Konig & Meyer 19794 User manual

SETUP (6-13)
19794 Tablet PC wall mount
- For tablets of all manufacturers - not bound to a specific brand
- Screen sizes (Width: 222 - 332 mm, Height: 128 - 234 mm, Depth: 6-11 mm)
- Helpful settings for quick setup and adjustment of the support arms
- Set it once and it stays in place until you choose to switch out the tablet.
- Easy to attach and detach thanks to the practical snap lock.
- The tablet can switch between portrait and landscape positions.
- Easy access to the connectors.
- With 3 drill holes to securely fasten it to the wall.
SAFETY NOTES
Thank you for choosing this product. This instruction manual informs you about the
important steps to set up and handle the product. We recommend to keep the manual
in a separate place for a possible later use.
When mounting the Tablet PC be sure to follow the instructions that come with
the mount and check that the Tablet is securely fastened. K&M is not liable for
improper use or any consequential damages!
- The holder is affixed to the wall with three screws.
-NOTE:
-a. Walls that are too weak or have electrical and water conduits or similar
-a.are not suitable. If this is the case consult a qualified handyman.
-b. Depending on the wall composition (Wood, Concrete, Bricks etc.) use
-b.the appropriate mounting materials (not included in the delivery).
-c. Ensure that the screws and nuts are tight after the product has been
-c.installed and check that the screws are tight on a routine basis.
- Carefully position and place the Tablet PC using the clamp screws,
-then check that the Tablet PC is securely in place
- Use the mount carefully; especially when switching from portrait to
-landscape and adjusting the angle
FIRST TIME PLACEMENT of the Tablet (6-13) * Scale settings are only examples (Selection: see INFO SHEET)
FIRST TIME PLACEMENT of the Tablet
6First open the three knurled pins until
6there is enough depth to place the tablet
7a. Release the upper support arm,
7b. extend it out as far as it goes and
7c. tighten the clamping screw
8a. Release side support arms and...
8b. ...with the help of the scale symmetrically
8b. extend to a rough position
8c. Tighten both clamping screws
9Place the tablet into the corner supports
9to ensure that it fits
9a. Tablet is too narrow: Retract the support
9a. arms a bit (symmetrically) until it fits.
9b. Tablet is too wide: Extend the support
9b. arms (symmetrically) until it fits.
9c. Tablet fits, if the corner supports do not
9c. show any space between the tablet and
9c. the holder when looking at it from the side.
10 a. Place the tablet in both corner supports...
10 b. ...and hold the tablet
11 Retract the upper support arm
11 a. Release the clamp screw and retract
11 a. the support arm...
11 b. ...until the tablet is securely held in place.
11 c. Tighten the clamping screw
WALL MOUNT (1-5)
The wall mount comes pre-assembled
and can be mounted to the wall right away.
1.a Hold the wall mount and turn the round
1.a wall plate clockwise - as far as it will go.
1.b Place the mount at the desired position
1.b on the wall in a horizontal position...
2...and mark the three drill holes with a marker
3Drill the anchor holes
3- ø 6 mm for plastic anchors
3- if needed ø 3 mm for wood screws
4Mounting example concrete wall
5Mounting example wood wall
If the wall is made of aerated concrete,
plaster board etc. we recommend that
you purchase suitable anchors.
fits fits fits
Tab too narrow Tab too wide Tab fits
Mounting Examples (4-5)
WALL MOUNT Positioning (1-3)
WoodStone, concrete

KÖNIG & MEYER GmbH & Co. KG
Kiesweg 2, 97877 Wertheim, www.k-m.de
19794-000-55 Rev.05 03-80-085-00 1/18
TECHNISCHE DATEN
Material Holder, joint: Polyamid PA-6
Screws: Steel, galvanized
max. load
Tablets Height: min. 222 mm, max. 334 mm
Tablets Width: min. 128 mm, max. 232 mm
Tablets Depth: min. 6 mm, max. 11 mm
Packagin W x D x H: 232 x 55 x 154 mm
Weight 0.204 kg
USAGE NOTES and
FUNCTIONS (14-20)
FAULT-FINDING (F) and REPAIR (R)
F: Holder is unstable
F: B: Check the wall screws
F: B: Check the connection between the wall plate and holder plate
F: Tablet is not securely in place
F: B: Correct the position of the side support ams, so that the corner supports
F: B: are properly set on the Tablet without any play (7-9)
F: B: Ensure that the lower support arms setting are symmetrical (8,9)
F: B: Asymmetric support arm settings looks bad and does not ensure that
F: B: the Tablet is securely in place.
F: B: Do not only place the Tablet on the upper support arm, but be sure it
F: B: clicks into place (11,12,20).
F: B: Observe the minimum i.e maximum dimensions (14)
FIRST TIME PLACEMENT of the Tablet (6-13)
DIMENSIONS (14) REMOVING the Tablet (15-17)
REPEATED PLACEMENT of the Tablet (18-20) + (13.a.b.c)
Final Position
- landscape
- clicked into place
Final Position
- portrait
- clicked into place
Twist (Interim Position):
- In between landscape and portrait
- not clicked into place, however
-it does stay in the selected position
DIMENSIONS (14)
If the tablet’s dimensions are too large or too
small (atypical) for the mount it will not fit.
REMOVING the Tablet (15-17)
15 Loosen the knurled pins a bit
16 Hold the tablet and LIFT UP
16 the catch
17 Flip out the Tablet and REMOVE
If you always use the same Tablet PC
we recommend leaving the support
arm settings in this set position.
REPEATED PLACEMENT of the
Tablet (18-20)
for previously set support arms
18 Place the tablet in the lower corner
18 supports
19 Place the tablet into the upper catch and
19 gently press until it clicks into place
20 Tighten the knurled pins until the tablet
20 is gently pressed into place
Check to ensure that the Tablet PC is secure
13.a.b.c.
FORMAT (21)
The mount and the Tablet can be turned 90°.
Do accomplish this the Tablet does not need to
be removed from the holder.
21 Take the holder and turn it to the
21 landscape, portrait,
21 - or tilted position!
21 NOTE:
21 Invisible stops on the holder limit how
21 far the holder can be turned.
SETUP (6-13)
12 Gently clamp the tablet in the corner
12 supports by tightening the knurled pins
13 Your Tablet should be securely positioned.
13 Please check that the following
13 is the case:
13 a. Is the Tablet securely mounted?
13 b. Are the three knurled handles
13 b. properly tightened?
13 c. Are the three plastic finger screws
13 c. properly tightened?
If not please take corrective action (6-11).
FORMAT (21)

19794
Tablet PC wall mount
Product variant
19794-000-55 - black
Data
Depth from 0.236 to 0.433"
Height from 8.74 to 13.15"
Material plastic
Max. load capacity 1.652 lbs
Mounting attaches to walls
Special features freely rotates 90°
Swivel 90 º
Type black
Wall clearance 1.772 "
Weight 0.474 lbs
Width from 5.039 to 9.134"
The universal tablet PC wall mount fits different tablet sizes. The individually adjustable support arms can accommodate the use
of tablets ranging in height from 8.74 to 13.149" and a width from 5.039 to 9.133" (such as e.g. iPad, iPad Air, iPad Pro, Amazon
Fire HDX 8.9, Samsung Galaxy Tab ab 9.7, Google Nexus 9, Asus Transformer or Microsoft Surface and Surface Pro). The depth of the
tablets can vary between 0.236 and 0.433". Before the first use of the tablet holder the three support arms are adjusted by the
clamp screws to the exact size and depth of the tablet. For other uses the tablet can be attached and detached quickly and simply
using a snap lock. The tablet can switch between portrait and landscape positions. The tablet is kept in place, there is no risk
of the tablet switching positions by itself. The wall mount is easy to mount to the wall using the three drill holes.