kollectaball K-Pro User manual

K-Pro comes unassembled to
allow for more cost-eective and safer
shipping. Assembly will require roughly
40 minutes for a rst-time assembler.
IF YOU REQUIRE ASSEMBLY ASSISTANCE,
WE ARE HERE TO HELP.
CALL TOLL FREE 1-888-985-1009 OR
EMAIL [e-mail]
K-Pro Assembly InstructionsK-Pro Assembly Instructions
Thank-you for purchasing a K-Pro Golf Ball Collector.Thank-you for purchasing a K-Pro Golf Ball Collector.
The K-Pro is a premium golf ball picker-upper thatThe K-Pro is a premium golf ball picker-upper that
collects 80 balls in seconds and comes with acollects 80 balls in seconds and comes with a
built-in dispensing unit with a strong handle andbuilt-in dispensing unit with a strong handle and
stand so you don’t have to leave it on the green.stand so you don’t have to leave it on the green.

Before assembly, the following
tools are required:
1. Protective Eye wear
2. Flat Head Screwdriver
3. Pliers
1. Wire Mounting Disk
(R090) x 2
2. Cage Holder (R182)
3. Stand (R227)
4. Wire Opener (R195)
5. Tension Wire
6. Wire (R101) x 62
7. Handle Lower Section
(R211)
8. Handle Upper Section
(R210)
9. Cam (R235)
10. Allen Key
11. Wire Removal Tool
(R062)
12. Wrench
13. Hex Screw (R198)
14. Screw (R050) x 2
15. Lock Nut (R137) x 5
16. Bolt (R197) x 2
17. Washer (R178) x 2
18. Coupler (R219,
Inside Handle)
1
2
34
5
6 7 8
9
10
11 12 14 15 16 17
18
13
1
2 3

STEP 1: Assembling the Cage
STEP 2: Assembling the Handle
Remove the R219 Coupler
from inside the R210 Handle
Upper Section and remove both
Allen Key Screws.
Join the two sides of the Coupler and
insert into the R210 Handle Upper Section
so that the hole in the Coupler is aligned
with the hole in the Handle. Insert an
Allen Key Screw in the Handle to secure,
but do not tighten all the way.
Slide the R211 Handle Lower Section over
the exposed coupler so the holes align.
Insert the second Allen Key Screw and
tighten both using Allen Key.
DO NOT OVERTIGHTEN.
The numbered white sticker on the mounting disk helps to indicate the next available slot. Insert one wire (R101) as shown into
slot #1 on the mounting disk. You will hear it click into place. DO NOT INSERT THE WIRE UPSIDE DOWN. Being careful not to
miss any slots, continue inserting wires in numeric order until all 60 slots are full. Take the second disk, face the silver section of each
disk towards each other, then insert the other end of the wires into the 60 slots in numeric order. Remove the white stickers and
store the 2 extra wires in case damaged wires need to be replaced in the future.
X
Take the centre tensioning bar and push one end into one of the four slits in the centre of the wire mounting disc.
Repeat on the other wire mounting disc.

STEP 3: Wire-Opener and Stand Assembly
STEP 4: Attaching the Cage to the Cage Holder
Insert the R211 Handle Lower
Section through the R195Wire
Opener.With the Wire Opener in
the position shown, twist the handle
90 degrees and slide theWire
Opener up so the holes on the Wire
Opener and Handle are aligned.
Place R178 washer on one side of the
wire-opener with the at side facing
outwards and insert R198 hex screw.
Place the second R178 washer on the
other side and tighten the R198 screw.
Fasten with R137 lock nut.
Insert R182 Cage Holder into
the handle, but DO NOT FASTEN.
Remove the lock nut from R235 Cam
and insert as shown in the above
image. Secure with the lock nut,
but ONLY FINGERTIGHT.
Fasten the Cage Holder to the handle using the
two R197 bolts and the R137 lock nut. Be sure to
insert the bolts from below with the lock
nut on top. Insert BOTH bolts and fasten hand
tight BEFORE tightening with the wrench.
Using a at head screwdriver and pliers, fasten R227 Stand to the wire
opener using the R050 screws and R137 lock nuts. Be sure to insert the
screw from the top with lock nut underneath. Fasten tightly.
Align the holes on the ends of the cage with
the cage holder and squeeze into place.
Note the direction
of the stand
Kollectaball is a trade mark of IntoEuropeSales Ltd. Distributed in North America by RCS Sports
You are
now ready
to enjoy
your
Kollectaball!