Klip Xtreme KPM-321 User manual

Introduction:
1. Hardware kit
Thank you for purchasing the KPM-321 LCD/LED triple monitor mount. This product is
shipped with all proper installation hardware and components. Upon opening the box, make
sure that none of these parts are missing and/or damaged before beginning installation.
LCD/LED triple monitor mount
KPM-321
Label
A
B
C
D
E
F
G
H
I
Item
Desktop base
Shaft
Mounting arm
VESA center plate
Cable clip
Cable clip with tool holder
Decorative shaft cap
3mm allen wrench
5mm allen wrench
Quantity
1
1
1
1
6
1
1
1
1
Image
Articulated
joints Heavy-duty desktop base

3. Product diagram
(per arm)
Max load
17.6lb
8kg
Label
J
M-A
M-B
M-C
Item
6mm allen wrench
M4x12mm screw
M5x12mm screw
D5 metal flat washer
Quantity
1
12
12
12
Image
IMPORTANT:
At least two qualified people should perform the assembly procedure. Personal injury and/or
property damage can result from dropping or mishandling the display.
Mounting surfaces must be sturdy and flat.
Do not install this product on a weak, uneven surface, prone to vibration or susceptible to
other movements. Reinforce the structure as necessary before installing the mount.
Maximum weight supported:
The combined weight of all components shall not exceed the rated load capacity of the
mounting arm.
2. WARNING!
• Prior to installing this product, you must read all instructions thoroughly. Keep these
installation instructions in an easily accessible location for future reference.
• Safety measures must be practiced at all times during the assembly of this product. Use
proper safety equipment and tools for the assembly procedure to prevent personal injury.
• KlipXtreme does not warrant against damage caused by the use of any KlipXtreme mounts
for purposes other than those for which it was designed or damage caused by unauthorized
attachments or modifications, and is not responsible for any damages, claims, demands, suits,
actions or causes of action of whatever kind resulting from, arising out of or in any manner
relating to any such use, attachments or modifications. 4. Desktop base installation
Note:
• Prior to installing the product, choose your preferred location to mount the monitors. Make
sure that the surface is sturdy and flat. Do not install this product on a weak or uneven desk
or countertop.
• Padded edges beneath the base provide surface protection, a stable grip, and will also
prevent the mount from sliding out of place.
1. First, insert the tool holder and the decorative cap onto the shaft.
2. Then screw the shaft into the mounting socket of the base and tighten the bolts with the
allen wrench to secure it.
466mm
81.5mm
113mm 100mm 75mm
116mm
100mm
25mm
200mm
200mm
200mm
35mm
434mm
316mm
180˚
340˚
340˚
± 90˚
360˚ ± 45˚
48mm
35mm

.
5. Attaching the mounting arm assembly
1. Once you have completed the installation steps described above, slide the mounting arm
assembly onto the shaft and tighten the clamp bolts at the desired height. Make sure to
exert enough pressure to hold the support steady and in place.
2. Then insert the center VESA plate onto the shaft and secure it by fastening the clamp bolts
with the supplied allen wrench.

.
5. Attaching the mounting arm assembly
1. Once you have completed the installation steps described above, slide the mounting arm
assembly onto the shaft and tighten the clamp bolts at the desired height. Make sure to
exert enough pressure to hold the support steady and in place.
2. Then insert the center VESA plate onto the shaft and secure it by fastening the clamp bolts
with the supplied allen wrench.
3. Attach all six cable clips on the arms.
6. Attaching the monitor to the VESA plate
1.Carefully place your display face down on a soft, even surface, and identify the threaded
mounting points that are located on the back panel.
2.Determine the correct screw size by carefully inserting a straw or toothpick, and mark the
depth of the mounting point. Please note that not all the hardware included will be used.
CAUTION: Verify the adequate thread engagement of the screw/washer combination on
your monitor. Too short will not hold the display and too long will damage it.
Attention: Two people might be needed to complete the steps below.
3. For 100x100 VESA monitors, loosely thread (leaving a 3mm clearance) the two top screws
into the holes on the back.
4. Then hang the monitor onto the top grooves of the VESA plate, and finish by inserting the
other two screws in the lower holes from behind the display. Refer to the image below.
Too short Correct Too long
Monitor installation

5. 75x75 VESA monitors must be attached directly from behind the mount. Hold the display
with both hands to align the threaded inserts on the back panel with the ones on the plate.
6. Finish by fastening the screws with a phillips-head screwdriver, but be careful not to
over-tighten them.
7. Repeat the same procedure for the other to monitors and guide cords through the clips.
7. Final adjustment
1. Position both ends of the arm in a straight line first, as shown below. Arms can be then bent
and adjusted at an angle as long as monitors are held within its center of gravity.
2. Now you can adjust the vertical (tilt) and horizontal (swivel) action of the mount.
3. Fully tighten the screws of the joints when the optimal viewing angle is reached. The
monitors can be also rotated for portrait or landscape orientation, or anything in between.
4 .Finally, place the wrenches in the tool holder when not in use.

.
NotesNotes