Kohler Toobi 8963T-B9 User manual

1338604-2A-A 1
INSTALLATION INSTRUCTIONS
8962T-B9 Wall-Mount Shower Faucet
8963T-B9 Wall-Mount Bath & Shower Faucet
TOOBI
BEFORE YOU BEGIN
HANDLE OPERATION
For 8962T-B9, push the handle back, turn clockwise for cold water, counter-clockwise for hot water.
For 8963T-B9, push the handle down, turn clockwise for cold water, counter-clockwise for hot water, bath spout
works; lift the diverter gently, turn clockwise for shower; shut off the faucet, turn counter-clockwise until it stops.
ROUGH-IN DIMENSIONS
Special model meets or exceeds the following at date of manufacture: TIS
STANDARD APPLICABLE
All information is based on the latest product information available at the time of publication. Kohler Co. reserves
the right to make changes in product characteristics, packaging, or availability at any time without notice.
Please leave these instructions for the consumer. They contain important information.
NOTES:
1.Flush the water supply pipes thoroughly to remove debris.
2.The minimum inlet water pressure for the diverter is 0.05MPa(0.5bar).
3. The highest working pressure for handshower & showerhead is 0.5MPa(5bar). If it exceeds 0.5MPa(5bar),
a pressure reducer is needed. The highest water and environment temperature is 60ºC. Please keep handshower,
showerhead and shower arm away from heater, or it may become damaged and cause injury to the user.
1338604-2A-A 4
TOOBI
SERVICE PARTS
**Color code must be specified when ordering.
NOTE: For all Asia pacific regions (excluding China) add SP (SPxxxxxxx**) in front of the part number when ordering.
8962T-B9 Wall-Mount Shower Faucet
8963T-B9 Wall-Mount Bath & Shower Faucet
831727**
880010
1297467**
1030624
1240266
77420
864922**
1218659
870721
1170944**
3011113
834705**
3010690**
3010689**
864471
870992
3010698
3010697**
833438
834705**
3012713**
834460
880085
880084
3010213
834791**
1146844-A**
Green:3010756
White:3013331
1152362-A**
3010970**
3010715 1086390
1059041**
Green:3010692
White:3013329
8963T-B9
Ø61
G1/2˝
153~160
223
G1/2˝
64º
283
150±15
Handshower
Hose
Bracket
50
40
22.5
40º
Ø61
G1/2˝
84~91
G1/2˝
150±15
293
8962T-B9
G1/2˝
G1/2˝
1500
Ø28
240
G1/2˝
250

1338604-2A-A 2 1338604-2A-A 3
INSTALLATION
How to Install the Faucet
To perform installation, installer must provide G1/2˝ female supply
fittings(1), spaced 150mm apart and horizontal. The supply fittings should
be vertical and not beyond the finished wall. Hot supply pipe must be
located on the left.
Install the two offset connectors(2) into the hot and cold supply pipes.
Use appropriate thread sealants or thread tape on pipe threads.
Adjust the center-to-center distance between the connectors to 150mm
and horizontal. They should extend 36 to 47mm beyond the finished wall.
Slide the escutcheons(3) onto the nuts(4). Put the washers(5) into the
nuts, thread the nuts to connectors. Tighten the nuts with strap wrench or
soft cloth between product and regular wrench. Push the escutcheon
against the finished wall.
Install the restrictor(10) into the handshower(9) inlet if needed.Connect
hose(6) to the faucet outlet(8), and to the handshower with washers(7).
INSTALLATION CHECKOUT
CLEANING INSTRUCTIONS
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean soft
cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc. which could adversely
affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets and fittings.
How to Install the Bracket
Determine a suitable location on the finished wall to install the bracket.
Mark bracket base mounting hole locations on the wall according to the
dimension. Drill two holes on the finished wall, the holes should match
the anchors(11). Install the anchors. Tighten screws(12) to secure
bracket base(13) to the finished wall. Put the bracket(14) onto the bracket
base and lock by stopper. Hang the handshower on the shower bracket.
How to Operate the Handshower
Press the buttons of the handshower to change the water flow.
How to Maintain the Handshower
Any debris or mineral build-up may cause the flow stream to become
distorted or reduce the flow rate. To remove the debris or mineral build-up,
run water through the handshower, firmly press or rub your finger back
and forth across the rubber nozzles.
Remove and clean the screen washer.
Katalyst Air
Intense Massage
2
1
Hot
Cold
150mm
36-47mm
Hot
Cold
3
4
5
6
7
8
9
10
22.5mm
11
12
14
13
9
15
9
16
Ensure that all connections are tight. Ensure that the handle is in the off
position.
Turn on the drain and main water supply, and check for leaks. Repair as
needed.
For 8963T-B9
Bath & Shower Faucet
Remove the handshower(9). Press the bulge(15) of the aerator(16) on
the underside of the spout, Remove the aerator. Turn on the faucet. Run
the water through the spout about one minute to remove any debris.
Check for leaks. Remove any debris from the aerator. Shut off the faucet.
Reinstall the handshower and aerator.
For 8962T-B9
Shower Faucet
Remove the handshower(9). Turn on the faucet. Run the water through
the spout about one minute to remove any debris. Check for leaks. Shut
off the faucet. Reinstall the handshower.