KLANG:technologies Vier User manual

1
STEP
2
STEP
3
STEP
4
STEP
5
STEP
6
STEP
USE 3D MIXES
Dante Controller
SOURCE
Ch 01 in
Ch 02 in
Ch 03 in
Ch 04 in
Ch 01 Ch 02 Ch 03
1 OPEN again
2 Adjust the GAIN Select switch:
In-Ears: -12 or 0dB
Other: 0 or +12dB.
3Adjust the volume for mix on OUTPUT:01.
4 Go to CONFIG/CHANNELS and set
colors, icons and choose names.
5 Create a 3D headphone mix and enjoy!
Read the next page for further setups.
Register your product: www.KLANG.com/register
Also visit: www.KLANG.com/vier
IEM Transmitter
CONNECTIONS
PAGE 1/2
vier
K4XYZXYZ
192.168.1.50
Power Switch
110–240VAC
Network lights start flashing.
1 Plug in power cord
and switch on.
Front LED lights up in
white while booting and turns purple when ready.
2 Connect your
headphones
to OUTPUT:1.
3 Connect your computer
to Dante ethernet port.
| QUICK START
1OPEN www.KLANG.com/app
2 Download & Install
.
3 Turn o WiFi on your computer and
start .
4 Choose from list or go to CONFIG then
to CONNECT and choose your device.
Problems? Hit the refresh button. Otherwise, set up
dante switch configuration: www.KLANG.com/vlan
or use the NET port instead of Dante port.
SOURCE
1OPEN www.KLANG.com/dante
2Install Dante Virtual Soundcard (DVS)
(free trial license available).
3Start Dante Virtual Soundcard.
4 Set DVS as your output sound card. Play!
Download free multitracks: www.KLANG.com/multitracks
If you have another Dante enabled product
(e.g. mixing console) proceed with STEP 4.
If not, follow the instructions below to
enable your computer to stream audio via Dante.
audio signals
CONTROLLER
1 OPEN www.KLANG.com/dante
2 Install & Start Dante Controller (DC).
3 Turn o WiFi on your computer.
4In DC, go to ROUTING tab and double
click on your sound source. Go to DEVICE
CONFIG tab and choose preferred
sampling rate. Close this window.
5Now, do the same for and use
the same sampling rate.
Note: Dante devices can only be connected if they
run at the same sampling rates! (Default: 48kHz)
ROUTING
In DC, connect audio streams from sound
source (computer playback or mixing
console) to .

I
A
ANNEX
B
ANNEX
C
ANNEX
D
ANNEX
E
ANNEX
3D MIX TO DANTE ADMIN MODE STAGE SETUP
1OPEN KLANG:app.
3The ROUTING Menu is only available in
ADMIN mode and allows to switch between
Dante or Optical inputs.
4 Under CONNECT you can also change user
names and their icons.
5Musician mode provides a reduced interface
for personal mixing e.g. for live shows.
For remote control with smartphones or
tablets you need to set up a Wifi router:
If you want to use a router for Dante audio
over Ethernet as well, make sure that it’s
suitable (Gigabit Ethernet / No green
eciency settings).
ENGINEER TIPS TECHNICAL DATA
Output Card
Mixing Console
Change Dante Routing:
Open Dante Controller and route audio
from the mixing console to KLANG:vier.
Route its 5 stereo output channels (ch. 1-10)
back to the mixing console or Dante stage-
box.
This setup can be useful when you want to listen to 3D
mixes elsewhere than from KLANG:vier’s analog
outputs.
All five 3D mixes and all 24 optical inputs are
available via Dante.
audio to KLANG:vier & return all 3D mixes to console
3D Mixes
3D Mix Ch. 1-8
Ch. 9-16
Ch. 17-24
control data
SUB-D to
XLR
OPTICAL INPUTS
1Plug in optical cables:
2
Ch. 1-8
Ch. 9-16
Ch. 17-24
Color Codes – Boot Sequence:
Red Boot Stage 1
White Boot Stage 2
Orange Boot Stage 3
Purple Ready / Running
Yellow Error
Color Codes – Firmware Update:
Orange Stage 1/4 & Stage 2/4
Yellow Stage 3/4
White Stage 4/4
Blue Done, Switch O Power
Check for Software and KOS Updates and subscribe to our
newsletter to get informed: www.KLANG.com/update
Dante
Optical 1-8
Optical 9-16
FROM:
Ch.9–16
Ch.17–24
Ch.1–8
Optical 17-24
FROM:
3D Mix
Optical
PAGE 2/2
Optical 1
LOCKED
WARNINGS AND PRECAUTIONS
Do not remove covers. Connect only to main sockets outlets with protective earth.
Do not handle power cords with wet hands. Do not expose to water or other types of
liquids or moisture (rain, fog, dew etc.). Operating temperature: 0 °C to 50 °C (32 °F
to 122 °F). Do not expose to heat sources.
COMPLIANCE
KLANG:vier has been tested and found to comply with
the requirements defined in: EN55103-1:2009 EN 55103-2: 2009. EN 55022:2006 /
CISPR 22:1997 CAN/CSA-CEI/IEC CISPR 22:02 FCC 47 CFR, Part 15.
SAFETY
EN 60065, 7th Edition, Rev.: 09/21/2012;
CAN/CSAC22.2 No. 60065:03 (R2012).
RoHS Compliant and Pb-Free.
WEEE – RECYCLING
According to RL2002/96/EG (WEEE – Directive on Waste Electrical and Electronic
Equipment) electronic equipment has to be recycled and does not belong in the
standard waste. If you are unsure how to recycle this product please contact us and
we will recycle the device for you.
3Set clock source to Optical:
IEM Transmitter
IEM Beltpack
As a monitor engineer you can listen to other users’
mixes via the CUE mode: Click & Hold your
OUTPUT:number for 3 seconds until it turns purple and
then click on the user you want to listen to. To deactivate
click and hold for 3 seconds again.
Output Card
Mixing Console
ADAT
OUTPUT:1
Vocalist
2
3sec!
ENGINEER
OUTPUT:5
CUE from: 1 1
In KLANG:app go to CONFIG
and then to ROUTING:
2 For the next steps, work in Admin mode:
Click and hold CONFIG for 3 sec.
AdminTechnicianMusician
3sec!
1 2
Depending on software version Technician
mode might be called Show mode
DIMENSIONS
Weight: 3 kg | 6.6 lbs, Size (W/H/D): 44.5 / 4.5 / 18.5 cm
Front panel (width): 48.5cm | 19 inches
1 Rack unit, Gap between rack bolts (W/H): 46.5 / 3.5 cm.
WARRANTY – REGISTER ONLINE: www.KLANG.com/register
05.02.20
© KLANG:technologies GmbH, Aachen, Germany, 2020. All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means—electronic, mechanical, photocopy, recording, or otherwise—without written permission by KLANG:technologies
GmbH | Wespienstr. 8-10 | 52064 Aachen | Germany. [phone] – [email protected] – www.KLANG.com/fabrik – Free and Open Source Software Declaration: This product contains free and open source software. For licensing information please visit
www.klang.com/license or open KLANG:app connect to your product and go to CONFIG > CONNECT > ABOUT or check the unit‘s HTML server with a web browser by typing http://<UNIT_SERIALNUMBER>.local or http://<UNIT_IP_ADDRESS>.