Kitchen and Home 5-ZG-36-SS User manual

1
Instruction Manual
Built-In Gas Cooktop
5-ZG-36-SS, 5-ZG-36-SS-LPG 5-ZSS-36X, 5-ZSS-36X-LPG
4-GCW, 4-GCW-LPG 5-GCW, 5-GCW-LPG
2-GCW , 2-GCW-LPG 2-SSW , 2-SSW-LPG

2
BEFORE YOU BEGIN
Read this manual completely and carefully. Installation of this cooktop must conform with local codes, or in
the absence of local codes, with the National Fuel Gas Code. This appliance is ETL certified by Intertek.
Note to Consumer:
Keep the manual for future reference.
This appliance must be properly grounded.
- Proper installation is the responsibility of the installer..
- Product failure due to improper installation is not covered under the Warranty.
- Remove all tape and packaging..
- Make sure the burners are properly seated and level..
- Take the accessory pack out of the packing.
- Check to be sure that no cooktop parts have come loose during shipping.
- IMPORTANT – Observe all governing codes and ordinances.
NOTICE
−Prior to installation, make sure gas and pressure supplied is compatible with the appliance settings
−Settings of this appliance are stated on the rating label.
− This gas cooktop is not connected to a combustion products evacuation device. Particular attention
shall be given to the relevant requirement regarding ventilation.
− Use of this gas cooktop will produce heat, moisture and products of combustion. Ensure that the
kitchen is well ventilated. Keep a window open or install a mechanical ventilation device.

3
Contents
1. Close-up view......................................................................................04
2. Using your cooktop............................................................................05
3. Cleaning…………………………………................................................06
4. Useful tips…….....................................................................................07
5. Troubleshooting…...............................................................................08
6. Installation ….................……………....................................................09
7. Burners and nozzle specifications ...................................................13
8. Different types of gas ….....................................................................15

4
Congratulations for choosing this appliance, which you will find dependable and very easy to use.
This manual will explain how to achieve the best performance and also extend the life of your appliance.
Thank you
Close-up View
5-ZG-36-SS, 5-ZG-36-SS-LPG, 5-ZSS-36X, 5-ZSS-36X-LPG
5-GCW, 5-GCW-LPG
4-GCW, 4-GCW-LPG 2-GCW , 2-GCW-LPG , 2-SSW , 2-SSW-LPG

5
1. Small burner
2. Medium burner
3. Large burner
4. X Large wok burner
5. Ignitor
6. Safety device - If the flame accidentally goes out (spills, drafts, etc.), it stops the delivery
of gas to the burner.
7. Control knobs
Using your cooktop
Gas Burners
Position of the corresponding gas burner is indicated on each control knob.
Burners are different in size and power. Choose the most appropriate one for the diameter of the cookware
being used.
Each burner has following settings:
OFF
High
Low
Our cooktops are equipped with a safety device
The knob must be kept pressed for about 6 seconds after ignition until the flame/temperature has been
detected.
Ignition switch is integrated in the control knob.
To ignite a burner: Simply press the corresponding knob and turn it in the counter-clockwise direction
to the high setting and keep pressed until the burner is lit.
Caution: If the flame goes out accidentally, turn off the gas using the control knob and wait at least 1
minute before restarting it.
To turn off a burner: Turn the knob in the clockwise direction until it stops at the OFF position.

6
Cleaning
Before cleaning or performing maintenance of your gas cooktop, you must disconnect it from the electrical
power supply (electrical outlet or battery).
To make sure your cooktop performs properly and safely for a long time, it is extremely
important to clean it carefully, thoroughly and often.
Please keep in mind the following:
●The enameled parts and the glass top must be washed with warm water without using abrasive powders
or corrosive substances which would cause damage.
●The removable parts of the burners should be washed usually with warm water and dish soap, make
sure to remove baked-on substances;
●Automatic ignition pin must be cleaned often and carefully..
●Stainless steel top plate and other SS parts should be cleaned with water/soap combo or approved SS
cleaners.
●After each use, the glass surface should be cleaned with a damp cloth to remove dust or food residue.
Glass should be cleaned regularly with warm water and mild dish soap.
●Accidental spills must be cleaned immediately to prevent further damage. If something is melted on top
the surface, it is OK to use scraper/razor blade to remove it but you must be careful not to scratch the
surface itself (Fig 1).
Do not use abrasive sponges or chemically aggressive cleaners, like oven sprays and stain removers
(Fig.2);
Fig.1 Fig.2
Lubricating the gas valves
Over the time, gas valves may become stuck, making them difficult to operate. In this case, a licensed
technician should clean the inside of valve and lubricate it.

7
Useful tips
Using the burners
For best performance, follow these general guidelines:
● Use the appropriate cookware for each burner (see table) in order to prevent the flame from reaching the
side of the pot or pan.
● Always use cookware with a flat bottom and keep the lid on.
Burner Ø Cookware diameter (cm)
Small burner 10~14
Medium burner 16~20
Large burner 22~24
X large wok burner 24~26
● The cookware bottom diameter must be the same or larger than diameter of the burner being used.
● Do not use the same cookware for gas and electric burners. High concentrated heat produced by gas
cooktops can deform the bottom of the pot. Therefore, you will not achieve the best physical
contact/results when using these pots on the ceramic glass surface.

8
Troubleshooting
First, check and confirm there are no interruptions to the gas and electrical lines.
The burner can’t be ignited or the flame is not uniform around the burner.
Check to make sure that:
● The gas holes on the burner are not clogged.
● All of the removable parts that make up the burner are placed properly.
● There is no excessive air flow around the cooking surface.
The burner ignites but won’t stay lit.
Check to make sure that:
● You press the knob all the way;
● You keep the knob pressed long enough to activate the thermal switch.
● The gas holes on the burner next to thermal switch are not clogged
The flame goes out when knob is on "Low" setting.
Check to make sure that:
● The gas holes on the burner are not clogged.
● There is no excessive air flow around the cooking surface.
● The minimum has been adjusted correctly (see the section titled "Minimum Regulation").
The cookware is not stable.
Check to make sure that:
● The bottom of the cookware is perfectly flat.
● The cookware is centered correctly on the burner..
● The support grids have not been inverted.
If you have checked all of the above and the cooktop still does not work properly, please call Customer
Service and provide:
● Detailed description of problem.
● Cooktop model number
● Your name
● Date and place of purchase

9
Installation
Our cooktops are sold all over the world and due to different regulations, we strongly recommend that
installation or any type of service is done by a certified technician that is familiar with local codes in your
area
IN THE COMMONWEALTH OF MASSACHUSETTS
This product must be installed by a licensed plumber or gas fitter. When using ball type gas shut-off valves,
they shall be the T-handle type. A flexible gas connector, when used, must not exceed 3 feet in length.
FOR YOUR SAFETY WARNING
If the information in this manual is not followed exactly, a fire or explosion may result causing property
damage, personal injury or death. Do not store or use combustible materials, gasoline or other flammable
vapors and liquids in the vicinity of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS
Do not try to light any appliance. Do not touch any electrical switches, Do not use any phone in your
building. Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier instructions.
If you cannot contact your gas supplier, call the fire department. Installation and service must be performed
by a qualified installer, service agency or the gas supplier.
Countertop cut out requirements
Model Opening size
5-ZG-36-SS
5-ZG-36-SS-LPG
5-ZSS-36X
5-ZSS-36X-LPG
840x480mm
4-GCW, 4GCW-LPG
5-GCW, 5-GCW-LPG
560x480mm
2-SSW, 2-SSW-LPG
2-GCW, 2-GCW-LPG
270x480mm

10
Installation Instructions
The following instructions are for the qualified installer, so the installation and maintenance procedures can
be done in the most professional and expert manner.
Important: Unplug the electrical connection before performing any maintenance work.
Positioning of gas cooktop
Important: this unit may be installed and used only in permanently ventilated rooms.
Requirements that must be followed:
● The room must be equipped with a ventilation system which would evacuate smoke and combustion
gases.
● This is to be done by hood or electric ventilator.
● The room must have sufficient air flow to allow proper combustion. Air flow can not be less than 2 m³/h
per kW of installed capacity. The air supply duct should have diameter of minimum 4”.
● Room can also be vented indirectly through adjacent rooms that have ventilation ducts to the outside.
Adjacent Room Room to be Vented
●I n case of prolonged use of the gas cooktop, it is recommended to intensify ventilation by opening
windows or increasing the power of the air intake and exhaust system (if present).
● Rooms where LPG tanks are installed must be equipped with ventilation to the outside. Tanks must be
kept away from any heating source.

11
Installation of built-in gas cooktop
● Cooktop can be installed in a kitchen, dinning room or any other dry room.
● Included hardware (hooks, screws) will secure the cooktop to surrounding surfaces, 20 to 40 mm in
thickness
Hook position for Hook position for Hook position for
H=20mm top H=30mm top H=40mm top
● When the gas cooktop is not installed on a built-in oven, a wooden panel must be inserted for insulation.
● This panel must be placed at least 20 mm away from the bottom of cooktop.

12
Important:
● If the cooktop is being installed on a built-in oven, the oven should be placed on two wooden strips and if
placed on interior cabinet surface, remember to leave an opening of at least 45 x 560 mm from the back
side.
● When installed on a built-in oven without forced ventilation, air inlets and outlets are required for proper
cabinet ventilation.
Gas connection for gas hob
Gas appliance should always be connected to the gas supply by an authorized installer. During installation
it is essential to install an approved gas valve to isolate the supply from the appliance for future needs.
Connection must be done in accordance with the local regulating laws and make sure cooktop is preset to
be used with same kind of gas that is being supplied/connected.
Important: The pressure regulator that is included with your appliance is adjustable and has been
preset to your cooktop. It MUST be attached to the cooktop and used regardless of the gas source.
If your gas source is a LPG tank, a standard pressure regulator MUST be present as well at the tank
outlet.
Important: For safety and proper functioning of the appliance, gas pressure must conform to the
specifications given in table 1 "Burners and Nozzle Specifications".
Connection to non-flexible tube
(copper or steel)
● Connection to the gas source must be done in such a way as to not to create any stress points to any
part of the gas cooktop.
● Cooktop is supplied with an adjustable "L" shape connector and a gasket.
● Connector should be dismounted and the gasket must be replaced.
●
Gas feeding connector is threaded 1/2”.

13
Connection to flexible steel tube
● Gas feeding connector is threaded 1/2" for round gas pipe. Only use pipes and gaskets that conform to
the current standards.
● The maximum length of the flexible pipes must not exceed 2000mm/79.74”.
● Once the connection has been done, make sure that the flexible metal tube does not touch any moving
parts..
Check the Seal
● After the appliance is installed, check for leaks to ensure all the connections are properly sealed.
● Use a soapy water to test, never use flame.
Electrical Connection
● Appliance is equipped with standard 110V plug used in NorthAmerica.
Table1: Burners and Nozzle Specifications
Adjusting your cooktop to different types of gas
● Inside the package, you will find an extra set of burner nozzles necessary for the gas type conversion.
● Keep them with your manual and if you ever need to switch to a different gas type, you will have the
proper nozzles to do it.
● Switching gas source/replacing nozzles and properly adjusting them is a delicate task and should always
be performed by a certified technician.
● Pressure regulator supplied is adjustable and MUST be properly set when different nozzles are installed.
After the conversion to another gas type is done, make sure you’ve placed a label containing that
information on the appliance.
NG LPG
Burner Burner
Capacities（B
TU）
Nozzle 1/100
(mm) Burner
Capacities（BTU）Nozzle 1/100 (mm)
Small 2800 75 2800 53
Medium 5000 100 5000 68
Large 6500 115 6500 79
X Large 9500 130 9500 93
Supply pressure 12.5mbar 25mbar

14
Valve adjustment
● Valve adjustment should be done with the control knob set at Burner ON small/low flame position.
● Remove the knob, and adjust the flame with a tiny screwdriver.
To check the adjusted flame, start the burner and run it in the high setting for 10 minutes. Then turn the
knob into the low setting. The flame should not extinguish nor move to the nozzle. If it does, readjust the
valves.
Flame selection
● As the burners are adjusted correctly, the flame should be light blue, and the inner flame should be clear.
● The size of flame depends on the position of the related control knob.
● High/Low settings
Burner ON, High Burner ON, Low Burner OFF
● The burner should be on high setting during the initial phase of cooking to bring food to boil quickly.
● Then it should be on low setting to maintain the cooking temperature.
Never operate your cooktop with control knob set between the Burner OFF and Burner ON/High
positions.
● High amount of energy can be conserved when the cooktop is used correctly with appropriate cookware
Up to 60% by using proper size cookware.
Up to 60% when correct heat setting is used.
● It is essential for efficient and energy-saving operation that the burners are kept clean at all times (in
particular the flame slots and nozzles).

15
Different types of gas
TABLE 2: Settings for different types of gas
Pressure Nozzle
diameter Nominal Charge Reduced Charge
Burner NG mbar 1/100mm g/h l/h
BTU
kcal/h kW kcal/h
NG 12.5 75 — 76 2800
702 0.40 344
Small LPG 25 53 66.5 —
2800
702 0.40 34
NG 12.5 100 — 134 5000
1268 0.60 516
Medium LPG 25 68 119 —
5000
1268 0.60 516
NG 12.5 115 — 183 6500
1694 0.90 774
Large LPG 25 79 156 —
6500
1694 0.90 774
NG 12.5 130 — 260 9500
2374 1.50 1290
X Large LPG 25 93 224 —
9500
2374 1.50 1290