KONDATOR LA-911 User manual

LGD Monitor Arm
LA-911.LA-921.
LA-912.LA-922 <<<
Loading:
LA-911.LA-921 : 4~9kg (8.8~19.8 Ibs)
LA-912.LA-922 : 8~15kg (17.6~33 Ibs)
LA-911. LA-912
*Clamp” assembly step
Adhere the pad to the clamp base.
Desk thickness from 20mm~50mm.
Then fix the clamp on the desk.
LA-921.LA-922
*Grommet” assembly step(1-1)
Use 2mm allen key to lose
screw, Then take out the arm up.
Notice:
Don’t make the screw drop.
fod -Yod Gem IE}:
Before assembly please spend some time to read this and follow the procedures step
by step. Some panels are viewed differently from the detail drawing below. This is for
extra clarity.Do not discard any of the packaging until you have checked all the parts
and the package of fittings. If you miss any of the parts, please contact the store
where you purchased your products. The staff will do their best to help you .
LA-911.LA-912 >20
Part Check-List
Fitting / Tools
Check-List
LA-921.LA-922
))
)
Fitting
/
Tools
Check-List
Part Check-List
Assembl
LA-921.LA-922
*"Grommet” assembly step(1-2)
To assemble the small metal plate on
the bottom concavity of the grommet
set then adhere the pad to the
grommet set which is touch with desk
surface. Then fix the grommet set on
the desk through a bolt and parts (as
figures below).Desk thickness from
20mm~50mm.The diameter of the
hole is from 20mm to 50mm.
LA-921.LA-922
*Grommet” assembly step(1-3)
Fix the grommet mount on the
desk. Use 2mm allen key to
secure the pole and the
grommet mount with the screw
to the bottom, and than move
backward 1 circle.
Note:
Before secure the
screw please make
sure a concavity
which on the bottom
of the arm if aim at the
small hole position
together.

Assembl
Move the knob out first then pull it down to open the VESA adapter Insert the VESA adapter
plate switch then take it up form the arm. plate(with LCD display on
already)into the arm and press
it down.Then push the knob
up.(as figure)
eThese screws (M4/15L)
Place LCD with facing ener one ie al (1 )Use cable tie supplied to (2)Move the cable cover up
downward on flat surface. serews aré toosh finish cable management. then to open it for finish cable
Place VESA adapter plate fasten. management.
on the LCD back as figure ;
and align to the screw
holes.
Secure them together with
four screws .And then
tighten them up with
screwdriver(not provided).
75mmx75mm
100mmx100mm
VESA interface.
Cable tie
Adjustment For Loading Adjusting Universal Joint Tension
When assembling the arm with monitors of differing weights, you may find
that the tension of the universal joint needs to be adjusted to ease movement or
2.Support arm with a hand during assembly. to maintain the desired monitor position. If so, adjust as follows:
Caution for weight capacity adjustment:
1.Make sure of the LCD panel weight.
Adjustment:
Use the Allen key provided to adjust the weight capacity.
Twist the Allen key in a clockwise direction for less weight;
counterclockwise direction for more weight.
e LA-911. LA-921: 4~9 kg ( 8.8~19.8 Ibs)
è LA-912. LA-922: 8~15 kg ( 17.6~33 Ibs)
Screw Head
. Remove the plastic universal joint cover.
. Find the nylon nut (not the screw head) and use the included
wrench to adjust the tension.
. Use one hand to support the monitor and adjust the tension
Of the universal joint.
eClockwise : more tension
eCounterclockwise : less tension
d. When the desired tension is achieved, replace the plastic cover.
Caution:
eSupport the monitor during the adjustment procedure.
eOnly adjust the nylon nut (not the screw head).
eDo not disassemble the universal joint .