KoolMore KM-MD-1SS User manual
ANTI-TIP BLOCK
NORMAL INSTALLATION STEPS
ANTI-TIP BLOCK INSTALLATION INSTRUCTIONS
7RUHGXFHWKHULVNRIWLSSLQJRIWKHGUDZHUWKH$QWL7LS
EORFNPXVWEHSURSHUO\LQVWDOOHGORFDWHG
LQFKHVDERYHWKHIORRURQZKLFKWKH0LFURZDYH
'UDZHUZLOOVLW7KHLQFK$QWL7LSEORFNPXVWEH
SURYLGHGE\WKHLQVWDOOHU6HH)LJXUHVDQG7KH
$QWL7LSEORFNSUHYHQWVVHULRXVLQMXU\WKDWPLJKWUHVXOW
IURPVSLOOHGKRWOLTXLGV
,IWKH0LFURZDYH'UDZHULVHYHUPRYHGWRDGLIIHUHQW
ORFDWLRQWKH$QWL7LSEORFNPXVWDOVREHPRYHGDQG
LQVWDOOHG:KHQLQVWDOOHGWRWKHZDOOPDNHVXUHWKDW
WKHVFUHZVFRPSOHWHO\SHQHWUDWHWKHGU\ZDOODQGDUH
VHFXUHGLQZRRGRUPHWDOVRWKDWWKHEORFNLVWRWDOO\
VWDEOH:KHQIDVWHQLQJEHVXUHWKDWWKHVFUHZVGRQRW
SHQHWUDWHHOHFWULFDOZLULQJRUSOXPELQJ
ELECTRICAL OUTLET
7KHHOHFWULFDOUHTXLUHPHQWVDUHDYROW+]$&
RQO\ODPSRUPRUHSURWHFWHGHOHFWULFDOVXSSO\,WLV
UHFRPPHQGHGWKDWDVHSDUDWHFLUFXLWVHUYLQJRQO\WKLV
DSSOLDQFHEHSURYLGHG
7KHGUDZHULVHTXLSSHGZLWKDSURQJJURXQGLQJSOXJ
,WPXVWEHSOXJJHGLQWRDZDOOUHFHSWDFOHWKDWLV
SURSHUO\LQVWDOOHGDQGJURXQGHG6KRXOG\RXRQO\
KDYHSURQJRXWOHWKDYHDTXDOLILHGHOHFWULFLDQLQVWDOO
DFRUUHFWZDOOUHFHSWDFOH
Note,I\RXKDYHDQ\TXHVWLRQVDERXWWKHJURXQGLQJ
RUHOHFWULFDO
,QVWUXFWLRQVFRQVXOWDTXDOLILHGHOHFWULFLDQRUVHUYLFH
SHUVRQ
&DQDOVREHLQVWDOOHGXVLQJDQHOHFWULFDORXWOHWLQ
DQDGMDFHQWFDELQHWZLWKLQWKHDUHDZKHUHWKH
SURYLGHGHOHFWULFDOFRUGFDQUHDFK
$OZD\VFKHFNHOHFWULFDOFRGHVIRUUHTXLUHPHQWV
GROUNDING INSTRUCTIONS
7KLVDSSOLDQFHPXVWEHJURXQGHG7KH0LFURZDYH
'UDZHULVHTXLSSHGZLWKDFRUGKDYLQJDJURXQGLQJ
ZLUHZLWKDJURXQGLQJSOXJ,WPXVWEHSOXJJHGLQWRD
ZDOOUHFHSWDFOHWKDWLVSURSHUO\LQVWDOOHGDQGJURXQGHG
LQDFFRUGDQFHZLWKWKH1DWLRQDO(OHFWULFDO&RGHDQG
ORFDOFRGHVDQGRUGLQDQFHV,QWKHHYHQWRIDQ
HOHFWULFDOVKRUWFLUFXLWJURXQGLQJUHGXFHVULVNRI
HOHFWULFVKRFNE\SURYLGLQJDQHVFDSHZLUHIRUWKH
HOHFWULFFXUUHQW
WARNING _,PSURSHUXVHRIWKHJURXQGLQJSOXJFDQ
UHVXOWLQDULVNRIHOHFWULFVKRFNDo not use an
extension cord .If the power supply cord is too
short ,have a qualified electrician or serviceman
install an outlet near the appliance.
S
u
gg
e
st
e
del
e
ct
r
ic
a
l
ou
t
le
tlo
c
at
i
on
5
''
4
'
'
Anti Tip
block
(6'')
3
12
''
)LJXUH )LJXUH
3
INSTALLATION MANUAL
MICROWAVE DRAWER
Model: KM-MD-1SS
KoolMore Built-in Stainless Steel
Microwave Drawer
Stay informed with the latest information
for your KoolMore Appliance.
If you need any assistance or have questions, our customer
support team is here to help.
SPECIAL WARNING
INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.
IMPORTANT: SAVE this installation manual FOR LOCAL ELECTRICAL INSPECTOR'S USE.
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CLEARANCES AND DIMENSIONS
For SAFETY CONSIDERATIONS do not install drawer in any combustible cabinetry, which is not in
accord with the stated clearances and dimensions on pages 2 and 3. See Figure 1.
UNPACKING YOUR MICROWAVE DRAWER
Remove all packing materials from inside the Microwave Drawer.DO NOT REMOVE THE WAVEGUIDE
COVER, which is located on the top of the Microwave Drawer.
Remove the feature sticker, if there is one. Check the drawer for any damage, such as misaligned or
bent drawer, damaged drawer seals and sealing surfaces, broken or loose Microwave Drawer guides
and dents inside the cavity or on the front side of the drawer. If there is any damage, do not operate
the Microwave Drawer and contact your dealer or a MIDEA AUTHORIZED SERVICER.
IMPORTANT NOTES TO THE INSTALLER
Read all of the Installation Manual before installing the Microwave Drawer.
Remove all packing material before connecting the electrical supply.
Observe all governing codes and ordinances.
Be sure to leave these instructions with the consumer.
IMPORTANT NOTES TO THE CONSUMER
Keep this manual with your Operation Manual for future reference.
As when using any microwave oven generating heat, there are certain safety precautions you should
follow. These are listed in the Operation Manual. Read all and follow carefully.
Be sure your Microwave Drawer is installed and grounded properly by a qualified installer or service
technician.
WARNING if the information in this manual is not followed exactly, a fire or electrical shock may result
that could cause property damage, personal injury or death.
WARNING To reduce the risk of tipping, the Microwave Drawer must be secured by a
properly installed Anti-Tip block.
This Microwave Drawer must be electrically grounded in accordance with local codes.
Make sure the wall coverings and the cabinets around the Microwave Drawer can
withstand the heat generated by the Microwave Drawer.
WARNING Never leave children alone or unattended in the area where a Microwave
Drawer is in use. Never leave the drawer open when the microwave is unattended.
WARNING Stepping, leaning or sitting on the drawer may result in serious injuries and
can also cause damage to the Microwave Drawer.
Do not use the Microwave Drawer as a storage space. This creates a potentially
hazardous situation.
Check that the time-of-day is in the display. If not, touch Stop/Clear to prevent
unintended use.
SPECIAL WARNING
INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.
IMPORTANT: SAVE this installation manual FOR LOCAL ELECTRICAL INSPECTOR'S USE.
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CLEARANCES AND DIMENSIONS
For SAFETY CONSIDERATIONS do not install drawer in any combustible cabinetry, which is not in
accord with the stated clearances and dimensions on pages 2 and 3. See Figure 1.
UNPACKING YOUR MICROWAVE DRAWER
Remove all packing materials from inside the Microwave Drawer.DO NOT REMOVE THE WAVEGUIDE
COVER, which is located on the top of the Microwave Drawer.
Remove the feature sticker, if there is one. Check the drawer for any damage, such as misaligned or
bent drawer, damaged drawer seals and sealing surfaces, broken or loose Microwave Drawer guides
and dents inside the cavity or on the front side of the drawer. If there is any damage, do not operate
the Microwave Drawer and contact your dealer or a MIDEA AUTHORIZED SERVICER.
IMPORTANT NOTES TO THE INSTALLER
Read all of the Installation Manual before installing the Microwave Drawer.
Remove all packing material before connecting the electrical supply.
Observe all governing codes and ordinances.
Be sure to leave these instructions with the consumer.
IMPORTANT NOTES TO THE CONSUMER
Keep this manual with your Operation Manual for future reference.
As when using any microwave oven generating heat, there are certain safety precautions you should
follow. These are listed in the Operation Manual. Read all and follow carefully.
Be sure your Microwave Drawer is installed and grounded properly by a qualified installer or service
technician.
WARNING if the information in this manual is not followed exactly, a fire or electrical shock may result
that could cause property damage, personal injury or death.
WARNING To reduce the risk of tipping, the Microwave Drawer must be secured by a
properly installed Anti-Tip block.
This Microwave Drawer must be electrically grounded in accordance with local codes.
Make sure the wall coverings and the cabinets around the Microwave Drawer can
withstand the heat generated by the Microwave Drawer.
WARNING Never leave children alone or unattended in the area where a Microwave
Drawer is in use. Never leave the drawer open when the microwave is unattended.
WARNING Stepping, leaning or sitting on the drawer may result in serious injuries and
can also cause damage to the Microwave Drawer.
Do not use the Microwave Drawer as a storage space. This creates a potentially
hazardous situation.
Check that the time-of-day is in the display. If not, touch Stop/Clear to prevent
unintended use.
CLEARANCES AND DIMENSIONS
·'LPHQVLRQVWKDWDUHVKRZQLQ)LJXUHPXVWEH
XVHG*LYHQGLPHQVLRQVSURYLGHPLQLPXP
FOHDUDQFH/RFDWHHOHFWULFDORXWOHWLQWKHVKDGHG
DUHDLQWKHXSSHUOHIWKDQGFRUQHURIWKHFXWRXW
6HH)LJXUH
·&RQWDFWVXUIDFHPXVWEHVROLGDQGOHYHO3D\
VSHFLDODWWHQWLRQWRWKHIORRURQZKLFKWKH
0LFURZDYH'UDZHUZLOOVLW7KHIORRURIWKHRSHQLQJ
VKRXOGEHFRQVWUXFWHGRISO\ZRRGVWURQJHQRXJK
WRVXSSRUWWKHZHLJKWRIWKHRYHQDERXW
SRXQGV
·&KHFNORFDWLRQZKHUHWKH0LFURZDYH'UDZHUZLOO
EHLQVWDOOHGIRUSURSHUHOHFWULFDOVXSSO\
·<RXURYHQFDQEHEXLOWLQWRDFDELQHWRUZDOOE\
LWVHOIRUXQGHUDJDVRUHOHFWULFZDOORYHQ
·%HVXUHWKDWWKHFOHDUDQFHRIWKHIORRUEHWZHHQ
WKHZDOORYHQDQGWKHPLFURZDYHGUDZHULVD
PLQLPXPRILQFKHV
·7KHPLFURZDYHLQWHULRUZLOOHDVLO\DFFRPPRGDWHD
[REORQJGLVKRUDEDJRIPLFURZDYH
SRSFRUQ
MICROWAVE DRAWER MEASUREMENTS
)LJXUHVDQGFRQWDLQPDQ\0LFURZDYH'UDZHU
PHDVXUHPHQWVIRUUHIHUHQFHZKHQSODQQLQJWKH
GUDZHUVORFDWLRQ7KLV0LFURZDYH'UDZHUFDQEH
LQVWDOOHGEHORZDQ\HOHFWULFRUJDVZDOORYHQ
&DQDOVREHLQVWDOOHGXVLQJDQHOHFWULFDORXWOHWLQDQ
DGMDFHQWFDELQHWZLWKLQWKHDUHDZKHUHWLUHSURYLGHG
HOHFWULFDOFRUGFDQUHDFK3RZHUFRUGDFFHVVKROHLQ
FDELQHWVKRXOGEHDPLQLPXPOGLDPHWHUKROHDQG
GHEDUUHGRIDOOVKDUSHGJHV
IMPORTANT $OZD\VDOORZVXIILFLHQWSRZHUFRUG
OHQJWKWRWKHHOHFWULFDORXWOHWWRSUHYHQWWHQVLRQ$OZD\V
FKHFNHOHFWULFDOFRGHVIRUUHTXLUHPHQWV
Anti Tip
block
Floot must
support 100lbs
Suggested electrical
outlet location
24''
cabinet min
36''
countertop
height
5''
4''
2
3
12
''
mindepth
22
18
'
opening
Allow
7
8
''
overlap
Al
low
716
''
overl
ap
19''to
top
of
floor
14
1316
''
opening
14
1316
''
tobottomof
Anti-tipblock
(6'')
3
1
2
'
'
Allow316''
overlap
Allow78''
overlap
2
1
9
16
''
23
78
''
15''
2
78
'
'
1
1
1
16
''
doo
r
th
i
c
kn
es
s
14
1932
''
1
5
''
auto
dra
wer
o
pen
in
g
)LJXUH
)LJXUH
2
NORMAL INSTALLATION STEPS
ANTI-TIP BLOCK INSTALLATION INSTRUCTIONS
To mitigate tipping risk, the Anti-Tip block must be properly installed below the microwave drawer,
precisely 13/16 inches above the floor.
The 6-inch Anti-Tip block, provided by the installer, must be located as per Figures 1 and 3 to prevent
injury from spills.
If relocating the Microwave Drawer, the Anti-Tip block must also be repositioned.
Ensure the block is fastened to the wall with screws fully penetrating the dry wall and secured in wood
or metal for stability.
Caution: Avoid screwing into electrical wiring or plumbing.
GROUNDING INSTRUCTIONS
The Microwave Drawer must be grounded and comes with a cord having a grounding wire and plug.
It must be connected to a properly installed and grounded wall receptacle, following the National Elec-
trical Code and local standards, to minimize electrical short circuit risk and reduce electric shock haz-
ards.
ELECTRICAL REQUIREMENTS
Requires a dedicated 120-volt 60 Hz, AC only, 15 amp or greater electrical supply.
It should be served by a dedicated circuit.
The drawer comes with a 3-prong grounding plug and must be plugged into an appropriately grounded
receptacle.
If there's only a 2-prong outlet, a correct wall receptacle installation by a qualified electrician is neces-
sary.
Note: For grounding or electrical concerns, consulting a qualified electrician or service person is recom-
mended.
The appliance can also be powered from an adjacent cabinet if the electrical cord can reach and the
electrical outlet is installed as per codes.
WARNING
Improper use of the grounding plug can lead to electric shock hazards.
ANTI-TIP BLOCK
NORMAL INSTALLATION STEPS
ANTI-TIP BLOCK INSTALLATION INSTRUCTIONS
7RUHGXFHWKHULVNRIWLSSLQJRIWKHGUDZHUWKH$QWL7LS
EORFNPXVWEHSURSHUO\LQVWDOOHGORFDWHG
LQFKHVDERYHWKHIORRURQZKLFKWKH0LFURZDYH
'UDZHUZLOOVLW7KHLQFK$QWL7LSEORFNPXVWEH
SURYLGHGE\WKHLQVWDOOHU6HH)LJXUHVDQG7KH
$QWL7LSEORFNSUHYHQWVVHULRXVLQMXU\WKDWPLJKWUHVXOW
IURPVSLOOHGKRWOLTXLGV
,IWKH0LFURZDYH'UDZHULVHYHUPRYHGWRDGLIIHUHQW
ORFDWLRQWKH$QWL7LSEORFNPXVWDOVREHPRYHGDQG
LQVWDOOHG:KHQLQVWDOOHGWRWKHZDOOPDNHVXUHWKDW
WKHVFUHZVFRPSOHWHO\SHQHWUDWHWKHGU\ZDOODQGDUH
VHFXUHGLQZRRGRUPHWDOVRWKDWWKHEORFNLVWRWDOO\
VWDEOH:KHQIDVWHQLQJEHVXUHWKDWWKHVFUHZVGRQRW
SHQHWUDWHHOHFWULFDOZLULQJRUSOXPELQJ
ELECTRICAL OUTLET
7KHHOHFWULFDOUHTXLUHPHQWVDUHDYROW+]$&
RQO\ODPSRUPRUHSURWHFWHGHOHFWULFDOVXSSO\,WLV
UHFRPPHQGHGWKDWDVHSDUDWHFLUFXLWVHUYLQJRQO\WKLV
DSSOLDQFHEHSURYLGHG
7KHGUDZHULVHTXLSSHGZLWKDSURQJJURXQGLQJSOXJ
,WPXVWEHSOXJJHGLQWRDZDOOUHFHSWDFOHWKDWLV
SURSHUO\LQVWDOOHGDQGJURXQGHG6KRXOG\RXRQO\
KDYHSURQJRXWOHWKDYHDTXDOLILHGHOHFWULFLDQLQVWDOO
DFRUUHFWZDOOUHFHSWDFOH
Note,I\RXKDYHDQ\TXHVWLRQVDERXWWKHJURXQGLQJ
RUHOHFWULFDO
,QVWUXFWLRQVFRQVXOWDTXDOLILHGHOHFWULFLDQRUVHUYLFH
SHUVRQ
&DQDOVREHLQVWDOOHGXVLQJDQHOHFWULFDORXWOHWLQ
DQDGMDFHQWFDELQHWZLWKLQWKHDUHDZKHUHWKH
SURYLGHGHOHFWULFDOFRUGFDQUHDFK
$OZD\VFKHFNHOHFWULFDOFRGHVIRUUHTXLUHPHQWV
GROUNDING INSTRUCTIONS
7KLVDSSOLDQFHPXVWEHJURXQGHG7KH0LFURZDYH
'UDZHULVHTXLSSHGZLWKDFRUGKDYLQJDJURXQGLQJ
ZLUHZLWKDJURXQGLQJSOXJ,WPXVWEHSOXJJHGLQWRD
ZDOOUHFHSWDFOHWKDWLVSURSHUO\LQVWDOOHGDQGJURXQGHG
LQDFFRUGDQFHZLWKWKH1DWLRQDO(OHFWULFDO&RGHDQG
ORFDOFRGHVDQGRUGLQDQFHV,QWKHHYHQWRIDQ
HOHFWULFDOVKRUWFLUFXLWJURXQGLQJUHGXFHVULVNRI
HOHFWULFVKRFNE\SURYLGLQJDQHVFDSHZLUHIRUWKH
HOHFWULFFXUUHQW
WARNING _,PSURSHUXVHRIWKHJURXQGLQJSOXJFDQ
UHVXOWLQDULVNRIHOHFWULFVKRFNDo not use an
extension cord .If the power supply cord is too
short ,have a qualified electrician or serviceman
install an outlet near the appliance.
S
u
gg
e
st
e
del
e
ct
r
ic
a
l
ou
t
le
tlo
c
at
i
on
5
''
4
'
'
Anti Tip
block
(6'')
3
12
''
)LJXUH )LJXUH
3
Do not use an extension cord. If the power supply cord is too short, an outlet should be installed near
the appliance by a qualified technician.
NORMAL INSTALLATION STEPS
ANTI-TIP BLOCK INSTALLATION INSTRUCTIONS
To mitigate tipping risk, the Anti-Tip block must be properly installed below the microwave drawer,
precisely 13/16 inches above the floor.
The 6-inch Anti-Tip block, provided by the installer, must be located as per Figures 1 and 3 to prevent
injury from spills.
If relocating the Microwave Drawer, the Anti-Tip block must also be repositioned.
Ensure the block is fastened to the wall with screws fully penetrating the dry wall and secured in wood
or metal for stability.
Caution: Avoid screwing into electrical wiring or plumbing.
GROUNDING INSTRUCTIONS
The Microwave Drawer must be grounded and comes with a cord having a grounding wire and plug.
It must be connected to a properly installed and grounded wall receptacle, following the National Elec-
trical Code and local standards, to minimize electrical short circuit risk and reduce electric shock haz-
ards.
ELECTRICAL REQUIREMENTS
Requires a dedicated 120-volt 60 Hz, AC only, 15 amp or greater electrical supply.
It should be served by a dedicated circuit.
The drawer comes with a 3-prong grounding plug and must be plugged into an appropriately grounded
receptacle.
If there's only a 2-prong outlet, a correct wall receptacle installation by a qualified electrician is neces-
sary.
Note: For grounding or electrical concerns, consulting a qualified electrician or service person is recom-
mended.
The appliance can also be powered from an adjacent cabinet if the electrical cord can reach and the
electrical outlet is installed as per codes.
WARNING
Improper use of the grounding plug can lead to electric shock hazards.
Installation Instructions:
1. Position the drawer adjacent to the wall or cabinet opening. Connect the power supply cord to the
electrical outlet.
2. Carefully insert the drawer into the prepared opening, ensuring that the cord is not pinched between
the oven and the wall.
3. Push the drawer in all the way until the mounting flange aligns flush with the cabinet's face. (Refer
to Figure 5 for visual guidance.)
4. Open the drawer and, using the pre-existing holes as a template, drill the cabinet with a 1/16" bit.
(See Figure 5 for details.)
5. Fasten the drawer in place using the four screws provided. (Illustration shown in Figure 6.)
Model and Serial Number Location:
• The model and serial numbers can be found on the nameplate, which is located inside the micro-
wave cavity, visible when the drawer is opened fully. The label is affixed to the back wall of the
microwave cavity and can be read from the flat surface.
Care, Cleaning, and Maintenance:
For detailed cleaning instructions, refer to the Operation Manual.
(Images or figures referenced in the text, such as Figure 5 or Figure 6, are not displayed here but would
provide visual assistance in the actual installation process.)
Screws
Mounting flange
DRAWER INSTALLATION
Do not use an extension cord. If the power supply cord is too short, an outlet should be installed near
the appliance by a qualified technician.
Figure 6
Figure 5
Koolmore Supply, Inc. extends a limited warranty to the original purchaser, guaranteeing that this
Koolmore
product is free from manufacturing defects in material or workmanship for one year from the date of
purchase.
Should you discover any such defect within the warranty period, Koolmore Supply, Inc., reserves the
right to
repair or replace the product without charge, or to cover the cost of replacement parts and repair labor
needed
to correct defects present at the time of purchase or resulting from regular usage, when the appliance
has been
installed, operated, and maintained as per the instructions provided.
At its sole discretion, Koolmore Supply Inc. may decide to replace the product. In such an event, your
replacement
appliance will carry the warranty for the remaining term of the original unit's warranty period.
This warranty is valid exclusively to the original purchaser of the product and only applicable within the
United
States. The warranty commences from the date of original consumer purchase. Proof of the original
purchase
date will be required to obtain service under this warranty.
Under this limited warranty, your sole and exclusive remedy will be product repair, as outlined above. All
services must be provided by a Koolmore-designated service company.
To claim warranty or request repair service:
Email support@koolmore.com. Please include your name, address, phone number, warranty repair
request,
and a copy of your proof of purchase receipt. Alternatively, visit koolmore.com and use the contact us
page. A
Koolmore customer service representative will promptly arrange service for your appliance.
We thank you for choosing Koolmore.
This limited warranty will not cover:
1. Failure of the product to perform during power failures or interruptions,
or due to inadequate electrical service.
2. Damage incurred during transportation or handling.
3. Damage caused by accidents, vermin, lightning, winds, re, oods, or acts of God.
4. Damage resulting from accidents, alterations, misuse, abuse, improper installation, repair, or mainte-
nance.
This includes using any external device that alters or converts the voltage or frequency of
electricity.
5. Unauthorized product modications, repairs by unauthorized centers, or use of non-approved
replacement parts.
6. Abnormal cleaning and maintenance not aligned with the user's manual.
7. Use of incompatible accessories or components.
8. Any costs associated with repairs or replacements under these excluded circumstances shall be the
responsibility of the consumer.
Table of contents
