Knight Stoves ILD 6 User manual

1
ILD 6 Insert: EN13229 - NS3058 - AEA
Manual version No. 12-1a GB 22-11-2012
Model 6 insert

2
CONTENT
First use............................................................................................................................................... 3
Technical data sheet ........................................................................................................................... 4
Before installation............................................................................................................................... 5
Packing................................................................................................................................................ 5
Installation.......................................................................................................................................... 6
Ventilation example: ......................................................................................................................... 11
Distance to combustible wall protected by brick or Jøtul Firewall................................................... 12
Closed combustion system................................................................................................................ 13
Chimney & flue collar:....................................................................................................................... 14
The chimney effect:........................................................................................................................... 15
Measurements................................................................................................................................... 17
Setup Examples................................................................................................................................. 18
Refuelling on to a low fire bed.......................................................................................................... 19
Fuel overloading................................................................................................................................ 19
Environmental use ............................................................................................................................ 19
Smoke Control Areas: ....................................................................................................................... 20
Primary air control: ........................................................................................................................... 21
Secondary air control:....................................................................................................................... 22
Ash drawer and bottom grate:.......................................................................................................... 23
Dampers left open............................................................................................................................. 23
Fuel.................................................................................................................................................... 24
Lightning the stove: .......................................................................................................................... 25
Cleaning maintenance....................................................................................................................... 27
Trouble shooting: .............................................................................................................................. 28

3
Thank you for having confidence in us
Ild is a range of safe, environmentally friendly and efficient high-quality stoves, which meet
all requirements for a modern heating source. In order to get the best out of your stove, we
recommend that you read this booklet and our homepage www.ildstoves.com carefully.
First use
Before the stove is heated up for the first time, we advise you to open all windows and doors
in the room to ensure optimum ventilation. When the stove is at operating temperature, the
surface treatment will harden and emit a strong odour for a short time. As a result of the
heating and due to the ensuing change in temperature, the stove will produce sounds which
may be loud and varied.

4
Technical data sheet
Model 6 Wood Units
CO-Emission at 13% O2 : 0,08 %
NOx @ 13% O2 133 mg/Nm3
Efficiency 83 %
Nominal performance 4,5 Kw.
Chimney temperature EN13229 192 Co
Recommended underpressure in flue connection piece 16 Pa.
Flue pipe underpressure EN 13229 12 Pa.
Combustion air requirements 13 m3/h
Fuelconsumption 1,3 Kg/h
Stokingquantity 1,0 Kg.
Weight 54 Kg.
Flue connectionpiece Øi 126 mm.
Flue connectionpiece Øu 130 mm.
Max. Fuelsize diameter 100 Cm.
Max. Fuel length 20 Cm.
Power band 0-6 Kw.
Type of verification EN 13229-DEFRA-NS3058

5
Before installation
Ensure that your Local Chimney sweeper can recommend wood stove installation
Ensure that updated European, national and local standards can be fulfilled
Ensure that the area can support the stove and installation weight
Ensure that there will be sufficient space and access to service
Ensure that the Chimney has a minimum draft of 12 Pa.
Ensure that the rated power of stove are suitable for the room
Ensure that combustible material are at least 800 mm. from rear part of the stove.
Warning ! It is not allowed to make any unauthorized changes to the stove
Packing
The stove comes packaged in the karton box on wooden pallet nailed down on vertical boards
at the corners. In karton box stove is fixed with EPS styrofoam elements.
Consult local regulations on the disposal of these materials; the wood has been treated to
repel vermin and may not be burnt in stove.

6
Installation
Prepare a non combustible base with spare space (+) for the convection box which is: W 390
(+) H 550 (+) Depth 350 (+)
Heart must be minimum 350 mm. Higher than floor and 150 mm wider at both sides than
outer frame in front it must reach out 450 mm from frame .
After unpacking of the stove first thing which needs to be done is removing buffle plate from
firebox. In order to remove buffle plate you need to remove two pins (Picture 1) and after
that draw buffle plate out from the firebox (Picture 2).
Picture 1 Picture 2
After removing of buffle plate you need to unscrew 4 bolts which hold connectiong piece for
close combustion (Picture 3).
Picture 3

7
The stove should be removed from the box before instalation. Removing the stoves from the
box will be done in few steps.
In order to remove stove from the box you need to unscrew the bolt which is attached to the
box (Picture 4). Furthermore two outside bolts on the bottom part of stoves needs to be
removed also (Picture 5).
Picture 4 Picture 5
Next step of remving stove from the box is to lift stove a little and than drag stove toward
yourself (Picture 6).
In order to continue instalation of the stove you need to unscrew 4 bolts on the box which holds
flange of connecting piece (Picture 7).
Picture 6 Picture 7

8
After remowing of 4 bolts you need to take off flange together with connectiing piece (Picture 8).
Flexible smoke pipe will be installed on connecting piece with two bolts as it is showed on
Picture 9.
Picture 8 Picture 9
The next step of instalation is to install box in prepared hole. Furthermore after installing box into
the hole you need to pull through upper hole on the box connecting piece with installed smoke
pipe (Picture 10).
Picture 10

9
Outer flange you need to position and consolidate with 4 nuts (Picture 11). After instalation of
smoke connector you need to level box by 4 screws as it is presented on the Picture 12.
Picture 11 Picture 12
There are provided 4 holes on the box for fixing on the down part (Picture 13) and also 4 holes
on the sides. Box of the stove needs to be fixed by turbo bolts in the bottom or on the sides
(Picture 14).
Picture 13 Picture 14

10
After fixing of the box you need to put stove back in the box (Picture 15). Then put back the two
screws (Picture 16).
Picture 15 Picture 16
Also you need to twist and thinghten screw on the upper part of the stove in order to
completely fix stove and box (Picture 17). At the end of instalation you need to place back
buffer plate and pins (Picture 18).
Picture 17 Picture 18