KOLAR LAURA 60 User manual

Cooker hood
Instruction Manual
SANTA 60
LAURA 60
CUBIX 60
ERIKA 90
VICTORIA 90
◆PLEASE READ THE MANUAL CAREFULLY BEFORE OPERATION◆

Dear customer：
Your new hood was manufactured in a state of the art facility
and has passed the strictest quality control procedures.
The rang hood fan extracts the kitchen vapours and passes them
through the grease filter. The grease filter absorbs the solid
particles in the cooking vapors, keeping the kitchen almost free
of grease.
This manual will provide you with information on how to
operate and care for your hood to gain the maximum benefit
from it.
For you to better use this product, please read the instructions
carefully before you use it, and keep it for latter reference!
Important information
1. This section contains safety instructions that will help you
avoid risk of injury and damage. All warranties will be void if
you do not follow these instructions.
2. This guide to installation and use is valid for several models.
Minor differences in details and fittings may emerge between
your appliance and the description provided.
3. The manufacturer strives for continuous improvement. For
this reason, the text and illustrations in this manual are subject to
change without notice.
4. Figures in this manual are schematic and may not exactly
match your product.
5.The rang hood is used on 220/240v, 50Hz.

Contents
A. Precautions -------------------------------------------------P4-5
B. Installation --------------------------------------------------P5-7
C. About the switch--------------------------------------------P7-9
D. Circuit diagram---------------------------------------------P9
E. Maintenance-------------------------------------------------P10-12
F. Trouble shooting--------------------------------------------P12-13

Precautions
1.To avoid accident, installation should be performed by
professionals.
2.Before installing and using the range hood, ensure the voltage and
frequency specified on the range hood are right.
3.To ensure safety and smooth installation, use supplied accessories
for installation, mounted on the walls with enough strength to
support the hood ,or the range hood may drop.
4.While boring or mounting screws on the walls for installing the
range hood on, be aware of the structure and materials of the wall
and keep away from the electric wires and water pipes, etc. in the
wall.
5.Use the original exhaust pipe supplied with the range hood.
6.The range hood shall not share the exhaust pipe with any other
facilities, such as heating pipeline, gas pipeline, water heater, etc.
7.When installing exhaust pipe, ensure its bent angle shall be ≥120°,
and it shall be not lower than the starting point while it runs outdoor.
8.The range hood shall have reliably grounded power plug, or else it
is forbidden to use.
9.Unplug the power supply in case the range hood lays idle for long
time.
10.If any electric part of the range is damaged, replace with new one
of the same specification.
11.This rang hood was designed for used by private person in their
homes, should not be used in special environment.
12.This hood is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities or lack of

experience and knowledge, unless they have been given supervision
or instruction concerning the use of the hood by a person responsible
for their safety.
13.Electrical products are dangerous to children. Keep children away
from the hood when it is operating and do not allow them to play
with the hood. The packaging materials will be dangerous for
children. Keep the packaging materials away from children.
14.Always unplug the hood before cleaning it or performing other
maintenance acts.
Installation
1.In order to ensure the effect of suction and exhaust of the
appliance, it should be
installation should avoid Windows and doors around too much.
And the center of the range hood is 650-750mm away from the
upper surface of the cooker (See Fig. 1).
2.The perfect position should take the safe situation of the gas stove
or other cookers into consideration.
3.The horizon distance from the air outlet to the body should keep
more than 1.5m，and the turn radius as long as possible.
4.After the mounting height and position are fixed, fix the
suspension loop at appropriate position. Note: the top of the
enclosing board is the highest mounting point for the range hood (as
in Fig. 2).
5.Fix the exhaust pipe on the range hood, bind with sealing tape(as
in Fig. 3).
6.Use screws to fix the enclosing boards on the range hood. (as in
Fig. 4)
7.Lift up the range hood, fix it with the suspension loop. (as in Fig.
5). Note: Ensure the range hood is properly fixed before loosening
grip.

8.Inspection the body levelness of the range hood in case the grease
cup inner learn to one side. (as in Fig. 6)
Fig.1 Fig.2
Fig.3
Fig.4 Fig.5

Fig.6
About the switches and circuit diagram
I. About the use of electronic switches (as in Figure 7)
Fig.7
2. On/Off: Pressing the “On/Off” button once, the power indicator
light goes on, start-up music sound, pressing once again, every
function goes off. During the motor running, press the “On/Off”
button once to enter the state of delay within two minutes. After the
two minutes, power off
Pressing “On/Off” button once, the power indicator light and
backlight goes on, then press “Fast” button once, the motor runs at
fast speed, press “Fast” button once again, the motor stop running.
Pressing “On/Off” button once, the power indicator light and
backlight goes on, then press “Medium” button once, the motor runs
at medium speed, press “Medium” button once again, the motor stop
running.
Pressing “On/Off” button once, the power indicator light and
backlight goes on, then press “Slow” button once, the motor runs at
slow speed, press “Slow” button once again, the motor stop running.
Time: Pressing “Time” button once, hour system start flashing every
1 second for 8 seconds. Press “Time” button to increase time and
“Slow” button to decrease time during flashing. Pressing “Time”

second time to confirm the hour system and minute system flash.
Pressing “Medium” button to increase time and “Slow” button to
decrease time and “Time” once more to confirm the minute system
during the 8 seconds.
Light: Pressing “Light”button once，the light goes on ,press once
more ,the light goes off.( “Light” function works independently and
do not subject to “On/Off” control .)
II.About the use of push button(as in Fig.8)
1.Press “P”, the motor will be off.
2.Press the button to “low”, “middle” and
“high”,the motor will be turned on at “ low”,
“middle” and “ high” speed respectively.
3.Press “light”, the light will be on. Press it
again,the light will be off.
III .About the use of push button(as in Fig.9)
1.Power on,hum once, then all indicator light on within one
second,LCD screen shows"12:00" and starts the countdown.It will
be on state of standby after the background indicator lights on
within ten seconds.
2.Press" timing" button last three seconds,hum once,the LCD screen
show"12:"flashing,touch the button "speed" to increase the hour
system,touch the button"timing" once,the LCD screen
show":00"flashing,touch the button"light"to increase the minute

system.It will be save the settings within ten seconds not operation
any more or Second touch timing key to exit the state of setting.
3.Press the "Speed" key once ,the motor runs in high speed; Press
twice, the motor runs in medium speed; Press three times ,the motor
runs in slow speed.
4.When the motor runs: touch your "timing" key to set the shutdown
state.
5.Touch the "light" key once ,the lights go on ;Touch twice ,the light
go off.
6.The motor works condition to touch the "on/off" key once, 60
seconds delay shutdown, the LCD shows "1:00" and start the
countdown at once, "on/off "indicator lights flashing, it will be the
delay shutdown state, after the end of the countdown motor stopped
working , in the process of delay shutdown , touch the keys again its
motor will immediately.
7.Touch the "Auto" key once,the LCD shows "Auto" after one
minute,the smoke preheating successfully start automatic function.
8.The "Remote" key is corresponding to the panel buttons function.
Circuit diagram(as in Fig.9)
N L
BLUE
YELLOW/GREEN
BROWN
LED
WHITE
YELLOW
BLUE
ORANGE
BLACK
LED FEELING SCREEN BUTTON
RED
C
M
CONTROL PANEL
BLACK
RED
70
56
Fig.9

Maintenance
To let the range hood have the best performance and longest life,
frequent maintenance is necessary.
Note:
1. Unplug the power cable before doing maintenance, and press the
“On/ off”button to ensure it is off.
2. Wear protective gloves in maintenance.
Cleaning the metal grease filters
1.In normal operation(1 to 2 hours daily),the metal grease filters
must be cleaned every 8 to 10 weeks.
2.Dip metal grease filters into clear water about 40-50℃, add
cleaning agent and soak for 2-3 minutes, wash with soft-haired
brush, avoid damaging the filtering screen (aluminum screen).
3.May be rinsed in dishwasher. Add cleaning agent, bring the
temperature to about 60℃.
Note: Filtering is all metal. Cleaning agent corrosive to metals shall
not be used in cleaning. If cleaning is not carried out in accordance
with the instructions, the accumulated grease could, over time,
become a fire risk.
Replace the active carbon unit
Take down the active carbon unit in the direction of the arrow and
replace new one. (as in Fig. 10)Under normal conditions (work one
to two hours every day, replace with new one every six month).Have
been used active carbon should be discarded together with living
garbage.
Fig.10

Cleaning procedure
1.Routine cleaning will preserve the corrosion resistance and the
appearance of the
stainless steel for many years.
2. Put in new active carbon granules, mount the active carbon unit
back in the range hood.
3. Clean the stainless steel as often as necessary (i.e. when it is
noticeably dull
or dirty) and use the simplest cleaning method that will effectively
do the job.
4.Use clean water, or a mild detergent solution applied with a soft
cloth or sponge. rinse well and wipe dry.
5. Always wipe in the direction of the brushed texture on the
stainless steel.
6. Periodically apply a fine film of dedicated stainless steel cleaner
or baby oil
to the canopy of the extractor hood to add lustre and sparkle to the
steel.
Owner’s responsibility
NOTE: Since the following are not factory faults, they are the
owner’s responsibility.
1.Damage to exterior finish.
2.Breakage of glass and other components
3.Replacement of the light bulbs
4.Damage through improper use or installation
Trouble shooting
Fault
Cause
Solution
Light on, but motor
does not work
The leaf blocked
Get rid of the
blocking
The capacitor damaged
Replace capacitor
The motor jammed bearing
damaged
Replace motor
The internal with of motor
off or a bad smell from the
motor
Replace motor
Beside the above mentioned, check the following:

Light does not
work, motor does
not work
Light damaged
Replace lights
Power cord looses
Connect the wires as
per the electric diagram
Oil leakage
One way valve and the air
ventilation entrance are not
tightly sealed
Take down the one
way valve and seal
with glue
Leakage from the
connection of U-shaped
section and cover
Take U-shaped section
down and seal with
soap or paint
Shake of the body
The leaf damaged and
causes shaking
Replace the leaf
The motor is not tightly
hanged
Lock the motor tightly
The body is not tightly
hanged
Fixed the body tightly
Insufficient suction
The distance between the
body and the gas top too
long
Readjust the distance
Too much ventilation from
open doors or windows
Choose a new place
and resemble the
machine
The machine
inclines
The fixing screw not tight
enough
Tighten the hanging
screw and make it
horizontal
The hanging screw not
tight enough
Tighten the hanging
screw and make it
horizontal
※IF ANY PROBLEM CANNOT BE RECTIFIED PLEASE
CONTACT THE ANGENT IN YOUR STATE OR THE
DISTRIBUTOR SERVICE DEPARTMENT.