Klëarvue Cabinetry 478-3812 User manual

1
LOW DRAWER KIT
Instructions for SKUs: 478-3812, 478-3814
KIT INCLUDES:
Bracket A x2
478-9804
Bumper x2
478-9833
Drawer support
bracket x1
478-9831
Bracket B x2
478-9805
Left glide x1
478-9810
Right glide x1
478-9811
1/4" x 1/2"
Euro screw x10
478-9835
3/16" x 1-3/16"
Long screw x1
478-9832
3/16" x 5/8"
Short screw x3
478-9803
Drawer box x1
Drawer box cover
cap x2
478-9830
To find all Klëarvue Cabinetry®installation instructions and installation videos, visit www.klearvuecabinetry.com.

2
Important: Please read before you begin your drawer installation.
Take note of your cabinet configuration.
STANDARD DRAWER INSTALLATION
• If your configuration features a low drawer kit in one of the locations shaded below, the drawer front will be
attached using bracket B.
• If your configuration features a low drawer kit in the location shaded below, the drawer front will be attached using
bracket A.
• All interior drawers will be attached using bracket A regardless of drawer location. See page 6 for interior drawer
installation.
STEP 1:
• Install bracket A or B (478-9804/478-9805) to the back of the drawer front.
• Line up the holes on the brackets with the pre-drilled holes on the drawer front and secure with the euro screws
(478-9835). The 5” drawer fronts used with low drawer kits are symmetrical and do not have a designated “right
side up” when screwing in the brackets.
478-9835 478-9835
478-9804
478-9805
BRACKET A BRACKET B
BRACKET A BRACKET B

3
STEP 2:
• Install the long screw (478-9832) through the back of the drawer box into the drawer bottom. This helps to add
stability to your drawer kit.
STEP 3:
• Attach the drawer front to the drawer box by lining up the brackets with the slots in the drawer box. Push until you
hear a “click” on both the left and right side. If the drawer front does not “click” into place, verify that the spring
loaded latch is in the open position by placing a Phillips screwdriver into the drawer removal hole and turning
towards the back of the drawer. See page 7 for drawer front removal.
478-9832

4
STEP 4:
• Turn the drawer box upside down and mark the center of the drawer front.
• Use a center punch to make an indent within the three moulded holes on the bracket as shown in the illustration.
STEP 5:
• Use a Phillips screwdriver and the three short screws (478-9803) to fasten the bracket to the drawer bottom.
478-9831
478-9831
478-9831
478-9831
478-9803
478-9803

5
STEP 6:
• For the installation location of the drawer glides, reference the “Drawer Configuration Guide” that was packaged
with your drawer kit.
• Line up the holes of the glide (478-9810/478-9811) with the holes in the cabinet box and secure with the euro
screws (478-9835).
• The drawer glides should be marked left (L) and right (R).
STEP 7:
• To install the drawer box, begin by fully extending both left and right drawer glides.
• Set the drawer box down onto the glides, covering as much of the drawer glide as possible. The drawer box should
be able to support itself on the drawer glides when you let go.
• Quickly and firmly push the drawer into the cabinet box. You should hear a “click” noise as this action will
automatically attach the drawer box to the glides. If the drawer box does not “click”, repeat Step 7. You may not
have pushed the drawer glides hard enough.
• Drawer kits are rated to hold 70 lbs. of weight.
Quick, firm push
478-9810
478-9835
24” Depth
478-9811
478-9835

6
INTERIOR DRAWER INSTALLATION
Interior drawers follow the same steps as a standard drawer, with some minor modifications.
STEP 1:
• Install bracket A (478-9804) to the back of the drawer front. Be sure that the tab of the bracket with two holes is
facing toward the bottom of the drawer front, as pictured below.
• Line up the holes on the brackets with the pre-drilled holes on the interior drawer front and secure with euro screws
(478-9835).
STEP 2:
• Follow STANDARD DRAWER INSTALLATION Steps 2-5 to assemble your interior drawer box.
STEP 3:
• For the installation location of the drawer glides, reference the “Drawer Configuration Guide” that was packaged
with your drawer kit.
• Line up the holes of the glide (478-9810/478-9811) with the holes in the cabinet box. For interior drawers, the glides
are set back behind the first set of pre-drilled holes in the cabinet box.
STEP 4:
• Follow STANDARD DRAWER INSTALLATION Step 7 to install the drawer into the cabinet box.
• If done correctly, the interior drawer front should be flush with the face of your cabinet box. If not, make sure the
holes are lined up per INTERIOR DRAWER INSTALLATION Step 3.
478-9811
478-9835
BRACKET A
BRACKET A
478-9835
478-9804

7
DRAWER ADJUSTMENT AND REMOVAL
A-up/down
adjustment
B-left/right
adjustment
C- release the
drawer box
from the
glides
D- remove the
drawer front
ADJUSTMENT:
A) Turn the metal adjustment screw to adjust the
drawer front up and down.
B) Adjusting your drawer fronts to the left and right
can be a little tricky. To make adjustments, you
will adjust the white adjustment screw inward
and outward of your drawer kit by using a
Phillips screwdriver. Protrude both adjustment
screws to the right to force the drawer front
to move to the left. Protrude both adjustment
screws to the left to force the drawer front to
move to the right.
REMOVAL:
C) To release the drawer box from the drawer
glides, begin by placing your hands under the
center of the drawer front. Be careful not to
place hands under the drawer glides. From the
closed position, use gentle force to extend the
drawer completely out and then lift upwards in
one fluid motion.
D) To remove the drawer front, use a Phillips
screwdriver into the hollowed-out location
(looks like a + symbol) and rotate towards the
back of the drawer box until the bracket is
released. Repeat on both left and right sides
of the drawer. Note: If the white screw on the
mounting bracket has been adjusted and is
protruding out, you may need to un-adjust the
screw to remove or re-install the drawer front.