Kolin KCF-10SRD User manual

STANDING
CIRCULATION FAN
INSTRUCTION MANUA
Model:KCF-10SRD
Please read the instructions carefully before using this product.
INSTRUCTION MANUAL

PRODUCT PARAMETERS
Product name：Standing Circulation Fan
Model：
Adapter：
KW-MF02RDADC24V，
1A
Motor：DC Motor
Rated power：24W
Product size：330X330X925mm
Net weight：
Packing list：
2.3kg
Folding fan x 1、Support tubes x 2、Base x 1、
Remote control x1、User manual x1、Power adapter x1
POWER ADAPTER SPECIFICATION
Input data：AC100-240V，50/60Hz
Output date：DC24V，1A
WIRING DIAGRAM
M
PERFORMANCE FEATURE
The height of the fan can be adjusted by Support tubes or a combination of Iron
Pipes, through different combinations can adjust the fan to be different heights,
which can be used as standing fan or desktop fan; it is suitable for offices, homes,
dormitories, etc.,
Adjustable wind speed from 1to 9 grades, adjustable timing from 1 to8 hours.
Remote control operation, more comfortable to use.
Wide-angel air supply. The oscillation angle can reach 120° while the tilting
head up to 100° (some models).
FAN
PCB
board
KCF-10SRD
Fan head x1
Wide-angle
.
using different combinations of
Support tubes found in this package. It can be used as standing fan or
desktop fan suitable for offices, homes, dormitories, etc.
Timer setting from 1 to 8 hours.
.

PRODUCT SIZE
330mm 330mm
925mm

MAIN PARTS
Outlet housing
Inlet
housing
Status panel Body
Tilt
adjustment
Oscillate
Timer
Wind
speed
Support
tube 2
Support
tube 1
Base
On/Off
On/Off
Left & Right
oscillation
Tilt oscillation
Timer
Wind speed+
Wind speed-
Remote-control unit
(For the first time, please pull out
the battery insulation sheet)
Output
plug
Adapter
input plug

Figure 1
Body
3
Support
tube 2
2
Support
tube 1
1
Base
Figure 2
or
or
Standing Fan Standing Fan
status 1 status 2
desktop fan
status
INSTALLATION
Notice: Do not insert the adapter output plug into the body when
installing fans.
1. Install Support tube 1 into hole of the base, and install Support tube 2 into
corresponding hole of Support tube 1,then install the combined part into the
top body, rotate clockwise until all parts are tightened. (Refer to Figure 1)
2. The Support tube can be disassembled, just connect the top body to the
base, and it can be used as desktop fan. (Refer to Figure 2)
USE GUIDE
After assembling the fan components according to installation requirements,
place the fan on a smooth ground or table top, insert the power adapter
output plug (DC24V 1A) into the power input port at the bottom of the fan
head, and then insert the adapter input plug into the household power socket.
After the preparation, the fan can be controlled by the touch switch on the
control panel, or the remote control can be used to control the operation.
(Before using the remote control, remove the battery isolation strip at the
end of the remote control)
assembling the fan.

OPERATING INSTRUCTION
Timer shutdown
indicator
Display current wind
speed or auto
shutdown time
Tilt
Oscillation
100°
120°
90°
60°
h Timer
Wind speed
Angle of tilt oscillation
On/ Off Angle of left and
right oscillation
1. On/off
After the power is switched on, press the switch button “”in standby state,
and the fan enters l speed working mode. Press the switch button again, and
the machine enters standby state.
2. Wind speed adjustment
After the fan is turned on, when touch the wind speed button “”lightly, the
wind speed will increase by 1 speed according to the current speed every time.
If wind speed is adjusted to 9 speed, press the wind speed button again and
the gear will continue to circulate from 1 speed.
3. Timer setting
After the power is switched on, press the switch button “” in standby state, and
the fan enters l speed working mode. Press the switch button again, and the
machine enters standby state.
4. Oscillation setting
When the fan is running, tap the oscillation button “” to enable the oscillation
function. The angle of oscillation is 60 degrees. Tap the oscillation button once,
and the angle of the oscillation increase to 90 degrees and 120 degrees
successively until the oscillation function is closed.
5. Tilt setting
When the fan is running, tap the tilt oscillation button “” to enable the fan tilt
oscillation function. The fan tilt angle is 100°. Tap the tilt oscillation button again
to turn off the tilt oscillation function.
After the plugging in of the unit, press the On/Off button
On/Off
After the switching on of the fan, touch the wind speed button
After the switching on of the fan, touch the wind speed button
After the turning on of the fan, press the timer button
Press the timer button consecutively to set the time of operation from 1 hour up
to 8 hours. To remove timer, press the timer button until "0h" appears.
the control panel.
Tapping the button continuously,
the angle of oscillation will be increased

COMPONENT DISASSEMBLY INSTRUCTION
FRONT HOUSING DISSASSEMBLING
1
Turn the phillips screwdriver
counterclockwise to remove
the outlet housing screw
2
Rotate the outlet housing
counterclockwise to unlock
3
Remove the outlet
housing
BLADE DISASSEMBLING
4
Rotate clockwise to release blade lock
5
Draw blade forward to remove blade
Obverse of blade
REAR HOUSING DISASSEMBLING
6
Turn the phillips screwdriver
counterclockwise to remove
the inlet housing screw
7
Rotate the inlet housing
counterclockwise to unlock
8
Remove the inlet housing

NOTES：
Please use the power adapter provided with the product. Before use,
please make sure that the input voltage is used as required by the adapter
within the voltage range (Adapter input : AC100-240V, 50/60Hz; output:
DC24V, 1A).
The user is not allowed to disassemble and replace the internal parts of the
fan at will. If there is any fault, please contact the after-sales service depart-
ment for repair.
If this product has technical improvements in the future, will not notify other-
wise.
If the appearance and color of the product are changed, please refer to the
actual product.
This product wind is strong, so suggest not to blow directly to babies and
the elderly for a long time.
When the power cord or product is found to be damaged or unsafe, please
suspend use, and contact the factory or its after-sales service agents, or
qualified personnel to replace. Do not repair and check by yourself.
Children, elderly or patients who have lost the ability to take care of them-
selves should use this product under adult supervision to prevent acci-
dents.
This product should be placed out of reach of children, and the children
should be taught correctly. Do not use this product as a toy.
In order to avoid electric shock, no part should be in contact with water.
There can be no objects blocking the air inlet/outlet.
Please use this product in an environment of 0~40℃. Don't put the fan in
the bathroom, humid or very high temperature place, so as not to damage
the product.
Please keep the fan away from soft objects such as curtains and door cur-
tains to avoid getting caught in the fan.
Please unplug the power plug before cleaning or moving the product.
When the fan is not used for a long time, please unplug the power plug to
prevent the product from shortening the product life and causing accidents
or dangers in the standby state for a long time.
Product features and specification are subject for change without prior
notice.
Avoid aiming directly to babies and elderly for a long time as the product
wind is strong
the use. Contact the Authorized Service Center or its after-sales
service agents to replace the product. Do not repair and check by yourself.
to avoid damaging

Do not put fingers, other body parts or debris into the air inlet/outlet to avoid
injury and damage to the product.
Do not put wet towels or wet wipes on the product to avoid electric leakage
and electric shock accidents.
When removing the protective shell for cleaning, be careful not to touch the
touch buttons to avoid accidents in the operation of the product.
Please do not throw this product away with other household
waste. When it is no longer used, the product must be sent to
the appropriate department for recovery and recycling. For
information about the collection system, please contact your
local government. If you place electrical appliances in a landfill
or garbage dump, harmful substances may seep into the
groundwater, enter the food chain, and harm your health and
life.
CLEANING MAINTENANCE AND SAFETY MATTERS
1. When cleaning, maintaining or moving the product, you must first turn off the
product and then unplug the power cord.
2. The fan must be completely stopped before it can be cleaned to avoid injury.
3. Do not immerse the power cord or main unit in water for cleaning or wash it
under a faucet. The internal parts of the fan must not be wetted.
4. Do not use detergent, wire brush, gasoline, alcohol, vinegar or other volatile
corrosive liquids to clean the product to avoid damage to the product.
5. Clean the surface of the fan with a slightly damp cloth.
6. After cleaning, the product must be complete dry before it can be connected
to the power supply
7. If you will not use it for a long time, please store the product back in the box
and store it in a dry, cool and safe place.
If you place electrical appliances in a landfill or garbage dump,
harmful substances may seep into the groundwater, enter the food
chain and harm your health and life.

6. After cleaning, the product must be completely dry before it can be connect-
ed to the power supply.
7. If you will not use it for a long time, please store the product back in the box
and store it in a dry, cool and safe place.
8. The humidifier needs to take the absorbent cotton out of the product, and
gently squeeze the water out, then place the absorbent cotton in a dry and
ventilated place, let it dry naturally and store or use it again; clean the atomized
sheet part with a soft brush.
9. When cleaning the outer surface of the humidifier, dilute it with a neutral mild
detergent, and then wipe it with a cloth dampened with it.
TROUBLESHOOTING
FAULT
DESCRIPTION
CAUSE
ANALYSIS
TREATMENT
MEASURES
Machine
can't work
The adapter is not
plugged in.
Plug intheadapter
power cord plug.
No power supply.
Replace power supply.
The switch button is
not pressed.
Press the switch
button again.
Abnormal
sound
Wind leaf cracking.
Replace the fan blades.
Motor damage.
Replace the motor.