Kohler ELATE 13963T-B4 User manual

1230981-2A-C 1
BEFORE YOU BEGIN
All information is based on the latest product information available at the time of publication. Kohler Co. reserves
the right to make changes in product characteristics, packaging, or availability at any time without notice.
Please leave these instructions for the consumer. They contain important information.
NOTES:
1. Flush the water supply pipes thoroughly to remove debris.
2. For new installations, assemble the faucet to sink before installing.
3. The highest working pressure for handspray & shower head is 0.5MPa(5bar). If it exceeds 0.5MPa(5bar),
a pressure reducer is needed. The highest water and environment temperature is 60ºC. Please keep handspray,
shower head and the shower arm away from heater, or it may become damaged and cause injury to the user.
HANDLE OPERATION
Lift the handle gently. Turn clockwise for cold water, turn counter-clockwise for hot water.
1230981-2A-C 4
INSTALLATION INSTRUCTIONS
13963T-B4 Pull Out Kitchen Faucet13963T-B4 Pull Out Kitchen Faucet
ELATEELATE
ROUGH-IN DIMENSIONS
SERVICE PARTS
**Color code must be specified when ordering
2.5º
G1/2˝
82
182
1700
800
228
Ø36~Ø42
258
Max.80
304
616
1106464
1036389
880096
1229188**
1153137**
1153263
1102621
1106466
1106107
1128042
1104495
29296
1229484
70012
1105827**
1106461
38676
1232536
1106462**
38676
1132368**
56283
1243690**
1111585
1046153
101131
1103431

1230981-2A-C 2 1230981-2A-C 3
INSTALLATION CHECKOUT
CLEANING INSTRUCTIONS
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean soft
cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc, which could adversely
affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets and fittings.
INSTALLATION
How To Install The Faucet
If the escutcheon kit(1) isn’t slided into the groove on the bottom of the
body(2), then you need to slide it into the groove on the bottom of the
body. Insert the hoses and mounting studs(3) into the mounting hole of
the sink. Let the bottom of the body against the deck.
From underside of the sink, fit the mounting bracket(4) on the mounting
studs. Position the faucet so that the spray hose(5) is on the left, the
spray hose and two hoses(6) are symmetrical. Tighten two nuts(8) with
wrench(7) to the mounting studs so that they can secure faucet to sink.
Attach the hoses to water supplies. When facing the faucet, the hose in
front connects to hot water, the back hose with ‘COLD’ label connects to
cold water.
Put the weight(10) and clip(11) onto the hose(5). Adjust the weight so
that the distance is right from the bottom of the faucet to the weight.
Insert the hose(5) into the connector(9).
Ensure that all coupling nuts are tight. Ensure that the lever handle is in
the off position. Turn on the main water supply and drain, and check for
leaks. Repair as needed.
Remove the spray(12). Run hot and cold water about one minute to
remove any debris. Remove any debris from the filter washer and aerator
of the spray. Shut off the faucet. Reinstall the spray.
How To Use Spray
Open the handle, if you want to use the spray by hand, take the spray
and pull out the hose.
Press the button(A) as shown for the water close. Press the button(B),
(C) as shown for two different forms of water flow, as figure(a), (b) shown.
NOTE: Please pull it gently and do not draw out the spray hose too long,
or you may damage the hose and connector.
A
BC
ab
12
6
3
2
1
4
7
8
5
10
11
9
"LEAD FREE" is marked on the back of the faucet signifying its compliance with the United States AB1953