Koala JoEY KOOKABURRA Manual
KOOKABURRA COT INSTRUCTION GUIDE
RED NOSE RECOMMENDATIONS
Red Nose Recommendations for babies
aged 0-12 months to help reduce the risk of
sudden infant death:
1. Always place baby on their back to sleep.
2. Keep baby’s face and head uncovered.
3. Keep baby smoke free, before and after birth.
4. Use a safe sleeping environment, night and day.
5.
Sleep baby in safe cot in parents’ room for the first 6-12 months.
6. Breastfeed baby.
7. Baby should always be placed on their back to sleep,
with their feet at the bottom on the cot.
Do not place more than one mattress in a cot.
CARE RECOMMENDATIONS
1. Spot clean surface using a damp cloth.
2. Do not use harsh or abrasive cleaners as this may damage
the surface of the product.
3.
Don’t place cot in direct sunlight as this may cause materials
to fade or crack. Direct sunlight includes sunlight through
a window.
Configuration
B. Low Configuration
A. High Configuration
After reading the warnings, the red nose recommendations,
and the care recommendations, scan the QR code to watch a
video which demonstrates how to assemble the cot.
What’s in the box
End Panel x2 Retainer x4 Safety Bolt x4
Side Panel x2 Base Platform x1 Middle Spacer x2
Corner Spacer x4
Introducing the Koala safety bolt
Ensure that cap is pressed up when rotating.
Lay out the side and end panels on the floor with hooks facing upwards.
Step 1: Align end panel hooks with the side panel slots. Push the side panel
down to make sure they are locked in.
Repeat steps for the other side.
Ensure bracket
holes align
Step 2: Assemble the end panel into position and secure with hooks.
Note: The following steps are for the high configuration, for low
configuration go to step 3B.
Step 3A: Place the middle spacers into the centre pins and ensure they
are upright.
A. High Configuration
Step 4A: For the baby configuration, fasten the threaded spacers to the
retainer through the base panel. Repeat on all corners.
A. High Configuration
Step 5A: Lower the bed base with attached spacers onto the support brackets.
Align the bottom hole of the spacers with the holes on the metal brackets.
Ensure
the middle
spacers are
aligned
A. High Configuration
Step 6A: Fasten the bed base down by screwing the safety bolts into the bottom
of the corner spacers through the metal brackets.
Note: All assembly fittings should always be tightened properly and fittings
should be checked regularly and re-tightened as necessary.
A. High Configuration
Note: This configuration
does not need corner spacers
and middle spacers and they
should be stored properly.
B. Low Configuration
Step 3B: Lower the bed base onto the support brackets. Align the corner
holes of the bed base with the holes on the metal brackets.
B. Low Configuration
Step 4B: Place retainers on all four corners.
Note: This configuration
does not need corner spacers
and middle spacers and they
should be stored properly.
B. Low Configuration
Step 5B: Fasten the bed base down by screwing the safety bolts into the
retainers through the metal brackets.
Note: All assembly fittings should
always be tightened properly and
fittings should be checked regularly
and re-tightened as necessary.
B. Low Configuration
Manufactured for Koala Sleep Pty Ltd
Website: koala.com
Phone: 1800 575 337
Address: Unit 12 37-41 O’Riordan Street, Alexandria,
NSW 2015, Australia
Date of launch - 03/2023
SKU-105-0007
This COT is intended for babies aged 3 months to when they are
observed attempting to climb out of the cot and looking like they
might succeed. This usually occurs when the baby is between 2
and 3 ½ years of age but could be as early as 18 months.
REV1.1
Table of contents
Popular Baby & Toddler Furniture manuals by other brands
pottery barn kids
pottery barn kids SHELTER TODDLER BED manual
Kids II
Kids II Disney Baby 60578-ES manual
Bright Starts
Bright Starts Disney Baby 60256-ES manual
Escape
Escape Babymoov NAOS Instructions for use
DOM FAMILY
DOM FAMILY Karley owner's manual
Babystart
Babystart Delfina 377/4467 Assembly instructions