a time but a maximum of 8 devices, once
paired, can be stored in memory. This means that a device previously paired will
automatically pair once the speaker is turned on providing the device is within
range. If, for example, a 9th device is paired with the speaker, the oldest device
will be erased and will need to be manually reconnected if used again.
7. Once connected to your device, you can then use your device’s audio controls to
start music playback and control the speaker’s volume level.
8. Audio may also be streamed from many Smart Phone apps such as Internet
Radio Stations, Youtube, video players, etc. This feature is dependent on app
and device capabilities, software and operation system version.
FIRST TIME USE NOTE: To ensure the Bluetooth Speaker Light remembers your
Bluetooth device, it may be necessary to manually disconnect your device from
the speaker on rst use (this is done on your device’s BT menu). This will ensure
it is memorized and therefore should connect automatically for subsequent use.
OPERATION
11200 Hampshire Avenue South, Bloomington, MN 55438
PH 952.922.6889 || FAX [phone] || kingconnect.com
MODELS
RVM1000
RVM1001

TROUBLESHOOTING
LIMITED WARRANTY
CLEANING
Most connection problems can be xed by manually disconnecting and reconnecting your
Bluetooth device to the RV Media Bluetooth Speaker Light.
CONNECTION SECURITY
While this device does not need a PIN code to allow devices to connect to it, your
connection is secure and cannot be disturbed by other nearby Bluetooth devices.
Once you have turned on the Bluetooth Speaker Light and connected your Bluetooth
device, the speaker ceases being in “discovery” mode and will not be visible to other
Bluetooth devices, ensuring your Bluetooth connection with the speaker is uninterrupted.
If while using the speaker, you want to connect a different device to it, it is suggested you
use the following procedure:
a) Turn off the speaker.
b) Turn off Bluetooth on the device that had been connected to the speaker.
c) Turn on the speaker and connect the new device to it.
NOTE: The reason you need to turn off Bluetooth on the original device is that the speaker
may connect to it rst (when you turn it back on) rather than the new device. Once the
new device is connected, you can turn on Bluetooth again on the original device.
This system ensures you have a secure connection between your devices and the
speaker that cannot be interrupted by nearby Bluetooth devices.
While the RV Media Bluetooth Speaker Light is fully waterproof, it is recommended that
when cleaning your RV with a pressure washer or high pressure hose that it be covered
with a plastic bag and taped to the edge of the speaker.
The RV Media Speaker Light is covered by a one year parts limited warranty from the date of original
purchase. The customer is not responsible for the cost of replacement parts if the original part is determined
to be defective under the terms of the warranty. The customer is responsible for the cost of replacement
parts after one year.
Only KING may perform warranty evaluations and repairs. Depending upon the problem, KING may
authorize a dealer to perform the necessary repairs. Any labor expense outside of that performed at the
factory is not covered under this warranty.
Should any trouble develop during the warranty period, contact KING at [phone]. You must contact
KING before the warranty period expires. The customer must supply proof of purchase (such as a dated
sales receipt) when requesting warranty service. If the customer cannot supply proof of purchase, warranty
period shall start 30 days after date of manufacture.
If it is determined that the unit needs to be returned to KING, customer must return COMPLETE product,
freight prepaid, to: KING, 11200 Hampshire Avenue South, Bloomington, MN 55438.
If inspection shows the trouble is caused by defective workmanship or material, KING will repair
(or at its option, replace) without charge.
When returning product, KING will supply an RMA number (Return Merchandise Authorization).
This number must be clearly written on the box. Failure to clearly write RMA number on box will result in
delays in processing claim. Along with product, the customer should include in the box: name, address,
daytime phone number, proof of purchase and description of the problem.
This warranty does not cover installation and external wiring, or remanufactured units. This warranty is not
transferable from the original owner. This warranty also does not apply where:
• The product has been abused, misused, improperly installed or improperly maintained.
• Repairs have been made or attempted by others that are not certied by KING to do such repairs.
• Repairs are required because of normal wear and tear.
• Alterations have been made to the product or the unit has been opened without authorization.
• Damage has been caused by power washing.
• Circumstances beyond the control of KING cause the product to no longer operate correctly.
In no event shall KING be liable for any indirect, incidental, or consequential damages from the sale or use
of the product. This disclaimer applies both during and after the term of the warranty.
KING disclaims liability for any implied warranties, including implied warranties of “merchantability” and
“tness for a specic purpose,” after the one year term of this warranty.
This warranty gives you specic legal rights, and you may also have other rights, which vary from state to
state. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation or exclusion may not apply to you. Some states do not allow limitations on how long an
implied warranty lasts, so the above limitation may not apply to you.
RV Media Speaker Light Package Contents
1 x Bluetooth Speaker Light 2 x Mounting Brackets
6 x Mounting Screws 1 x 12V Power Lead
4 x Screw Covers 1 x Setup Guide/Warranty
Foam sealing tape
The Bluetooth word mark and logos are owned by the Bluetooth SIG, inc and any use of such
marks by RV Media is under license. Other trademarks and trade names are those of their
respective owners.
As RV Media will continually strive to improve our products, specications and design are
subject to change without notice. Please dispose of thoughtfully recognizing local regulations.
MADE IN CHINA FCC ID: 2AGDW0006V1
KING is a registered trademark of Electronic Controlled Systems, Inc.
©2015 KING 22257 Rev A
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
Please take attention that changes or modication not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This equipment should be installed and operated with a minimum distance of 8 inches between the radiator and
your body.