Kinghome GJC22BN-D3NRNC5P User manual

Thank you for choosing our product.
Please read this Owner’s Manual carefully before operation and
retain it for future reference.
If you have lost the Owner’s Manual, please contact the local agent
or visit www.gree.com or send an email to  for
the electronic version.
Owner's Manual
Original Instructions
Window Type Air Conditioner

GJC22BN-D3NRNC5P
GJC24BN-D3NRNC5L
GJC24BN-D3NRNC5M
GJC24BN-D3NRNC5P
GJC24BN-D3NRND2L
GJC24BN-D3NRND2M
GJC24BN-D3NRNE2M
GJC25BN-D3NRNC5P
GJC28BN-D3NRNC5P
GJC24BN-D3NRND2P
GJC22BN-D3NRND2P

Operation and Maintenance Installation
Contents
Operation Notices
Precautions.....................................4
Parts Name.....................................5
Operation Guide
Function and Control.......................6
Introduction of remote controller ....9
Instruction for fan direction
adjusting.........................................12
Maintenance
Clean and Maintenance.................13
Malfunction
Malfunction analysis......................14
Installation Notice
Installation and Maintenance.........17
Preparation before installation.......19
Installation
Window types installation and
requirements .................................20
READ THIS MANUAL
Inside you will find many helpful hints on how to use and maintain your air conditioner
properly. Just a little preventive care on your part can save you a great deal of time and
money over the life of your air conditioner. You'll find many answers to common problems
in the chart of troubleshooting tips. If you review our chart of Troubleshooting Tips first,
you may not need to call for service at all.
!
Contact the authorized service technician for repair or maintenance of this unit.
Contact the installer for installation of this unit.
The air conditioner is not intended for use by young children or infirm persons without
supervision.
Young children should be supervised to ensure that they do not play with the air
conditioner.
If the power cord is to be replaced, replacement work must be performed by
authorized personnel only.
Installation work must be performed in accordance with the national wiring standards
by authorized personnel only.
CAUTION
Safety Precautions..........................1
Sponge Sticking Method
and Procedures.............................29
Thru-The-Wall Installation .............30
Installation procedure.....................21

This appliance is not intended for use by persons (including children) with reduc-
ed physical, sensory or mental capabilities or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the ap-
pliance by a person responsible for their safety. Children should be supervised to
ensure they are away from the appliance.
This appliance can be used by children aged from 8 years and above and persons
with reduced physical,sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of
the appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision.
When refrigerant leaks or requires discharge during installation, maintenance, or
disassembly, it should be handled by certified professionals or otherwise in com-
pliance with local laws and regulations.

1
Do not disassemble or modify unit.
.SIHTODREVEN
.SIHTODSYAWLA
ƽ.wolebnwohssaeralaunamsihtnidesuslobmysfogninaeM
!
GNINRAW
Plug in power plug properly
! Do not operate or stop the unit by
inserting or pulling out the power plug.
Do not damage or use an
unspecified power cord.
Do not modify power cord length or
share the outlet with other appliances.
! rosdnahtewhtiwetarepotonoD
in damp environment.
Do not direct airflow at room
occupants only.
Always ensure effective grounding.
,sdnuosegnartsfitinuehtgulpnU
smell, or smoke comes from it.
Keep firearms away.
Do not allow water to run into
electric parts.
roesoolsitifitekcosehtesutonoD
damaged.
Do not use the power cord close to
heating appliances.
dnarekaerbtiu
cricllatsnisyawlA
a dedicated power circuit.
Do not open the unit during
operation.
Do not use the power cord near
flammable gas or combustibles, such as
gasoline, benzene, thinner, etc.
!
!
!
ƽ.erifesuacyamtI ƽ.kcohscirtcelednaerifesuacyamtI ƽ.erifronoisolpxenaesuacyamtI
ƽ.kcohscirtceleesuacyamtI
ƽIncorrect installation may cause fire
.kcohscirtceledna
ƽ.htlaehruoyegamaddluocsihT
ƽti,degamadsidrocrewopehtfI
must be replaced by the
manufacturer or an authorized
service center in order to avoid
hazard.
ƽ.kcohscirtcelednaerifesuacyamtI
ƽIt may cause failure of machine or
electric shock.
ƽ.kcohscirtceleesuacyamtI
ƽIt may cause electric shock or fire due
to heat generation.
ƽ.kcohscirtcelednaerifesuacyamtI
ƽIncorrect grounding may cause
electric shock.
ƽIt may cause electric shock or fire
.noitarenegtaehoteud
ƽOtherwise, it may cause electric
shock or fire due to excess heat
generation.
Ventilate room before operating air conditioner if there
.ecnailpparehtonamorfegakaelsagasi
!
ƽ.snrubdnaerif,noisolpxeesuacyamtI ƽ.kcohscirtcelednaeruliafesuacyamtI
Safety Precautions
Indicates a hazardous situation that, if not avoided, will
result in death or serious injury.
Indicates a hazardous situation that, if not avoided, could
result in death or serious injury.
Indicates a hazardous situation that, if not avoided, may
result in minor or moderate injury.
Indicates important but not hazard-related information,
used to indicate risk of property damage.
Indicates a hazard that would be assigned a signal word
WARNING or CAUTION.
WARNING
CAUTION
DANGER
NOTICE

2
If water enters the unit, turn the unit off at the power
outlet and switch off the circuit breaker. Isolate supply
by taking the power plug out and contact a
qualified service technician.
CAUTION
When the air filter is to be
removed, do not touch the metal
parts ofthe unit.
Do not clean the air conditioner
with water.
Ventilate the room well when used
together with a stove, etc.
When the unit is to be cleaned,
switch off, and turn off the
circuit breaker.
!
!
Do not put a pet or house plant
where it will be exposed to direct
air flow.
Do not use for special purposes.
Stop operation and close the
window in storm or hurricane.
Do not place obstacles around
air-inlets or inside of air-outlet.
Do not use strong detergent such as
wax or thinner but use a soft cloth.
Hold the plug by the head of the
power plug when taking it out.
Ensure that the installation bracket
of the outdoor appliance is not
damages due to prolonged exposure.
Do not place heavy object on the
power cord and ensure that the
power cord is not compressed.
Turn off the main power switch
when not using the unit for
a long time.
Always insert the filters securely.
Clean the filter once every
two weeks.
Do not drink water drained from
air conditioner.
●Appearance may be deteriorated due
to change of product color or
scratching of its surface.
●There is danger of fire or electric shock. ●It contains contaminants and could
make you sick.
●Operation without filters may cause
failure.
●Do not use this air conditioner to
preserve precision devices, food,
pets, plants, and art objects. It may
cause deterioration of quality, etc.
●It may cause failure of product or fire.
●An oxygen shortage may occur.
●If bracket is damaged, there is concern
of damage due to falling of unit.
●It may cause electric shock and
damage.
●This could injure the pet or plant.
●Water may enter the unit and degrade
the insulation. It may cause an electric
shock.
●It may cause failure of appliance or
accident.
●Operation with windows opened may
cause wetting of indoor and soaking
of household furniture.
●Do not clean unit when power is on
as it may cause fire and electric
shock, it may cause an injury.
●It may cause an injury.
Use caution when unpacking and installing.
Sharp edges could cause injury.
!
!
!
!
Safety Precautions

3
Operation of Current Device
Please contact Customer Service.
with a new cord - please
contact Customer Service.
“
”
CAUTION:
CAUTION
Safety Precautions

4
Precautions
RESET
TEST
WARNING
 Air Conditioner should be properly grounded. Incorrect grounding may cause
electric shock.
purpose socket. Otherwise, it may cause
 
r, otherwise the remote controller
may be broken.

o not spray water on air conditioner. It may cause electric shock or malunction.
personal injury or damage.
r, or put heavy objects. It may cause damage or
personal injury.
n.
ing air conditioner. Otherwise, it may
cause electric shock.


 ctrical leakage
ic shock or damage.
Please contact dealer when you need to repair air conditioner.
cause personal injury or damage.
protection when installing the air conditioner.
Note:

protection device. There're test button and reset
button on the plug. You are suggested to check
the power cord periodically.
Check method:
r, indicator is ON.

you can heard a sound. Then press reset button,
indicator will be ON, which indicates the protection
device is normal.
Indicator
Note: Plug may be di
actual product. 
product.
Working temperature range
 
  
o


5
Parts Name
Control
panel
Air outlet frame
Fan direction
adjusting rod
Air-in panel
Power cord
NOTE: Panel outlook picture,just for reference, please take the real unit as standard.

6
 After putting through the power, air conditioner will give out a sound and indic-
ators on control panel will be on. After that, you operate the air conditioner
through remote controller or control panel.
Function and Control
Cooling indicator
SE indicator
Fan indicator
Dry indicator




Auto speed indicator
High speed indicator
Medium speed indicator
Low speed indicator
Power button
Mode button
Fan Speed button
Timer button
Filter check button


Display




Light indicates the unit
is in the temperature or
delay time Set mode.
Ŀ/ ŀbutton

7
Mode button
Press this button can your required operation mode in turn. Corresponding
indicator will be on.
 Under this mode, air conditioner operates under cooling mode. Cooling
indicator will be on. Press “Fan Speed” button can adjust the fan speed.
 Under this mode, the unit will operate automatically according to
ex-factory setting. In this case, set temperature cannot be adjusted.
 Under this mode, air conditioner operates under SE mode. SE
indicator will be on. Press “Fan Speed” button can adjust the fan speed.
 Under this mode, air conditioner will not cool or heat, only blow
wind. Fan indicator will be on. Press “Fan Speed” button can adjust the fan
speed. (No auto fan speed under fan mode)
Under this mode, the unit runs in low fan speed for dehumidification and
the corresponding indicator is on; under dry mode, the fan speed cannot be
adjusted.
Dry
CoolAuto Fan
Only
Energy
Saver

Press this button can turn on or turn of
 Press this button to turn on air conditioner, the unit will operate in Energy Save
mode; if the unit is energized after power failure, the unit will still operate according
to the status before power failure.
f air conditioner.

Press this button can select your required fan speed in turn. Corresponding
speed indicator will be on.
AutoHighMedLow

"#"$
 Can be set under off state of unit. If timer ON reaches, the system will
run according to the preset mode and fan speed. The setting range is 0.5~24hr.
 Can be set under on state of unit. If timer OFF reaches, the unit will
When user cleaned the filter, press Filter check button to clear the opera-
turn off. The timer can be set in 0.5 hour increment below 10 hours and in 1 hour
increment for 10 hours or above.
After fan rotates for 250h totally, lamp of cleaning filter is on to remind customer
clean it.
tion time. Meanwhile, the warning indicator will turn off.

8
/ button
Under temperature setting status, after each pressing of “ ” or “ ” button,
temperature will increase or decrease 1°F(°C). Temperature setting range: 61~86°F
(16~30°C). Under timer setting status, after each pressing of “ ” or “ ” button,
time will increase or decrease 0.5h or 1h.
Display
1. Under ON status without timer setting, the operation mode is Auto, Cool,
Energy Saver or Dry mode, and the set temperature will be displayed.
2. Under ON status without timer setting, the operation mode is fan mode and
the ambient temperature will be displayed.
3. Time will be displayed under timer setting or timer preview.
Ŀŀ
Ŀŀ
Ŀŀ

9
ON/OFF button
MODE button

FAN button
I FEEL button
SLEEP button
+ / - button
TIMER button
ON/OFF button
MODE button
2
3
5
7
6
4
3
1
Each time you press the button, a mode is selected in a sequence that goes from
AUTO, COOL, SAVE, FAN and DRY, as the following:
COOLAUTO DRYFANSAVE
Press this button to turn on the unit,turning on the unit with remote controller, the
unit will operate in energy-saving mode. Press this button again to turn off the unit.
NOTE: If energize the unit, turn it on, turn it off and then turn it on, the unit will operate
in energy-saving mode; if the unit is energized after power failure, the unit will still
operate according to the status before power failure.Under off status, the complete
unit doesn’t respond to turning on the unit with remote controller under any mode other
than energy-saving mode. In this case, the buzzer will give out two sounds for error
indication. You need to turn off the unit and then turn it on with remote controller or
switch to energy-saving mode after turning on the unit with remote controller.
Note:
This is a general use remote controller, it could be used for the air conditioners
with multifunction; For some function, which the model GRHVQ¶W have, if press the
corresponding button on the remote controller that the unit will keep the original
running status.
Introduction of remote controller

10
- / + button
Under timer setting status, after each pressing of “+” or “-” button, time will
Pressing + or - button once will increase or decrease set temperature by 1°F(°C).
Hold + or - button for 2s, set temperature on remote controller will change quickly.
Release the button after your required set temperature is reached.
increase or decrease 0.5h . Hold “ +” or “-” button, 2s later, time displayed
on dual-8 nixie tube will change quickly. Loosen the button until the time is
reached to your set time.


FAN button
This button is used for setting Fan Speed in the sequence that goes from AUTO,
I FEEL button
I feel function will be action if pressing this button. If controller receives I FEEL
SLEEP button
TIMER button
Press this button to go into the SLEEP operation mode. Press it again to cancel
Press this button to initiate auto-on/auto-off timer. To cancel auto-timer program,
press this button twice.
this function. This function is available in COOL, HEAT (Only for models with
heating function) or DRY mode to maintain the most comfortable temperature
for you.
order, it will work under ambient temperature value which sending by remote
controller, and remote controller will send ambient temperature value to
controller every 10min. After 11min, if controller does not receive ambient
temperature value which sending by remote controller, it will run with AC ambient
temperature; if I FEEL is not set, ambient temperature will adopt sampling
value of AC temperature sensor. If power off happens, this function will not be
memorized.
NOTE: There are 3 speeds for the Fan Speed of this model, Speed 4 is the same
with speed 3.
, , , to then back to Auto.
Auto
Speed 1 Speed 2 Speed 3
Speed 4(unavailable in this air conditioner)

11
Replacement of Batteries in Remote Controller
1. Press the mark “ ” on back cover of batteries box cover for remote controller with
fingers as shown in the fig, and then remove the batteries box cover along the arrow
direction. Battery
Cover of battery box
Remove
Reinstall
2. Replace with two #7 (AAA 1.5V) dry batteries.
Make sure positions for “+” pole and “-” pole are
correct.
3. Reinstall batteries box cover.
Note:
The distance between signal sender and receiving window should be no more
than 8m, and there should be no obstacles between them.

conditioner when using the remote controller.
Replace new batteries of the same model when replacement is required.
When you don’t use remote controller for a long time, please take out the
batteries.

12
Instruction for fan direction adjusting
You can adjust the fan direction adjusting rod to select left&right air outlet dire-
ction according to your requirement.
You can adjust the air outlet frame to select up&down air outlet direction acc-
ording to your requirement.
Fan direction adjusting rod
Air outlet frame

13
Clean and Maintenance
WARNING
 Turn off the air conditioner and disconnect the power before cleaning the air
conditioner to avoid electric shock.
ater to avoid electric shock.
air conditioner.
1. Open the panel
Pull the groove at both sides of panel forcibly to open
(below 45 degree) dissolved with neutral abluent,
and then put it under the shady place.
NOTICE:
ation environment, you can increase the clean times.
Clean the panel
If the surface of panel is very dirty, you are suggested to use soft dry cloth or wet
cloth dipped with neutral abluent to wipe it.
Note: leaning it.
Maintain the outer case
You are suggested to check the outer case of air conditioner one or twice every
year. If the outer case is damaged or rusted, please contact dealer.
Note: In order to reduce damage or rust under no-use season, you can cover
the air conditioner with protective covering.

14
Malfunction analysis
General phenomenon analysis
Please check below items before asking for maintenance. If the problem still
can't be solved, please contact dealer or professional person.
Phenomenon Troubleshooting Solution
Air conditioner
can't operate
 Wait after power recovery.
 

of

Ask professional person to replace



 Ask professional person to replace


 W
 The protection device for the
f

again. If the power tripps off again



nance person.
Poor cooling
(heating)
 W

  
w are
 w.
Air conditioner
can't receive
signal from
remote controller
or remote
controller is not
sensible.

seriosly (sch as static presse,






 The receiving range of remote
controller is 8m. Do not exceed
this range.

 



controller. If the power is low,
please replace the batteries.


to air conditioner.
and try it again.

15
No fan blowed
out from air
conditioner

blocked? 
t






r



Set temperature

 under
auto mode?
 


eter te required temperature


 
-
ff 





r
r


Y


turned of

r

Y

"PAPA"

turned of



Malfunction code
rr
e
Malfunction code Solution
1 
2 
4 
J 









16
 If there's below phenomenon, please turn off the air conditioner and disconnect
the power immediately. After that, please contact dealer at once.



y.
W

WARNING