Koden KDS-1100 User manual

KSD-1100/1210 Revision History
0093107083-01 i
KSD-1100/1210 Operation Manual
Doc No: 0093107083
Document Revision History
No. Doc. No.- Rev. No. Date Revised
(Y/M/D)
Revised Content
0 0093107083-00 2022/04/12 First edition
1 0093107083-01 2022/08/10 Declaration (KSD-1100)
2
3
4
5
6
7
8
9
10
Document No. Revised Version Norm
When part of the document needs to be revised, the document has advanced revision
number.
The document No. is indicated at the lower right side on the cover and at the left or right side
of the footer region of each page.
© 2022 Koden Electronics Co., Ltd. All rights reserved.
No part of this publication may be reproduced, transmitted, translated in any from by any
means without the written permission of Koden Electronics Co., Ltd. The technical
descriptions contained in this publication are subject to change without notice. Koden
assumes no responsibility for any errors, incidentals or consequential damages caused by
misinterpretation of the descriptions contained in this publication.
NOTE: Please scan the QR codes to visit our website for the Advanced operation manual.
https://www.koden-electronics.co.jp/enopmn
NOTE: KSD-1210 is not complied for CE Approval.

Important Notice KSD-1100/1210
0093107083-01
ii
Important Notice
•For copy and transcription of this Operation Manual (hereinafter referred to as this
manual), permission from Koden is needed. Koden prohibits the un-authorized copy and
transcription of this manual.
•If this manual is lost or damaged, consult a dealer of Koden or Koden.
•The specification of the products and the contents in this manual are subject to change
without notice.
•The contents displayed on the menu of product may be different from the expression of
this manual. The fonts and shapes of the keys and menus in the illustration may differ
from the actual ones, and some parts may be omitted.
•Koden is not liable for damages and troubles arisen from misunderstanding of the
contents in this manual.
•Koden is not liable for any damages caused by earthquake, lightning, wind and flood
damage and fire for which Koden is not responsible, and actions by third parties, other
accidents, customer’s unintended error/abuse and the use under other abnormal
conditions.
•Koden is not liable for damages of accompaniment (change/loss of memorized content,
loss of business profit, stop of business) arisen from use or failure of our products.
•If the stored data are changed or lost, irrespective of causes of troubles and damages,
Koden is not liable for them.
•Koden is not liable for any damages arisen from malfunction caused by combination of
software and connected equipment in which Koden is not engaged.

KSD-1100/1210 For Your Safe Operation
0093107083-01 iii
For Your Safe Operation
Pictorial used in this Operation Manual
This Operation Manual uses the following pictorials. Understand the meaning of each pictorial
and implement the maintenance and inspection.
Symbol
Meaning
Mark for warning
This symbol denotes that there is a risk of death or serious injury
when not dealing with it correctly.
Mark for danger high voltage
This symbol denotes that there is a risk of death or serious injury
caused by electric shock when not dealing with it correctly.
Mark for caution
This symbol denotes that there is a risk of slight injury or damage of
device when not dealing with it correctly.
Mark for prohibition
This symbol denotes prohibition of the specified conduct. Description
of the prohibition is displayed near the mark.
Caution Item on Equipment
Be careful of a high voltage inside.
A high voltage, which may risk your life, is used. This high voltage
remains in the circuit after you have powered off switch. To prevent
touching the high voltage circuit inadvertently, the hard cover is
provided to the high voltage circuit and the high voltage caution label
is affixed. Ensure to power off switch for your safety and discharge
the electricity remaining in the capacity before starting to check. An
engineer authorized by our company should inspect and maintain
Be sure to power off in the boat.
If the power switch is inadvertently powered on during work, you will
be electrified. To prevent such accident from occurring, ensure to
power off in the boat and the power of equipment. Furthermore, it is
safer to hang the caution tag described as [Under Work] near the
power switch of equipment.
Be careful of dust
Inhaling dust may causeA respiratory disease. When cleaning the
inside of equipment, be careful not to inhale dust. Wearing a safety
mask is recommended.

For Your Safe Operation KSD-1100/1210
0093107083-01
iv
Caution on location of equipment
Do not install the equipment where it is excessively damp and suffers
from excessive water drops.
Escaping from static electricity
The static electricity may be generated from the carpet on the floor in
the cabin or clothes made of synthetic fiber. The static electricity may
destroy the electronic parts on the circuit board. Handle the circuit
board, taking the measure of static electricity free.
Firmly installation of this unit is necessary to avoid damage caused
by falling down.
Power supply should be grounded to avoid static and lightning. If this
unit is not in use, please turn off this unit.
Caution Item on Handling
Do not disassemble or modify. It may leads to trouble, fire, smoking
or electric shock. In case of trouble, contact our dealer or our
company.
In case of smoke or fire, boat power off and the power of this unit. It
may cause fire, electric shock or damage.
Be cautious of remaining high voltage.
A high voltage may remain in the capacitor for several minutes after
you have powered off. Before inspecting inside, wait at least 5
minutes after powering off or discharge the remaining electricity in an
appropriate manner. Then, start the work.
The information displayed in this unit is not provided directly for your
navigation. For your navigation, be sure to see the specified material.
Use the specified fuse. If un-specified fuse is used, it may cause a
fire, smoke or damage.
Please do not use this unit without original power adapters.
Otherwise, the navigator may not work properly or the performance
might be affected or even this unit will be damaged because of the
circuit designs.

KSD-1100/1210 For Your Safe Operation
0093107083-01 v
If the position data of the device cannot be fixed for a long time,
please check the following: whether the antenna is installed properly;
the connection; any forms of interference around the antenna. Before
starting of this unit, please make sure the antenna cable joints are
intact; there is no short-circuit or open circuit; and follow the correct
antenna installation procedure. During the start-up stage, please do
not arbitrarily remove the antenna in order to avoid damages to this
unit.
When external temperature is too high, this unit may not function
properly. Stop using this unit until the temperature returns to normal
and restart this unit.
Avoid direct sunlight on the LCD screen. You can adjust the angle of
the screen anytime to get the best visual effects.
When hardware failure occurs (for example, power lines are burned,
machine is damaged or foreign bodies fall into this unit, etc.), please
shut down the power and contact with the distributor immediately.
Virtually, all data sources might contain some inaccurate or
incomplete data. The data is only for your reference and we cannot
guarantee any accident, injury or property damage. All legal
responsibility and other obligation will not be taken by Koden.

Contents KSD-1100/1210
0093107083-01
vi
Contents
Document Revision History....................................................................................... i
Important Notice....................................................................................................... ii
For Your Safe Operation...........................................................................................iii
Pictorial used in this Operation Manual........................................................iii
Caution Item on Equipment .........................................................................iii
Caution Item on Handling ........................................................................... iv
Contents...................................................................................................................vi
Introduction............................................................................................................viii
System Configuration...............................................................................................ix
Configuration of Equipment......................................................................................xi
Chapter 1 Basic Operation....................................................................................1-1
1.1 Network Connection ...................................................................................1-1
1.2 User Register/Login....................................................................................1-1
1.2.1 Register...........................................................................................1-1
1.2.2 Login................................................................................................1-1
1.2.3 Forget Password..............................................................................1-1
1.3 Dual Chart System......................................................................................1-1
1.3.1 Instruction of S-57 Chart Installation................................................1-1
1.3.2 Display setting .................................................................................1-2
1.4 Track Operation..........................................................................................1-5
1.4.1 Track Record ...................................................................................1-5
1.4.2 Track Color Switch...........................................................................1-6
1.4.3 Track Deletion..................................................................................1-6
1.4.4 Track Batch Edit, Deletion................................................................1-6
1.5 Navigation Data Operation..........................................................................1-7
1.5.1 Navigation Data Creation.................................................................1-7
1.5.2 Navigation Data Deletion .................................................................1-7
1.5.3 Navigation Data Batch Edit, Deletion...............................................1-7
1.6 Navigation operation...................................................................................1-8
1.6.1 Call Navigation Data / MOB to navigation........................................1-8
1.6.2 Call History Navigation Data............................................................1-8
1.7 Plot Data Operation....................................................................................1-8
1.7.1 Plot Data Creation............................................................................1-8
1.7.2 Plot Data Deletion............................................................................1-9
1.7.3 Plot Data Batch Edit, Deletion..........................................................1-9
1.8 AIS Operation.............................................................................................1-9
1.8.1 AIS List ............................................................................................1-9