Kingfisher FS2GL User manual

Gliding Bench
Instruction Manual
CODE: FS2GL
PBL - NG8 4GP
B1511P/A
FS2GL Instructions.indd 3 11/11/2015 12:02

Thank you for purchasing this Kingsher Gliding Bench. Made from the nest materials and with expert
precision. Please ensure that you read these instructions and that all parts are present before proceeding with the
assembly of this product.
IMPORTANT, PLEASE RETAIN FOR FUTURE REFERENCE: READ CAREFULLY!
Read and follow the instrucons and safety informaon before using this product for the rst me.
Any errors made in following the instrucons may result in serious injury. Keep all instrucons in a safe place for future use. When using equipment, a few safety
precauons must be observed to avoid injuries and damage. Please read the complete instrucons with due care. Keep this manual in a safe place, so that the
informaon is available at all mes. If you give the equipment to any other person, give them these instrucons as well. We accept no liability for damage or
accidents which arise due to non-observance of these instrucons and the safety informaon.
WARNING! – DO NOT LEAVE CHILDREN UNATENDED ON OR BESIDE THE BENCH
WARNING! – THIS PRODUCT INCLUDES SMALL PARTS (E.G. SCREWS, NUTS, WAHSERS). TO AVOID POSSIBLE CHOKING HAZARD, USE EXTREME CAUTION
WHEN ASSEMBLING THIS PRODUCT NEAR CHILDREN UNDER THREE YEARS OF AGE AND PETS.
WARNING! – DO NOT USE YOUR BENCH AS A STEP STOOL
WARNING! – DO NOT SIT ON THE EDGE OF THE SEAT, ARMRESTS OR ON THE BACKREST AS THIS COULD MAKE THE BENCH TIP OVER OR DAMAGE THE GLIDING
MECHANISM
CAUTION! – ADULT ASSEMBLY REQUIRED; MAY REQUIRE TWO PEOPLE
SAFETY
THIS PRODUCT IS INTENDED FOR DOMESTIC, (NON-COMMERCIAL, NON-INDUSTRIAL) OUTDOOR USE BY PERSONS AND OBJECTS WITHIN THE LOAD CAPACITIES
STATED BELOW.
ALWAYS USE THE FURNITURE SET ON A FLAT, LEVEL AND STABLE SURFACE.
AVOID FINGERS OR CLOTHING FROM BECOMING TRAPPED BETWEEN PARTS OF THE CHAIR.
DO NOT JUMP ON OR USE EXCESSIVE FORCE WITH THESE PRODUCTS.
DO NOT LEAVE THIS PRODUCT EXPOSED TO ADVERSE WEATHER CONDITIONS. WE RECOMMEND THAT YOU USE A COVER OR STORE AWAY DURING PERIODS OF
BAD WEATHER TO PROTECT YOUR FURNITURE.
DO NOT ALLOW CHILDREN TO CLIMB ON THIS PRODUCT.
IT IS ADVISED THAT YOU ONLY USE THIS PRODUCT IN THE CORRECT MANNER, WE DO NOT ACCEPT RESPONSIBILITY FOR MISUSE OR SUBSEQUENT DAMAGE.
MAX WEIGHT CAPACITY: 180KG PER SEAT
DO NOT DRAG THE GLIDER CHAIR ACROSS THE GROUND.
WE RECOMMMEND TWO PEOPLE LIFT THE TABLE WHEN MOVING IT.
MAINTENANCE
INSPECT THIS PRODUCT AT LEAST ONCE A MONTH PAYING SPECIAL ATTENTION TO NUTS AND BOLTS. TIGHTEN UP ALL LOOSE FITTINGS.
WIPE AWAY SPILLS IMEDIATELY.
Care Instrucons:
• Brush o loose dirt
• Hose Down
• Clean with mixture of water and mild or natural soap
• Use so bristle brush to clean
• Rinse thoroughly
• Air dry
• Do not bleach
• Do not use detergents
RUST ON METAL SURFACES
RUST IS UNAVOIDABLE WHEN METAL PARTS ARE USED OUTDOORS. RUST IS THE CHEMICAL REACTION BETWEEN OXYGEN, WATER AND METAL.
TO HELP AVOID RUST:
• KEEP METAL OUTDOOR FURNITURE OUT OF BAD WEATHER AS MUCH AS POSSIBLE;
• AVOID KNOCKING METAL PARTS AGAINST EACH OTHER OR DRAGGING ITEMS ACROSS A CONCRETE OR TILE FLOOR. EACH DAMAGED
AREA IN THE METAL IS PLACE FOR OXYGEN AND WATER TO CONTACT THE METAL AND BEGIN RUST FORMATION;
• EVERY THREE TO FOUR WEEKS AND BEFORE STORING, WASH METAL PARTS WITH SOAPY WATER, USING A SOFT BRUSH IN THE
CREVICES. RINSE THOROUGHLY, DRY COMPLETELY, AND THEN COAT THE METAL WITH CAR WAX OF YOUR CHOICE. THIS TEMPORARELY
PROTECTS THE METAL FROM OXYGEN AND WATER IN THE AIR. AS THE COATING IS THIN, IT MUST BE REPLENISHED PERIODICALLY TO
RETAIN ITS PROTECTIVE QUALITIES.
STORAGE
TO PREVENT MILDEW FORMATION, ENSURE ALL THE PARTS ARE DRY BEFORE PUTTING AWAY FOR STORAGE. STORE IN COOL, DRY LOCATION
OUT OF TRAFFICE AREAS TO AVOID TRIPPING HAZARD.
FS2GL Instructions.indd 4 11/11/2015 12:02

A
B
C
D
E
1
2
3
4
5
6
7
X2
X1
X2
X2
X2
X4
X8
X4
X2
X2
X20
X33
LEG
LEG BRACE
GLIDING BAR
ARM REST/SIDE
SEAT/BACK REST
SMALL NUTS/BOLTS
MEDIUM NUTS/BOLTS
LARGE NUTS/BOLTS
LARGE BOLTS
SPACER
NUT CAPS
SCREW HEAD CAPS
Parts
A A
B
CC
D
D
E
1
2
34
65
7
FS2GL Instructions.indd 5 11/11/2015 12:02

Assemble 1x(A) and 1x(B) using 2x(1)
as shown above.
Assemble 1x(A) and 1x(B) using 2x(1)
as shown above.
1 2
3
Attach 1x(C) to the pre-assembled part
from step 2 using 1x(2) at one end and
1x(2) at the other. Ensure that the end of
(C) that you attached is the circle end.
Repeat Step 3 to attach the remaining
1x(C) inbetween the previously attached
(C) and (B) using 1x(2) at each end.
Ensure that you tighten all the ttings
before proceeding to the next stage.
4
A
A
A
A
A
B
B
BB
1
1
1
1
C
C
C
2 2
FS2GL Instructions.indd 6 11/11/2015 12:02

The unit should look as shown above
at this stage of the assembly. Please
ensure that you tighten all the ttings
before proceeding to the next stage.
Attach 1x(D) using 2x(2) to the ends of
each of the parts (C). Ensure that the
straighter edge of (D) is at the same end
as (B).
Place the main seating unit (E) onto the
pre-assembled unit as shown above.
Ensure that holes on (E) marry up with
the holes on the pre-assembled unit.
7
5
8
6
Repeat Step 5 for the opposite side of
the unit.
BB
22
D
D
E
C
C
FS2GL Instructions.indd 7 11/11/2015 12:02

Repeat Step 10 at the opposite end.
Secure the top of (D) to the back rest of
(E). Insert 1x(4) through (D) then place
1x(5) over the thread. Once (5) is in place
gently tighten the remaining thread of (4)
into the hole on (E).
10
11 12
9
Repeat Step 11 to attached the opposite
end as shown above. Ensure that you
tighten all the ttings before proceeding
to the next stage.
Attach one end of (E) to one of the (D)
ends as shown above using 2x(3).
E
E E
3
3
3
3
D
D D
D
4
4
4 4
5
5
5 5
FS2GL Instructions.indd 8 11/11/2015 12:02

Place (7) over the nuts on the pre-
assembled unit until all the nuts are
covered.
Finally ensure that the unit secure and all ttings are securely fastened. If you are
satied that the unit is safe to use. Place the assembled unit in your chosen location
and enjoy.
Place (6) over the screw heads on the
pre-assembled unit until all the screw
heads are covered.
13
15
14
6
7
FS2GL Instructions.indd 9 11/11/2015 12:02

Gliding Bench
Instruction Manual
CODE: FS2GL
PBL - NG8 4GP
B1511P/A
FS2GL Instructions.indd 2 11/11/2015 12:02