Kocchis Forklift Cam 723H2561-MP5V User manual
①Left(Vol-) ②Right(Vol+) ③Menu/Esc ④Down(CH switch) ⑤Up(CH switch)
⑥OK ⑦Power ⑨Digital wireless camera
①②③④⑤⑥⑦
MENU
⑧
⑨
Cable Interface Definition
Monitor Camera
Red Power
Black Ground
Red Power
Black Ground
Brown TIRG1
Blue TIRG2
MENU
DC8-32V
DC12V
＞1M
＜1M
Installation Notes:
Camera and truck arm distance is greater
than 1M
.
23445678ÿ:;45<3=3>?ÿ@2ÿA:B
Digital Wireless Forklift Camera System
User Manual
Display Device Color TFT-LCD
Size 7" Digital Screen
Operation Frequency 2400 ~ 2483.5MHz
Receiving Sensitivity ≤-86dBm(1MHZ QPSK MD300RE)
Resolution 800×(RGB)×480
View Angle (LR/UD) L/R: 70/70 U/D: 50/70
Contrast Ratio 500:1
2
Luminance(cd/m ) 450
Response Time (ms) 25
Load Dump DC 12+87V/400ms
Operating Temperature -20℃～+60℃
Storage Temperature -30℃～+80℃
DC8V～32V （ 5W Max）
Dimension(L x W x T) (185X122X28mm)
Transmission Power 18dBm with Power control
Camera Wireless waterproof and shockproof digital camera
Image Pick-up Device 1/3" Color CMOS
Picture Elements NTSC:960(H)X480(V);PAL:960(H)X480(V)
Horizontal Resolution 600 TV Lines
Minimum Illumination 1 Lux
View Angle 45°
Waterproof Rating IP67
Shockproof R ating 10G
Operating Voltage Range DC12V
Dimension 127(W) x 37(H) x 24.5(D) mm
Digital wireless system technical parameters Monitor Menu Operation
2) Picture setting：
Enter the menu, chose the picture and press OK,
1.Brightness: 0-10 (Press left/right to adjust)
2.Contrast: 0-10 (Press left/right to adjust)
3.Color: 0-10 (Press left/right to adjust)
Auto scan setting Function set
F
F
F
F
3) Mirror/Normal image setting:
Set the CAM1 and CAM2 image in 4 modes.
PAIRING SART
50
5
-
+
5
-
+
5
-
+
5
-
+
4) Auto Scan setting:
1. Set CAM1 auto scan mode on/off;
2. Set CAM2 auto scan mode on/off;
3. Set the auto scan time.
5) Other function:
1. NTSC or PAL system switch;
2. LED screen ambient light sensor on/off.
3. Electronic Label setting: Turn on/off the electronic
label on CAM1.
ON OFF
ON OFF
Nor/Mir
PAIR PICTURE
1) Pair: Establish the connection between the monitor
and camera, make the system work in order.
Enter the menu, chose PAIR and press OK to enter
the pair. the monitor display PAIRING START 50. During
the 50 seconds, make the camera re-energized, the
monitor will show the camera image in 5~10s.
Note:
When the monitor in SCAN mode, the CAM1 and CAM2 image will switch automatically
according the setting time. Press ▼/▲ to quit the switch.
The system maintenance must be maintained by professionals, please do not open and
improve the system!
The system is only for the safe operation of equipment and not responsible for accidents!
This manual is for reference only. if unknown, or any changes, we will give no notice.
The final interpretation right belongs to the manufacturer
Warning
Input Voltage Range
