KIP 2050 User manual
KIP
SCANNERS
SCANNERS
SCANNERS
SCANNERS
2000 Series SCSI
Scanners
KIP 2050 / KIP 2080
KIP 2120
User's
Manual
Ver E.2
A75UMCON (Ver. E.2) 1
We highly appreciate your purchasing our Image Scanner K-75 series (KIP2050, 2080, 2120 and
2160).
This USER'S MANUAL contains functional and operational explanation of the Image Scanner K-75
series.
Read this USER'S MANUAL carefully before use in order to understand the K-75 series fully and to use
more efficiently.
Keep this USER'S MANUAL for future reference.
1. When K-75 series is installed in U.S.A.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
2. When K-75 series is installed in Europe
This equipment complies with the requirements in Pub.22 of CISPR Rules for a Class B computing
device.
Operation of this equipment in a residential area may cause unacceptable interference to radio and
TV reception requiring the operator to take whatever steps are necessary to correct the interference.
Do not install Machine around electronics equipment or precision instruments.
It may be influenced by electrical reason or vibration while printing.
If Machine is installed near electronics equipment, such as TV or radio, interference to
equipment, such as noise or flickering may be occurred.
Use separate power line and install Machine as far as such equipment.
A75UMCON (Ver. E.2) 2
WARNINGS FOR THE SAFETY (OBSERVE THESE WARNING)
Following warnings are very important to use this equipment safely and to prevent the operator from
danger and his/her property from being damaged.
Hazardous or damage degree is classified and shown as follows when this machine is erroneously
used ignoring this USER'S MANUAL.
WARNING
This caution mark denotes that the failure to follow given instructions in handling
the machine could result in a death or serious injury.
CAUTION
This caution mark denotes that the failure to follow given instructions in handling
the machine could result in an injury or physical damage only.
This symbol signifies what must not be done.
This symbol signifies General Mandatory Action.
A75UMCON (Ver. E.2) 3
WARNINGS
1. Power source should be rated from 100V to 240V plus or minus 10%, more
than 6A and 50/60Hz.
2. It is preferable that the used power circuit is provided with a dedicated
breaker.
3. Install the machine as close as possible to the outlet.
4. When you wish to move the machine to another place, make sure to ask
your service engineer.
Connect the scanner and Ground with each other surely with the grounding
wire.
Otherwise, it is dangerous for you if you receive an electric shock or at the time
of lightning.
If the outlet does not have a Grounding Terminal or if it is impossible to connect,
call the vendor or service professional for the installation.
Do not disassemble or tamper the machine. Otherwise, it may cause a fire
or receiving an electric shock.
1. Do not use a multi-wiring connector that might raise the temperature of
the outlet abnormally and cause a fire.
2. Do not put anything heavy on the power cord. It may cause a fire or
receiving an electric shock.
3. Do not step on the power cord, and do not damage or process it. It may also
cause a fire or receiving an electric shock.
4. Do not tie the power cord or make a knot on it. It may also cause a fire or
receiving an electric shock.
5. Do not put a flower vase, a flowerpot or a water-filled glass on the top of the
machine. If the water spilt out, it may also cause a fire or receiving an
electric shock.
1. If the machine generates abnormal smell or noise, turn it off and then
disconnect the power plug from the outlet necessarily.
2. Do not handle the power plug with the wet hand positively. It may cause to
receive an electric shock.
3. Insert the power plug into the outlet completely. If the power plug is not
inserted completely, it may cause a fire.
4. Use only the attached power cord.
Make sure to catch the Plug when you unplug the machine.
Otherwise, you may break the cord and may result in a fire or receiving an
electric shock.
A75UMCON (Ver. E.2) 4
CAUTIONS
Do not install the machine at the following places.
1. Humidified or dusty place.
2. Unstable floor.
When the machine comes down, it may cause the injury.
1. Unplug the machine before you move it to another place. Otherwise, the
power cord may be damaged and may result in a fire or receiving an electric
shock.
2. If nobody operates the scanner in the night time, make sure to turn it off for
the safety.
3. If nobody operates the machine for a long time during consecutive holidays,
make sure to turn it off for the safety.
4. Nothing should be put near the power plug so as to disconnect it quickly
anytime.
Be careful not to catch your hand between Upper Unit and Main Unit when you
close the Upper Unit.
A75UMCON (Ver. E.2) 5
TABLE OF CONTENTS
Chapter 1 Before Use
Page
1.1 Required Conditions for the Installation Place 1- 1
1.2 Originals Prohibited to Copy 1- 2
1.2.1 Prohibited items by the law 1- 2
1.2.2 Special items to be cared 1- 2
1.2.3 Items protected by the copyright 1- 2
1.3 Features 1- 3
1.4 Specifications 1- 4
1.5 Name of Each Part and Its Function 1- 5
1.5.1 Front view 1- 5
1.5.2 Rear view 1- 5
1.5.3 Operation Panel 1- 6
1.6 Power Indicator and Ready Indicator 1- 7
1.7 Warning Indications 1- 7
1.8 How to Operate the LCD 1- 9
1.9 Difference of Action at the Time of Memory Full 1-12
1.10 Scan Mode 1-13
Chapter 2 Simple Copying
Page
2.1 Turning on the Scanner 2- 1
2.2 Applicable Original 2- 3
2.3 Explanation for Copy Job 2- 4
2.4 Setting the Original to the Scanner 2- 6
2.5 Copying by the Roll Media Feeding 2- 8
2.6 Copying by the Sheet Media Feeding 2-11
2.7 Pre-scan 2-15
2.8 Treatment against Roll Empty during Copying 2-17
2.8.1 Another Roll Deck has same roll media 2-17
2.8.2 No Roll Deck has same roll media 2-18
2.9 Turning off the Scanner 2-19
A75UMCON (Ver. E.2) 6
Chapter 3 Operation
Page
3.1 Introduction 3- 1
3.2 Basic Screen 3- 2
3.2.1 Copy Count setting (Number of copies) 3- 5
3.3 Copying Media Settings 3- 6
3.3.1 Roll media feeding 3- 7
A. Automatic roll selection (Auto Paper Mode) 3- 7
B. Manual roll selection 3-10
3.3.2 Sheet media feeding 3-11
A. Automatic sheet size selection (Auto Sheet Size Mode) 3-11
B. Manual sheet size selection 3-15
3.3.3 Cut Modes 3-17
A. Synchro Cut 3-17
B. Standard Cut 3-19
3.3.4 Divide Mode 3-22
3.4 Zoom Settings 3-27
3.4.1 Auto Zoom Mode 3-28
A. In case of the roll media feeding 3-28
B. In case of the sheet media feeding 3-31
3.4.2 Standard Zoom Ratio 3-33
3.4.3 % Mode (Direct selection of percentage) 3-35
3.4.5 Media Size Mode (Ratio between original size and media size) 3-37
3.4.6 Zoom Program Mode 3-38
3.4.7 XY Zoom Mode 3-40
3.5 Image Quality Settings 3-44
3.5.1 Selecting original’s image type 3-45
3.5.2 Background Mode 3-47
3.5.3 Despeckle Mode
3-51
3.5.4 Threshold 3-54
A. Function of Threshold Level in the Line Mode 3-56
B. Function of Threshold Level in the Line/Photo Mode 3-58
C. Function of Threshold Level in the Photo Mode 3-60
3.5.5 Sharpness 3-62
3.5.6 Density 3-64
3.6 Function Settings 3-66
3.6.1 Shift and Centering 3-67
A. Shift 3-68
B. Centering 3-71
3.6.2 Leading Edge and Trailing Edge 3-73
3.6.3 Folder Setting 3-79
3.6.4 Mirror Image Mode 3-80
3.6.5 Negative Image Mode 3-82
3.7 Date Stamp Settings 3-84
3.7.1 How to print the Date Stamp 3-85
3.7.2 Main position of Date Stamp 3-90
3.7.3 Rotation of Date Stamp 3-91
3.7.4 Horizontal shift and vertical shift of Date Stamp 3-92
3.7.5 Order of date and time 3-95
3.7.6 Type of Date Stamp 3-96
A75UMCON (Ver. E.2) 7
3.8 Set Copy Mode 3-98
3.8.1 Explanation for Set Copt Job 3-100
3.8.2 Set Copy in the Layout Mode 3-102
3.8.3 Set Copy in the Sort Mode 3-112
3.8.4 Concurrent Print Mode (Check Set) 3-120
3.9 Mode Memory 3-121
3.9.1 Calling the Mode Memory 3-122
3.10 Menu Settings 3-124
3.10.1 Original 3-125
3.10.2 Edit Function 3-129
A. Re-edit 3-131
B. Delete 3-133
C. Insert 3-135
D. Replace 3-138
E. All Cancel 3-141
3.10.3 Setting 3-142
A. How to register the setting 3-143
B. Register Zoom Ratio 3-145
C. Original Format 3-148
D. Auto Start 3-149
E. Standard Mode 3-151
F. Mode Memory (Creation and deletion of Mode Memory) 3-157
G. Memory 3-161
H. Date / Time 3-163
I. SCSI 3-165
3.10.4 Command 3-167
A. Initial Cut 3-168
B. Wire Cleaning 3-170
C. Information 3-171
3.11 Reference Screen 3-173
3.12 Power Save Function 3-176
3.13 Scanner Power Save 3-178
3.14 Auto Reset Function 3-179
3.15 Interrupt Mode 3-180
3.16 Reset 3-181
3.17 Re-copy 3-182
3.18 Sample Copy 3-184
3.19 Rotate Mode 3-185
Chapter 4 Error Indications and Treatments
Page
4.1 Error Message and Treatments 4-1
A75UMCON (Ver. E.2) 8
Chapter 5 Maintenance and Adjustments
Page
5.1 Usual Maintenance 5- 1
5.2 LCD Adjustments 5- 4
5.2.1 LCD contrast adjustment 5- 4
5.2.2 Touch panel positioning 5- 6
5.3 Pin Layout and Rating of Interface Connector 5- 9
A75UM1E1 (Ver. E.2)
Chapter 1
Before Use
Page
1.1 Required Conditions for the Installation Place 1- 1
1.2 Originals Prohibited to Copy 1- 2
1.2.1 Prohibited items by the law 1- 2
1.2.2 Special items to be cared 1- 2
1.2.3 Items protected by the copyright 1- 2
1.3 Features 1- 3
1.4 Specifications 1- 4
1.5 Name of Each Part and Its Function 1- 5
1.5.1 Front view 1- 5
1.5.2 Rear view 1- 5
1.5.3 Operation Panel 1- 6
1.6 Power Indicator and Ready Indicator 1- 7
1.7 Warning Indications 1- 7
1.8 How to Operate the LCD 1- 9
1.9 Difference of Action at the Time of Memory Full 1-12
1.10 Scan Mode 1-13
A75UM1E1 (Ver. E.2) 1-1
1.1 Required Conditions for the Installation Place
Following conditions have to be satisfied.
1. The power source should be rated from 100V to 240V plus or minus 10%, more than 6A and
50 or 60Hz.
Scanner’s voltage condition is automatically corresponded to the voltage of outlet (from
100V to 240V) if only you connect the power plug.
2. Make sure to connect the power plug to the outlet that is provided with the Ground Terminal.
The outlet must be corresponded to 3 pins power plug.
3. To completely disconnect the equipment from the power source, please draw the power
plug from the outlet.
The outlet must be easily accessible near the equipment.
4. The temperature must be within the range from 10 to 32.5 degrees centigrade, and the
humidity must be from 20% to 80%.
5. Prevent the equipment from fire, dust and direct sunlight.
If it is impossible to avoid the direct sunlight, please pull the curtain to intercept the sunlight.
6. Machine Noise Information Ordinance 3. GSGV January 18, 1991 :
The maximum sound pressure level is equal or less than 70dB (A) according to ISO 7779.
7. The floor must be enough strong to withstand machine’s weight.
8. Keep enough space around the machine as follows.
Note : Parenthesized numbers are required space to scan the original of 0.12mm or thicker.
60cm or
more
160cm or more
100cm (200cm) or more
60cm or
more
A75UM1E1 (Ver. E.2) 1-2
1.2 Originals Prohibited to Copy
It is not necessarily allowed to copy every kind of original.
You may be punished by the law if only you possess the copy of some kind of original.
We recommend you to consider enough before you copy such original.
1.2.1 Prohibited items by the law
1. It is not allowed to copy Currency (Bill, Money, Bank Note, etc.), Government issued Negotiable
Instruments (National Bonds, Security, Local Debt Bonds, etc.).
2. It is not allowed to copy Foreign Currency or Foreign Negotiable Instruments.
3. It is not allowed to copy unused postal stamps or government postcards without permission to
make replica from Government,
4. It is not allowed to copy Government issued revenue stamps, certificate stamps which are
prescribed by Liquor Tax Act or the Commodity Tax Act.
1.2.2 Special items to be cared
1. It is warned by the government to copy private issued securities (stock certificate, draft, check,
goods ticket, etc.), commutation ticket or book of tickets, excluding that some specific company
copies such originals as many as it requires for its own business.
2. We recommend you not to copy freely such originals as government issued passport, public or
private issued licenses, automobile inspection certification, Ids and tickets like pass or meal.
Reference Law Prohibited items to copy
Regulations to control fake currency and bond. Currency (Bill, Money, Bank Note, etc.),
Government issued Negotiable Instruments
(National Bonds, Security, Local Debt Bonds,
etc.)
Control Law against Forged & faked Foreign
Currency, Bill, Bank Note and Bond
Foreign Currency or Foreign Negotiable
Instruments
Forged postal stamps control law Unused postal stamps or government postcards
Forged revenue stamps control law Government issued revenue stamps, and
certificate
stamps prescribed by Liquor Tax Act or
Commodity Tax Act
Currency similarity securities Control Law Private issued securities (stock, draft, check,
goods ticket, etc.), commutation or book tickets
1.2.3 Items protected by the copyright
It is prohibited to copy such originals as book, music, paintings, printed copy, maps, drawings, movie
and pictures which are protected by the copyright, except for personnel or family use or similar
purpose.
A75UM1E1 (Ver. E.2) 1-3
1.3 Features
An image scanner for a large original
K-75 series is available to scan 36 inches wide original in maximum.
The scanning speed is any of 50.95mm (per a second), 80mm, 120mm and 160mm.
When you connect the K-75 series with such digital printers as KIP1230E, KIP2720E, KIP3620E,
and KIP9010, they will work as a digital copier.
The following are combination of scanner and printer in same speed.
Scanner Printer Speed
KIP2050 - 50.95mm/sec.
KIP2080 KIP2720E 80mm/sec.
KIP2120 KIP3620E and KIP1230E 120mm/sec.
KIP2160 KIP9010 160mm/sec.
Fine quality of image scanning
400 dpi scanner head is used.
Scanned images such as letters and diagrams are copied clearly with fine quality.
Level of reading density (Threshold Level) is adjustable.
Since K-75 series has 17 Threshold Levels, it is possible to select the best level for reading
original’s image.
It is also possible to select the Threshold Level by automatic selection.
Scanned image is compensated by the loaded software.
Halftone images are expressed in the pseudo gray scale by this software.
Reduction, enlargement and multiple sheets of copying
Since the memory is installed, it is possible to adjust the zoom ratio from 25.0% to 400.0% in 0.1%
increment.
Also it is possible to do a multiple sheets of copying up to 999 sheets for one original at one time.
Abundant interface function
Parallel Terminals are provided for printer’s output and computer’s input and output.
Space and energy saving design
K-75 series is formed as a compact desktop type with a rationalized design.
Therefore, it is possible to install it in a small space in the office.
K-75 series has Power Save Modes so as not to consume so much power when no operation is
done.
Storing multiple Copy Jobs to the memory (Pre-scan)
Even if the connected printer is not ready, it is possible to scan originals and store the scanned
image data in the memory as Copy Jobs if memory capacity allows.
Other functions
(1) Image shift (Horizontal shift : Shift and Centering)
(Vertical shift : Leading Edge and Trailing Edge)
(2) Automatic original size detection
(3) Set Copy Mode
(4) Date Stamp Mode
(5) Mirror Image Mode
(6) Negative Image Mode
(7) Auto Zoom Mode
(8) Auto Paper Mode
A75UM1E1 (Ver. E.2) 1-4
1.4 Specifications
Model KIP2050, KIP2080, KIP2120 or KIP2160
Scanning method Sheet through type
Reading sensor Silicone-CCD
Light source Cold Cathode Ray Tube
Maximum reading width 914.4mm
Reading speed KIP2050 : 50.95mm (per a second)
KIP2080 : 80mm
KIP2120 : 120mm
KIP2160 : 160mm
Resolution 400DPI
Tone Line, Line/Photo and Photo
Interface KIP IF- 8 (For printer)
RS232C
SCSI-2 (Option)
Memory capacity From 64MB (standard) to 320MB (option)
Power consumption 190W
Environmental conditions Temperature
From 10 to 32.5 degrees centigrade
Humidity
From 20% to 80% (No dew)
Acoustic noise Less than 60db
Outer dimension 1,368mm (Width) x 489mm (Depth) x 266mm (Height)
Weight About 76kg
Power source Voltage
From 100 to 240V plus or minus 10%
Note : Scanner’s voltage condition is automatically corresponded
to the voltage of outlet (from 100V to 240V) if only you
connect the power plug.
Frequency
50 or 60Hz
Original thickness 0.05mm to 1.6mm (50g to 120g/centare)
Note : When you scan an original which is thicker than 0.12mm,
make sure to select 50% or larger zoom ratio.
Note : We may change these specifications without noticing to you.
A75UM1E1 (Ver. E.2) 1-5
1.5 Name of Each Part and Its Function
1.5.1 Front view
1.5.2 Rear view
RS232C
SCSI
Interface 8
Ground
(Option)
Operation Panel
Original Guide
Original Table
Lever
Power Switch
Trays
Move the original along the Original
Guide to avoid original's skewing.
Pull up the Lever to unlock
and open the Upper Unit.
Original Receivers
A75UM1E1 (Ver. E.2) 1-6
1.5.3 Operation Panel
1. Menu Key
2. Reference Key
3. Basic Screen Key
4. Mode Memory Key
5. Paper Key
6. Function Key
7. Zoom Key
8. Date Stamp Key
9. Image Quality Key
10. Layout/Sort Key
11. +/R Key
12. -/L Key
13. Ten Keys
14. Clear Key
15. Start Key
16. Stop/Eject Key
17. Sample Key
18. Re-copy Key
19. Rotate Key
20. Auto Paper Key
21. Reset Key
22. Concurrent Print Key
23. Interrupt Key
24. Power Save Key
25. Set Copy Key
26. Auto Zoom Key
/L
/R
12345678910 13 15
18
17
16
26 25 24 23 22 21 20 19
11 12 14
IMAGE QUALITY
LAYOUT/SORT
ZOOM
DATE STAMP
PAPER
FUNCTION
BASIC SCREEN
MODE ME MORY
MENU
REFERENCE
SET COPY PRINT
CONCURRENT
RESET
INTERRUPT
POWER
SAVE
AUTO PAP ERAUTO ZOOM
ROTATE
RE COPY
SAMPL E
STOP/
EJECT
START
0
1
4
7
.
2
5
8
C
3
6
9
A75UM1E1 (Ver. E.2) 1-7
1.6 Power Indicator and Ready Indicator
Power Indicator
The Power Indicator lights up with green when you turn on the machine.
Ready Indicator
The Ready Indicator blinks when the printer is warming up (not ready).
It lights up when the printer gets ready for copying.
It is put out when some error occurs on either scanner or printer.
1.7 Warning Indications
Roll Empty Indicator
The Roll End Indicator lights up with red when the selected roll media is emptied.
Making reference to printer’s manual, load a new roll media to the Roll Deck.
Toner Low Indicator
The Toner Low Indicator lights up with red when the printer has used up all toner.
Making reference to printer’s manual, supply the toner to the printer.
Web Empty Indicator
The Web Empty Indicator blinks with red when the Web in the printer is emptied.
Call your service engineer to make him/her replace the Web when this indicator
blinks.
If the connected printer is not equipped with the Web, the Web Empty Indicator does
not work.
A75UM1E1 (Ver. E.2) 1-8
Error Indicator
The Error Indicator lights up with red when the printer has some error.
Some Error Message is indicated on the LCD at this time as the following figure.
Refer to "Error Message and Treatments" on page 4-1.
Error Message
Mis-feed Indicator
The Mis-feed Indicator lights up with red at the time of media mis-feed in the printer.
Remove the copying media making reference to printer’s manual.
Waste Toner Full Indicator
The Waste Toner Full Indicator lights up with red when the Waste Toner Bottle of the
printer is filled with the toner.
Making reference to printer’s manual, replace the bottle with the new one.
If the printer is not equipped with the sensor to detect the quantity of toner in the
bottle, the Waste Toner Full Indicator does not work.
MENU BASIC SCREEN PAPER ZOOM IMAGE QUALITY
0%
001
Paper Zoom Image
Quality
1:36"
100.0%
Synchro
Line
Background
[Threshold]
Auto
Plain Paper
Upper unit is open
A75UM1E1 (Ver. E.2) 1-9
1.8 How to Operate the LCD
If you push some of keys (A) below the LCD, the corresponding setting screen is indicated on the LCD.
If you push the Paper Key (B), for example, the Paper Setting Screen is indicated which concerns to
the settings of copying media as the following right figure.
Several setting items are indicated in each setting screen.
Settings are done pressing the setting item.
The following are examples for operation.
1. When you have some selectable items as “Roll” in the Paper Setting Screen, it is possible to
choose one of them pressing it.
If the item is selected, it is colored showing it is valid now.
Example : You press [3 : 24” Plain Paper].
/L
/R
LAYOUT/SORT
IMAGE QUALITY
ZOOM
DATE STAMP
PAPER
FUNCTION
BASIC SCREEN
MODE MEMORY
MENU
REFERENCE
POWER
SAVE
SET COPY
AUTO ZOOM
A
B
0%
001
Roll
1:36"
Plain Paper
2:30"
Plain Paper
3:24"
Plain Paper
4:18"
Plain Paper
Bypass
Cut Mode
Synchro
Standard
Div i de
Size
IMAGE QUALITYZOOMPAPERBASIC SCREENMENU
48"
44"
42"
36"
34"
30"
24"
22"
18"
17"
12"
11"
9"
8.5"
0%
001
Roll Cut Mode Size
2:30"
Vellum
1:36"
Plain Paper
3:24"
Film
4:18"
Plain Paper
Bypass
Synchro
Standard
Divide
48"
44"
42"
36"
34"
30"
24"
22"
18"
17"
12"
11"
9"
8.5"
0%
001
Roll Cut Mode Size
2:30"
Vellum
1:36"
Plain Paper
3:24"
Film
4:18"
Plain Paper
Bypass
Synchro
Standard
Divide
48"
44"
42"
36"
34"
30"
24"
22"
18"
17"
12"
11"
9"
8.5"
A75UM1E1 (Ver. E.2) 1-10
2. If the setting value is indicated in the setting screen and its frame is thick, it is possible to change
that setting value.
If some setting values are indicated as the following Zoom Setting Screen and you wish to change
one of them, press the setting value that you will change in order to make its frame thick.
Example : You press 7.0” to make it possible to change.
3. If , , and are indicated in the setting screen, it is possible to increase or decrease the
framed setting value pressing them.
Example : You change the zoom ratio from 100.0% to 99.0% pressing .
0%
001
Mode Program
%
Media
Size
Zoom
Program
XY Zoom
Original Copy
70.0%
10.0" 7.0"
0%
001
Mode Program
%
Media
Size
Zoom
Program
XY Zoom
Original Copy
70.0%
10.0" 7.0"
0%
001
Mode Program
%
Media
Size
Zoom
Program
XY Zoom
100.0%
Reduce 100% Enlarge
0%
001
Mode Program
%
Media
Size
Zoom
Program
XY Zoom
99.0%
Reduce 100% Enlarge
This manual suits for next models
2
Table of contents
Other KIP Scanner manuals
