komodo SP5736 User manual

SP5736
USER MANUAL
Keep this manual for future reference
QUESTIONS, PROBLEMS, OR MISSING PARTS?
Please Contact Customer Service Before Returning to Store
Please carefully check the unit and make sure there is no damage when you open the carton.
[email protected] [phone]
www.soupro.com

• GENERAL INFORMATION
FCC/ICSES Information
Safety Instructions
Warranty
• ASSEMBLY INSTRUCTIONS
Preparation
Assembly
• FIREPLACE OPERATIONS
Operating Instructions
Care And Maintenance
Troubleshooting
Table of Contents
Safety Instructions
2
GENERAL INFORMATION
Use this rebox only as described in the manual. Any other use is NOT recommended by the manufacturer and may cause
re, electric shock or injury to persons.
CAUTION:
• If possible, ALWAYS unplug this rebox when not in use.
• DO NOT operate any rebox with a damaged cord or plug or after the heater malfunctions.
• DO NOT operate any rebox if it has been dropped or damaged in any manner. Disconnect power at service panel and have
rebox inspected by a reputable electrician before reusing.
• Any repairs to this unit should be carried out by appropriately qualied service personnel.
• Under no circumstances should this unit be modied. Parts having to be removed for servicing must be replaced prior to
operating this unit again.
• DO NOT use outdoors.
• This unit is not intended for use in bathrooms, laundry areas and similar indoor locations. NEVER place heater where it may
fall into a bathtub or other water container.
• To disconnect this unit, turn all controls to the OFF position, then remove plug from outlet.
• ONLY connect to properly grounded outlets.
• This appliance, when installed, must be electrically grounded in accordance with local codes, with the current CSA C22.1
Canadian Electrical Code or, for USA installations, follow the National Electrical Code, ANSI/NFPA NO.70.
This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to part 15 of the FCC
rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
The equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on. The user is encouraged to try and correct the interference by one or more of the following measures:
(a) Reorient or relocate the receiving antenna
(b) Increase the separation between the equipment and the receiver
(c) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
(d) Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(a) This device may not cause harmful interference, and
(b) This device must accept any interference received, including interference that may cause undesired operation.
Modications not approved by the party responsible for compliance could void user’s authority to operate the equipment.
This Class B digital apparatus complies with Canadian ICES-003.
FCC / ICES Information
2
2
4
5
7
13
14
15

Please read and understand this entire manual before attempting to assemble, operate or install the product.
IMPORTANT NOTICE
When using electrical appliances, basic precautions should always be followed to reduce the risk of re, electric shock
and injury to persons, including the following:
WARNING: Place this unit in a location that avoids direct sunlight and high temperatures.
WARNING: Plastic bags, nails, etc. should be kept out of reach of children.
WARNING: This appliance is hot when in use. To avoid burns, DO NOT let bare skin touch hot surfaces. Keep
combustible material, such as furniture, pillows, bedding, papers, clothes and curtains, at least 3 feet from the front
of the heater and keep them away from the side and rear.
WARNING: Extreme caution is necessary when any heater is used by or near children or individuals with
disabilities and whenever the replace is left operating and unattended.
WARNING: DO NOT run cord under carpeting. DO NOT cover cord with throw rugs, runners, or similar covering.
Do not route cord under furniture or appliances. Arrange cord away from traffic areas and where it will not be
tripped over.
WARNING: DO NOT insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause
an electric shock or re, or damage the appliance.
WARNING: This appliance has hot and arcing or sparking parts inside. DO NOT use it in areas where gasoline,
paint or ammable vapors or liquids are used or stored. This replace should not be used as a drying rack for
clothing. Christmas stockings or decorations should not be hung in the area of it.
3
GENERAL INFORMATION
• To prevent a possible re, DO NOT block any air intakes or exhaust in any manner. DO NOT use on soft surfaces, like a
bed, where opening may become blocked.
• ALWAYS plug this unit directly into a wall outlet/receptacle. NEVER use with an extension cord or relocatable power tap
(outlet/power strip).
• This heater includes an automatic protection system that will shut off the unit to prevent overheating. If the unit is at risk of
overheating, the front panel will display "E1" and a thermal cut out will shut off the heater to prevent damage or risk of re.
• DO NOT place any objects on top of rebox and top air intake vents as this will cause the unit to overheat and can cause a
re.
ELECTRICAL CONNECTION:
• A 15-amp, 120-volt, 60 Hz circuit with a properly grounded
outlet is required. Preferably, the fireplace will be on
a dedicated circuit as other appliances on the same
circuit may cause the circuit breaker to trip or the fuse
to blow when the heater is in operation. The unit comes
standard with 6-ft. three-wire cord, exiting from the rear
of the fireplace. DO NOT exceed the current rating of
the current tap. ALWAYS plug this unit directly into a wall
outlet/receptacle. NEVER use with an extension cord or
relocatable power tap (outlet/power strip).
• This rebox is for use on 120 volts. The cord has a plug as
shown below. See illustration for grounding instruction. An
adapter as shown at C is available for connecting three-
blade grounding type plugs to two-slot receptacles. The
green grounding lug extending from the adapter must
be connected to a permanent ground such as a properly
grounded outlet box. The adapter should not be used if a
three-slot grounded receptacle is available.
Grounding Pin
Grounding Pin
Grounding Means
Adapter
A
C
B
D
Metal Screw
Cover of
Grounding Box
ELECTRICAL SPECIFICATIONS
Voltage:
Amps:
Watts:
120 VAC, 60 Hz
11.7 Amps
1400 Watts

Warranty
1-YEAR LIMITED WARRANTY
Soupro Limited Inc. (hereinafter referred to collectively as “the Company”) warrants that your new KOMODO Electric
Fireplace is free from manufacturing and materials defects for a period of one (1) year from date of purchase. Subject to the
following conditions and limitations:
1. The electric fireplace must be installed and operated at all times in accordance with the installation
and operating instructions furnished with the product. Any unauthorized repair, alteration, willful abuse,
accident, or misuse of the product shall nullify this warranty.
2. This warranty is non-transferable, and is made to the original owner, provided that the purchase was
made through an authorized supplier of the Company.
3. The warranty is limited to the repair or replacement of part(s) found to be defective in material or
workmanship – provided that such part(s) have been subjected to normal conditions of use and service –
after said defect is conrmed by the Company’s inspection. All replacement parts or products will be new,
remanufactured, or refurbished.
4. The Company may, at its discretion, require that any defective part(s) be returned in exchange for the
replacement part(s).
5. The Company may, at its discretion, fully discharge all obligations with respect to this warranty by
refunding the wholesale price of the defective part(s).
6. This warranty does not cover the LED light bar included with the electric replace.
7. Any installation, labor, construction, transportation, or other related costs/expenses arising from defective
part(s), repair, replacement, or otherwise of same, will not be covered by this warranty, nor shall the
Company assume responsibility for the same.
8. The owner/user assumes all other risks – if any – including but not limited to the risk of any direct, indirect
or consequential loss or damage arising out of the use, or inability to use the product, except as provided
by law.
9. All other warranties – express or implied – with respect to the unit, its components and accessories, or
any obligations/liabilities on the part of the Company are hereby expressly excluded.
10. The Company neither assumes, nor authorizes any third party to assume on its behalf, any other liabilities
with respect to the sale of the unit.
11. The warranties as outlined within this document do not apply to non-accessories used in conjunction with
the installation of this product.
12. This warranty gives you specic legal rights, and you may also have other rights which vary from state to
state.
This warranty is void if:
(a) The replace is subjected to prolonged periods of dampness or condensation.
(b) Any unauthorized alteration, willful abuse, accident, or misuse of the product.
(c) You do not have the original purchase receipt.
4
GENERAL INFORMATION
IF WARRANTY SERVICE IS NEEDED
Please Contact Customer Service
Make sure you have the following information ready:
• Warranty
• Sales Receipt
• Product Model/Serial Number
• Date of Purchase
• Location of Purchase
[email protected] [phone]
www.soupro.com

Preparation
IMPORTANT INFORMATION
1. Before you begin, locate the instructions and hardware. Be sure you have all of the parts and can identify
them.
2. To avoid scratching the finish, assemble the product on a soft, non-abrasive surface such as carpet or
cardboard.
3. Assembly of this product may require more than one person.
4. Select a location that is not susceptible to moisture, dust and is away from high trafc locations and things
that many catch re or block openings such as drapes, pillows, furniture etc.
5. It is strongly recommended that the screws be screwed into the wall studs where possible. If the wall studs
cannot be used, wall anchors must be used.
CAUTION: Enclosed wall anchors (BB) only can be use on the concrete wall.
6. For the best effect install the replace out of direct sunlight and away from overhead lighting.
Tools Required
Philips Screwdriver Hand Drill Hex Key
5
ASSEMBLY INSTRUCTIONS
Site Selection
WARNING: This appliance is hot when in use. To avoid
burns, DO NOT let bare skin touch hot surfaces. Keep
combustible material, such as furniture, pillows, bedding,
papers, clothes and curtains, at least 3 feet from the front of
the heater and keep them away from the side and rear.
Minimum clearance of the replace to the adjacent wall
Sides ------------------------------- 6 inch / 15 cm
Floor ------------------------------- 6 inch / 15 cm
Top ------------------------------- 6 inch / 15 cm
Back ------------------------------- 0 inch / 0 cm
Select a location that is not susceptible to moisture, dust and is away from high trafc locations and things that many
catch re or block openings such as drapes, pillows, furniture etc.
Min.
6 inch
Min. 6 inch
Min. 6 inch

Parts List
Preparation
6
ASSEMBLY INSTRUCTIONS
x 1
x 1
x 1
A
C
B
Front Cover
Base
Fireplace
x 1
x 1
x 1
Mounting Bracket
Remote Control
Acrylic Shards
D
E
F
AC
D
BE
F
Number of spare hardware is indicated in ( ).
Hardware Identication
BB x 8AA x 8 + (1)

Assembly - Wall Mount Installation
7
ASSEMBLY INSTRUCTIONS
2.
1. Remove mounting bracket (D) from back of replace (C) by unscrew two screws at the top
of the unit.
D
Remove the base (B) of replace (C) by unscrewing three screws at the rear base of the
unit.
B
B
C

8
ASSEMBLY INSTRUCTIONS
Assembly - Wall Mount Installation
3.
4.
Choose a wall location to attach the mounting bracket (D). Position the mounting bracket (D) in the
desired location. Use a level to align the bracket and mark the eight holes with a pencil.
D
Select the hardware appropriate for mounting bracket installation.
STUD WALL
• Secure the mounting bracket (D) to wall using screws (AA) at marked stud locations.
DRYWALL
• Drill holes at marked locations and secure the mounting bracket (D) to the wall with toggle
bolts and washers (not included).
CONCRETE WALL
• Drill 5/16-inch holes at marked locations, then insert wall anchors (BB) into holes. Secure
the mounting bracket (D) to wall using screws (AA).
STUD WALL DRYWALL CONCRETE WALL
D
D D
AA BB
AA
Minimun height: 16in

Assembly - Wall Mount Installation
9
ASSEMBLY INSTRUCTIONS
5.
6.
Hang the fireplace (C) on the hooks at bottom of mounting bracket (D) and push the
replace (C) into mounting bracket (D).
Re-fasten the two screws as shown.
C
C
C
D
D
D

10
ASSEMBLY INSTRUCTIONS
Assembly - Wall Mount Installation
7. Distribute the Acrylic Shards (F) evenly in the tray of the replace (C).
8. Re-install the front glass (A) to the replace (C).
F

Assembly - Free Standing Installation
11
ASSEMBLY INSTRUCTIONS
1. Distribute the Acrylic Shards (F) evenly in the tray of the replace (C).
F

12
ASSEMBLY INSTRUCTIONS
Assembly - Free Standing Installation
2. Re-install the front glass (A) to the replace (C).

Operating Instructions
13
FIREPLACE OPERATIONS
°F
°
C
PM
AM
• HEATER key is used to control ON/OFF of the heater.
Push UP (“+”) or DOWN (“-”) key to to scroll through
the pre-set temperature range from 59°F (15°C) to
86°F (30°C), ON & OF (OFF). Heater will turned ON
accordingly to the set temperature. When the ambient
temperature is higher than the set temperature, heater
will automatically turned OFF.
• When the temperature is set at “ON”, heater will be
working continuously.
• When HEATER is activated, the heater & temperature
symbol will displayed.
• When the heater is ON, hold the HEATER key for 3
sec; this allow the temperature unit change from °C to
°F or °F to °C. The unit default setting is °F.
• Press the POWER button to turn ON or OFF the unit.
• When the unit is in ON mode, touch control panel light
will fully light up for 8 sec and then shut down if without
any others operation including remote control.
• When the unit is in OFF mode, the POWER symbol
LED will Semi-bright. When power OFF, unit will be
stopped, if heater is working before power OFF the
unit, fan will have 20 seconds delay to ensure heat will
not be trapped inside the unit.
• Press the ame button to cycle through the setting as:
Flame Brightness (FL), Flame Color (FC)
Flame Brightness Setting
• Press “Flame” key until FL0 / FL1 / FL2 / FL3 / FL4 /
FL5 shown on the display, and then press “+” key or “-”
key to adjust the ame brightness from level 0 to level 5.
Flame Color Setting
• Press “Flame” key until FC1 / FC2 / FC3 / FC4 / FC5 /
FC6 shown on the display, and then press “+” key or “-”
key to adjust the ame color.
Timer Setting
• Timer can be adjusted when heater is ON. It can
adjusted from 0 hour (OFF) to 9 hours with 0.5 hour
interval.
• When TIMER is activated, the symbol will be displayed.
• When TIMER digital is 0 H, TIMER function is invalided.
The TIMER symbol will automatically disappear.
• When clock is at the setting mode, hold UP (“+”) and
DOWN (“-”) keys together to select 12H or 24H mode.
The unit default setting is 24H. The AM or PM symbol
will automatically displayed when the 12H mode was
selected.
• Press the timer key can exit the setting or it will
automatically exit after 8s without any further operation.
Clock Setting
• For clock setting, hold the TIMER key for 5s, hour
display will flashing. Push UP “+” or DOWN “-” key,
Hours setting can be adjusted. Touch the TIMER key
once more, minute display will ashing. Minutes setting
can be adjusted as the same way as hours setting.
Power Button
Each time the replace is plugged in, a 5-second fan and
heater will turn on for internal check program.
The unit has a memory function with last settings for
heating level and ame brightness effect, unless the main
power to the unit has been interrupted.
Flame Button
Heater Button
Timer Button
Setting Color
FC1
FC2
FC3
Yellow
Blue
Yellow + Red
Setting Color
FC4
FC5
FC6
Yellow + Blue + Red
Yellow + Blue
Color Rotation

14
FIREPLACE OPERATIONS
Care And Maintenance
NOTE: When the heater is not in use, it should be stored in a dry location, away from possible damage. The
power cord should be stored properly to avoid contact with hot or sharp objects.
REPLACING THE REMOTE CONTROL BATTERY:
When the remote control stops operating or its range seems reduced, it is time to replace the batteries.
NOTE: The batteries should be removed if the product is to be left unused for a long time.
CAUTION:
Non-rechargeable battery is not to be recharged. Exhausted battery is to be removed from the product:
1. The battery compartment is located on the back end of the remote control.
2. Remove battery cover from the back of remote control (E).
3. Insert 2pcs AAA batteries (not included), ensuring the polarities of the battery match the inside of the battery
compartment.
4. Re-insert the battery door.
WARNING: Make sure the power is turned off before proceeding. Any electrical repairs or rewiring of this unit
should be carried out by a licensed electrician in accordance with national and local codes.
If repairing or replacing an electrical component or wiring, the original wire routing, color coding and securing
locations must be followed.
WARNING: Electrical outlet wiring must comply with local building codes and other applicable regulations to
reduce the risk of re, electrical shock and injury to persons.
WARNING: Do not use this replace if any part of it has been under water. Immediately call a qualied service
technician to inspect the replace and replace any part of the electrical system.
WARNING: Disconnect the power before attempting any maintenance or cleaning to reduce the risk of re,
electrical shock or personal injury.
WARNING: During any service of this appliance, the power to the unit must be turned off. First turn the main
power switch to the "OFF" position. Then remove the electrical plug from the wall outlet.
CLEANING INFORMATION:
• Make sure the unit is turned off, unplugged and the heating elements of heater are cool whenever you are cleaning the
heater.
• Clean the metal trim using a water-dampened, soft, and clean cloth. DO NOT use brass polish or household cleaners as
these products will damage the metal trim.
• The motors used on the fan and the flame generator assembly are pre-lubricated for extended bearing life and
require no further lubrication. However, periodic cleaning/vacuuming of the fan/heater and air intake/output vents is
recommended.
Activate Child Lock
• When the unit is ON, hold the POWER button for 10
seconds to activate the Child Lock function. "E3" will be
displayed and a "beep" will sound 3 times to indicate the
Child Lock function is activated. Then, all function keys are
locked. When pressing any button, "E3" will be displayed
to indicate the Child Lock function has been activated.
Deactivate Child Lock
• To deactivate the Child Lock function, hold the POWER
button for 10 seconds. Then, all functions keys are
unlocked.
• Control the setting of flame brightness, flame color,
mood light brightness, mood light color, timer, clock and
temperture .
Child Lock
up Button ; Down Button
6. Power cord gets warm
4. Child Lock function is
1. Check that unit is plugged into a standard
120 volt outlet. Then make sure power is set
2. Unplug unit, wait 5-10 minutes, then the
sensor will reset itself. Plug the unit back
3. Unplug unit, wait 5-10 minutes, then the
sensor will reset itself. Plug the unit back
4. To inactivate the Child Lock function, hold
the POWER button for 10 seconds.
for an additional 20 seconds to ensure heat
requires more current to operate. Check the
outlet frequently to determine if it is HOT;
consult with a qualied electrician to check

15
FIREBOX OPERATIONS
Care And Maintenance
Troubleshooting
Problems
1. No power, logs do not
glow.
2. "E1" is displayed on
control panel.
3. "E2" is displayed on
control panel.
4. "E3" is displayed on
control panel.
5. Fan motor continues
to blow after unit is
powered off.
6. Power cord gets warm
to the touch.
1. The unit does not have
power.
2. The overheat protection
device has been
engaged.
3. The ambient temperature
sensor is broken or not
working correctly.
4. Child Lock function is
activated.
5. Normal operation.
6. Normal operation.
Possible Causes
1. Check that unit is plugged into a standard
120 volt outlet. Then make sure power is set
at "ON" position.
2. Unplug unit, wait 5-10 minutes, then the
sensor will reset itself. Plug the unit back
in and turn on the heater. If the problem
persists, call customer service.
3. Unplug unit, wait 5-10 minutes, then the
sensor will reset itself. Plug the unit back
in and turn on the heater. If the problem
persists, call customer service.
4. To inactivate the Child Lock function, hold
the POWER button for 10 seconds.
5. This is a standard feature; the blower runs
for an additional 20 seconds to ensure heat
will not be trapped inside the unit.
6. This is normal for a heater appliance as it
requires more current to operate. Check the
connections of the appliance cord and the
outlet. Make sure the plug fits tightly into
the outlet. During use, check the plug and
outlet frequently to determine if it is HOT;
if so, discontinue use of the appliance and
consult with a qualied electrician to check
or change the overheating outlet(s).
Solutions
For more information about collection and recycling of used batteries, please contact your local municipality, your waste
disposal service or the point of sale where you purchased this item.
A battery may contain hazardous substances that could be endangering to the environment
and human health.
• This symbol marked on the battery and/or packaging indicates that used battery shall not be
treated as municipal waste. Instead it shall be left at the appropriate collection point for recycling.
• By ensuring the used battery is disposed of correctly, you will help prevent potential negative
consequences for the environment and human health. The recycling of materials will help to
conserve natural resources.
DISPOSAL OF USED BATTERY:

QUESTIONS, PROBLEMS, OR MISSING PARTS?
Please Contact Customer Service Before Returning to Store
Crafted in China
Distributed by Soupro Limited Inc., 72 Montgomery Court, Markham, Ontario L3R 0C1
Ver.1
[email protected] [phone]
www.soupro.com

SP5736
Conservez ce manuel pour référence future
MANUEL D'UTILISATEUR
QUESTIONS, PROBLÈMES OU PIÈCES MANQUANTES?
Contactez le service clientèle avant de le retourner au magasin
Vériez soigneusement l'appareil et assurez-vous qu'il n'y a pas de dommages lorsque vous ouvrez le carton.
[email protected] [phone]
www.soupro.com

• GENERAL INFORMATION
Informations FCC / IC
Information de securite
Garantie
• INSTRUCTIONS D’ASSEMBLÉE
Préparation
Assemblée
• OPÉRATIONS DE FOYER
Instructions d’operation
Soins et entretien
Guide de depannage
Table des matières
2
INFORMATION DE SECURITE
N’utilisez cet appareil que pour l’usage prevu dans ce manuel. Toute autre utilisation n’est PAS recommandee par le fabricant
et peut provoquer un incendie, une decharge electrique ou des blessures.
MISE EN GARDE:
• Dans la mesure du possible, debranchez TOUJOURS cet appareil lorsqu’il n’est pas utilise.
• N’utilisez PAS un appareil muni d’une che ou d’un cordon endommages ou qui a subi une defaillance.
• Ne faites PAS fonctionner un appareil qui est tombe ou qui a ete endommage de quelque facon que ce soit. Coupez
l’alimentation electrique a partir du tableau de distribution et faites inspecter l’appareil par un electricien qualie avant de le
reutiliser.
• Conez toute reparation de ce foyer a un technicien qualie.
• Ne modiez jamais ce foyer. Replacez les pieces qui ont du etre retirees pour l’entretien avant d’utiliser de nouveau le foyer.
• N’utilisez PAS ce produit a l’exterieur.
• Cet appareil n’est pas concu pour etre utilise dans une salle de bains, une salle de lavage ou tout autre endroit humide
semblable. Ne placez JAMAIS l’article dans un endroit ou il pourrait tomber dans une baignoire ou un autre contenant rempli
d’eau.
• Pour debrancher cet appareil, tournez les commandes en position d’arret, puis retirez la che de la prise.
• Branchez UNIQUEMENT la che sur une prise correctement mise a la terre.
• Lors de l’installation, veillez a ce que l’appareil soit mis a la terre conformement aux codes locaux, a la plus recente version
du Code canadien de l’electricite, CSA C22.1, ou au code national de l’electricite, ANSI/NFPA No 70.
Cet article a été testé et déclaré conforme aux limites imposées aux dispositifs numériques de classe B, conformément à
l’alinéa 15 du règlement de la FCC. Ces limites sont destinées à assurer une protection raisonnable contre les interférences
nuisibles dans un environnement résidentiel. Cet article génère, utilise et peut émettre de l’énergie radiofréquence et, s’il n’est
pas installé et utilisé conformément aux instructions, risque de provoquer des interférences nuisibles lors de la réception
d’émissions de radio ou de télévision (il suft, pour le vérier, d’allumer et d’éteindre successivement l’article). L’utilisateur
devra prendre les mesures nécessaires suivantes pour tenter d’éliminer ces interférences:
(a) reorienter ou deplacer l’antenne receptrice;
(b) accroitre la distance entre l’appareil et le recepteur;
(c) brancher l’appareil sur une prise de courant appartenant a un autre circuit que celui du recepteur;
(d) obtenir de l’aide aupres du detaillant ou d’un technicien en radio ou en television experimente.
Cet appareil est conforme a l’alinea 15 du reglement de la FCC. Son utilisation est soumise aux deux conditions suivantes :
(a) cet appareil ne doit provoquer aucune interference nuisible; et
(b) cet appareil doit accepter toute interference recue, y compris des interferences susceptibles de causer un fonctionnement
non desire.
Les modifications non autorisees expressement par la partie reponsable de la conformite peuvent annuler le droit de
l’utilisateur de se servir de cet appareil.
Cet appareil numerique de classe B est conforme a la norme NMB-003 du Canada.
Informations FCC / IC
INFORMATIONS GÉNÉRALES
2
2
4
5
7
13
14
15

3
INFORMATIONS GÉNÉRALES
• An de prevenir les risques d’incendie, ne bloquez JAMAIS les ouvertures de ventilation ou de sortie d’air de quelque facon
que ce soit. Ne placez PAS l’appareil sur une surface molle, comme un lit, car l’ouverture pourrait se bloquer.
• Ne placez PAS l’appareil directement sous une prise de courant. Branchez TOUJOURS l’article directement sur une prise
murale. N’utilisez JAMAIS une rallonge ni une prise rechargeable (barre d’alimentation).
• A l’interieur de cet appareil se trouve un limiteur. Lorsque l’appareil surchauffe ou que sa temperature devient anormalement
elevee, le dispositif de protection du thermostat coupe l’alimentation electrique an d’eviter d’endommager l’appareil ou de
causer un incendie.
• Ne placez AUCUN objet sur le dessus du foyer encastrable et des prises d’air supérieures, car cela pourrait causer une
surchauffe de l’appareil et provoquer un incendie.
Branchement électrique
• Un circuit de 15 A, 120 V et 60 Hz avec une prise
correctement mise à la terre est nécessaire. Il est
recommandé de réserver un circuit au foyer, car d’autres
appareils alimentés par le même circuit pourraient causer
le déclenchement du disjoncteur ou faire sauter le fusible
lorsque le foyer est en fonction. L’appareil est muni d’un
cordon à trois broches d’une longueur de 1,83 m (6 pi) se
trouvant à l’arrière. Ne dépassez PAS le courant nominal
de la prise de courant. Branchez TOUJOURS l’article
directement sur une prise murale. N’utilisez JAMAIS de
rallonge ni de prise mobile (barre d’alimentation).
• Cet appareil est conçu pour être utilisé sur un circuit de
120 volts. La che dont est muni le cordon est illustrée
ci-dessous. Consultez l’illustration pour connaître les
instructions de mise à la terre. L’adaptateur illustré (C)
devrait être utilisé pour brancher les ches à trois broches
avec mise à la terre aux prises à deux fentes. La cosse de
mise à la terre verte de l’adaptateur doit être branchée sur
une mise à la terre permanente, comme une boîte de sortie
mise à la terre. Ne vous servez pas de l’adaptateur si une
prise à trois fentes avec mise à la terre est disponible.
AVIS IMPORTANT
Quand vous utilisez un appareil electrique, des precautions de base devrait etre toujours suivis pour reduire le
risque d’incendie, de choc electrique, de blessure corporel incluant les suivantes:
AVERTISSEMENT: Placez cette unité dans un endroit qui évite la lumière directe du soleil et des températures
élevées.
AVERTISSEMENT: Les sacs en plastique, les clous, etc. doivent être gardés hors de la portée des enfants.
AVERTISSEMENT: Cet appareil est chaud lors de l’utilisation. Pour éviter des brûlures, NE PAS laisser la peau
nue toucher les surfaces chaudes. Garder les matériaux combustibles comme les meubles, oreillers, draps,
papiers, vêtements et rideaux à moins de 3 pieds du devant de l’appareil et les tenir à l’écart des côtés et de l’arrière.
AVERTISSEMENT: Des precautions extremes sont necessaire lorsque l’appareil est utilise par ou pres
d’enfants ou de personnes avec un handicap et lorsque le foyer est laisse sans surveillance.
AVERTISSEMENT: NE PAS utiliser une rallonge sous un tapis. NE PAS couvrir le ls d’alimentation avec une
carpette ou tout autre objet du genre. Placer le ls d’alimentation en dehors d’emplacement ou il y a de la
circulation.
AVERTISSEMENT: NE PAS inserer ou laisser des objets etrangers entrer dans les fentes de ventilation ou sortie
d’air. Ceci peut causer un choc electrique, un incendie ou des dommages a l’appareil.
AVERTISSEMENT: Cet appareil contient des pièces chaudes et qui cause des arc électrique à l’intérieur. NE
PAS utiliser dans une pièce où de l’essence, peinture, liquide inammable sont utilisés ou entreposés. Cet
appareil ne doit pas être utilisé comme sèche linge. Les bas de Noel ou les décorations ne devraient pas être
accroché près du foyer.
Assurez-vous de lire et de comprendre l’integralite du present manuel avant de tenter d’assembler, d’installer ou d’utiliser
l’article.
CARACTERISTIQUES
Tension:
Amperes:
Watts:
120 VAC, 60 Hz
11.7 Amps
1400 Watts
Broche de
mise a la terre
Broche de mise
a la terre
Dispositif de mise
a la terre
Adaptateur
A
C
B
D
Vis en
metal
Couvercle
de la boite
de mise
a la terre

GARANTIE
1 AN GARANTIE LIMITEE
Soupro Limited Inc. (ci-apres refere comme la (compagnie) garantie que votre nouveau foyer electrique KOMODO est libre
de tous defauts de fabrication pour une periode de un an de la date d’achat. Sujet aux conditions et limitations suivantes.
1. Le foyer electrique doit etre installe et utilise en accord avec le manuel d’installation et d’utilisation
fournis avec l’appareil. Toute reparation non autorisee, modication, abus volontaire, accident, mauvaise
utilisation du produit annulera la garantie.
2. Cette garantie est non transferable et est pour le proprietaire original qui a achete le produit d’un
fournisseur autorise de la compagnie.
3. La garantie est limitee a la reparation ou le remplacement des pieces defectueuses a condition que ces
pieces ont ete utilisees de facon normale, apres que les dites pieces ont ete conrme defectueuses par
l’inspection de la compagnie.
4. La Compagnie, a sa discretion, exiger que toutes les pièces défectueuses soient retournées en échange
de la (les) pièce (s) de rechange.
5. La Compagnie, a sa discretion, peut se decharger de toutes ses obligations a l'egard de cette garantie en
remboursant le prix d’achat des pieces defectueuses.
6. Cette garantie ne couvre pas les lumieres DEL incluses avec les foyers electriques.
7. Toute installation, main-d'oeuvre pour la construction, le transport, ou d'autres frais et / ou depenses
decoulant de la piece defectueuse, de la reparation, du remplacement, ne sera pas couvert par cette
garantie et la Compagnie n’en assume pas la responsabilite.
8. Le propriétaire / utilisateur assume tous les autres risques. Y compris le risque de perte ou de dommages
directs, indirects ou consécutifs découlant de l'utilisation. Ou l'impossibilité d'utiliser le produit, sauf dans
les cas prévus par la loi.
9. Toutes les autres garanties en ce qui concerne le produit, ses composants et accessoires, ou des
obligations / responsabilites de la part de la Compagnie sont expressement exclues.
10. La Compagnie n'assume, ni autorise un tiers à assumer, à ce nom, toute autre responsabilité à l'égard de
la vente du produit.
11. Les garanties decrites dans le present document ne sont pas applicables aux accessoires non utilises en
conjonction avec l'installation de ce produit.
12. Cette garantie vous donne des droits speciques, et vous pouvez egalement avoir d'autres droits qui
varient d'un Etat a l'autre.
Cette garantie est nulle si:
(a) Le foyer est soumis a des periodes prolongees d'humidite ou de la condensation.
(b) Toute modication non autorisée, abus volontaire, accident ou mauvais usage du produit.
(c) Vous n’avez pas le recu d’achat original.
SI LE SERVICE DE GARANTIE EST NÉCESSAIRE
Contactez le service à la clientèle
Assurez-vous que vous disposez des informations suivantes:
• Garantie
• Facture de vente
• Modèle de produit / numéro de série
• Date d'achat
• Emplacement de l'achat
[email protected] [phone]
www.soupro.com
4
INFORMATIONS GÉNÉRALES