Kohler K-2200-G User manual

-1-
BEFORE YOU BEGIN
NOTES
·
·
·
·
·
Use these instructions for above-counter installation.
Please follow the instructions that apply to your
installation.
You can choose between a wall-mount or
countertop faucet installation, depending upon the
setting and styling you desire. We recommended a
wall-mount .
Prior to installation, unpack the new lavatory and
carefully inspect it for damage. Return the lavatory
to its protective carton until you are ready to install it.
All information in these instructions is based upon
the latest product information available at the time of
publication. Kohler Co. reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
These instructions contain important care, cleaning,
and warranty information. Please leave these
instructions for the consumer.
faucet
ROUGHING-IN DIMENSIONS
Fig. #1
(S)
(T)
3/8" HOT
102mm 102mm
3/8" COLD
1-1/4" OUTLET
**76mm
162mm
254mm
413mm
OF FITTING*
C
L
K-2200-G
1007250-K01-A
INSTALLATION
INSTRUCTIONS
VITREOUS CHINA
ABOVE-THE-COUNTER LAVATORY
K-2200-G
COPYRIGHT 2002 KOHLER Co.
C
Roughing-In Notes
Fixture dimensions are nominal and conform to
tolerances in ASME Standard A112.19.2M.
(T) Pop-up drain 229mm.
(S) 356mm (Based on 305mm riser which may
require cutting).
* Spout must be 127mm long (min.) for adequate
clearance into lavatory when installed with centerline
as shown.
** Spout must be tall enough to clear 76mm rim
height and provide a 25mm air gap per ASME
A112.1.2.

TOOLS AND MATERIALS REQUIRED
(Not supplied)
·
·
·
·
·
·
·
·
·
·
Sealant
Template (supplied)
Safety glasses
Pencil
Scissors
Tape Measure
Hole Saw
Keyhole saw or saber saw
Drill (1/2" dia. Drill bit, or larger)
Screwdriver
-2-
Position the template on the countertop.
Be sure to provide sufficient
spout overhang into the lavatory. See the roughing-in
notes for minimum spout length information.
Pay special attention to the
spout and handle fit clearance when locating the
faucets, as noted below. Use the template to locate the
faucet spout hole centerline on the countertop. This
centerline is recommended to provide adequate
clearance between the edge of the lavatory and the
spout.
Check for adequate clearance between the backsplash
or wall faucet spout and handles, and lavatory. We
recommend clearance of at least 25mm between:
The installed lavatory and the faucet spout,
The installed lavatory and the end of the faucet
handles, and,
The faucet spout and handles and the backsplash or
wall.
Refer to the faucets installation instructions for required
clearance, and mark the preferred faucet hole locations
using a soft lead pencil.
Trace the template on the countertop using a soft lead
pencil.
For Wall-mount Faucets:
For Countertop :Faucets
·
·
·
COUNTERTOP INSTALLATIONS
Fig. #2
25mm Min.
Clearance
Spout
Centerline
Backsplash
Cut-out line
Outside Edge
of Lavatory
Cut out the opening by carefully following the pencil line.
Large lavatories are very heavy. Get
help lifting the lavatory into place.
Temporarily position the lavatory in the countertop
cutout so the "Kohler" logo is visible. The logo is
located inside the lavatory, near the rim, and should be
positioned near the faucet.
Verify proper clearance between the lavatory, faucet,
and backsplash.
Remove the lavatory from the countertop cutout, and
return it to its protective carton. Do not stand or store
the lavatory on the drain surface.
CAUTION: Risk of personal injury or product
damage.
Fig.#3
1007250-K01-A

For tile, wood, or other porous materials, apply
waterproof sealant around the cutout area of the
countertop surface. Follow all manufacturer's
instructions and warnings. Allow the sealant to dry
before proceeding.
Use a 50/50 mixture of isopropyl alcohol and water to
clean the countertop surface around the cutout area.
Wipe dry with a clean cloth.
: Install the adhesive sealant when the
temperature is at least 10 . The preferred temperature
range to apply the adhesive sealant is 21 to 38 .
Loosely apply the adhesive sealant around the entire
countertop cutout so it is alongside the cutout hole.
Adjust the placement of the sealant before removing
the backing material. Cut off any excess seal material.
Carefully remove the adhesive seal backing material.
NOTE
Fig.#4
Adhesive
Sealant
Drill the faucet holes.
Install the faucet to the countertop according to the
manufacturer's instructions.
Install the drain to the lavatory according to the
installation instructions included with the drain. Apply a
sufficient amount of clear silicone sealant when you
install the drain.
-3-
CAUTION: Risk of personal injury or product
damage. Large lavatories are very heavy. Get
help lifting the lavatory into place.
Note the location of the "Kohler" logo. The lavatory
should be installed so the logo is visible after
installation.
Carefully position the lavatory in the cutout, and press
down firmly.
Fig.#5
"Kohler" Logo
Connect the faucet supply lines.
Connect the drain assembly.
Open the faucet valves, and check for leakage.
Clean up with a non-abrasive cleaner.
Nut Gasket
Nut
Gasket
Fig.#6
1007250-K01-A

CLEANING YOUR VESSELS LAVATORY
Keep your vessels lavatory looking new by rinsing it out
thoroughly after each use. Do not regularly use
abrasives on the lavatory surface, as this will eventually
scratch and dull the surface. For stubborn stains,
abrasives may be used sparingly.
THIS TAG IS FOR REMOVAL BY
HOMEOWNER ONLY!
Treat your decorative product just as you would treat
your fine china. The best way to clean it is to use warm
water and pat dry with a cotton cloth or soft sponge.
use bristle brushes or abrasive-backed
sponges. They will scratch the decorative surface.
For occasional cleaning of stubborn deposits, use
ONLY the following cleaners: apply the cleaner, wipe
gently, . Pat dry or
wipe gently with a cotton cloth.DO NOT
rinse off any residue immediately
USE & CARE
-4-
IMPORTANT CONSUMER INFORMATION
LIMITED ONE-YEAR WARRANTY
Kohler plumbing fixtures and fittings are warranted free
of manufacturing defects.
To obtain warranty service, contact Kohler either
through your Dealer or Plumbing Contractor or by
writing Kohler Co., Attn: Consumer Affairs Department,
Kohler, WI 53044 U.S.A.
Some states do not allow limitations on how long an
implied warranty lasts or the exclusion or limitation of
incidental or consequential damages, so this limitation
and exclusion may not apply to you. This warranty
gives you specific legal rights. You may also have rights
which vary from state to state.
This is our exclusive written warranty.
KOHLER CO., KOHLER, WISCONSIN 53044
Kohler Co. will, at its election repair, replace, or make
appropriate adjustment where Kohler Co. inspection
disclosed any such defects occurring in normal usage
within one year after installation.
Co.
I
Kohler Co. is not
responsible for installation costs.
MPLIED WARRANTIES, INCLUDING THAT OF
MERCHANTABILITY, ARE EXPRESSLY LIMITED IN
DURATION TO THE DURATION OF THIS
WARRANTY. KOHLER Co. DISCLAIMS ANY
RESPONSIBILITY FOR CONSEQUENTIAL
DAMAGES.
1007250-K01-A